19-1673; Rev 0a; 4/02 EVALUATION KIT MANUAL AVAILABLE 45MHz to 650MHz, Integrated IF General Description The are compact, high-performance intermediate-frequency (IF) voltage-controlled oscillators (VCOs) designed specifically for demanding portable wireless communication systems. They combine monolithic construction with low-noise, low-power operation in a tiny 6-pin SOT23 package. These low-noise VCOs feature an on-chip varactor and feedback capacitors that eliminate the need for external tuning elements, making the ideal for portable systems. Only an external inductor is required to set the oscillation frequency. In addition, an integrated differential output buffer is provided for driving a mixer or prescaler. The buffer output is capable of supplying up to -8dBm (differential) with a simple power match. It also provides isolation from load impedance variations. The operate from a single +2.7V to +5.5V supply and offer low current consumption. These IF oscillators can cover the 45MHz to 650MHz frequency range. Cellular and PCS Mobile Phones 2.4GHz ISM Band 902MHz to 928MHz ISM Band Land Mobile Radio GPS Receivers General-Purpose IF Oscillators PART FREQUENCY RANGE (MHz) SUPPLY CURRENT (ma) Applications Selector Guide PHASE NOISE (dbc/hz) 45 to 70 70 to 150 150 to 300 1.9 2.1 2.1-117 -112-107 300 to 500 2.7-100 500 to 650 3.6-93 Small Size Integrated Varactor for Tuning Low Phase Noise Wide Application Frequency Range Differential or Single-Ended Outputs Single +2.7V to +5.5V Supply Ultra-Small SOT23-6 Package On-Chip Temperature-Stable Bias Low-Current Operation PART EUT-T EUT-T EUT-T EUT-T EUT-T TOP VIEW IND GND Features Ordering Information TEMP. RANGE -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C OUT- PIN- PACKAGE 6 SOT23-6 6 SOT23-6 6 SOT23-6 6 SOT23-6 6 SOT23-6 Pin Configuration/ Functional Diagram 1 6 OUT+ 2 5 V CC TOP MARK AABB AABC AABD AABE AABF TUNE 3 4 SOT23-6 Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim s website at www.maxim-ic.com.
ABSOLUTE MAXIMUM RATINGS V CC to GND...-0.3V to +6V IND to GND...-0.6V to (V CC + 0.3V) TUNE to GND...-0.3V to (V CC + 0.3V) OUT+, OUT- to GND...-0.3V to (V CC + 0.6V) Continuous Power Dissipation (T A = +85 C) 6-Pin SOT23 (derate 8.7mW/ C above +70 C)...696mW Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS Operating Temperature Range...-40 C to +85 C Junction Temperature...+150 C Storage Temperature Range...-65 C to +150 C Lead Temperature (soldering, 10s)...+300 C (V CC = +2.7V to +5.5V, V TUNE = 0.4V to 2.4V, T A = -40 C to +85 C, unless otherwise noted. Typical values are at V CC = +2.75V, V TUNE = 1.5V, and.) (Note1) PARAMETER CONDITIONS MIN TYP MAX UNITS Supply Voltage 2.7 5.5 Supply Current (Note 2) T A = -40 C to +85 C T A = -40 C to +85 C T A = -40 C to +85 C T A = -40 C to +85 C T A = -40 C to +85 C 1.9 2.6 2.1 2.7 2.1 3.2 DC Output Current (Note 3) OUT+ plus OUT- 0.5 1.0 1.5 3.0 3.5 2.7 4.4 5.5 3.6 6.8 TUNE Input Current 0.03 na 2.8 7.5 V ma ma 2
AC ELECTRICAL CHARACTERISTICS ( EV kits, V CC = +2.7V to +5.5V, V TUNE = 0.4V to 2.4V, T A = -40 C to +85 C, unless otherwise noted. Typical values are at V CC = +2.75V, V TUNE = 1.5V, and.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS 45 70 70 150 Oscillator Nominal Frequency Range (Note 4) 150 300 MHz 300 500 500 650-4.1 +3.2 T A = -40 C to +85 C -2.25 +2.25-4.4 +3.4 T A = -40 C to +85 C -2.5 +2.5 Guaranteed Frequency Limits -4.6 +3.6 (relative to nominal) (Note 5) T A = -40 C to +85 C -2.75 +2.75 % -5.0 +3.8 T A = -40 C to +85 C -3.0 +3.0 Peak Tuning Gain V TUNE = 0.4V to 0.6V step (Note 6) 14.5 %/V Single-Ended Output Power (Note 7) -10 dbm Phase Noise (Note 8) f OFFSET = 100kHz T A = -40 C to +85 C, Q L 35, Q L 35, Q L 35, Q L 40, Q L 40-4.7 +3.6-2.8 +2.8-117 -112-107 dbc/hz -100-93 3
AC ELECTRICAL CHARACTERISTICS (continued) ( EV kits, V CC = +2.7V to +5.5V, V TUNE = 0.4V to 2.4V, T A = -40 C to +85 C, unless otherwise noted. Typical values are at V CC = +2.75V, V TUNE = 1.5V, and.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS Even-Order Harmonics Differential, R L = 50Ω each side -30 Supply Pushing (Note 9) Note 1: Production tested at. Maximum and minimum over temperature limits are guaranteed by design and characterization. Note 2: Supply current is measured while the part is oscillating and inductor Q Q MIN. For //, Q MIN = 35; for /, Q MIN = 40. Note 3: The DC output current is the total available output signal current. Note 4: Application range of the part is achieved using external inductance as specified in Figures 1-5 and shown in Figure 6. The internal varactors support center frequencies of 45MHz to 650MHz. The center frequency is defined by the value of the external inductor element, L F. The application frequency limits are guaranteed by design and characterization. Note 5: The guaranteed (tested) limits ƒ MIN and ƒ MAX are measured at V TUNE = 0.4V and V TUNE = 2.4V, respectively. Passing requirements are: ƒ ƒ MIN at V TUNE = 0.4 and ƒ ƒ MAX at V TUNE = 2.4V. The nominal frequency of oscillation is defined by the inductor. Note 6: Describes peak tuning gain, which occurs at V TUNE = 0.4V. Note 7: Measurement at OUT+ or OUT- matched for optimum power transfer into 50Ω load near the center of the operating frequency range. Note 8: The phase-noise specifications listed apply to the typical operating circuit shown in Figure 6. Apply over the entire operating frequency range of the. Note 9: Supply pushing is measured with V CC stepped from +2.7V to +3.2V. 60 120 220 480 720 dbc khz/v Typical Operating Characteristics (MAX260_ EV kit, V CC = +2.75V, V TUNE = 1.4V,, unless otherwise noted.) SUPPLY CURRENT (ma) 4.0 3.5 3.0 2.5 2.0 1.5 SUPPLY CURRENT vs. TEMPERATURE /9-01 LEAKAGE CURRENT (na) 0.10 0.08 0.06 0.04 0.02 TUNE INPUT LEAKAGE CURRENT vs. TEMPERATURE /9-02 FREQUENCY (MHz) 65 60 55 50 VCO TUNING CURVE /9-03 1.0-40 -20 0 20 40 60 80 TEMPERATURE ( C) 0-40 -20 0 20 40 60 80 TEMPERATURE ( C) 45 0 0.5 1.0 1.5 2.0 2.5 3.0 V TUNE (V) 4
Typical Operating Characteristics (continued) (MAX260_ EV kit, V CC = +2.75V, V TUNE = 1.4V,, unless otherwise noted.) FREQUENCY (MHz) 130 120 110 100 90 VCO TUNING CURVE 0 0.5 1.0 1.5 2.0 2.5 3.0 V TUNE (V) 680 640 /9-04 FREQUENCY (MHz) 260 240 220 200 180 160 VCO TUNING CURVE VCO TUNING CURVE 0 0.5 1.0 1.5 2.0 2.5 3.0 V TUNE (V) /9-07 0-10 /9-05 FREQUENCY (MHz) 430 400 370 340 310 OUTPUT SPECTRUM VCO TUNING CURVE 0 0.5 1.0 1.5 2.0 2.5 3.0 V TUNE (V) /9-08 /9-06 FREQUENCY (MHz) 600 560 (db) -20-30 520-40 480 0 0.5 1.0 1.5 2.0 2.5 3.0 V TUNE (V) -50 f o 2f o 3f o 4f o 5f o 6f o 7f o FREQUENCY Pin Description PIN NAME FUNCTION 1 IND Tuning Inductor Port. Connect an inductor from IND to GND to set VCO center frequency (see Oscillation Frequency). 2 GND Ground. Connect to the ground plane with a low-inductance path. 3 TUNE Voltage-Control Input for Frequency Tuning. Input voltage range from +0.4V to +2.4V. 4 OUT- High-Impedance Open-Collector Output. An external pull-up resistor or inductor to V CC is required. Output power is dependent on external load impedance. OUT- is complementary to OUT+. 5 V CC Supply Voltage Connection. Connect an external bypass capacitor to ground for low noise and low spurious-output content. See Layout Issues for more details. 6 OUT+ High-Impedance Open-Collector Output. An external pull-up resistor or inductor to V CC is required. Output power is dependent on external load impedance. OUT+ is complementary to OUT-. 5
Detailed Description The are low-noise VCOs designed for fixed/single-frequency IF applications. The core oscillator circuit is based on the well-known Colpitts topology. The varactor and feedback capacitors are integrated on-chip so that only an external inductor is required to establish the frequency of oscillation and produce a properly operating VCO. The tuning range, biasing, startup, etc., are all managed within the IC. This highly integrated design dramatically simplifies the parts application. The tuning range is wide enough so that, with the use of ±2% tolerance inductors, no board-level adjustments to the oscillation frequency are necessary. Once the correct inductor value is chosen, the VCO is guaranteed always to tune to the desired operating frequency. In addition, with the use of inductors of moderate Q (35 to 40), the VCO achieves excellent phase-noise performance. Applications Information Desired Oscillation Frequency The desired VCO operating frequency is set by the value of the external inductance, L F. Figures 1 5 show the inductance value L F required to achieve the desired oscillation frequency. The inductor value can be taken directly from these figures. Inductance must be selected accurately to ensure proper operation over all conditions. Inductor Implementation The inductance value required for the desired operating frequency may not necessarily coincide with a standard-value SMT inductor, which typically increases size in ~1.2x steps. In such cases, the inductance must be constructed from two inductors, L F1 and L F2, in order to achieve the desired inductance value. Choose L F1 to be a standard-value inductor with a value just less than that required for L F. Choose L F2 to be a standard-value inductor with a value just less than (L F - L F1 ). L F1 should adhere to the minimum Q requirements, but L F2 may be implemented as a lower-cost, lower-q, thin-film SMT inductor. Its lower Q has only a small impact on the overall Q of the total inductance because it is <20% of the total inductance. However, the overall Q of L F1 and L F2 must be greater than the minimum inductor Q (Table 1). It is also permissible to use PC board traces to provide a small amount of inductance, thereby adjusting the total inductance value. On the /, the inductance values for L F2 are sometimes more exactly implemented as a PC board trace (shorted to GND), rather than an SMT inductor. When designing L F with two inductors, use the simple model in Figure 7 to calculate X L and L EQ. The L F in Figures 1 5 represents an equivalent inductance as seen by pin 1 (IND). The equivalent inductance corresponds to the inductive reactance connected to IND at the desired oscillation frequency (f NOMINAL ). L EQ = X L / (2π f NOMINAL ) as seen in Figure 8 Design L EQ = L F at the desired f NOMINAL. The are designed to tolerate approximately 0.5pF of external parasitic capacitance at IND. This parasitic capacitance arises from the pad capacitance at the device pin and pads for the inductor. Additional shunt capacitance is not recommended because it degrades the tuning range. Bypass Capacitor on TUNE The s oscillator design uses a variant of the Colpitts topology, where DC bias for the varactor is applied via a DC voltage on TUNE and a ground connection through the external inductor L F. TUNE must also have a high-frequency AC ground for Table 1. External Inductor LF Range Table 2. CBYPASS Values PART FREQUENCY RANGE (MHz) INDUCTANCE RANGE (nh) MIN INDUCTOR Q DEVICE C BYPASS 45 to 70 70 to 150 150 to 300 35 35 35 300 to 500 680 L F 2200 150 L F 820 39 L F 180 10 L F 47 40 500 to 650 3.9 L F 15 40 820 pf 680 pf 330 pf 100 pf 39 pf 6
REQUIRED INDUCTANCE (nh) 1900 1800 1700 1600 1500 1400 1300 1200 1100 REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY MEASUREMENT CONDITIONS VCC = 2.75V, TA = 25 C, RLOAD = 100Ω 50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω, PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING CONDITIONS AND WORST-CASE COMPONENT VALUES (±2% INDUCTOR AND IC PROCESS VARIATION). EFFECTIVE INDUCTANCE FROM IND TO GND 1000 900 INDUCTOR VALUE MOUNTED ON EV KIT 800 700 45 47 49 51 53 55 57 59 61 63 65 67 69 DESIRED VCO FIXED FREQUENCY (MHz) Figure 1. Required Inductance vs. Desired VCO Fixed Frequency 7
REQUIRED INDUCTANCE (nh) 790 740 690 640 590 540 490 440 390 REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY MEASUREMENT CONDITIONS VCC = 2.75V, TA = 25 C, RLOAD = 100Ω 50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω, PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING CONDITIONS AND WORST-CASE COMPONENT VALUES (±2% INDUCTOR AND IC PROCESS VARIATION). EFFECTIVE INDUCTANCE FROM IND TO GND 340 290 INDUCTOR VALUE MOUNTED ON EV KIT 240 190 140 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 DESIRED VCO FIXED FREQUENCY (MHz) Figure 2. Required Inductance vs. Desired VCO Fixed Frequency 8
REQUIRED INDUCTANCE (nh) 170 160 150 140 130 120 110 100 90 REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY MEASUREMENT CONDITIONS VCC = 2.75V, TA = 25 C, RLOAD = 100Ω 50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω, PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING CONDITIONS AND WORST-CASE COMPONENT VALUES (±2% INDUCTOR AND IC PROCESS VARIATION). 80 EFFECTIVE INDUCTANCE FROM IND TO GND 70 60 INDUCTOR VALUE MOUNTED ON EV KIT 50 40 30 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 DESIRED VCO FIXED FREQUENCY (MHz) Figure 3. Required Inductance vs. Desired VCO Fixed Frequency 9
REQUIRED INDUCTANCE (nh) 41.0 40.0 38.0 37.0 36.0 35.0 34.0 33.0 32.0 31.0 30.0 29.0 28.0 27.0 26.0 25.0 24.0 23.0 22.0 21.0 20.0 19.0 18.0 17.0 16.0 15.0 14.0 13.0 12.0 11.0 REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY INDUCTOR VALUE MOUNTED ON EV KIT MEASUREMENT CONDITIONS VCC = 2.75V, TA = 25 C, RLOAD = 100Ω 50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω, PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING CONDITIONS AND WORST-CASE COMPONENT VALUES (±2% INDUCTOR AND IC PROCESS VARIATION). EFFECTIVE INDUCTANCE FROM IND TO GND 10.0 9.0 300 310 320 330 340 350 360 370 380 390 400 410 420 420 430 440 450 460 470 480 490 500 Figure 4. Required Inductance vs. Desired VCO Fixed Frequency 10
REQUIRED INDUCTANCE (nh) 14.0 13.5 13.0 12.5 12.0 11.5 11.0 10.5 10.0 9.5 9.0 8.5 8.0 7.5 REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY MEASUREMENT CONDITIONS VCC = 2.75V, TA = 25 C, RLOAD = 100Ω 50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω, PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING CONDITIONS AND WORST-CASE COMPONENT VALUES (±2% INDUCTOR AND IC PROCESS VARIATION). EFFECTIVE INDUCTANCE FROM IND TO GND 7.0 6.5 6.0 5.5 INDUCTOR VALUE MOUNTED ON EV KIT 5.0 4.5 4.0 3.5 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 DESIRED VCO FIXED FREQUENCY (MHz) Figure 5. Required Inductance vs. Desired VCO Fixed Frequency 11
the cathode of the varactor. This is accomplished through the use of a simple bypass capacitor connected from TUNE to ground. The value of this capacitor should be greater than or equal to the values listed in Table 2. This capacitor provides an AC short to ground for the internal node of the varactor. It is acceptable to select the next-largest standard-value capacitor. Use a capacitor with a low-loss dielectric such as NPO; X7Rbased capacitors are not suitable. Omitting this capacitor would affect the tuning characteristics of the. Proper operation of the VCOs requires the use of this bypass capacitor. The VCO is designed to tune over the full tuning range with a voltage range of 0.4V to 2.4V applied to TUNE. This voltage typically originates from the output of the phase-locked (PLL) loop filter. Output Interface The VCO includes a differential output amplifier after the oscillator core. The amplifier stage provides valuable isolation and offers a flexible interface to the IF stages, such as a mixer and PLL prescaler. The output can be taken single ended or differentially; however, the maximum output power and lowest harmonic output are achieved in the differential output mode. Both outputs (OUT- and OUT+) are open-collector types and require a pull-up element to V CC ; this can be either resistive or inductive. A resistor pull-up is the most straightforward method of interfacing to the output, and works well in applications that operate at lower frequencies or only require a modest voltage swing. In Figure 6, Z1 and Z2 are 1kΩ pull-up resistors that are connected from OUT+ and OUT- to V CC, respectively. These resistors provide DC bias for the output amplifier and are the maximum value permitted with compliance to the output voltage swing limits. In addition, the 1kΩ resistors maximize the swing at the load. DC-blocking capacitors are connected from OUT- and OUT+ to the load. If the load driven is primarily resistive and the VCO operating frequency is below the -3dB bandwidth of the output network, then the peak-to-peak differential signal amplitude is approximately: V diff 2 1mA 1k R LOAD OUTp p ( ) = Ω 1k Ω + R LOAD To optimize the output voltage swing or the output power, use a reactive power match. The matching network is a simple shunt-inductor series-capacitor circuit, as shown in Figure 6. The inductors are connected from OUT- and OUT+ (in place of resistors) to V CC to provide DC bias for the output stage. The series capacitors are connected from OUT- and OUT+ to the load. The values for L MATCH (Z 1 and Z 2 ) and C MATCH (C 1 and C 2 ) are chosen according to the operating frequency and load impedance. As the output stage is essentially a high-speed current switch, traditional linear impedance using techniques with [S] parameters do not apply. To achieve a reactive power match, start with the component values provided in the EV kit, and adjust values experimentally. In general, the differential output may be applied in any manner, as would conventional differential outputs. The only constraints are the need for a pull-up element to V CC and a voltage swing limit at the output pins OUTand OUT+. Layout Considerations In general, a properly designed PC board is essential to any RF/microwave circuit or system. Always use controlled impedance lines (microstrip, coplanar waveguide, etc.) on high-frequency signals. Always place decoupling capacitors as close to the V CC pin as possible. For low phase noise and spurious content, use an appropriate size decoupling capacitor. For long V CC lines, it may be necessary to add additional decoupling capacitors located further from the device. Always provide a low-inductance path to ground. Keep the GND vias as close to the device as possible. In addition, the VCO should be placed as far away from the noisy section of a larger system, such as a switching regulator or digital circuits. Use star topology to separate the ground returns. The resonator tank circuit (L F ) is critical in determining the VCO s performance. For best performance, use high-q components and choose values carefully. To minimize the effects of parasitic elements, which degrade circuit performance, place L F and C BYP close to their respective pins. Specifically, place C BYP directly across pins 2 (GND) and 3 (TUNE). For the higher frequency versions, consider the extra parasitic inductance and capacitance when determining the oscillation frequency. Be sure to account for the following: PC board pad capacitance at IND, PC board pad capacitance at the junction of two series inductors, series inductance of any PC board traces, and the inductance in the ground return path from the grounded side of the inductor and IC s GND pin. For best results, connect the ground side to the tuning inductor as close to pin 2 as possible. In addition, remove the ground plane around and under L F and C BYP to minimize the effects of parasitic capacitance. 12
TUNE L F C BYP FROM PLL LOOP FILTER OUTPUT Figure 6. Typical Operating Circuit 1 6 OUT+ 2 5 V CC 3 4 OUT- V CC Z1 Z2 C1 C3 C2 R LOAD R LOAD TRANSISTOR COUNT: 158 Chip Information 13
C PAR2 L F2 L F1 IND 1 CPAR1 Figure 7. Simple Model of External Inductance L EQ = X L / 2π ƒ NOMINAL X L IND 1 Figure 8. Inductive Reactance at Pin 1 (IND) V CC 4 Γ Z L Figure 9. Output Matching Network 14
Package Information 6LSOT.EPS Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 15 2002 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.