9 Fix the aluminum bracket on the fuselage with screw. 95 The floats installation finished. Screw (x5mm) 9 Blind Nut (mm) 9 Washer (xmm) 9 Screw (x5mm) Beaver Damped nut (mm) Washer (xmm) Screw (x5mm) Screw(x5mm) Washer (xmm) Damped nut (mm) 9 Drill holes to the relevant position in the floats as below. 9 Fix the floats to the fuselage.find the centre of the gravity. Aluminum parts Aluminum parts Centre line.mm 95mm 9 mm 5mm 55mm Washer (xmm) TP Screw (x0mm ) TP Screw (x0mm ) 5mm Fix the aluminum bracket to the floats. Centre line 97 The front view of the beaver with floats. Specification: Length :550 mm(") Wing Span : mm(95") Wing Area :0. sq. dm.9 sq. ft Beaver seaplane wing loading :. g/sq. dm 7. oz/sq. ft Beaver wing loading : g/sq. dm. oz/sq. ft Beaver seaplane flying weight :.7 kg(9. lbs) Beaver flying weight :7.kg(.7 lbs) Radio :ch& servos Engine :0 -cycle 0 -cycle INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
Assemble the floats 9 Mounting the seal cover. (with servos), Thank you for purchasing ESM'S products. When we designed this model we have fore considered some of our customers who loves fly it with floats. So we have provided floats as Optional parts. Please be kind to find the floats installation diagram below..5mm channel radio for aiplane is highly recommended for this model. Seal cover TP Screw (.xmm) 0 90 Please notice the specification of the aluminum brachets before install them to fuselage. Spinner nut : -cycle.0 "x7 Seal cover TP Screw (.xmm) Washer (xmm) Damped nut (mm) Blind Nut (mm) TP Screw (x0mm ) Screw (x5mm) Screw (x5mm) Sponge sheet Aluminum parts Aluminum parts 0 5 0 9 Damped nut (mm) Washer (xmm) Screw (x5mm) A B C 50mm mm 7mm Put sponge sheet at appropriate position before install the seal cover. 9 Drill holes to the revelant position in the fuselage as below. A.mm Screw (x5mm) Washer (xmm) Aluminum struts Fuselag Blind Nut (mm) B Sponge sheet C Warning Remove the covering with proper pressure to cut through only the covering itself.otherwise, cutting down into the balsa structure may weaken the model part and cause accident. Pre-cover the covering with clean cloth! Start at low setting. Increase the setting if necessary.if it is too high,you may damage the film. The pre-covered film on ARF kits may wrinkle due to variations of temperature.smooth out as explained right. with cover(cloth) Iow setting 7
Adjustment. Centre of Gravity. Assemble the aileron to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely. RUDDER Top view 0mm 0mm Side View 5mm Rod (x00mm) TP Screw (.xmm) Screw (x0mm) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(x5mm) Lock Nut (mm ) Washer(x5mm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 5 Adjustment. The full model side view when install completion. Apply instant type CA glue to aileron and pin hinges. Install the servo as the illustration below Pin hinge(xmm) AILERON 5mm 5mm FLAP 0mm AILERON FLAP Make sure hinges are mounted in the same line. 7 The model build finished. Keep some space about mm width between aileron and trailing edge. 5 Install the nylon control horn and connect the linkage. Trailing edge Rod (x00mm) Aileron mm Screw (x0mm) Make sure they are in the right position while installing.
The position of the control horn in the aileron. Apply instant type CA glue to flap and pin hinges. 77 Trim the shaded portion from the bottom of the top hatch as below. 0 Epoxy the wooden block to appropriate position in the fuselage as below. 5mm 0mm mm 00mm mm 0mm 0mm mm 5mm Pin hinge (x0xmm) 7 Secure the servo.install the nylon control horn and connect the linkage. 9 Keep some space about mm width between trailing edge and flap. 7 Drill holes to appropriate position in the hateh and epoxy the metal dowel in them. Drill holes to relcvant position in the fuselage for mounting the top hatch. TP Screw (.xmm) Trailing edge Magnet (0x0xmm).5mm Rod (x00mm) Flap 00mm mm 0mm mm mm Screw (x0mm) Lock Nut (mm ) Washer(x5mm) mm Washer Screw (x5mm) Make sure they are in the right position while installing. Magnet (0x0xmm) Matal douel (x0mm) 0 Assemble the flap to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely. 79 Epoxy the magnet to the wooden block as bslow. Adjustment. Rod (x00mm) TP Screw (.xmm) Screw (x0mm) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(x0xmm) Washer(x5mm) Lock Nut (mm ) Washer(x5mm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Magnet (0x0xmm) Magnet (0x0xmm) Wooden block(mm) ELEVATOR Side View 5mm 5mm Top view Position for right diagram. 5
7 Drill holes to relevant position in the main wing and epoxy nut in them. 7 Install the servo of rudder. Install the servo as the illustration below. Secure the servo.install the nylon control horn and connect the linkage. Set screw (xmm).5mm TP Screw (.xmm) Nut (mm).mm mm Washer (mm) Washer (mm) Linkage Stopper Washer (mm) Nut (mm) Set screw (xmm) mm Rod (x00mm) Screw (x0mm) Lock Nut (mm ) Washer(x5mm) Washer Screw (x5mm) 7 Assemble the wing strut with screw. 7 The servos installation finished sketch map. Install the nylon control horn and connect the linkage. Elevator servo Rod (x00mm) Hook(x50mm) Wood dowel (x50mm) Screw (x0mm) Rib template (mm ply) Hook screw Screw (x0mm) Rudder servo Rubber band Main wing joiner (5x70mm) 75 Mounting of the receiver and the battery. The position of the control horn in the flap. 5 The standard sketch map of the wings installation finished. A A" Magnet (0x0xmm) Matal douel (x0mm) A = A" B = B" Wooden block(mm) mm Linkage Stopper B B"
Set the rib templates to the appropriate position and drill holes. 9 Fix oneside of the main wing to the fuselage and take out the rubber bands with tool. Cut away the surplus parts of PVCpart carefully along the shade line. mm mm Ply (5x5xmm) Blind Nut (mm) Screw (x0mm) Nut (mm) TP Screw (.xmm) Rib template (mm ply) Hook(x50mm) Hook 7 Epoxy the wood dowels into the holes and set the hook screw with rubber band to the appropriate position into the main wing as below. 0 Fix the other side of the wing to the fuselage steadily. Fix the PVC on the fuselage with TP screw. 9 Assemble the PVC parts to the appropriate position as below. Wood dowel (x50mm) Hook screw Rubber band TP Screw (.xmm) TP Screw (.xmm).5mm 5mm.5mm.5mm TP Screw (.xmm) TP Screw (.xmm) Set the rib templates to the appropriate position on the fuselage and drill holes as below. 7 Epoxy the wheel pants to the main landing gear steadily. Keep some spacc between the fuselage and the wheel pants. 70 Drill holes to approprite position in fuselage and set the blind nut in them. mm mm Rib template Rib template (mm (mm ply) Stab joiner (x7mm) Pin hinge(xmm) U-style wire (x50mm) Tail landing gear(mm) Wooden dowel (x0mm) Rib template (mm ply) Tail landing gear(mm) Steering fullarm Tail wheel (5mm) Pin hinge(.5xmm) Collar (mm) Wooden Block (0x0xmm) Nose arm (mm) Ply (X5Xmm) Washer (xmm) TP Screw(x0mm) Screw (x0mm) Nut (mm ) Copper ball (mm ) Wooden Block 9mm.mm Blind Nut Ply (5x5xmm) Blind Nut (mm) Marked
0 Trim the cowling for engine and muffler and decoration. Epoxy the decoration part in the slot. Assemble the tail wheel steering mounts. Assemble the ball joint to the metal arms. Collar Ply (mm) 0 o Ply (mm).mm Collar Screw (x0mm) Screw (x0mm) Copper ball (mm ) Copper ball (mm )Nut (mm ) Trim the shaded portion for assembling the decoration part in step. Ply (X5Xmm) Washer (xmm) TP Screw(x0mm) Nut (mm ) Rod (x00mm) Metal arms Screw (x0mm) Nut (mm ) Copper ball (mm ) Epoxy the formet to appropriate pesition in the cowling. Cut away the surplus parts of canopy carefully along the shade line. Assemble the tail landing gear 5 Epoxy a wooden block at appropriate position in fuselage, and drill ahole in the centre. 00mm 7.5mm Former(mm) Collar Tail landing gear Metal arms Collar Assemble the cowling to fuselage with screw. 5 Epoxy the canopy to the fuselage. Trim a hole at the relevant position in the taill of fuselage as below. Drill holes to appropriate position in the rudder and epoxy the pin hinge to them. Sticker x5mm.5mm Pin hinge mm Make sure hinges are mounted in the same line. mm TP Screw (.xmm).mm mm Trim a hole and slot for the bend wire. Washer (xmm) TP Screw(x0mm) mm 5
7 Keep some space with mm width between the tailing edge and rudder. 0 Keep some space with about mm width between tailing edge and elevator. 55 Put the elevator rod through the tude in the fuselage as below. 5 Connect the elevator rod and the arm of elevator as below. Tailing edge Rudder Cut away the rubber tube when the epoxy glue dried. Tailing edge Elveator Rod (.x00mm) Rod (.x00mm) mm mm Make sure they are in the right position while installing. Make sure they are in the right position while installing. Rod (.x00mm) Epoxy the rudder to the vertical tail edge. A ccording to thr rib template drill holes to the tail of fuselage as below. 5 Epoxy a ply to the right place. 59 Drill holes to appropriate positirn and assemble the tail landing gear cover with screw..5mm.5mm Notice the hole position for thr bend wire. mm mm 0mm.5mm Rib template (mm ply) Ply(mm) TP Screw (.xmm) Ply (5x5xmm) 9 Apply instant type CA glue to elevator and pin hinge. Set the U-style wire through the tail of fuselage as below. 57 Put the elevator rod through the hole as below. Pin hinge(xmm) mm U-style wire Trim the shaded section Metal arms Nut (mm ) Copper ball Make sure hinges are mounted in the same line. mm Screw (x0mm) Screw (x0mm) Nut (mm ) Copper ball (mm ) TP Screw (x0mm) Washer (xmm) Ply (5x5xmm) Former(mm) Sticker 5
5 Put the rudder rod through the tude in the fuselage as below. Epoxy the wooden block to appropriate position of the stabilizer.this step only for beaner with float. Glue the elevator to the stabilizer by CA and epoxy. Rod (x00mm) Ply (5x5xmm) TP Screw (.xmm) Rod (.x00mm) Pyl(mm) Rod (.x00mm) mm Rod (.x00mm) Wooden Block Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 50 The sketch map of connecting the rod and arms. 5 Put the rudder rod through the hole as below. Drill two holes at the stabilizer root base on rib template and epexy the metal dowel in them. 7 The horizontal installation finished standard sketch map. Rod (x00mm) mm Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flihts, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. A A" Rod (x00mm) A = A" B = B" Wood dowel (x0mm) B B" 5 Connect the tail landing gear horn and the rudder horn as step 50. 5 Connect the rudder rod and the arm of rudder as below. 5 Drill holes to appropriate position in the stabilizer and epoxy it to the fuselahe as below. Rod (.x00mm) x7mm x7mm Screw (x5mm) Screw (x5mm) Washer(xmm) Spring Washer (mm) Nut (mm) Linkage Stopper Plastic tube (x0mm) Engine mount (x05mm) Blind Nut (mm) Main landing gear Blind Nut (mm) Washer(xmm) Nut (mm ) Screw (x5mm) Screw (x50mm) Washer (xmm) Wheel (00 mm) Fuel tank (550ml) 7 0 7
Assemble the wheels to the landing gear. The side view of the engline install completiom. Assemble the accelerateor push rod to the engine. 7 Mount the fuel tank to the fuselage. Set Screw (xmm) Linkage Stopper Fuel tank (550ml) Washer (xmm) Nut (mm) Nut (mm) Screw (x50mm) Washer (xmm) Wheel (00 mm) 0 mm Rod (x00mm) Washer (mm) Washer (xmm) Set Screw (mm) Set Screw (xmm) Rod (x500mm) Set Screw (mm) 9 Drill holes and set blind nut in appropriate position and assemble the main landing gear. Drill holes and set blind nut in appropriate position in the firewall before install the engine. 5 Engine installation finished sketch map. The detailed diagram of the fuel tank servo..mm Blind Nut (mm) Set screw (xmm) Blind Nut Washer (xmm) Main landing gear Screw(x5mm) Blind Nut (mm) 5.mm Blind Nut Washer (mm) Washer (mm) Linkage Stopper Washer (mm) Nut (mm) Set screw (xmm) 0 The front view of the engine install completion. Read the detailed diagram and install the engine. Assembly of the fuel tank. 9 Assemle the throttle servo to the fuselage. mm Throttle servo Washer (xmm) Screw (x5mm) mm In case of -cycle & -cycle engine. Washer (xmm) Screw (x5mm) Nut (mm) Spring Washer (mm) Washer (xmm) Fuel spray line Air pressure line Fuel supply line 9