.500. location of stopscrews for Drill thru & c-bore for #10 S.H.C.S. (2) .60. #10-32 air connection (2).189 dia (2)

Transcription

1 A -1 otary rive ully Adjustable eatures Angle of rotation adjusted with built in stop screws with fine threads top screws are compatible with sensing switches esigned for production rates and long life wo sealed ball bearings at top and bottom of drive shaft apped holes and offset dowel pin area in shaft and driving flange allows higher torque transmittal and accuracy imensions earings are positioned very close to the drive gear for rigidity, precision, wear resistance and accuracy. haft is stopped with an adjustable hard stopscrew against a hardened pin, eliminating backlash x.19 dp stopscrew # 5/ position sensing switches (optional).60 location of stopscrews for 0-90 rill thru & c-bore for #10... (2) #8-32 tap.375 dia. 31/32 dia #10-32 air connection (2).189 dia (2) ote: shown in mid-position ek rive rystal ake, elephone 815/ AX 815/ ev. 9/04

2 -1 otary rive echnical ata ore = 0.5 epeat accuracy = +/ ife expectancy = 5-6 million cycles ompressed air = 60 to 100 psi Angle of rotation = 0 to 180 degrees Weight = 1 lbs Air connection = ax radial bearing load = 4 lbs ax axial bearing load = 6 lbs ax oad (lbs) oad vs. istance for ifferent ycle imes (@80psi) oad (for any ) = raph value *(/80).9 sec.7 sec.5 sec oad istance (in) ptions ensing switches are available as an option. hey are mounted to the stopscrews as seen in the photo to the right. or specifications on sensing please see page 143. ressure iston Area (in^2). ptional sensing switches available. ee pages y ax orque (in-lbs) he diagrams above depict the load () on an arm of length = y. Also shown is the torque of the -1 which is given in the chart: his chart shows how the cycle time of the -1 is affected by the amount of load and distance the load is from the shaft, for 180 rotation. or operating pressures other than 80, take value from graph and multiply by (ressure in psi/80). A ev. 9/ ek rive rystal ake, elephone 815/ AX 815/

3 A -2 otary rive ully Adjustable eatures Angle of rotation adjusted with built in stop screws with fine threads top screws are compatible with sensing switches nd stops deceleration with available cushions or shocks esigned for production rates and long life wo sealed ball bearings at top and bottom of drive shaft apped holes and offset dowel pin area in shaft and driving flange allows higher torque transmittal and accuracy earings are positioned very close to the drive imensions 1.25 #10-32 air connection (2) can be rotated x.23 dp 8.88 approx. w/cushions dia. (2) 3.75 gear for rigidity, precision, wear resistance and accuracy. haft is stopped with an adjustable hard stopscrew against a hardened pin, eliminating backlash.686 location for 0-90 position stopscrews # 5/ position (sensing switches optional).62 drill thru & c'bore top & bottom for #10... (2 plcs) ote: shown in mid-position optional -2 shocks or -1.5 hydraulic ends (2) 1.12 dia..50 dia. 1/2-20 tapped for cushions or plugs (both ends) ek rive rystal ake, elephone 815/ AX 815/ ev. 9/04

4 -2 otary rive echnical ata ore = 0.75" epeat accuracy = +/ " ife expectancy = 5-6 million cycles ompressed air = 60 to 100 psi Angle of rotation = 0 to 180 degrees Weight = 2 lbs Air connection = ax radial bearing load = 8 lbs ax axial bearing load = 12 lbs ax oad (lbs) oad vs. istance for ifferent ycle imes (@80psi) oad (for any ) = raph value *(/80) 1 sec.8 sec.6 sec oad istance (in) ptions ensing switches are available as an option. hey are mounted to the stopscrews as seen in the photo to the right. or specifications on sensing please see page 143. hocks or cushions are also available. y ressure iston Area (in^2) ptional sensing switches available. ee pages ax orque (in-lbs) he diagrams above depict the load () on an arm of length = y. Also shown is the torque of the -2 which is given in the chart: his chart shows how the cycle time of the -2 is affected by the amount of load and distance the load is from the shaft, for 180 rotation. or operating pressures other than 80, take value from graph and multiply by (ressure in psi/80). A ev. 9/ ek rive rystal ake, elephone 815/ AX 815/

5 A -3 otary rive ully Adjustable eatures Angle of rotation adjusted with built in stop screws with fine threads top screws are compatible with sensing switches nd stops deceleration with available cushions esigned for production rates and long life iston has hardened pin to strike for longevity wo sealed ball bearings at top and bottom of drive shaft apped holes and offset dowel pin area in shaft and driving flange allows higher torque transmittal and accuracy earings are positioned very close to the drive imensions sensing switches (optional) stopscrews #5/16 (2) position location for 0-90 pos drill & c bore top & bottom for 1/4" screw (2) approx. w/cushions dia (2) /4-28 tap gear for rigidity, precision, wear resistance and accuracy. haft is stopped with an adjustable hard stopscrew against a hardened pin, eliminating backlash dia. x 1/4 for dowel pin additional mounting holes 1/4-20 tap (4) ptional -1.5 or -2 hydraulic cushions.75 ote: shown in mid-position /2-20 tap for cushions or plugs (both ends).50 dia dia. 1/8 air connections ek rive rystal ake, elephone 815/ AX 815/ ev. 9/04

6 -3 otary rive echnical ata ore = 1.25 epeat accuracy = +/ ife expectancy = 5-6 million cycles ompressed air = 60 to 100 psi Angle of rotation = 0 to 180 degrees Weight = 5 lbs Air connection = ax radial bearing load = 20 lbs ax axial bearing load = 36 lbs ax oad (lbs) oad vs. istance for ifferent ycle imes (@80psi) oad (for any ) = raph value *(/80) 1.2 sec.9 sec.6 sec oad istance (in) ptions ensing switches are available as an option. hey are mounted to the stopscrews as seen in the photo to the right. or specifications on sensing please see page 143. hocks or cushions are also available. y ressure iston Area (in^2) ptional sensing switches available. ee pages ax orque (in-lbs) he diagrams above depict the load () on an arm of length = y. Also shown is the torque of the -3 which is given in the chart: his chart shows how the cycle time of the -3 is affected by the amount of load and distance the load is from the shaft, for 180 rotation. or operating pressures other than 80, take value from graph and multiply by (ressure in psi/80). A ev. 9/ ek rive rystal ake, elephone 815/ AX 815/

7 A -4 otary rive ully Adjustable eatures Angle of rotation adjusted with built in stop screws with fine threads top screws are compatible with sensing switches nd stops deceleration with available cushions esigned for production rates and long life iston has hardened pin to strike for longevity wo sealed ball bearings at top and bottom of drive shaft apped holes and offset dowel pin area in shaft and driving flange allows higher torque transmittal and accuracy imensions 1/4 air connection (2) can be rotated.376 (2) x.38 dp. on bolt circle 5/16-24 tap (2) on bolt circle 5/16-18 tap (4 plcs) mounting holes for additional mounting stopscrews #1/2 (2) approx. w/cushions dia optional sensing switch dia (2) earings are positioned very close to the drive gear for rigidity, precision, wear resistance and accuracy. haft is stopped with an adjustable hard stopscrew against a hardened pin, eliminating backlash.938 drill thru & c'bore both sides for 5/16...(2 plcs) optional -2, -3 hydraulic cushions (2) ote: shown in mid-position /2-20 tapped end caps ek rive rystal ake, elephone 815/ AX 815/ ev. 9/04

8 -4 otary rive echnical ata ore = 2.00 epeat accuracy = +/ ife expectancy = 5-6 million cycles ompressed air = 60 to 100 psi Angle of rotation = 0 to 180 degrees Weight = 9.5 lbs Air connection = 1/4 ax radial bearing load = 60 lbs ax axial bearing load = 100 lbs ax oad (lbs) oad vs. istance for ifferent ycle imes (@80psi) oad (for any ) = raph value *(/80) 2 sec 1.5 sec 1 sec ptions ensing switches are available as an option. hey are mounted to the stopscrews as seen in the photo to the right. or specifications on sensing please see page 143. hocks or cushions are also available. y ressure oad istance (in) iston Area (in^2) ptional sensing switches available. ee pages ax orque (in-lbs) he diagrams above depict the load () on an arm of length = y. Also shown is the torque of the -4 which is given in the chart: his chart shows how the cycle time of the -4 is affected by the amount of load and distance the load is from the shaft, for 180 rotation. or operating pressures other than 80, take value from graph and multiply by (ressure in psi/80). A ev. 9/ ek rive rystal ake, elephone 815/ AX 815/