Aliphatic Resin Wood Glue. Launch Lug. Part #10009 Kevlar* Cord. Part #J0053

Transcription

1 ADANCED Prod No * What you will need to build the Quest Lil GRUNT Hobby Knife * Pencil Straight Edge Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest Lil GRUNT Nose Cone 36" Fabric Streamer Part #82307 Decal Sheet Part #20050 Part # Body Tube Part #117900L Elastic Cord Red Thrust Ring Part #J0060 Part #14105 Launch Lug Centering Rings Part #16030 Part #10009 Kevlar* Cord Part #J0053 Motor Mount Tube Part #11300 Motor Clip Part #49000 Three Laser Cut Fins Part #33008 Notice: Parts not illustrated to scale *Kevlar is a trademark of Dupont Corp. Page 01

2 ADANCED LET'S BUILD THE 1 Assemble shock cord Locate both ends of the Kevlar Both ends of cord and one end of the elastic Kevlar cord cord. Tie the Kevlar and elastic cord together with a secure knot. Now stretch it out so it is one long assembly. Single end of Elastic cord Kevlar cord Knot Knot Completed shock cord assembly elastic cord 2 Assemble motor mount Place the Red Thrust Ring up against the side of the Motor Mount Tube and use it as a guide to cut a 1/8 inch long slit in the side of the Motor Mount Tube as shown. Insert the Motor Clip into the slit in the Motor Mount Tube. Wrap a piece of tape all the way around the Motor Mount Tube to hold the Motor Clip in place. Apply Wood around inside edge of Motor Mount Tube as shown. Insert the Red Thrust Ring into the Motor Mount Tube so it is even with the top of the Motor Mount Tube. E. Now apply a of Wood around the Motor Mount Tube 1/2" from the rear end as shown. Slide one of the Centering Rings onto the Motor Mount Tube and into the of. E. 3 Shock cord attachment Use a slip knot to tie the Kevlar end of the shock cord around the Motor Mount Tube above the attached Centering Ring. Slip the elastic end of the shock cord through the other Centering Ring, Now apply a of Wood around the Motor Mount Tube 1/2" from the top end as shown. Slide the other Centering Ring onto the Motor Mount Tube and into the of. Pass loose ends through loop 4 Motor mount insertion Thread the shock cord through the body tube. Apply Wood around the inside of the Body Tube as shown. Immediately insert the Motor Mount in the Body Tube and PUSH INTO THE BODY TUBE WITH ONE FAST & SMOOTH MOTION until it sticks out 1/4" from the rear of body tube as shown. Lil GRUNT Fin Marking guide Page 02 Lil GRUNT Fin Marking guide TAB

3 ADANCED BUILDING THE QUEST Lil GRUNT 5 Mark fin lines on body tube Cut out the fin marking guide, wrap it around the motor mount end of the body tube and use it to mark the fin locations. Then use a straight edge or door frame to extend the lines 5" from the rear of the tube. Make a pencil mark 1 from the end of Body Tube along Fin Lines. Set tube against door frame, then use the door frame edge to guide pencil to extend fin placement lines. 6 Create double glue joint How to make a "Double Joint" for extra fin strength Apply a small line of wood glue to the root edge of the fin. Attach it to the body tube in correct position. Remove the fin and wipe away any excess glue on the fin and the body tube so there is only a very thin layer of glue left. Wait until the glue is dry, then re-apply a new line of glue to the root edge of the fin and re-attach the fin. Press on Pull off 7 Attach three fins Using Wood, attach the fins one by one using the fin markings to align and place them. Make sure they are straight! YES! Set fins so they are at 120 degree angles to one another. NO! 8 Add glue fillet to fins Run a of Wood along the length of the root edge of the fins to make a fillet. Use your finger to smooth the fillet and remove excess glue. 9 Attach launch lug to body tube Using Wood, attach the launch lug to the body tube 2-3/4" from the fin end, make sure it is straight and not aligned with a fin! 2-3/4" from motor end of body tube Launch lug clear for launch rod. Page 03

4 10 Sanding and finishing ADANCED Apply a coat of Sanding Sealer to each Fin. When the Sealer is dry, lightly sand each Fin. Repeat the sanding and sealing until the surface of each Fin is smooth. Thoroughly dust the rocket so it is clean and ready for painting. 11 Painting the Lil GRUNT Mask off the shoulder of the Nose Cone with Masking Tape and newspaper. Mask off from this ridge. Place a rolled up newspaper in the Motor Mount to act as a handle to hold while painting the rocket. Spray the entire rocket with Olive Drab Enamel Spray Paint. 12 Attach nose cone to shock cord Thread the shock cord through the eyelet on the nose cone, and tie two overhand knots, leaving about 3 of overhang. 13 Attach streamer to shock cord Thread the shock cord overhang through the grommet on the streamer, then tie it securely using two overhand knots. Spray the exposed surfaces of the Nose Cone with Silver Enamel Spray Paint. 14 Decal application The Decals in this kit are peel and stick, no wetting with water is required. To allow more versatility in the placement of the Decals, cut them apart, peel off backing, then dip them in a shallow bowl of water with a drop of dish soap. The Decals can then be repositioned for a short time, then burnished down. Place the Decals in the appropriate positions shown. One star on each Fin. Page 04 Part No A

5 You can fly the High-Q with D12-3 or D12-5 rocket motors. We recommend the Quest Launch Pad Prod. No with the below addition and the Quest Launch Controller Prod. No For wadding use Quest Wadding Prod. No ADANCED FLYING YOUR Lil GRUNT ROCKET Flying your Lil GRUNT with a "D" size Motor "U" shaped stakes hammered into the ground over each launch pad leg. Note! Due to the size of the Lil GRUNT, it is recommended that a wire clothes hanger be cut into 3 "U" shaped stakes and hammered into the ground over each launch pad leg. Prepping the Lil GRUNT Rocket for Flight Roll the Streamer from it s loose end. Don t roll it too tightly, but it should be compact enough to slide easily into the body tube. DO NOT wrap the shroud lines around the Streamer. Place 3 sheets of loosely crumpled wadding inside the body tube. Pack the Streamer and Shock Cord, then replace Nose Cone 3 sheets of loosely crumpled wadding Pack the Streamer and Shock Cord, then replace Nose Cone Prepping Rocket Motors Follow the Rocket Motor manufacturer's instructions on using rocket motors. Use the appropriate launch pad and launch controller for the motor you are using (described above). READ AND FOLLOW THE N.R. SAFETY CODE DURING ALL YOUR MODEL ROCKET ACTIITIES. READ AND FOLLOW THE ENCLOSED LAUNCHING PROCEDURES SHEET. Manufactured by: Quest Aerospace, Inc. PO Box 2409 Pagosa Springs, CO All Rights Reserved Page 05