MODE: M5CTC Super-mini Termina Boc Signa Conditioners M5-UNIT CT TRANSMITTER (camp-on current sensor) Functions & Features Converts an aternating current into a standard process signa Easy-to-insta camp-on type current sensor without needing a current transformer Camp-on current sensor incuded Wide input range from 10 A up to 600 A True RMS sensing High-density mounting Power ED Typica Appications Centraized monitoring and contro of motors at a supervisory pane Monitoring abnorma oad current at motors to detect pump mafunctions 25 (.98) 97 (3.82) 50: 0 50 A AC 60: 0 60 A AC 75: 0 75 A AC 100: 0 100 A AC 125: 0 125 A AC 150: 0 150 A AC 175: 0 175 A AC 200: 0 200 A AC 225: 0 225 A AC 250: 0 250 A AC 300: 0 300 A AC 350: 0 350 A AC 00: 0 00 A AC 500: 0 500 A AC 600: 0 600 A AC (Not seectabe with the sensor type code 1 'eadwire type CSA') [3] OUTPUT Current A: 20 ma DC (oad resistance 550 Ω max.) Z: Specify current (See OUTPUT SPECIFICATIONS) Votage : 0 10 V DC (oad resistance 1000 Ω min.) 5: 0 5 V DC (oad resistance 500 Ω min.) 6: 1 5 V DC (oad resistance 500 Ω min.) W: -10 +10 V DC (oad resistance 8000 Ω min.) 5W: -5 +5 V DC (oad resistance 000 Ω min.) 0: Specify votage (See OUTPUT SPECIFICATIONS) 1 (1.61) mm (inch) MODE: M5CTC [1][2][3] [][5] ORDERING INFORMATION Specify a code from beow for each [1] through [5]. Code number: M5CTC-[1][2][3]-[][5] (e.g. M5CTC-150A-R/Q) Specify variabes. Specia output range (For codes Z & 0) [1] SENSOR 1: eadwire type CSA 2: Screw termina type CSB [2] INPUT 10: 0 10 A AC 15: 0 15 A AC 20: 0 20 A AC 30: 0 30 A AC 0: 0 0 A AC [] POWER INPUT AC Power M: 85 26 V AC (Operationa votage range 85 26 V, 7 66 Hz) DC Power R: 2 V DC (Operationa votage range 2 V ±10 %, rippe 10 %p-p max.) [5] OPTIONS ban: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detai, refer to M-System's web site.) /C01: Siicone coating /C02: Poyurethane coating /C03: Rubber coating ACCESSORIES The camp-on current sensor is incuded in the product pacage. Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
MODE: M5CTC CAMP-ON CURRENT SENSOR (eadwire type CSA) 0 10 A through 0 75 A Use Sensor mode No.: CSA-08 Sensor cabe mode No.: CSA-08C-30 Appicabe cabe diameter: Max. 10.0 Sensor eadwire: AWG 22 Weight: 5 g (1.6 oz) 0 100 A Use Sensor mode No.: CSA-12 Sensor cabe mode No.: CSA-08C-30 Appicabe cabe diameter: Max. 16.0 Sensor eadwire: AWG 22 Weight: 70 g (2.5 oz) 0 125 A through 0 300 A Use Sensor mode No.: CSA-30 Appicabe cabe diameter: Max. 2.0 Sensor eadwire: AWG 18, 200 mm Weight: 200 g (7.1 oz) 0 350 A through 0 500 A Use Sensor mode No.: CSA-50 Appicabe cabe diameter: Max. 36.0 Sensor eadwire: AWG 18, 200 mm Weight: 300 g (10.6 oz) CAMP-ON CURRENT SENSOR (screw termina type CSB) Connection: M3 screw termina (torque 0.5 N m) Screw termina: Nice-pated stee Output wiring: Use AWG22 or thicer wires for the output. Twist the paired wires, extendabe up to 30 meters. 0 10 A through 0 50 A Use Sensor mode No.: CSB-05 Appicabe cabe diameter: Max. 10.0 Weight: 5 g (1.6 oz) 0 60 A through 0 100 A Use Sensor mode No.: CSB-10 Appicabe cabe diameter: Max. 16.0 Weight: 80 g (2.8 oz) 0 125 A through 0 200 A Use Sensor mode No.: CSB-20 Appicabe cabe diameter: Max. 2.0 Weight: 200 g (7.1 oz) 0 225 A through 0 00 A Use Sensor mode No.: CSB-0 Appicabe cabe diameter: Max. 35.0 Weight: 300 g (10.6 oz) 0 500 A through 0 600 A Use Sensor mode No.: CSB-60 Appicabe cabe diameter: Max. 35.0 Weight: 360 g (12.7 oz) Note 1: The output vaues may vary depending on the accuracy of engagement at the camp connection. Note 2: The sensor is detachabe up to 100 times (approx.). Note 3: The sensor s mechanica construction may cause it to generate resonance sound. However, it does not affect the performance of the sensor. GENERA SPECIFICATIONS Construction: Termina boc Connection: M3.5 screw terminas (torque 0.8 N m) Screw termina: Nice-pated stee Housing materia: Fame-resistant resin (bac) Isoation: Sensor core to input or output to power Input waveform RMS sensing: Up to 15 % of 3rd harmonic content Zero adjustment: -2 to +2 % (front) Span adjustment: 98 to 102 % (front) Power ED: Green ight turns on when the power is suppied. INPUT SPECIFICATIONS Frequency: 50 / 60 Hz Overoad capacity CSA - 08: 120 A continuous CSA - 12: 300 A continuous CSA - 30: 360 A continuous CSA - 50: 600 A continuous CSB - 05: 100 A continuous CSB - 10: 200 A continuous CSB - 20: 300 A continuous CSB - 0: 600 A continuous CSB - 60: 720 A continuous Operationa range: 5 120 % of rating Be sure that the input votage is of 0 V or ess. OUTPUT SPECIFICATIONS DC Current: 0 20 ma DC Minimum span: 1 ma Offset: Max. 1.5 times span oad resistance: Output drive 11 V max. DC Votage: 0 10 V DC Minimum span: 1 V Offset: Max. 1.5 times span oad resistance: Output drive 10 ma max.; at 1 V INSTAATION Power Consumption AC: Approx. 2 VA at 100 V Approx. 3 VA at 200 V Approx. 3 VA at 26 V DC: Approx. 2 W Operating temperature: -5 to +55 C (23 to 131 F) Operating humidity: 0 to 90 %RH (non-condensing) Mounting: DIN rai Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
MODE: M5CTC Weight: 80 g (2.8 oz) PERFORMANCE in percentage of span Accuracy: ±0.5 % with input 5 100 % (Input 10 100 % for the output codes W and 5W) Temp. coefficient: ±0.015 %/ C (±0.008 %/ F) Response time: 0.5 sec. (0 90 %) Rippe: 0.5 %p-p max. ine votage effect: ±0.1 % over votage range Insuation resistance: 100 MΩ with 500 V DC Dieectric strength DC powered: 2000 V AC @1 minute (input or output to power to ground) 1000 V AC @1 minute (sensor core to sensor output) AC powered: 1500 V AC @1 minute (input or output to power to ground) 1000 V AC @1 minute (sensor core to sensor output) FRONT VIEW 1 2 3 Power ED Span Adj. Zero Adj. 5 6 7 8 DIMENSIONS unit: mm (inch) 7.3 (.29) 8 M3.5 SCREW 1 2 3 DIN RAI 35mm wide 9 (3.70) 35. (1.39) 5 6 7 8 3 (.12) 25 (.98) 1 (1.61) [3.3 (.13)] When mounting, no extra space is needed between units. Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
MODE: M5CTC Sensor mode No.: CSA-08 Sensor mode No.: CSB-10 26 (1.02) 10 (.39) 1 (1.61) 27 (1.05) 150 (5.91) 3000 (118) 7.5 (.30) 30.5 (1.20) 7.5 (.30) 53.7 (2.11) 16 (.63) 23 (.91) Sensor mode No.: CSA-12 37. (1.7) TERMINA COVER (detachabe) 29 (1.1) 31 (1.22) 16 (.63).5 (1.75) 30 (1.18) Sensor mode No.: CSA-30 7.5 (1.87) 3 (1.3) 2 (.9) Sensor mode No.: CSA-50 59.5 (2.3) 36 (1.1) 38 (1.50) Sensor mode No.: CSB-05 8.6 (.3) 26.3 (1.0) 8.6 (.3) 8 (1.89) 150 (5.91) 6 (2.52) 80 (3.15) 10 (.39) 0 (1.57) 50 (1.97) 200 (7.87) 3000 (118) 200 (7.87) Sensor mode No.: CSB-20 55.9 (2.20) 8.3 (.33) 35.9 (1.1) 8.3 (.33) Sensor mode No.: CSB-0 73.5 (2.89) 35.5 (1.0) Sensor mode No.: CSB-60 73.5 (2.89) 35.5 (1.0) 75.7 (2.98) 2 (.9) 93 (3.66) 35 (1.38) 93 (3.66) 35 (1.38) TERMINA COVER (detachabe) TERMINA COVER (detachabe) TERMINA COVER (detachabe) 28.9 (1.1) TERMINA COVER (detachabe) Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
MODE: M5CTC SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM SOURCE CONNECTOR* CAMP-ON SENSOR (A) (±) 3 ow Drift Ampifier Z S RMS Operation Output Driver POWER ED 5 6 + OUTPUT OAD 1 2 7 U(+) 8 V( ) POWER *Connector provided ony for the CSA-08 and CSA-12. Specifications are subject to change without notice. Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
INSTRUCTION MANUA CT TRANSMITTER (camp-on current sensor) MODE M5CTC M5CTC BEFORE USE... Than you for choosing M-System. Before use, pease chec contents of the pacage you received as outined beow. If you have any probems or questions with the product, pease contact M-System s Saes Office or representatives. PACAGE INCUDES: Signa conditioner... (1) Sensor... (1) Cabe (CSA-08, -12 ony)... (1) MODE NO. Confirm Mode No. maring on the product to be exacty what you ordered. INSTRUCTION MANUA This manua describes necessary points of caution when you use this product, incuding instaation, connection and basic maintenance procedures. POINTS OF CAUTION POWER INPUT RATING & OPERATIONA RANGE ocate the power input rating mared on the product and confirm its operationa range as indicated beow: 85 26V AC rating: 85 26V, 7 66 Hz, approx. 2 3VA 2V DC rating: 2V ±10%, approx. 2W GENERA PRECAUTIONS Before you remove the unit or mount it, turn off the power suppy and input signa for safety. ENVIRONMENT Indoor use When heavy dust or meta partices are present in the air, insta the unit inside proper housing with sufficient ventiation. Do not insta the unit where it is subjected to continuous vibration. Do not subject the unit to physica impact. Environmenta temperature must be within -5 to +55 C (23 to 131 F) with reative humidity within 0 to 90% RH in order to ensure adequate ife span and operation. WIRING Do not insta cabes (power suppy, input and output) cose to noise sources (reay drive cabe, high frequency ine, etc.). Do not bind these cabes together with those in which noises are present. Do not insta them in the same duct. Insta ightning surge protectors for those wires connected to remote ocations. For 2V DC power suppy ine, choose a surge protector with its maximum surge votage 0V or ess between ines. Recommended M-System mode: MDP-D2. AND... The unit is designed to function as soon as power is suppied, however, a warm up for 10 minutes is required for satisfying compete performance described in the data sheet. COMPONENT IDENTIFICATION Body Spec. Maring INSTAATION Set the unit so that its DIN rai adapter is at the bottom. MOUNTING THE UNIT ON A DIN RAI A) Hang the upper hoo at the rear side of unit on the DIN rai. B) Push in the ower in eeping pressing the unit to the DIN rai. A Termina Cover Power ED Span Adj. Zero Adj. REMOVING THE UNIT A) Push down the DIN rai adaptor using a minus screwdriver. B) Pu out the ower part of the unit. C) Remove the upper part from the DIN rai. C Spring oaded DIN Rai Adaptor CAMP-ON CURRENT SENSOR Secure the sensor to the cabe e.g. using tie wraps. Over-votage camp eement is incorporated for safety in open circuit. A B B DIN Rai EM-286 Rev.3 P. / Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
M5CTC TERMINA CONNECTIONS Connect the unit as in the diagram beow or refer to the connection diagram on the front of the unit. EXTERNA DIMENSIONS unit: mm (inch) 7.3 (.29) 8 M3.5 SCREW 1 2 3 DIN RAI 35mm wide 9 (3.70) 35. (1.39) 5 6 7 8 3 (.12) 25 (.98) 1 (1.61) [3.3 (.13)] When mounting, no extra space is needed between units. CAMP-ON CURRENT SENSOR (eadwire type CSA) 0 10A through 0 75A Use Sensor mode No.: CSA-08 Sensor cabe mode No.: CSA-08C-30 Appicabe cabe diameter: Max. 10.0 Sensor eadwire: AWG 22 Weight: 5 g (1.6 oz) 26 (1.02) 10 (.39) 1 (1.61) 27 (1.05) 150 (5.91) 3000 (118) 0 125A through 0 300A Use Sensor mode No.: CSA-30 Appicabe cabe diameter: Max. 2.0 Sensor eadwire: AWG 18, 200 mm Weight: 200 g (7.1 oz) 3 (1.3) 2 (.9) 6 (2.52) 0 (1.57) 200 (7.87) 23 (.91) 7.5 (1.87) 0 100A Use Sensor mode No.: CSA-12 Sensor cabe mode No.: CSA-08C-30 Appicabe cabe diameter: Max. 16.0 Sensor eadwire: AWG 22 Weight: 70 g (2.5 oz) 29 (1.1) 31 (1.22) 16 (.63).5 (1.75) 30 (1.18) 150 (5.91) 3000 (118) 0 350A through 0 500A Use Sensor mode No.: CSA-50 Appicabe cabe diameter: Max. 36.0 Sensor eadwire: AWG 18, 200 mm Weight: 300 g (10.6 oz) 59.5 (2.3) 36 (1.1) 38 (1.50) 80 (3.15) 50 (1.97) 200 (7.87) EM-286 Rev.3 P. 2 / Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
CAMP-ON CURRENT SENSOR (screw termina type CSB) Connection: M3 screw termina (nice-pated stee; torque 0.5 N m) 0 10A through 0 50A Use Sensor mode No.: CSB-05 Appicabe cabe diameter: Max. 10.0 Weight: 5 g (1.6 oz) 8.6 (.3) 26.3 (1.0) 8.6 (.3) 8 (1.89) 10 (.39) 0 500A through 0 600A Use Sensor mode No.: CSB-60 Appicabe cabe diameter: Max. 35.0 Weight: 360 g (12.7 oz) 73.5 (2.89) 35.5 (1.0) 93 (3.66) 35 (1.38) M5CTC 28.9 (1.1) 0 60A through 0 100A Use Sensor mode No.: CSB-10 Appicabe cabe diameter: Max. 16.0 Weight: 80 g (2.8 oz) 7.5 (.30) 30.5 (1.20) 7.5 (.30) 53.7 (2.11) 16 (.63) TERMINA COVER (detachabe) Note 1: The output vaues may vary depending on the accuracy of engagement at the camp connection. Note 2: The sensor is detachabe up to 100 times (approx.). Note 3: The sensor s mechanica construction may cause it to generate resonance sound. However, it does not affect the performance of the sensor. CONNECTION DIAGRAM SOURCE TERMINA COVER (detachabe) 37. (1.7) 0 125A through 0 200A Use Sensor mode No.: CSB-20 Appicabe cabe diameter: Max. 2.0 Weight: 200 g (7.1 oz) TERMINA COVER (detachabe) CONNECTOR* 3 5 + OUTPUT CAMP-ON SENSOR (A) (±) 6 7 U(+) OAD POWER 8 V( ) *Connector provided ony for the CSA-08 and CSA-12. 8.3 (.33) 35.9 (1.1) 8.3 (.33) 75.7 (2.98) 2 (.9) 55.9 (2.20) TERMINA COVER (detachabe) 0 225A through 0 00A Use Sensor mode No.: CSB-0 Appicabe cabe diameter: Max. 35.0 Weight: 300 g (10.6 oz) 35.5 (1.0) 93 (3.66) 35 (1.38) 73.5 (2.89) TERMINA COVER (detachabe) EM-286 Rev.3 P. 3 / Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com
M5CTC CHECING 1) Termina wiring: Chec that a cabes are correcty connected according to the connection diagram. 2) Power input votage: Chec votage across the termina 7 8 with a mutimeter. 3) Input: Chec that the input signa is within 5 120% of the fu-scae. ) Output: Chec that the oad resistance meets the described specifications. ADJUSTMENT PROCEDURE This unit is caibrated at the factory to meet the ordered specifications, therefore you usuay do not need any caibration. For matching the signa to a receiving instrument or in case of reguar caibration, adjust the output as expained in the foowing. HOW TO CAIBRATE THE OUTPUT SIGNA Use a signa source and measuring instruments of sufficient accuracy eve. Turn the power suppy on and warm up for more than 10 minutes. 1) ZERO: Appy 10% input and adjust output to 10%. 2) SPAN: Appy 100% input and adjust output to 100%. 3) Chec ZERO adjustment again with 10% input. ) When ZERO vaue is changed, repeat the above procedure 1) 3). MAINTENANCE Reguar caibration procedure is expained beow: CAIBRATION Warm up the unit for at east 10 minutes. Appy 10%, 25%, 50%, 75% and 100% input signa. Chec that the output signa for the respective input signa remains within accuracy described in the data sheet. When the output is out of toerance, recaibrate the unit according to the ADJUST- MENT PROCEDURE expained earier. M-SYSTEM WARRANTY M-System warrants such new M-System product which it manufactures to be free from defects in materias and wormanship during the 36-month period foowing the date that such product was originay purchased if such product has been used under norma operating conditions and propery maintained, M-System s soe iabiity, and purchaser s excusive remedies, under this warranty are, at M-System s option, the repair, repacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To submit a caim under this warranty, the purchaser must return, at its expense, the defective M-System product to the beow address together with a copy of its origina saes invoice. THIS IS THE ONY WARRANTY APPICABE TO M-SYSTEM PRODUCT AND IS IN IEU OF A OTHER WARRANTIES, EXPRESS OR IMPIED, INCUDING ANY IMPIED WARRANTIES OF MERCHANTABIITY OR FITNESS FOR A PARTICU- AR PURPOSE. M-SYSTEM SHA HAVE NO IABIITY FOR CONSEQUENTIA, INCIDENTA OR SPECIA DAMAGES OF ANY IND WHATSOEVER. M-System Co., td., 5-2-55, Minamitsumori, Nishinari-u, Osaa 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mai: info@m-system.co.jp EM-286 Rev.3 P. / Produte, Support und Service Rugghözi 2 CH - 553 Bussingen Te. +1 (0)56 222 38 18 maibox@sentronic.com