EBA 430 E EBA 430 EP. Operating Instructions
|
|
- Ernest Carpenter
- 6 years ago
- Views:
Transcription
1 EBA 430 E EBA 430 EP Operating Instructions
2 EBA 430 E EBA 430 EP Dear customer, Thank you for choosing a paper cutting machine from EBA. With the purchase of this quality product you can be sure you have made a good choice. Please read these operating instructions before putting the machine into operation and observe the safety regulations. -2-
3 EBA 430 E EBA 430 EP Read through the operating instructions carefully Table of contents Pages Safety precautions 4 11 Installation Operation Blade replacement Maintenance and cleaning Possible malfunctions Accessories 43 Manufacturer s Declaration 45-3-
4 EBA 430 E EBA 430 EP Children must not operate the machine! Paper clips or hard material will damage the cutting blade! Do not cut hard materials or materials which may splinter! -4-
5 The machine must be installed on a sturdy, dry and level floor! The machine must not be located outside! Do not use in the vicinity of inflammable liquids or gases! -5-
6 EBA 430 E EBA 430 EP The machine may only be used for cutting paper or similar materials! Never leave the blade unattended. Do not dismount or transport the blade without protection! Risk of injury! -6-
7 This machine is only constructed for "one-man operation"! Disconnect from the mains before starting any service work or before removing the panels! Replacement of blade and cutting stick may only be performed when the main switch is switched off! -7-
8 EBA 430 E EBA 430 EP A All components which may endanger the operator are covered by a guard! A A B Operating the machine without safety device (front safety guard (A), rear screwed safety guard (B) and panel (C) is forbidden! C A C -8-
9 The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B) A B A Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A),(correct if distance between cover and table is < 15 mm) main switch (B) and control panel (C) must be checked. B 15mm 0.59inch C -9-
10 EBA 430 E EBA 430 EP Protect mains cable against heat, oil and sharp edges! 230 V / 10A min 115 V / 15A min Connect the power cord to a single phase socket Ensure free access to mains -10-
11 -11- When not in use for a longer period switch off. (Main switch to "0").
12 EBA 430 E EBA 430 EP A Unpack the cabinet (A), (accessories) or stand (B), (accessories) and assemble according to the enclosed separate instructions. B 1. 2 strong people are required to lift the machine onto the cabinet or stand. Beware of fingers! Risk of injury!
13 B Only on EBA 430 E Screw on the backgauge crank (A) and operating handle (B) (found together with tools in the tool set). C A Plug into socket. -13-
14 EBA 430 E EBA 430 EP A A A It is not allowed to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices upon their function and completeness before working with. All covers have to be mounted (A). The release for cutting is allowed only if the cover is closed and the two-hand safety device is operated at the same time (B) The front cover should not close by itself (otherwise please adjust the hexagonal screw at the right and left(c). (Remove the cover) (D). We recommend to keep a test result booklet. B B D C -14-
15 D Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use. Only EBA 430 EP Press S button (D). (Reference point is driven to). C A B -15-
16 EBA 430 E EBA 430 EP EBA 430 E EBA 430 E The backgauge has to be adjusted by the handle with calibration ring (A). Measurement has to be adjusted from the rear. A EBA 430 EP E D C EBA 430 EP The graduation is done manually via the handle with calibration ring (B) or by programming (C) the cutting measurements. (If Display shows "C" the pressure lever (D) has to be moved to the right, so the backgauge (E) is moving). B -16-
17 EBA 430 E EBA 430 E Measurement is indicated on the back side-lay (A). The fine adjustment is achieved by using the calibration ring (B). The scale is divided in mm (One complete turn corresponds 10 mm = 1 cm). B A EBA 430 EP C EBA 430 EP Measurement is shown in the display of the control device in inches or cm (C). -17-
18 EBA 430 E EBA 430 EP A Optical cutting line (A) that indicates the exact position of the cut.(only use when no exact cut is required). Only for EBA 430 E Change of measurement through oversight is avoided by pulling out the lever. -18-
19 A Position the paper on the back gauge (A) and side-lay (B). To move paper stacks, please use the stacking angle (C). (Run backgauge to the front for turning the paper stack). B C Close the safety guard. -19-
20 EBA 430 E EBA 430 EP Before every cut the lever must be pushed to the left and tightened with light pressure. Press both buttons of the two-hand activation (A) simultaneously and keep them pressed until the paper is completely cut. A Cutting stop or interruption Release one or both buttons (A) of the twohand control. A -20-
21 cm inch Operating elements A - Guard front B - Safety two-handed control system C - Overload switch (Blade drive/backgauge drive) D - Backgauge control E - Clamping F - Main switch G - Handwheel for backgauge setting H - Key switch I - Backgauge J - Side gauge left K - Display cutting size (cm or inch) L - Select program step down M - Select program step up N - Stop and delete input O - Start P - Eject function Q - Keypad R - Changeover cm/inch S - Clear program T - Select program U - Enter V - Program number W - Program step X - Specified size -21-
22 EBA 430 E EBA 430 EP cm inch cm inch -22- EBA 430 EP Start machine Main switch F to position "I", insert the key H for the control panel and turn it to the right. Open the safety Front guard A Press S button O backgauge I moves to the rear and searches for the reference position, wait until a measurement of 38,5 cm or 15,16 inch is shown in the display D. Warning! Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) is stored. How to store see below picture on the left. Dimensions control - cutting to specified dimensions Enter dimension at the numerical key pad Q LED "S" X appears. Press S button dimension is approached, LED "S" disappears. Dimensions below 9 cm can only be approached with the S button held pressed. (When the start button O is released, the backgauge I moves to a measurement of 9 cm measurement 9 cm blinks, now push again the start button, backgauge I moves to for example 7 cm). Insert paper and move by means of the stacking angle to the backgauge I and side lay at the left J. Close the safety guard A. Move the pressing lever E to the left by a slight swing. Release the cutting. Cut according to markings Adjust the backgauge with the hand-wheel G to the back. Insert paper and move by means of the stacking angle to the backgauge I and left side-lay J. Turn rotary control G to the right until the marking on the paper to be cut is below the cutting line indicator. The further the rotary control is turned to the right, the faster the backgauge moves. Return of the backgauge is quick by turning the rotary control to the left. Close the safety guard A.
23 Move the pressing lever E to the left by a slight swing. Release the cut. Eject function If the z button is kept pressed the backgauge I moves to a measurement of 9 cm (Basic adjustment) and when released the z button returns to the measurement last set. If the z button is released while the backgauge moves to the front, the backgauge stops and moves back to the measurement which has been set last time. Cutting activation Warning! Run backgauge to the front for turning the paper stack. Do not interrupt the upward movement of the blade by performing switching procedures. Release blade only when LED "S" has gone out. Close the front guard A. Blade must always be at the top and be covered by the clamp. Do not touch the blade - risk of injury! (see security information on page 34). -23-
24 EBA 430 E EBA 430 EP cm inch Programming only EBA 430 EP This control system enables you to store 9 programs with 9 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with the button r and h. First figure in display = program number, Second figure = program step. Dimensions below 9 cm can only be approached with the S button held pressed. u on the Display the entered dimension is too low. (Smallest measurement 3,5 cm). o on the Display the entered dimension is too high. (Largest measurement 38,5 cm). Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off. Should you change to another dimension unit all programmed measures are converted into the new unit (cm and inch). cm inch Entering a program Press p P appears in the Display Enter program number (First figure in Display = program number). Enter dimension, or move the backgauge to the desired measurement with the rotary control. g Store the dimension next program step appears. Enter the next dimension. (should an ejection be desired before this cut push the z button, measurement and eject function are stored now). g Store the dimension. Should the entered program be required immediately Press S (program is closed). Press S again (backgauge moves to the dimension of the 1st program). Or: p + s Escape the program mode The eject function must be programmed in the 1 st dimension if the paper stack should be ejected at the end of a program where several cutting processes are made.
25 Eject function Set the measurements push the z button. g Store the dimension. Backgauge moves in the program for unloading paper to the front and then to the measurement which has been set in the panel. Cancel a program p Press P appears in the display Enter program number Press c twice. Each program has to be cancelled separately. Single program steps can only be overwritten. Deleting the last program step Press 0. Press g. p + s Escape the program mode. Working with programs Press p P appears on the display Enter Program number With the button r and h you are able to change between several program steps. With S the backgauge moves to the indicated dimension. With s the backgauge stops. General LED "S" blinks the basic position will appear. LED "S" is off the actual dimension appears. In the program mode the ejection of paper z is not possible. The ejection of the paper has to be programmed. After each cut pressing the button S the backgauge moves to the next dimension. Escape the program mode Press p P appears on the display. Press s Escape the program mode. Program buttons h and r programms By means of buttons h and r dimension of your choice can be reached. (Basic adjustment h = 38,5 cm, r = 9 cm). p and simultaneously h resp. r ( h U resp. r D appears on the display. Insert the desired dimension. g Store dimension. Display in cm or inch Press i Display changes between cm and inch. (See picture left). Adjust the eject-dimension The eject dimension is programmed to 29,50 cm. It may be changed as follows: Press p Press p + z e on Display. Insert the desired dimension. g Store dimension. -25-
26 EBA 430 E EBA 430 EP If the cutting quality decreases: Check the cutting depth (see page 34). Check the cutting stick (see page 30). Replace or grind the cutting stick (see page 26-34). The blade may only be grinded by a qualified workshop or from the manufacturer Krug & Priester, D Balingen. Danger! Risk of injury The blade is extremely sharp. Do not dismount or transport the blade without protection. Changing the blade may only be performed by trained staff. -26-
27 Turn the blade depth adjustment screw to the left until it stops (Screwdriver found in tool set). Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.)
28 EBA 430 E EBA 430 EP The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench (A) (found in tool set). Until the red arrow-like eccentric marking corresponds to the position "0" (B). A B Remove the special wrench and turn on the main switch until the blade returns to the home position. Danger! Do not put main switch on position "0" whilst blade is moving upwards! The clamp must always overlap the blade! Risk of injury! Clamping OK Blade OK -28-
29 Remove the 2 blade screws (1.). Then put the blade changing tool (2.) into place and fasten it to the blade The remaining screws should then be removed (1.). Loosening the grips of the blade changing tool lightly (2.) will now allow the blade to be taken downwards out of the machine (3.)
30 EBA 430 E EBA 430 EP If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times). Danger! Risk of injury!
31 A Screw the exchange blade to the blade changing tool as follows: (A) make sure there is a space ot 4-5 mm or inches (B). blade must be covered (C). B 4-5 mm inch C B Place the blade to be exchanged with the blade changing tool mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.)
32 EBA 430 E EBA 430 EP 1. Lightly tighten 3 of the 5 blade screws (1.) (with washers), remove the blade changing tool (2.) and lightly tighten the remaining blade screws (with washers) (3.) Remove all tools and distribute paper along the entire cutting length. -32-
33 1. Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.). Open the safety guard (4.). With the special wrench (B) the 3 eccentrics shall be screwed so far down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick) A Turn main switch to position I. (1.) The blade will return to the upper position and the blade screws should be tightened firmly (2.)
34 EBA 430 E EBA 430 EP A Cut a stack of paper to test. If the last sheet has not been cut through move the knob for the adjustment of the blade depth setting (A) to the right (about ½ - ¾ turn if maximum of stacking height is going to be cut - the blade is set lower - do not set it too low, blade will become dull sooner. Danger! Blade must always be covered by the pressing bar (see picture below at the left). Clamping OK Blade OK -34-
35 Maintenance work may only be performed by trained staff. Disconnect the mains before starting any service work or before removing the cover. B A Oil the backgauge (A) control weekly i.e. grease it. (Use non-resinous oil and grease). Twice a year the remaining 14 grease parts (B) (see picture). To do this switch please bring the main switch to position "0" (E) and move the machine on its left sidfe. Danger! of tilting! Remove cover (C) and lower panel (D) (tools in tool set). Remove remaining paper Grease the machine Check the two joining bolts and pushing bar for wear Mount the machine upright D F E C -35-
36 EBA 430 E EBA 430 EP Safety check According to 40 VBG 7i a safety check according to the safety stipulations has to be made every 5 years by a service team authorised through our service department. The carrying-out of such a check has to be attested on the test certificate. A corresponding test label must be visible and affixed to the machine. In Germany such a safety check is regulated and we recommend it for all other countries, too. -36-
37 Machine does not function Machine is plugged in? Main switch to position "I"? Control system activated? (Turn key to the right) A B -37-
38 EBA 430 E EBA 430 EP Machine turns off: EBA 430 E and EBA 430 EP Extreme load of machine (cooling phase. Security switch (A) turns off. About 1 minute, push the safety button (A). Machine blocked Blade is dull Eliminate the disturbance, push the safety button (A). EBA 430 EP only: Safety button (B) jumps out. Backgauge blocked Safety button (B) jumps out. Eliminate disturbance, push the safety button (B). A B -38-
39 A Does not cut through the last sheet: Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B) Poor cutting quality or blade stays in the paper stack. change the blade (C) (see page 26-34). B C -39-
40 EBA 430 E EBA 430 EP EBA "Service" Motor runs but blade does not move downwards. Security brake has been activated! Inform the service team! "Service" service@krug-priester.com A Display illumination off Machine is plugged in? (A) Main switch on position "I"? (B) Key turned to the right?(c) Push in the security button! (D) Check the fuse of the buildings electrical installation! C D B -40-
41 EBA 430 E Cut cannot be made. If cover is open: close it. If cover is closed: open and re-close it. (Security check). EBA 430 EP Cut cannot be made. Measurement has not been driven to correctly. LED "S" X does not turn off. Push again the S button. Security check of the cover (see above) Measurement below 9 cm Hold the S button O until the measure is achieved. Backgauge I does not move, the display shows " C" Turn the pressing lever E to the right. cm inch Backgauge I does not move to position (pressing lever has been turned to the right). " C" is in the display inform service people. -41-
42 EBA 430 E EBA 430 EP EBA "Service" None of the above mentioned methods helped to solve the problem: Contact Service team under "Service" service@krug-priester.com Subject to alterations without notice. -42-
43 Recommended accessories: Blade Nr Cutting stick (6 pieces) Nr Paper knock-up block Nr Blade changing tool Nr Cabinet Nr Stand Nr
44 EBA 430 E EBA 430 EP Remarks: -44-
45 MANUFACTURER S DECLARATION This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 98/37, 73/23 and 89/336. EBA is certified under the DIN EN ISO 9001 quality standards. The exact technical specifications can be found on the technical specifications sticker on the machine. A wiring diagram is found in the electric switch box. Applied standards and technical specifications: 230 Volt-Version: EN 292; EN 294; EN 349; EN 27779; EN ; EN ; EN 60204; EN ; EN ; pren ; pren Sound level information: The sound level is 71 db (A) as defined by DIN 45635/Teil 27. Wolfgang Priester -General Manager- -45-
46 EBA Made in Germany Document Shredders Trimmers and Guillotines EBA Krug & Priester Balingen Germany Printed in Germany EBA 04/2002 D
Cut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More informationQuick Set Dovetail Jig
Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT
More informationTUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL
TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL 1 CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine s Description and Purpose of Use 3 2.1. Machine s description
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS Rotary Microtome CUT 4062 / CUT 5062 / CUT 6062 CUT 6062 illustrated above INS1000GB 2012-01-06 Instructions CUT4062 / CUT 5062 / CUT 6062 2 CONTENTS 1. INTENDED USE... 4 2. SYMBOLS...
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationVARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL
VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4
More informationFOLDING MACHINE PF-45A OPERATOR MANUAL 1. FUNCTION
FOLDING MACHINE OPERATOR MANUAL 1. FUNCTION The folding machine is used to fold documents stand alone or in combination with a system 7. Sheets can be folded in various types. These are: single fold; letter
More informationDuplo 660 Guillotine Paper Cutter Installation / Operation Manual
Duplo 660 Guillotine Paper Cutter Installation / Operation Manual 1 2 Contents PARTS LIST:... 5 TOOL KIT LIST:...5 INSTALLING THE SIDE TABLES:... 6 TABLE SQUARING:... 7 OPERATING PROCEDURE:...8 TO ADJUST
More information7. Operating instructions: EFL 300
7. Operating instructions: EFL 300 Copyright 2015 by Endecotts Ltd. 59 1. Setting up Technical specifications SIEVE SHAKER MODEL: EFL 300 General Information The new EFL 300 combines the best features
More information6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL
4511 WAYNE AVENUE PHILADELPHIA PA 19144 TEL: 888-800-2663 FAX: 800-582-9643 6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL CONTENTS I. INTRODUCTION TO BOND PCC-6 / MACHINE SPECIFICATIONS II. SAFETY PRECAUTIONS
More informationEllisSaw.com. EllisSaw.com P.O. Box Verona, WI
P.O. Box 9019 Verona, WI 9-019 GENERAL OPERATING & SAFETY INSTRUCTIONS * READ INSTRUCTIONS BEFORE USE * CAUTION: Disconnect power supply cord from power source when doing repair work or changing belt.
More informationGENERAL OPERATIONAL PRECAUTIONS
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More information12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)
1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22
More informationGENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationFirst published : May 1997 Fourth edition : January No
First published : May 1997 Fourth edition : January 2006 No. 050153 INTRODUCTION Thank you for your purchasing Kansai Special's FX Series. Read and study this instruction manual carefully before beginning
More informationElectric Chainsaw Sharpener
FPP CHAINSS Electric Chainsaw Sharpener Instruction Manual For your own safety, please ensure you have read these instructions before use and have fully understood all the safety guidelines. Specifications
More informationCONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------
More informationBending Roll Machine 4126
Bending Roll Machine 4126 Operating Instructions Table of contents Main components...4 Operation...5 Safety...7 Service and maintenance... 12 Machine plates and stickers... 13 Dismantling the bending
More informationOperating Instructions K-POWERgrip EWL Always on the safe site.
Operating Instructions K-POWERgrip EWL 4941. Always on the safe site. KaVo Elektrotechnisches Werk GmbH Wangener Straße 78 D-88299 Leutkirch A 1 User information...2 A 1.1 Meaning of the pictograms...2
More informationFUNCTIONAL DESCRIPTION
FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. Some illustrations in this Instruction
More informationTapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
More informationOPERATING INSTRUCTIONS
GB OPERATING INSTRUCTIONS Automatic Wedge Welding Machine Please read operating instructions carefully before use and keep for further reference. APPLICATION The is an automatic wedge welding machine for
More informationTranslation of the Original Operating Manual. AutoCUT 500
Translation of the Original Operating Manual Contents Page Original operating instructions... 3 Table of Contents Foreword... 4 Instructions for use................ 4 Copyright.........................4
More informationKWIKFOLD User Manual
KWIKFOLD User Manual English X2 1 2 3 4 5 7 X1 Ernst Nagel GmbH: Gebrauchsanleitung 2002-06-13 eng.doc 2/16 Introduction Your Foldnak 40 bookletmaker uses the Foldnak principle: stapling and folding in
More informationELECTRIC SLIP ROLL MACHINE. Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0
ELECTRIC SLIP ROLL MACHINE Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0 Operation Manual Table of contents I MAIN SPECIFICATION...2 II SAFETY INSTRUCTIONS.. 2 III OPERATION INSTRUCTIONS..4
More informationKnife grinding machine K3 H/K
Knife grinding machine K3 H/K 01.11.2010 GS-Schleiftechnik, Leyher Str. 61 a, D-90431 Nürnberg Phone 0049/9193/4404, Fax 0049/9193/4391 e-mail: info@gs-de.eu 1 Table of Contents A. SAFETY... 3 A.1 THE
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationTop spin Nr /
Top spin Nr. 1840 0000 / 1840 1000 Bedienungsanleitung 21-6680 28052014 / A Made in Germany Ideas for dental technology Top spin Nr. 1840 0000 / 1840 1000 Contents 1. Introduction...2 1.1 Symbols...2 2.
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL BladeRunner X2 WX572 9 10 8 11 5 7 12 6 20 1 2 4 3 14 13 15 A2 A1 17 18 B2 B1 1 2 1 2 19 B3 3 4 2 C 1 D1 D1 C 2 1 E1 D2 1 2 E2 1 2 F G1 G1 F OFF ON G2 G3 H1 H2 I1 I2 I1 I2 J
More informationMEC Auto-Mate Assembly Manual. For MEC 9000G/GN and 8567 Grabber Series
MEC Auto-Mate Assembly Manual For MEC 9000G/GN and 8567 Grabber Series Thank you We really appreciate your support of our product line. But our commitment to you hardly ends here. We won't be satisfied
More informationANGLE GRINDER STAND USER GUIDE AFTER SALES SUPPORT
ANGLE GRINDER STAND USER GUIDE Important: retain for future reference - please read carefully. Now you have purchased a WORKZONE product you can rest assured in the knowledge that as well as your 1 year
More informationSMALL GAUGE NIBBLER ASSEMBLY & OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web Site at
SMALL GAUGE NIBBLER 91739 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights reserved.
More informationROTARY HAMMER OWNER S MANUAL
ROTARY HAMMER OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationINSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN
INSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN DWX723-XE MITER SAW STANDS Components List A. Beam B. DW7231 Miter saw mounting brackets C. Extension arm D. DW7232
More informationOperator Manual. Booklet Maker BM 60. Doc No. T10171
Booklet Maker BM 60 Operator Manual Doc No. T10171 Morgana Systems Limited United Kingdom www.morgana.co.uk Telephone: ( 01908 ) 608888 Facsimile: ( 01908 ) 692399 Part no: 60249 Doc no: T10171 Rev. date:
More informationHedge Trimmer Attachment HA 110 HA 850 Complément Taille-haie HA 110 HA 850 Tijeras cortasetos (suplemento) HA 110 HA 850.
Operator s manual Manual d utilisation Manual de instrucciones Hedge Trimmer Attachment HA 110 HA 850 Complément Taille-haie HA 110 HA 850 Tijeras cortasetos (suplemento) HA 110 HA 850. GB English FR ES
More informationCOMPLEX GRINDER OF MILL& DRILL
COMPLEX GRINDER OF MILL& DRILL MODEL: MR-F6 OPERATING INSTRUCTION PLEASE REMEMBER 1. When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk
More informationINSTRUCTIONS FOR INSTALLATION AND SERVICE OF ZF3000 EXTERNAL BLIND
R INSTRUCTIONS FOR INSTALLATION AND SERVICE OF ZF3000 EXTERNAL BLIND Before starting installation of the external blind, please read the following instructions. During transportation and storage, the
More informationHedge Trimmer Attachment HA110 HA850 Complément Taille-haie HA110 HA850 Tijeras cortasetos (suplemento) HA110 HA850
Operator s manual Manual d utalisation Manual de instrucciones Hedge Trimmer Attachment HA110 HA850 Complément Taille-haie HA110 HA850 Tijeras cortasetos (suplemento) HA110 HA850 GB FR ES KEY TO SYMBOLS
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationDaily Maintenance. 2. Insert bobbin cases in to rotary hooks. Make sure bobbin thread is not over 2 inches long. Close bobbin case covers.
Rotary hook 1. Open bobbin case covers and remove bobbin cases. Use brush to remove lint build up in and around rotary hooks. Compressed air may also be used. Daily Maintenance Cle aning Oiling Rotary
More information10 x 6 Planer/Thicknesser
01550 10 x 6 Planer/Thicknesser Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. 1 Specifications 2 Safety Rules.3-4 Unpacking.5
More informationDust Collector. Model No: DC2200 (FM300S)
Dust Collector Model No: DC2200 (FM300S) GENERAL SAFETY INSTRUCTIONS Before attempting to operate this machine, it is important that you read, understand and follow these instructions very carefully. They
More informationINSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER
INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER Part No.: SW1250 PLEASE READ CARE AND SAFETY INSTRUCTIONS BEFORE USE SPECIFICATIONS Part No.: SW1250 Input Voltage: 240V Frequency: 50Hz Rated
More informationS E L E C T I O N. Upper Back. User manual
and S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual and and The identification plate of the and manufacturer, affixed to the frame on the side opposite the padded rest, gives the
More informationLassco Spinnit EBM-S Paper Drill
Lassco Spinnit EBM-S Paper Drill User's Manual Provided By http://www.mybinding.com http://www.mybindingblog.com Before operating this equipment, please read these instructions completely and keep these
More informationThorvie Instructions Always wear eye protection and do not wear loose clothing when operating machinery. FOR AV- 41 ICE AUGER MACHINE
FOR AV- 41 ICE AUGER MACHINE 1. Please study video and all instructions before proceeding to grind. For Mora, Jeffy and Eskimo blades use the 6 brown resin bond wheel. Mount with washer and left-hand nut
More informationHedge Trimmer Attachment Complément Taille-haie Tijeras cortasetos (suplemento) Operator s manual Manual d utalisation Manual de instrucciones
HÄcksaxtillsats HA110 HA850 Jonsered Hedge Trimmer Attachment Complément Taille-haie Tijeras cortasetos (suplemento) GB FR ES Operator s manual Manual d utalisation Manual de instrucciones KEY TO SYMBOLS
More informationplaner/thicknesser 200 x 120mm
instructions for planer/thicknesser 200 x 120mm model no: sm1311 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
More informationFBX-PA-2AC. Third edition : April No
FBX-PA-2AC Third edition : April 2006 No. 060058 INTRODUCTION Thank you very much for purchasing Kansai Special FBX series. Read and study this Instruction Manual carefully before you start any of the
More informationTABLE OF CONTENTS. Page. 1. General Installation & Method Operation Adjusting Instruction Maintenance 4 6.
www.lmine.com TABLE OF CONTENTS Page 1. General 3 2. Installation & Method 3 3. Operation 3 4. Adjusting Instruction 4 5. Maintenance 4 6. Drawings 5 & 6 1. General This test method determines the particle
More informationCOFFEE LABORATORY WHITE STONE VA TEL
1. Technical specifications 4. Operating instructions: Octagon 200 Copyright 2015 by Endecotts Ltd. 21 1. Setting up Technical specifications SIEVE SHAKER MODEL: Octagon 200 General Information The sieve
More informationGENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationMBM Sprint 3000 Booklet Maker
MBM Sprint 3000 Booklet Maker Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com SPRINT 3000 BOOKLETMAKER OPERATION MANUAL IMP oper3500.doc Page 1 23/01/2004 CONTENTS
More informationSERVICE MANUAL FOR HOMELOCK M1034D 2034D 1134DW 1134D
SERVICE MANUAL FOR HOMELOCK M1034D 2034D 1134DW 1134D 11.2000 2.2012 I HOW TO USE THIS MANUAL... 1 II HOW TO ADJUST... 2 1. Height of needle bar... 2 2. Position of the lowerlooper... 3 3. Timing of the
More informationCut-Off Machine Model CC 14SE
Cut-Off Machine Model CC 14SE Handling instructions NOTE: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended
More informationElectric Staple/Nail Gun
Electric Staple/Nail Gun Model CESN120 Part Number 3110292 Operating & Maintenance Instructions 0305 Specifications Model No... CESN120 Part No... 3110292 Power Input... 230V, 50Hz, 1Ph Watts... 600 Fuse
More informationWX8800 WX8700 LX5801 WX8842 WX MC30
WX8800 WX8700 LX5801 WX8842 WX8842-1 MC30 First published : August 1991 Third edition : August 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's WX Series. Read and study this
More informationInstruction Manual. Manual Furniture Mover. Note: Owner/Operator must read and understand this instruction manual before using the furniture mover.
Instruction Manual Manual Furniture Mover Note: Owner/Operator must read and understand this instruction manual before using the furniture mover. I - Contents 1. Application 2 Specifications 3.Assembly
More informationOperation Manual ARTICEL 51251
Operation Manual ARTICEL 51251 Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations,
More informationSERVICE MANUAL AND PARTSLIST
SERVICE MANUAL AND PARTSLIST Next 20 CONTENTS WHAT TO DO WHEN... 1~3 SERVICE ACCESS FACE COVER... 4 TOP COVER... 4 BASE COVER... 5 REAR COVER... 6 FRONT COVER... 7 MECHANICAL ADJUSTMENT NEEDLE THREAD TENSION...
More informationMakerspace Student Machine Safety and Usage Manual
Makerspace Student Machine Safety and Usage Manual Prepared by: Thiago De Oliveira (2016-2017) Queen s University Last Updated: 21 st October 2016 General Safety Rules and Guidelines 1. Wear APPROPROPRIATE
More informationGENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING DISC GRINDER
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationQUICK CONNECT SYSTEM IMPACT DRIVER ATTAChMENT www.blackanddecker.com.au Australia BDCMTI-XE New Zealand PARTS AND FEATURES 1. Impact Driver attachment 2. 6.35 mm (1/4 ) hex quick-release chuck 2 1 Additional
More informationFLEXRISE2 VERSION. 2 LEG / 2 MOTOR ELECTRIC TABLE BASE (36 to 72 ) **PATENT PENDING**
FLEXRISE2 2 LEG / 2 MOTOR ELECTRIC TABLE BASE (36 to 72 ) VERSION A INSTRUCTION MANUAL CONTENTS: FLEX-MU-2L3S-C3672-K4# FEET-ADJ-UNV-2430# **PATENT PENDING** MAX Load 265 lbs (120 KG) Equally Divided MAX
More informationHorizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115
Horizontal and Vertical Metal Cutting Band Saw MODEL: BS-5 SAFETY. Know your band saw. Read the operator s Manual carefully. Learn the operations, applications and limitation.. Use recommended accessories.
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire
More information3-1/4 HP VARIABLE SPEED PLUNGE ROUTER
IMPORTANT INFORMATION 2-YEAR LIMITED WARRANTY FOR THIS PLUNGE ROUTER KING CANADA TOOLS OFFERS A 2-YEAR LIMITED WARANTY FOR NON-COMMERCIAL USE. 3-1/4 HP VARIABLE SPEED PLUNGE ROUTER PROOF OF PURCHASE Please
More informationAngle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
More informationTube Facing Tool.
www.swagelok.com Tube Facing Tool This manual contains important information for the safe and effective operation of the Swagelok TF72 series tube facing tool. Users should read and understand its contents
More informationFerm Table Drilling Machine FTB-13. Art.nr Screwfix Art.nr Ferm BV P.O. Box AC Genemuiden NL
UK Subject to change USER S MANUAL Document Ref: FTB-13/19847/PMR24/Issue 1/April 02 Copyright These instructions are the sole property of Ferm-Omega Tools and may not be reproduced Ferm Table Drilling
More informationSERVICE MANUAL PARTS LIST MODEL: NH40
SERVICE MANUAL & PARTS LIST MODEL: NH40 CONTENTS What to do when... 1-3 SERVICE ACCESS Face Cover... 4 Bed Cover... 5 Free-arm Cover... 6 Front Cover... 7 Rear Cover... 8 MECHANICAL ADJUSTMENT Presser
More informationElderfield & Hall, Inc., Kama Bandsaw AD 105S. Instruction Manual: Introduction to the Manual. General Precautions. Equipment. Machine.
Elderfield & Hall, Inc., www.kooltools.com 10901 McBride Lane, Knoxville TN, 37932. Phone: 865.671.7682. Fax: 865.671.7686. Email: bob@kooltools.com Kama Bandsaw AD 105S 110 Volt, Single Phase 2 ¼ HP Portable
More informationOPERATIONAL MANUAL V1.0. Removing/Replacing Blades
OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90
More informationHAPPY HCS Voyager: Level-1 Maintenance & Repair Intermediate-level repair / maintenance procedures
TEXMAC Inc. HAPPY HCS Voyager Introduction Training page 1 HAPPY HCS Voyager: Level-1 Maintenance & Repair Intermediate-level repair / maintenance procedures Table of Contents Oiling/Cleaning Page 2 Removing
More informationInstruction Manual HPP-570 HBB-532 HBB-538
Instruction Manual HPP-570 HBB-532 HBB-538 Read, understand and follow all safety instructions and operating procedures. If you do not understand the instructions or if conditions are not correct for proper
More informationS E L E C T I O N. Arm Curl. User manual
S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual The identification plate of the and manufacturer, affixed behind the seat, gives the following details: A Name and address of the manufacturer
More informationMOTOR REPLACEMENT : STEP BY STEP.
(D) REPLACEMENT : STEP BY STEP. (V) Adjustment screw (Allen key 3/16 ) (E) (U) (I) Tightening screw (Allen key 5/32 ) Blocking screw (H) (Allen key 5/32 ) (G) (Y) (T) (ZZ) (Z) (K) (X) (L) (S) (W) (R) (Q)
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationInstruction Manual 13MM DRILL PRESS. Model SROM1199. Our tool range has you covered for DIY. Whatever the job, make light work of it with MAKO tools.
Instruction Manual 13MM DRILL PRESS Model SROM1199 Our tool range has you covered for DIY. Whatever the job, make light work of it with MAKO tools. PRODUCT FEATURES: 1. Pulley Cover 9. Feed Handle 2. Motor
More informationRecipro Saw MODEL JR3020. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Recipro Saw MODEL JR3020 002479 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationDRILL BIT SHARPENER MODEL NO: CBS43 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0710
DRILL BIT SHARPENER MODEL NO: CBS43 PART NO: 6480232 OPERATION & MAINTENANCE INSTRUCTIONS LS0710 INTRODUCTION Thank you for purchasing this CLARKE drill bit sharpener. Before attempting to use this product,
More informationCordless Power Planer
ENGLISH Cordless Power Planer MODEL 050D 00540 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS
More informationINSTALLATION MANUAL GIOTTO SCREEN
INSTALLATION MANUAL GIOTTO SCREEN Before installing the Giotto screen, please read the following instructions carefully: The Giotto screen must be used INDOORS ONLY. It is forbidden to stay under the Giotto
More informationx 36 Wood Lathe
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
More informationHOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL
HOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL WARNING You must thoroughly read and understand this manual before operating the equipment, paying particular attention to the Warning & Safety instructions.
More informationJARVIS. Model BR-3 Blade Reconditioner ... EQUIPMENT TABLE OF
- Model BR-3 Blade Reconditioner EQUIPMENT SELECTION.......... Ordering No. TABLE OF CONTENTS............................ Page Model BR-3 (100 mm Blade) 115V/60Hz............ 4011003 220V/50Hz............
More information5 Maintenance 5.1 Guideway and Wipers
5 Maintenance 5.1 Guideway and Wipers 5.1 Page 26 of 41 The grinding carriage runs with hardened rollers on hardened steel straps (2). The steel straps (2) are positioned on the grinding bed (1) and tensioned
More informationOPERATION MANUAL. D-CUT WPC/LVP/VCT Cutter LP-330.
OPERATION MANUAL D-CUT WPC/LVP/VCT Cutter LP-330 www.dcutproducts.com SAFETY RULES FOR THE FLOORING CUTTER 1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
More informationFBX1104P FBX1104 FBX1106P FBX1106
FBX1104P FBX1104 FBX1106P FBX1106 Second edition : September 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's FBX Series. Read and study this instruction manual carefully before
More informationCHAPTER 52 ELECTRICAL POWER TOOLS
CHAPTER 52 ELECTRICAL POWER TOOLS HOW TO CHOOSE AND USE THEM The Types and Uses pages provide you with a list of the electrical power tools found in the pioneer tool outfit. These pages should help you
More informationGrinding drill machine OPERATION MANUAL - 1 -
Grinding drill machine OPERATION MANUAL - 1 - Index: I. Safety Notification P.4 II. Machine Devices Introduction P.9 III. Machine Installation Instruction P.11 IV. Standard Operational Steps P.13 V. Replacement
More information3 IN 1 HEAVY DUTY TILE CUTTER. Model Visit our website at:
3 IN 1 HEAVY DUTY TILE CUTTER Model 41711 ASSEMBLY Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in
More informationx 43 Wood Lathe
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
More informationSubject to change. USERS MANUAL Art.nr. PRM6006 PBF-1050N
UK Subject to change UK USERS MANUAL Art.nr. PRM6006 PBF-1050N 0406-14 EXPLODED VIEW Fig. D Fig. A Fig. E Fig. B Fig. F Fig. C Fig. G 2 Powercraft Powercraft 11 SPARE PARTS LIST PBF-1050N REF NR DESCRIPTION
More informationEMO. Service Instruction. created by Frank Weithöner. Table of contents: Special Tools Assembling Mixing Chamber
EMO Service Instruction created by Frank Weithöner Table of contents: - Special Tools Disassembling Mixing Chamber Assembling Mixing Chamber Adjustment Rotor / Level Indicator Unit Temperature Compensating
More informationINSTRUCTION MANUAL. BELT SANDER 100mm AND DISC 150mm. (Fox Model F31-462A)
INSTRUCTION MANUAL BELT SANDER 100mm AND DISC 150mm (Fox Model F31-462A) 1 SUMMARY INSTRUCTION MANUAL 3-28 EXPLODED VIEW 29-30 WIRING SCHEME 31 DECLARATION OF CONFORMITY 32 2 Belt sander 100mm and disc
More informationINSTRUCTION BOOK AND PARTS LIST
Rag Cutter MODEL WE WARNING This machine is equipped with a very sharp knife. Keep hands, arms, and hair away from the knife area at all times. Misuse of this machine or failure to follow all safety instructions
More information