SHELTER ASSEMBLY MANUAL MODEL: SIZE:24X12X6M
|
|
- Trevor Johns
- 5 years ago
- Views:
Transcription
1 SHELTER ASSEMBLY MANUAL MODEL: SIZE:24X12X6M
2 SPECIFICATION Length: 24m Width: 12m Height: 6m Door dimension: W4.27xH4.27m IMPORTANT----READ MANUAL FIRST Improper site preparation, assembly and maintenance may invalidate warranty and cause unnecessary and costly mistakes. If you have any questions contact your local dealer. For User Friendly assembly we have identified each individual component with the part code as indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly. It s necessary to tighten the roof fabric enough to avoid hammocks on the roof and also re-tighten once or twice again after a few months of use. This is important when assembly in cold weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric "slack" again and need to be re-tighten before next winter. It s the owners responsibility to take of snow immediately if not slide of by itself. READ ALL INSTRUCTIONS BEFORE ASSEMBLY 1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in high winds, or wet location. 2. Keep children away. All children should be kept away from the work area. Be aware of personal safety. Be careful not to pinch fingers with clips and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous fumes. 3. Do not over reach. Keep proper footing and balance at all times. 4. Do not assemble if under the influence of alcohol or drugs. Read warning labels on prescription to determine if your judgment or reflexes are impaired while taking drugs. IF there is any doubt, do not assemble. 5. Be aware of possible windy conditions; fasten the base in concrete if these situations may occur. Remove the cover during hurricane. 6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open flame. 7.Be aware of personal safety during assembly and use.be careful not to pinch fingers with clips and tubes when assembling.when using makes sure there is adequate ventilation for exhaust and other dangerous fumes. 1
3 PARTS LIST Part Code DESCRIPTION Q TY 1 Roof bent tube 13sets 2 Upper bent tube 24sets 2A Upper bent tube at front and back door 2sets 3 Lower bent tube 26sets 4 Standing leg 26 5 Purlin 84 6 Base plate at four corner 4 7 Base plate for standing legs 22 8 Base plate for mechanical door 2 9 Base plate for front and back door 6 9A Base plate on Zipper entrance door 1 10L Lower standing leg at left on front door 1 10R Lower standing leg at right on front door 1 10A The door splint 4 11L Upper standing leg at left on front door 1 11R Upper standing leg at right on front door 1 12 Door beam on front door 1set 12A Vertical support tube for door beam at front door 1 13 Lower standing leg at left on front door 1 13A Lower standing leg to connect mechanical door 1 13B Upper standing leg at middle at both door 2 13C Standing leg to connect zipper door 1 13D Lower standing leg on back door 4 14 Upper standing leg at middle of back door 2 14A Upper standing leg at side of back door 2 15 Upper horizontal tube at middle of front door 2 15A Horizontal tube at side of front door 1 15B Horizontal tube to connect zipper door at right 1 15C Middle horizontal tube at back door 6 15D Horizontal tube at shoulder of back door 2 16 Square tube to connect Gear 1 16A Gear 1 16B Steel wire for Mechanical door 1 17 Base tensioning tube at middle of front door 2 17A Base tensioning tube at side of front door 2 17B Base tensioning tube at back door 5 18 Steel 24 18A Clip Door Bracing Tube 7sets 20 Base tensioning tube for roof cover 2 21 Bolt 12x Bolt 10x Bolt 10x A Bolt 10x Bolt 10x Rope 1 26 Plastic cap for tensioning tube 24
4 27 Stake peg Door cover at front 1 29 Cover for front door 1 29A Cover for back door 1 30 Roof cover 1 31 Angel seat 5 32 PVC tube 2sets 33 Band for ratchet Ratchet 38 3
5 Figure 1 Frame Sketch L24xW12xH6m 4
6 A-EQUIPMENT AND TOOLS FOR INSTALLATION 1. Measuring Tape 2. String for alignment 3. Stake 4. Ladder or Scissors Lift 5. Sledge Hammer 6. Drill 7. Wrench 8.Knife INSTALLATION PROCESS A----BASE INSTALLATION Please refer to the diagram (Figure 2) to place the base plates: Figure 2 Base Plate installation 1. The measurement is from center to center of tubes on the base palates. Referring to the above diagram and confirm the place of base plates. There are there holes on the plates for stake pegs. Foundation placement As Figure 2 shows each Base plate is equipped with 3 pieces of Stake pegs.(no.27) Method of Placing Stake Peg 1. Mark the stake peg hold through the base plate by using the stake peg. Move the base plates away and the mark determines where the stake peg w ill be. 2. Note: The stake peg apply for normal conditions, not suitable to the rock ground, frozen soil and concrete ground. 5
7 B-FRAME INSTALLATION Figure 3 1. As Figure 3 shown to connect Roof bent tube(part No.1),Upper bent tube(part No.2),Lower bent tube(part No.3) and Standing leg(part No.4) by using Bolt 10x90(Part No.22),which makes one group of arches. 2. Note: Note: The Upper bent tube at front door (No.2A) which are welded with steel plates fare different from the middle arch. Please NOTE the direction of bolt, DO NOT install the Bolts on top of the truss where the fabric will rest. Figure 4 3.Insert one end of the assembled arch into one base palate and force the other end of the arch into the opposite base plate.(see Figure 4) 6
8 Figure 5 4.After finish installing the first two arches, connect the Purlin(Part No.5) on them by using Bolt 12x100(Part No.21).Then install the third arch into base plate and connect the purlin (see Figure 5). Finally install the Steel wire(part No.18) on Standing leg by using Clip(Part No.18A) )(See Figure 1) Do not tighten down the nuts completely until frame is fully assembled and set in place. the arches, the front and back panel should be assembled well on the ground before erected into the Base plate. C-DOOR INSTALLATION Front door Figure 6 7
9 Back door Figure 7 D DOOR DOOR INSTRUCTION 1. Install the front and back door frame as Figure 5 and Figure Use Knitting Rope (No.25) on Front and Back cover to lace the grommets in the end to the tensioning tubes evenly. The end covers are tied to the frame (Roof, Middle & Lower Bent Tube) by Knitting Rope. They are also been secured to the end frame (door tube and side rail) by Knitting Rope. 3. Method of Fastening Front and Back Cover Insert the Door Bracing Tube (No.19) into the bottom of Front door cover (No.28). Put the Nylon Rope into the door cover and the Small Pulley onto Support Crossbeam for roof cover like the Figure 6.Finally fix it onto the Base Plate (No.6). 4. Tidy the Back Cover and Front Cover. Fasten the band inside the end of the roof cover, make the cover well fold to the frame and tie the end of the band to the Clips on Base Plates at four corners. 8
10 E--- INSTALLING THE ROOF COVER NOTE: Do not install the cover onto the frame of your building in high wind conditions. 1. As Figure 7 shows, When the Roof cover (Part NO.30) is over top of Frame assembly(figure 8) fix it by using Ropes(Part No.25). Figure 8 Figure 9 As Figure 9 shows, align one side of Roof cover evenly front to back, then cut 6 pockets according to the position of the base plates and put the Lower tensioning tube for Roof cover(part No.30),for roof cover into the pocket of roof cover. add band(no.33) for tie down ratchet at each point alone the cover opening, Put band for tie down ratchets over cover tensioning tubes at each base plate alone one side. Bands do not attach to tensioning tubes, but loop around and secure at both ends on ratchet. 9
11 3. The roof cover is tensioned from front to back by the rope lacing to grommet flaps inside the main cover, inside the unit at both front and rear arches. using the rope provided, lace the main cover grommet flap around the main frame front and rear arch pieces. start in the top middle of each arch, and lace to each side. add rope length by tying pieces together or cutting as necessary. NOTE: DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANY CIRCUMSTANCES until the final assembly and tightening has been completed. The process is quite easy. But some tightening adjustments will be necessary to produce a flat, tensioned roof cover. Please adjust the roof cover every month. CONGRATULATIONS: NOW YOUR ASSEMBLY IS COMPLETED. 10
Installation Manual. T1220 Storage Shelter. v
Installation Manual T1220 Storage Shelter v.2 140820 SPECIFICATION Length: 21.4m Width: 12.2m Height: 7.6m Sidewall height:4.2m Door dimension: W4.5xH4.5m IMPORTANT----READ MANUAL FIRST Improper site preparation,
More informationSHELTER ASSEMBLY MANUAL Model # 3085GL-17P
SHELTER ASSEMBLY MANUAL Model # 3085GL-17P Strongly ask to remove snow from the roof immediately. Do not leave any snow load on the roof. Keep both sides and two ends on the ground clear all the times.
More informationSHELTER ASSEMBLY MANUAL MODEL # 1326P. L8.0xW4.0xH3.8m
SHELTER ASSEMBLY MANUAL MODEL # 1326P L8.0xW4.0xH3.8m SPECIFICATION Length: 8.0m Width: 4.0m Height: 3.8m (Please note the measurement is from center to center of the tubes) IMPORTANT-----READ MANUAL FIRST
More informationSHELTER ASSEMBLY MANUAL. Model #
SHELTER ASSEMBLY MANUAL Model # 203012 L9.1 x W6.1 x H3.66m SPECIFICATION Length: 9.1m Width: 6.1m Height: 3.66m Door dimension: W4.5m x H3.2m IMPORTANT-----READ MANUAL FIRST Improper site preparation,
More informationSHELTER ASSEMBLY MANUAL CONTAINER COVER
QuickTime and a decompressor are needed to see this picture. SHELTER ASSEMBLY MANUAL CONTAINER COVER L12.0xW10.0XH5.0m SPECIFICATION Length: 12.0m Width: 10.0m Height: 5.0m IMPORTANT-----READ MANUAL FIRST
More informationCARPORT/SHELTER MODEL: JIT L12.0xW6.2xH4.0M Installation Manual
CARPORT/SHELTER MODEL: JIT-2040 L12.0xW6.2xH4.0M www.vikre.no Installation Manual Congratulations on your purchase of our instant shelter. This unit is a combination of excellent manufacturing and design.
More informationDouble Truss Shelter Model# SST W9.14xL14.2xH4.88m Assembly Instructions
Double Truss Shelter Model# SST304716 W9.14xL14.2xH4.88m Assembly Instructions Page 1 RECOMMENDED TOOLS Equipment List Speed Wrench 22#.23#.24# Hammer (30lb) Rope (12#) Long Tape (50m) Hammer Drill*1 Lifter*2
More informationManual for Shelter W3,5xL8,0xH3,8m
Manual for Shelter W3,5xL8,0xH3,8m 22-11-2016 Congratulations on your purchase of our instant shelter. This unit is a combination of excellent manufacturing and design. It is comprised of a rigid frame
More informationCARPORT/SHELTER JIT-1333HZ. L10.0xW4.0xH4.5M Installation Manual MODEL:
CARPORT/SHELTER MODEL: JIT-1333HZ L10.0xW4.0xH4.5M www.vikre.no Installation Manual Congratulations on your purchase of our instant shelter. This unit is a combination of excellent manufacturing and design.
More informationInstallation Manual. for. Kroftman Storage Tent T520
Installation Manual for Kroftman Storage Tent T520 Congratulations on your purchase of our instant shelter. This unit is a combination of excellent manufacturing and design. It is comprised of a rigid
More informationAssembly Instructions
18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,
More informationAssembly Instructions 60x40x18 Domed Style Truss Building. ASSEMBLY INSTRUCTIONS DOMED STYLE 60x40x18
ASSEMBLY INSTRUCTIONS DOMED STYLE 60x40x18 Please read instructions completely before you begin. This will help attain the best results for your installation. CONGRATULATIONS! Congratulations on your purchase
More informationAssembly Instructions 40x60x18 Domed Style Truss Building. ASSEMBLY INSTRUCTIONS DOMED STYLE 40x60x18
ASSEMBLY INSTRUCTIONS DOMED STYLE 40x60x18 CONGRATULATIONS! Congratulations on your purchase of a Rhino Shelters 40x60x18 Round Style Portable Building. With proper installation, use and maintenance, your
More informationOpslagtent/Lagerzelt/Storage tent/abri de stockage. Kroftman T825. (7,90 x 25 m)
Opslagtent/Lagerzelt/Storage tent/abri de stockage Kroftman T825 (7,90 x 25 m) Montagehandleiding (Engels) Montageanleitung (Englisch) Installation manual Manuel de montage (Anglais) V03.01KR 190122 Congratulations
More informationAssembly Instructions 40x60x18 Domed Style Truss Building. ASSEMBLY INSTRUCTIONS DOMED STYLE 40x60x18
ASSEMBLY INSTRUCTIONS DOMED STYLE 40x60x18 CONGRATULATIONS! Congratulations on your purchase of a Big Bear buildings 40x60x18 Round Style Portable Building. With proper installation, use and maintenance,
More informationAssembly Instructions 30x65x15 Industrial Round Style Building
ASSEMBLY INSTRUCTIONS ROUND STYLE 30x65x15 Please read instructions completely before you begin. This will help attain the best results for your installation. CONGRATULATIONS! Congratulations on your purchase
More informationAssembly Instructions 30x40x15 Round Style Portable Building With Single Door. ASSEMBLY INSTRUCTIONS ROUND STYLE 30x40x15 WITH SINGLE DOOR
ASSEMBLY INSTRUCTIONS ROUND STYLE 30x40x15 WITH SINGLE DOOR Please read instructions completely before you begin. This will help attain the best results for your installation. CONGRATULATIONS! Congratulations
More information12x24x10 Run-In Shed #51451
12x24x10 Run-In Shed #51451 Please read instructions completely before assembly ATTENTION: BOLTS ARE NOT NEED- ED OR INCLUDED FOR EVERY CONNECTION BUT MAY BE PURCHASED BY CALL- ING THE NUMBER BELOW Description
More informationAssembly Instructions Round Style 30x65x15 Industrial Round Style Building
ASSEMBLY INSTRUCTIONS ROUND STYLE 30x65x15 Please read instructions completely before you begin. This will help attain the best results for your installation. CONGRATULATIONS! Congratulations on your purchase
More informationWeatherShield Daddy Long Legs Canopy
WeatherShield Daddy Long Legs Canopy Photo may show a different but similar model. 2010 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: 06.210 STK# 1220RV10W10
More informationAssembly Instructions Round Style 30x65x15-4 Industrial Round Style Building
ASSEMBLY INSTRUCTIONS ROUND STYLE 30x65x15-4 Please read instructions completely before you begin. This will help attain the best results for your installation. CONGRATULATIONS! Congratulations on your
More informationStandard 25 Wide Structure
Standard 25 Wide Structure Truss Arch Style 2 piece 12ft c/c typical Arch Depth 12 Webbing Diameter 1/2 1 run straight 2 runs straight Wind Brace - up to 120 8 Wind Brace - up to 192 12 Wind Brace - over
More informationWeatherShield Covered Walkway and Connect-A-Building
WeatherShield Covered Walkway and Connect-A-Building Photo may show a different but similar model. 2014 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104303
More informationMARQUEE INSTALLATION HANDBOOK. Curved Structures
MARQUEE INSTALLATION HANDBOOK Curved Structures 12m Curved Roof Beam Assembly Instructions Ensure there are no overhead or underground obstructions or services before starting to assemble frame. Square
More informationClearSpan Round Style Mini Garage
ClearSpan Round Style Mini Garage Photo may show a different but similar model. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# PB01900R4 DIMENSIONS 8' W x 8' H
More informationClearSpan Mini Cold Frames
ClearSpan Mini Cold Frames Photo may show a different but similar model. 2009 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 105152 6' W x 5' H x 6' L 105153
More informationClearSpan Mini Grab Bag Shelters
ClearSpan Mini Grab Bag Shelters Photo may show a different but similar model. Baseboard is not included. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS
More informationMoo-Tel Calf Hutch CLEARSPAN ANIMAL HOUSING W x 12 L W x 18 L W x 24 L
Moo-Tel Calf Hutch Photo may show a different but similar model. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 102852 14 W x 12 L 102853 14 W x 18 L
More informationClearSpan End Frame Kit 30' Wide x 11' High
ClearSpan End Frame Kit 30' Wide x 11' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and mounting feet shown in the above diagram
More informationOpen shipping crate and separate all of the different parts. Over The Top Shelters LLC
ASSEMBLY INSTRUCTIONS FOR MODEL SH122110GN and SH122110GY Open shipping crate and separate all of the different parts. Count each part and match up with parts list. Shortages or damaged parts should be
More informationClearSpan Economy Round Style High Tunnel
ClearSpan Economy Round Style High Tunnel Photo may show a different but similar model. 2012 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: 0112 STK# PB01725R6
More informationflex Installation multiflex
flex Installation Manual12m multiflex Table of Contents Page# Bolts........................................................................ 3 General Information.........................................................
More informationClearSpan Attached-Style Awning
ClearSpan Attached-Style Awning Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: July 2007ldg STK# DIMENSIONS
More informationClearSpan End Frame Kit 26' Wide x 12' High
ClearSpan End Frame Kit 26' Wide x 12' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and struts shown in the above diagram are
More informationClearSpan SolarGuard Round Style Storage Building
ClearSpan SolarGuard Round Style Storage Building Photo may show a different but similar model. 2009 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: 131.09
More informationASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER
ASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER Our unique assembly process quickly transforms individual pieces into a finished structure that will give you a lifetime of service. Great care has been taken
More information50 W ide. Future Trac G able E nd. Installation Instructions AIGE
G able E nd W ide TopTec Products, LLC 7601 Highway 221 Moore, SC 29369 Phone: (800) 845-2830 Fax: (800) 921-77 e-mail: sales@toptecproducts.com www.toptecproducts.com AIGE 2003915 General Information
More informationClearSpan Super Moo-Tel Building 26' Wide
ClearSpan Super Moo-Tel Building 26' Wide Photo may show a different but similar model. 2012 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# PB01500R3/R4 PB01510R3/R4
More informationClearSpan 20' Wide Free-Standing Building
ClearSpan 20' Wide Free-Standing Building Photo may show a different but similar model. 2018 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# PB00580R3/R4 PB00582R3/R4
More informationClearSpan Mini Grab Bag Shelters
ClearSpan Mini Grab Bag Shelters Photo may show a different but similar model. Baseboard is not included. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS
More informationGrowSpan Round Premium High Tunnels
GrowSpan Round Premium High Tunnels Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# PB01680R4 PB01690R4 DIMENSIONS
More informationGrowSpan Round Cold Frames
GrowSpan Round Cold Frames Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 103099 12' W x 8' H x 24'
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: April 2007ldg STK# DIMENSIONS
More informationClearSpan Grab Bag Canopy
ClearSpan Grab Bag Canopy Photo may show a different but similar model. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104385 10 W x 20 L 1 YOU MUST
More informationROUND TOP RV SHELTER
ROUND TOP RV SHELTER 94182 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More information22'W x 13'H Peak Style Shelter Frame Assembly Instructions
22'W x 13'H Peak Style Shelter Frame Assembly Instructions Recommended Tools Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored. THIS IS A TEMPORARY STRUCTURE AND
More informationMATERIALS DESCRIPTON QUANITY INCLUDED A
STORAGE SOLUTIONS ITEM# IS 08220 12 wide x 8 6 high x 20 long MATERIALS DESCRIPTON QUANITY INCLUDED A Curved Pipe Male/Female 18 B Curved Pipe Male/Male 6 C Long Connector Bolts/Nus 30 D Horizontal Straight
More informationLange Crank Hoist-a-top Assembly Instructions
Lange Crank Hoist-a-top Assembly Instructions Installation Time: 1-4 Hours depending on skill level Tools Required: Cordless Drill Level Stud Finder Ratcheting wrench 9/16 socket or wrench 11/16 socket
More informationConstruction Instructions for Continental and Quickfit Clearspan Frame Marquees
Construction Instructions for Continental and Quickfit Clearspan Frame Marquees ERECTION INSTRUCTIONS - CONTINENTAL & QUICKFIT FRAME TENTS CONTINENTAL & QUICKFIT FRAME TENTS A system of clearspan frame
More informationHip Roof Canopy Instructions
Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting
More informationWOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
More informationINSTALLATION INSTRUCTIONS SUBURBAN SERIES CARPORT 25 X 20 X 6 LENGTH CAN BE EXTENDED IN 4 1/2 INCREMENTS HEIGHT CAN BE EXTENDED IN 1 INCREMENTS
INSTALLATION INSTRUCTIONS SUBURBAN SERIES CARPORT 25 X 20 X 6 LENGTH CAN BE EXTENDED IN 4 1/2 INCREMENTS HEIGHT CAN BE EXTENDED IN 1 INCREMENTS BASIC FRAME SIZES (NO EXTENSIONS): 25-1/2 X 18' x 6 EAVE
More information10' W x 8' H or 10' H Round Style Shelter Assembly Instructions
10' W x 8' H or 10' H Round Style Shelter Assembly Instructions Description 10' x 8' x 8' Round Style Shelter - Gray 10' x 8' x 10' Round Style Shelter - Gray Recommended Tools Please read instructions
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More information12'W x 10'H RoundTop Frame Assembly Please read and understand instructions completely before assembly.
12'W x 10'H RoundTop Frame Assembly Please read and understand instructions completely before assembly. Layout out frame parts as shown and match up items with quantity to make sure no parts are missing.
More informationCARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES
CARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES FRAME SIZES: WIDTH: 12, 14, 18, 20, 24, AND 30 ON CENTER FRAME SPACING: 4 1/2 FRAME LENGTH: 18 EAVE HEIGHTS: START AT 7 TO 12 1/2. Our unique
More informationMoo-Tel Small Animal Hut
Moo-Tel Small Animal Hut Photo may show a different but similar model. 2010 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104602 4 6" W x 4' 10" H x 8 2"
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More information6m x 12m CREST INSTRUCTIONS
WARNING READ INSTRUCTIONS CAREFULLY BEFORE USE Recommended procedure below. For safety reasons it is recommended that four persons set up any marquee. Ensure area is free from any sharp objects & overhead
More information12'W x 20'L x 10'H Run-in-Shed Assembly Instructions
12'W x 20'L x 10'H Run-in-Shed Assembly Instructions Description Model # 12'W x 20'L x 10'H Run-In-Shed 51351 Recommended Tools Please read instructions COMPLETELY before assembly. This shelter MUST be
More informationClearSpan 38' Wide Aircraft Hangar
ClearSpan 38' Wide Aircraft Hangar Photo may show a model of a different length. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 107556 38' W x 15' H
More informationClearSpan Open Garages
ClearSpan Open Garages Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# PB02910R4 DIMENSIONS 18' W x 16' H x 52' L YOU
More informationClearSpan Front Roll-Up Kit Installation Guide
ClearSpan Front Roll-Up Kit Installation Guide Roll-up panel opened. Roll-up panel closed. Actual building and panel may differ from what is shown. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited
More informationOutdoor Water Solutions, Inc. Small Backyard Windmill. Installation Manual
Outdoor Water Solutions, Inc. Small Backyard Windmill Installation Manual Customer Service: 1-866-471-1614 Website: www.outdoorwatersolutions.com Springdale, Arkansas 72764 Phone: 1-866-471-1614 Fax: 1-479-750-9178
More informationThank you for purchasing our product! *Please read these instructions and follow them step by step.*
07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group
More informationLedger Board Lean-to Instruction Manual
Ledger Board Lean-to Instruction Manual for 18 x 24 2 x 8 covers Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you a lifetime of service.
More informationASSEMBLY INSTRUCTIONS FOR STORETTE STA42
ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 A01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read the safety information
More informationUNIVERSAL INSTALLATION INSTRUCTIONS FOR CARPORTS
UNIVERSAL INSTALLATION INSTRUCTIONS FOR CARPORTS FRAME SIZES: WIDTH: 10, 12, 14, 16, 18, 20, 24, AND 30 ON CENTER FRAME SPACING: 4, 4 1/2, AND 5 FRAME LENGTH: 4 ON CENTER 20-2, 4 1/2 ON CENTER 18 AND 5
More informationFOR PROFESSIONAL GARAGE DOOR INSTALLERS
Composite Garage Doors Installation Instructions FOR PROFESSIONAL GARAGE DOOR INSTALLERS Tools required Screwdriver Claw Hammer Locking Pliers Power Drill Level with a 3/32" Drill Bit Utility Knife 9/16",
More informationTensile Traditional Marque Installation Manual
Tensile Traditional Marque Installation Manual Tensile Traditional Marquee Installation Instructions Tools Needed: Sledgehammers/Mechanical Wackers Gloves Ladder and Stepladder Safety helmets Method: 1.
More informationLM600 Landmark Permanent Blind
LM600 Landmark Permanent Blind Get parts online at www.huntriversedge.com P/N: 23033 REV1: 02/23/16 2016 RETI All Rights Reserved INTRODUCTION Landmark Permanent Blinds are engineered with you the hunter
More informationElite Home-Attached Greenhouse
Elite Home-Attached Greenhouse Photo may show a greenhouse of a different length. Elite Home-Attached Greenhouse Use these instructions for the following greenhouses: #104711 #104713 #104715 2007 ClearSpan
More informationU.S. Rack, Inc Falcon Drive, Madera, CA APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK
U.S. Rack, Inc. 2850 Falcon Drive, Madera, CA 93637 15APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationREV: 1.2 TRAMPOLINE MANUAL
REV: 1.2 TRAMPOLINE MANUAL TRAMPOLINE PARTS LIST: Item 8FT 10FT 12FT 14FT 16FT A 1 1 1 1 1 B 1 1 1 1 1 C 6 8 12 12 12 E 48 64 72 96 108 F 6 8 12 12 12 G 3 4 6 6 6 H 12 16 24 24 24 I 1 1 1 1 1 DIAGRAMS
More informationPergola PR100N1. Assembly Instructions. Systems Trading Corporation Customer service: (877)
FABRIC Pergola PR00N Assembly Instructions Systems Trading Corporation Customer service: (8)82 82 of 20 Introduction Thank you for purchasing the Pergola PR00N. When properly assembled and maintained,
More informationInstallation Manual FLUSH MOUNT - Shingle, Slate,etc. Questions? Call Us! +1 (800)
www.trasnowandsun.com S Installation Manual FLUSH MOUNT - Shingle, Slate,etc. At TRA Snow and Sun we engineer and layout each project upon request free of charge. Just give us the project details and we
More informationLedger Board Lean-to Instruction Manual
Ledger Board Lean-to Instruction Manual for 18 x 24 2 x 8 /12 6 covers ROOF ONLY ROOF WITH GABLES 2-SIDED FRAME ONLY 2-SIDED WITH GABLES Our unique assembly process quickly transforms the individual pieces
More informationGrowSpan Series 500 Roll-Up Ends
GrowSpan Series 500 Roll-Up Ends Photo may show a different but similar model. Doorframe materials are not included. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission.
More information8 x 10 GREENHOUSE. Visit our website at:
8 x 10 GREENHOUSE With Two Vents 9390 Assembly Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
More informationAssembly Instructions Barn Style 12 x 28 x 12
ASSEMBLY INSTRUCTIONS BARN STYLE 12Wx28Lx12H Congratulations! Congratulations on your purchase of a Barn Style Portable Building by MDM Products LLC. With proper installation, use, and maintenance, your
More informationSteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF
SteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF Please read fully before commencing work...any queries will be promptly answered, contact theboss@steelchief.com.aui MPORTANT
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationClearSpan Majestic Greenhouse Film Roof with Roll-up Sides
ClearSpan Majestic Greenhouse Film Roof with Roll-up Sides 28' Wide Photo may show a different but similar model. 2009 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK#
More informationRoof Only Lean-to Instruction Manual
Roof Only Lean-to Instruction Manual for 10 x 20 2 x 8 /10 6 covers Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you a lifetime of service.
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationGarage-in-a-Box SUV/Truck 13' x 20' x 12' Peak Style Shelter Assembly Instructions
Garage-in-a-Box SUV/Truck 13' x 20' x 12' Peak Style Shelter Assembly Instructions Description Model # Garage-in-a-Box SUV/Truck 13' x 20' x 12' - Green 62694 Recommended Tools Please read instructions
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS SINGLE DOOR GARAGE AVAILABLE IN 12, 20, 24 AND 30 WIDTHS DOUBLE DOOR GARAGE AVAILABLE IN 24 AND 30 WIDTHS Our unique assembly process quickly
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationAssembly Instructions Shed House Style 12 x 12 x 8
ASSEMBLY INSTRUCTIONS SHED STYLE 12Wx12Lx8H Congratulations! Congratulations on your purchase of a Shed Style Instant Shelter by MDM Products LLC. With proper installation, use, and maintenance, your new
More informationAssembly Instructions Greenhouse House Style 12 x 24 x 8
ASSEMBLY INSTRUCTIONS GREENHOUSE HOUSE STYLE 12Wx24Lx8H Congratulations! Congratulations on your purchase of an Extended House Style Greenhouse by MDM Products LLC. With proper installation, use, and maintenance,
More informationCTTR Tire Rack Required tools
CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions
More informationGrowSpan Gothic HobbyPro Greenhouses
GrowSpan Gothic HobbyPro Greenhouses Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104889 16 W x
More information6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box Assembly Instructions
6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box Assembly Instructions Description Model # 6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box 70652 Recommended Tools Please read instructions COMPLETELY before assembly.
More information11 x11 Pergola. Assembly Instructions. Paragon Group USA cm cm cm
FABRIC x Pergola Assembly Instructions 0cm 9 2cm 0cm 0 20cm Paragon Group USA Customer Service:(8) 82 82 Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the x Pergola. When
More informationLow Headroom Rear Mount TorqueMaster
Low Headroom Rear Mount Supplemental Instruction Insert This supplemental installation instruction is to be used as a supplement to the main Installation Instruction and Owner s Manual provided with the
More informationBumper Sign INSTALLATION INSTRUCTIONS
Bumper Sign INSTALLATION INSTRUCTIONS BUMPERSIGN TOOL CHECKLIST SDS MAX Rotary Hammer Drill Marker/Pencil SDS MAX 1 Carbide Drill Bit Tape Measure Torque Wrench with ½ Drive Power Source Vacuum ½ Drive
More informationClearSpan 36' Wide Pony Wall Building
ClearSpan 36' Wide Pony Wall Building Ground Level Photo may show a model of a different length. Cover is not shown. 2017 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK#
More informationClearView Panels Mil 3 Finished Sides with Grommets 1 Hem Side Mil 3 Finished Sides with Grommets 1 Hem Side DESCRIPTION
ClearView Panels Photo may show a different but similar model. 2006 FarmTek All Rights Reserved. Reproduction is prohibited without permission. Revision date: November 2006rp STK# DESCRIPTION 105659 16
More information