19456; Rev ; 8/1 EVALUATION KIT AVAILABLE GPS/GNSS Low-Noise Amplifiers General Description The / low-noise amplifiers (LNAs) are designed for GPS L1, Galileo, and GLONASS applications. Designed in Maxim s advanced SiGe process, the devices achieve high gain and ultra-low-noise figure while maximizing the input-referred 1dB compression point and the 3rd-order intercept point. The provides a high gain of 19dB. The supplies 15dB of gain while attaining higher linearity. The devices operate from a +V to +3.3V single supply. The optional shutdown feature in the devices reduces the supply current to less than 1FA. The devices are available in a very small, lead-free, RoHS-compliant,.86mm x.86mm x.65mm wafer-level package (WLP). Automotive Navigation Applications Telematics (Asset Tracking and Management) Personal Navigation Devices (PNDs) Cellular Phones with GPS Notebook PCs/Ultra-Mobile PCs Recreational, Marine Navigation Avionics Watches Digital Cameras S High-Power Gain: 19dB () S Ultra-Low-Noise Figure:.75dB () S Integrated 5Ω Output Matching Circuit S Low Supply Current: 4.1mA S Wide Supply Voltage Range: V to 3.3V S Low Bill of Materials: One Inductor, Two Capacitors S Small Footprint:.86mm x.86mm S Thin Profile:.65mm S.4mm-Pitch Wafer-Level Package (WLP) Features Ordering Information PART TEMP RANGE PIN-PACKAGE EWS+T -4NC to +85NC 4 WLP EWS+T -4NC to +85NC 4 WLP +Denotes a lead(pb)-free/rohs-compliant package. T = Tape and reel. / Typical Application Circuit V CC C2 V CC A1 A2 RFOUT RF OUTPUT R1 25kI RF INPUT C1 L1 RFIN B1 B2 SHDN OPTIONAL SHUTDOWN GND L1 = 6.8nH C1 = 1nF C2 = 1pF L1 = 6.2nH C1 = 1nF C2 = 1pF Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim s website at www.maxim-ic.com.
/ ABSOLUTE MAXIMUM RATINGS V CC to GND...-.3V to +3.6V Other Pins to GND...-.3V to (+ Operating V CC +.3V) Maximum RF Input Power... +5dBm Continuous Power Dissipation (T A = +7 C) 4-Bump WLP (derates 9.7mW/ C above +7 C)...776mW Maximum Current into RF Input...1mA Note 1: Refer to Application Note 1891: Wafer-Level Packaging (WLP) and Its Applications. CAUTION! ESD SENSITIVE DEVICE Operating Temperature Range... -4 C to +85 C Junction Temperature...+15 C Storage Temperature Range... -65 C to +16 C Lead Temperature (soldering, 1s)... Reflow Profile (Note 1) Soldering Temperature (reflow)...+26 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (/ EV kit, V CC = V to 3.3V, T A = -4NC to +85NC, no RF signals are applied. Typical values are at V CC = 2.85V and T A = +25NC, unless otherwise noted.) (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS Supply Voltage 2.85 3.3 V Supply Current SHDN = high 4.1 4.1 Shutdown mode, SHDN = low 1 µa Digital Input Logic-High (Note 3) 1.2 V Digital Input Logic-Low (Note 3).45 V ma AC ELECTRICAL CHARACTERISTICS (/ EV kit, V CC = V to 3.3V, T A = -4NC to +85NC, f RFIN = 1575.42MHz. Typical values are at V CC = 2.85V and T A = +25NC, unless otherwise noted.) (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS RF Frequency L1 band 1575.42 MHz Power Gain V CC = 2.85V (Note 4) V CC = V Noise Figure V CC = V to 3.3V In-Band 3rd-Order Input Intercept Point Out-of-Band 3rd-Order Input Intercept Point (Note 5) (Note 6) Input 1dB Compression Point (Note 7) 14.7 19 11.9 15.4 14.4 18.9 1 15.3.75.8-3 +4 +7-1 -6 Input Return Loss 8.5 db db db dbm dbm dbm 2
AC ELECTRICAL CHARACTERISTICS (continued) (/ EV kit, V CC = V to 3.3V, T A = -4NC to +85NC, f RFIN = 1575.42MHz. Typical values are at V CC = 2.85V and T A = +25NC, unless otherwise noted.) (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS Output Return Loss 15 db Reverse Isolation 4 db Note 2: Min and max limits guaranteed by test at and guaranteed by design and characterization at T A = -4 C and, unless otherwise noted. Note 3: Min and max limits guaranteed by test at. Note 4: Min limit guaranteed by design and characterization. Note 5: Measured with the two tones located at 1MHz and 2MHz offset from the center of the GPS band with -27dBm/tone for the and -24dBm/tone for the. Note 6: Measured with input tones at 1713MHz (-27dBm) and 1851MHz (-39dBm). Note 7: Measured with a tone located at 5MHz offset from the center of the GPS band. Typical Operating Characteristics (/ EV kit. Typical values are at V CC = 2.85V,, and f RFIN = 1575.42MHz, unless otherwise noted.) / S11-1 -15-2 -25-3 -35 INPUT RETURN LOSS vs. FREQUENCY toc1 GAIN 25 2 15 1 5 GAIN vs. FREQUENCY toc2 S12-2 -25-3 -35-4 -45 5-6 -65 REVERSE ISOLATION vs. FREQUENCY toc3-4 5 1 15 2 25 5 1 15 2 25-7 5 1 15 2 25 FREQUENCY (MHz) FREQUENCY (MHz) FREQUENCY (MHz) OUTPUT RETURN LOSS vs. FREQUENCY toc4 IN-BAND IIP3 (TWO TONES LOCATED AT 1MHz AND 2MHz OFFSET WITH -3dBm/TONE) -1 toc5-1 -2 T A = -4 C S22-15 -2-25 IIP3 (dbm) -3-4 -3-35 5 1 15 2 25-6 2. 2.2 2.4 2.6 2.8 3. FREQUENCY (MHz) 3
/ Typical Operating Characteristics (continued) (/ EV kit. Typical values are at V CC = 2.85V,, and f RFIN = 1575.42MHz, unless otherwise noted.) IN-BAND IIP3 (TWO TONES LOCATED AT 1MHz AND 2MHz OFFSET WITH -3dBm/TONE) 6 IIP3 (dbm) IIP3 (dbm) 5 4 3 2 1 T A = -4 C 2. 2.2 2.4 2.6 2.8 OUT-OF-BAND IIP3 (TONE 1 AT 1713MHz, -27dBm; TONE 2 AT 1851MHz, -39dBm) 12 1 8 6 4 2 2. 2.2 T A = -4 C 2.4 2.6 2.8 3. 3. toc6 toc8 IIP3 (dbm) INPUT P1dB (dbm) OUT-OF-BAND IIP3 (TONE 1 AT 1713MHz, -27dBm; TONE 2 AT 1851MHz, -39dBm) 2. 1.5 1..5 -.5-1. -1.5-2. -2.5-3. T A = -4 C 2. 2.2 2.4 2.6 2.8 3. INPUT P1dB COMPRESSION -6-7 -8-9 -1-11 -12-13 -14-15 -16 2. 2.2 2.4 T A = -4 C 2.6 2.8 3. toc7 toc9 INPUT P1dB (dbm) INPUT P1dB COMPRESSION -4-6 -7-8 -9 T A = -4 C -1-11 toc1 BLOCKER POWER (dbm) 5-1 -15-2 1dB GAIN DESENSE vs. BLOCKER FREQUENCY toc11-12 2. 2.2 2.4 2.6 2.8 3. -25 5 1 15 2 25 BLOCKER FREQUENCY (MHz) 4
TOP VIEW V CC RFIN WLP RFOUT (SHDN) BUMP NAME FUNCTION + A1 B1 Bump Configuration Bump Description A1 V CC Supply Voltage. Bypass to ground with a 1pF capacitor as close as possible to the IC. A2 RFOUT (SHDN) A2 B2 GND RF Output/SHDN Input. RFOUT is internally matched to 5I and pulled up to V CC through a 1MI resistor. SHDN is shared with the RFOUT bump. The devices are in active mode by default once V CC is applied. RFOUT(SHDN) can be pulled to a DC low externally to shut down the IC. B1 RFIN RF Input. Requires a DC-blocking capacitor and external matching components. B2 GND Ground. Connect to the PCB ground plane. / Detailed Description The / are LNAs designed for GPS L1, Galileo, and GLONASS applications. The devices feature an optional power-shutdown control mode to eliminate the need for an external supply switch. The devices achieve high gain, ultra-low-noise figure, and excellent linearity. Input and Output Matching The devices require an off-chip input matching. Only an inductor in series with a DC-blocking capacitor is needed to form the input matching circuit. The Typical Application Circuit shows the recommended inputmatching network. These values are optimized for the best simultaneous gain, noise figure, and return loss performance. The value of the input coupling capacitor affects IIP3. A smaller coupling capacitor results in lower IIP3. The devices integrate an on-chip output matching to 5I at the output, eliminating the need for external matching components. Tables 1 and 2 list typical device S parameters and Kf values. Typical noise parameters are shown in Tables 3 and 4. Shutdown The devices include an optional shutdown feature to turn off the entire chip. The devices are placed in active mode by default once VCC is applied, due to the on-chip pullup resistor to VCC at the RFOUT bump (shared with the SHDN input). To shut down the part, apply a logiclow to the RFOUT bump through an external resistor with an adequate value, e.g., 25kI, in order not to load the RF output signal during active operation. 5
/ Table 1. Typical S Parameter Values and K-Factor FREQ. (MHz) S11 S11 S21 S21 S12 S12 S22 S22 1-2.9-26.8 6.2-19. 3. 169. -1.4 7. 15.2 11-3.1-27.2 7.9-11. 3. 163. -2. -64. 17.4 12-3.4-27. 9.5-113. 2. 157. -2.9-73. 18. 13-3.5-28. 12.8-128. 8. -176. -7. -99. 4.6 14-3.5-28.3 12.8-128. 6. -164. -7. -99. 32.3 15-3.9-29. 13.9-144. -49. -166. -14.1-124. 16.3 1575-4.1-27. 14.1-156. -47. 164. -29. -113. 13.5 16-4.1-27.7 14.1-16. -48. 154. -21.2 68. 15. 17-4. -28.1 13.9-174. 4. 166. -9. 42. 26.4 18-4.2-28.9 12.9 17. -49. -16..3 26.4 13.6 19-4.4-29. 11.4 16. -47.3-176. -3.3 13.9 1.2 2-4.5-28.9 9.9 153. -46.5 17. -2.3 5. 8.5 Kf Table 2. Typical S Parameter Values and K-Factor FREQ. (MHz) S11 S11 S21 S21 S12 S12 S22 S22 1 - -18. 3.6-116. 4. 15. -1.3 3. 22.5 11-3.4-17.5 5.2-116.9 5. 147. -1.9-6.6 29.9 12-3.6-16.8 6.8-119. 6.6 147. -2.7-69.2 4.5 13-3.5-17.2 8.6-124. -63. -144. -4.2-8. 9.4 14-3.8-18. 1.1-137.5-49.8-145. -7.7-95. 23.7 15-4. -16.5 1.7-151. -47.3 174. -14.5-17.7 19.7 1575-4.1-15.8 11. -161.5-48.3 169. -35. 151. 22.4 16-4.1-15.7 11.1-164.9-48.7 159. -23.4 74.9 23.1 17-4.1-16.6 11. -179. 5. 175. -9.7 5. 43.1 18-4.2-16.7 1.2 165. -48. -151..2 34. 16.5 19-4.4-16.6 8.6 155. -46. -164. - 21. 11.9 2-4.5-16.3 7.2 149. -45.6-179. -2.3 12. Kf Table 3. Typical Noise Parameters (VCC = 2.85V, TA = +25NC) FREQUENCY (MHz) FMIN G OPT G OPT ANGLE R N (I) 155.63.43 45.7 8.25 156.63.43 46. 8.23 157.63.42 46.3 8.22 1575.63.42 46.4 8.22 158.63.42 46.5 8.21 159.63.42 46.8 8.2 16.64.42 47.1 8.19 6
Table 4. Typical Noise Parameters (VCC = 2.85V, TA = +25NC) FREQUENCY (MHz) FMIN G OPT G OPT ANGLE R N (I) 155.73.42 59. 8.34 156.74.42 59.4 8.31 157.74.42 59.7 8.29 1575.74.42 59.9 8.28 158.74.42 6.1 8.27 159.74.41 6.5 8.25 16.74.41 6.8 8.22 Applications Information A properly designed PCB is essential to any RF microwave circuit. Use controlled-impedance lines on all high-frequency inputs and outputs. Bypass VCC with decoupling capacitors located close to the device. For long VCC lines, it may be necessary to add decoupling capacitors. Locate these additional capacitors further away from the device package. Proper grounding of the GND pin is essential. If the PCB uses a topside RF ground, connect it directly to the GND pin. For a board where the ground is not on the component layer, connect the GND pin to the board with multiple vias close to the package. Refer to www.maxim-ic.com for the EV kit schematic, Gerber data, PADS layout file, and BOM information. PROCESS: SiGe BiCMOS Chip Information Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a +, #, or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 4 WLP W4A+1 21-48 / 7
/ REVISION NUMBER REVISION DATE DESCRIPTION Revision History PAGES CHANGED 8/1 Initial release Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 Maxim Integrated Products, 12 San Gabriel Drive, Sunnyvale, CA 9486 48-737-76 21 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.