Hex Cap Screws Coarse & Fine Thread
|
|
- Aron Fletcher
- 5 years ago
- Views:
Transcription
1 INDUSTRIAL Product Description Hex head cap screws are manufactured to dimensional standards of ASME B and to various material and mechanical standards of ASTM and SAE. The length of a cap screw is measured from under the head to the extreme end of the screw. The standard thread length is two times the diameter plus 1/4 up to 6 length and two times the diameter plus 1/2 for screws longer than 6. Shorter length screws are fully threaded. Product standards require the manufacturer s head marking to appear on the top of all hex cap screws 1/4 diameter and larger. Grade 2 (A307A) Cap Screws are fasteners made from low carbon steel that achieve their strength primarily from cold working during the cold forming manufacturing Economical for use in non-critical applications where the fastener is not subject to extreme temperatures or stress. Cap Screws are medium strength fasteners that achieve their strength from a quench and temper heat treatment and have a greater tensile strength than a Grade 2. Yield-to-tensile ratio is the lowest of all heat treated steels. Cap Screws are the highest strength of standard inch series cap screws and are made from alloy steel and have greater tensile strength than Grade 5. Designed for use in high stress applications. 1/4-20 Coarse Thread 1/4-28 Fine Thread 1/2" 25C50HCS2Z 25C50HCS5Z 25F50HCS5Z 25C50HCS8Y 25F50HCS8Y 100 5/8" 25C62HCS2Z 25C62HCS5Z 25F62HCS5Z 25C62HCS8Y 25F62HCS8Y 100 3/4" 25C75HCS2Z 25C75HCS5Z 25F75HCS5Z 25C75HCS8Y 25F75HCS8Y 100 7/8" 25C87HCS2Z 25C87HCS5Z 25F87HCS5Z 25C87HCS8Y 25F87HCS8Y 100 1" 25C100HCS2Z 25C100HCS5Z 25F100HCS5Z 25C100HCS8Y 25F100HCS8Y /4 25C125HCS2Z 25C125HCS5Z 25F125HCS5Z 25C125HCS8Y 25F125HCS8Y /2" 25C150HCS2Z 25C150HCS5Z 25F150HCS5Z 25C150HCS8Y 25F150HCS8Y /4" 25C175HCS2Z 25C175HCS5Z 25F175HCS5Z 25C175HCS8Y 25F175HCS8Y 100 2" 25C200HCS2Z 25C200HCS5Z 25F200HCS5Z 25C200HCS8Y 25F200HCS8Y /4" 25C225HCS2Z 25C225HCS5Z 25F225HCS5Z 25C225HCS8Y 25F225HCS8Y /2 25C250HCS2Z 25C250HCS5Z 25F250HCS5Z 25C250HCS8Y 25F250HCS8Y /4" 25C275HCS2Z 25C275HCS5Z 25F275HCS5Z 25C275HCS8Y 25F275HCS8Y 100 3" 25C300HCS2Z 25C300HCS5Z 25F300HCS5Z 25C300HCS8Y 25F300HCS8Y /4" 25C325HCS2Z 25C325HCS5Z 25F325HCS5Z 25C325HCS8Y 25F325HCS8Y /2" 25C350HCS2Z 25C350HCS5Z 25F350HCS5Z 25C350HCS8Y 25F350HCS8Y 100 4" 25C400HCS2Z 25C400HCS5Z 25F400HCS5Z 25C400HCS8Y 25F400HCS8Y /2" 25C450HCS2Z 25C450HCS5Z 25F450HCS5Z 25C450HCS8Y 25F450HCS8Y 100 5" 25C500HCS5Z 25C500HCS5Z 25F500HCS5Z 25C500HCS8Y 25F500HCS8Y /2" 25C550HCS2Z 25C550HCS5Z 25F550HCS5Z 25C550HCS8Y 25F550HCS8Y 100 6" 25C600HCS2Z 25C600HCS5Z 25F600HCS5Z 25C600HCS8Y 25F600HCS8Y 100 5/16-18 Coarse Thread 5/16-24 Fine Thread 1/2" 31C50HCS2Z 31C50HCS5Z 31F50HCS5Z 31C50HCS8Y 31F50HCS8Y 100 5/8" 31C62HCS2Z 31C62HCS5Z 31F62HCS5Z 31C62HCS8Y 31F62HCS8Y 100 3/4" 31C75HCS2Z 31C75HCS5Z 31F75HCS5Z 31C75HCS8Y 31F75HCS8Y 100 7/8" 31C87HCS2Z 31C87HCS5Z 31F87HCS5Z 31C87HCS8Y 31F87HCS8Y 100 1" 31C100HCS2Z 31C100HCS5Z 31F100HCS5Z 31C100HCS8Y 31F100HCS8Y /4" 31C125HCS2Z 31C125HCS5Z 31F125HCS5Z 31C125HCS8Y 31F125HCS8Y /2" 31C150HCS2Z 31C150HCS5Z 31F150HCS5Z 31C150HCS8Y 31F150HCS8Y /4" 31C175HCS2Z 31C175HCS5Z 31F175HCS5Z 31C175HCS8Y 31F175HCS8Y 100 2" 31C200HCS2Z 31C200HCS5Z 31F200HCS5Z 31C200HCS8Y 31F200HCS8Y /4" 31C225HCS2Z 31C225HCS5Z 31F225HCS5Z 31C225HCS8Y 31F225HCS8Y /2 31C250HCS2Z 31C250HCS5Z 31F250HCS5Z 31C250HCS8Y 31F250HCS8Y /4" 31C275HCS2Z 31C275HCS5Z 31F275HCS5Z 31C275HCS8Y 31F275HCS8Y 100 3" 31C300HCS2Z 31C300HCS5Z 31F300HCS5Z 31C300HCS8Y 31F300HCS8Y /4" 31C325HCS2Z 31C325HCS5Z 31F325HCS5Z 31C325HCS8Y 31F325HCS8Y /2" 31C350HCS2Z 31C350HCS5Z 31F350HCS5Z 31C350HCS8Y 31F350HCS8Y 50 4" 31C400HCS2Z 31C400HCS5Z 31F400HCS5Z 31C400HCS8Y 31F400HCS8Y /2" 31C450HCS2Z 31C450HCS5Z 31F450HCS5Z 31C450HCS8Y 31F450HCS8Y 50 5" 31C500HCS5Z 31C500HCS5Z 31F500HCS5Z 31C500HCS8Y 31F500HCS8Y /2" 31C550HCS2Z 31C550HCS5Z 31F550HCS5Z 31C550HCS8Y 31F550HCS8Y 50 6" 31C600HCS2Z 31C600HCS5Z 31F600HCS5Z 31C600HCS8Y 31F600HCS8Y 50 D-17
2 INDUSTRIAL Grade 2 (A307A) 3/8-16 Coarse Thread 3/8-24 Fine Thread 1/2" 37C50HCS2Z 37C50HCS5Z 37F50HCS5Z 37C50HCS8Y 37F50HCS8Y 100 5/8" 37C62HCS2Z 37C62HCS5Z 37F62HCS5Z 37C62HCS8Y 37F62HCS8Y 100 3/4" 37C75HCS2Z 37C75HCS5Z 37F75HCS5Z 37C75HCS8Y 37F75HCS8Y 100 7/8" 37C87HCS2Z 37C87HCS5Z 37F87HCS5Z 37C87HCS8Y 37F87HCS8Y 100 1" 37C100HCS2Z 37C100HCS5Z 37F100HCS5Z 37C100HCS8Y 37F100HCS8Y /4" 37C125HCS2Z 37C125HCS5Z 37F125HCS5Z 37C125HCS8Y 37F125HCS8Y /2" 37C150HCS2Z 37C150HCS5Z 37F150HCS5Z 37C150HCS8Y 37F150HCS8Y /4" 37C175HCS2Z 37C175HCS5Z 37F175HCS5Z 37C175HCS8Y 37F175HCS8Y 100 2" 37C200HCS2Z 37C200HCS5Z 37F200HCS5Z 37C200HCS8Y 37F200HCS8Y /4" 37C225HCS2Z 37C225HCS5Z 37F225HCS5Z 37C225HCS8Y 37F225HCS8Y /2 37C250HCS2Z 37C250HCS5Z 37F250HCS5Z 37C250HCS8Y 37F250HCS8Y /4" 37C275HCS2Z 37C275HCS5Z 37F275HCS5Z 37C275HCS8Y 37F275HCS8Y 50 3" 37C300HCS2Z 37C300HCS5Z 37F300HCS5Z 37C300HCS8Y 37F300HCS8Y /4" 37C325HCS2Z 37C325HCS5Z 37F325HCS5Z 37C325HCS8Y 37F325HCS8Y /2" 37C350HCS2Z 37C350HCS5Z 37F350HCS5Z 37C350HCS8Y 37F350HCS8Y 50 4" 37C400HCS2Z 37C400HCS5Z 37F400HCS5Z 37C400HCS8Y 37F400HCS8Y /2" 37C450HCS2Z 37C450HCS5Z 37F450HCS5Z 37C450HCS8Y 37F450HCS8Y 50 5" 37C500HCS5Z 37C500HCS5Z 37F500HCS5Z 37C500HCS8Y 37F500HCS8Y /2" 37C550HCS2Z 37C550HCS5Z 37F550HCS5Z 37C550HCS8Y 37F550HCS8Y 50 6" 37C600HCS2Z 37C600HCS5Z 37F600HCS5Z 37C600HCS8Y 37F600HCS8Y 50 7/16-14 Coarse Thread 7/16-20 Fine Thread 3/4" 43C75HCS2Z 43C75HCS5Z 43F75HCS5Z 43C75HCS8Y 43F75HCS8Y 100 7/8" 43C87HCS2Z 43C87HCS5Z 43F87HCS5Z 43C87HCS8Y 43F87HCS8Y 100 1" 43C100HCS2Z 43C100HCS5Z 43F100HCS5Z 43C100HCS8Y 43F100HCS8Y /4" 43C125HCS2Z 43C125HCS5Z 43F125HCS5Z 43C125HCS8Y 43F125HCS8Y /2" 43C150HCS2Z 43C150HCS5Z 43F150HCS5Z 43C150HCS8Y 43F150HCS8Y /4" 43C175HCS2Z 43C175HCS5Z 43F175HCS5Z 43C175HCS8Y 43F175HCS8Y 50 2" 43C200HCS2Z 43C200HCS5Z 43F200HCS5Z 43C200HCS8Y 43F200HCS8Y /4" 43C225HCS2Z 43C225HCS5Z 43F225HCS5Z 43C225HCS8Y 43F225HCS8Y /2 43C250HCS2Z 43C250HCS5Z 43F250HCS5Z 43C250HCS8Y 43F250HCS8Y /4" 43C275HCS2Z 43C275HCS5Z 43F275HCS5Z 43C275HCS8Y 43F275HCS8Y 50 3" 43C300HCS2Z 43C300HCS5Z 43F300HCS5Z 43C300HCS8Y 43F300HCS8Y /4" 43C325HCS2Z 43C325HCS5Z 43F325HCS5Z 43C325HCS8Y 43F325HCS8Y /2" 43C350HCS2Z 43C350HCS5Z 43F350HCS5Z 43C350HCS8Y 43F350HCS8Y 25 4" 43C400HCS2Z 43C400HCS5Z 43F400HCS5Z 43C400HCS8Y 43F400HCS8Y /2" 43C450HCS2Z 43C450HCS5Z 43F450HCS5Z 43C450HCS8Y 43F450HCS8Y 25 5" 43C500HCS5Z 43C500HCS5Z 43F500HCS5Z 43C500HCS8Y 43F500HCS8Y /2" 43C550HCS2Z 43C550HCS5Z 43F550HCS5Z 43C550HCS8Y 43F550HCS8Y 25 6" 43C600HCS2Z 43C600HCS5Z 43F600HCS5Z 43C600HCS8Y 43F600HCS8Y 25 D-18
3 INDUSTRIAL Grade 2 (A307A) 1/2-13 Coarse Thread 1/2-20 Fine Thread 3/4" 50C75HCS2Z 50C75HCS5Z 50F75HCS5Z 50C75HCS8Y 50F75HCS8Y 50 1" 50C100HCS2Z 50C100HCS5Z 50F100HCS5Z 50C100HCS8Y 50F100HCS8Y /4" 50C125HCS2Z 50C125HCS5Z 50F125HCS5Z 50C125HCS8Y 50F125HCS8Y /2" 50C150HCS2Z 50C150HCS5Z 50F150HCS5Z 50C150HCS8Y 50F150HCS8Y /4" 50C175HCS2Z 50C175HCS5Z 50F175HCS5Z 50C175HCS8Y 50F175HCS8Y 50 2" 50C200HCS2Z 50C200HCS5Z 50F200HCS5Z 50C200HCS8Y 50F200HCS8Y /4" 50C225HCS2Z 50C225HCS5Z 50F225HCS5Z 50C225HCS8Y 50F225HCS8Y /2 50C250HCS2Z 50C250HCS5Z 50F250HCS5Z 50C250HCS8Y 50F250HCS8Y /4" 50C275HCS2Z 50C275HCS5Z 50F275HCS5Z 50C275HCS8Y 50F275HCS8Y 50 3" 50C300HCS2Z 50C300HCS5Z 50F300HCS5Z 50C300HCS8Y 50F300HCS8Y /4" 50C325HCS2Z 50C325HCS5Z 50F325HCS5Z 50C325HCS8Y 50F325HCS8Y /2" 50C350HCS2Z 50C350HCS5Z 50F350HCS5Z 50C350HCS8Y 50F350HCS8Y 25 4" 50C400HCS2Z 50C400HCS5Z 50F400HCS5Z 50C400HCS8Y 50F400HCS8Y /2" 50C450HCS2Z 50C450HCS5Z 50F450HCS5Z 50C450HCS8Y 50F450HCS8Y 25 5" 50C500HCS5Z 50C500HCS5Z 50F500HCS5Z 50C500HCS8Y 50F500HCS8Y /2" 50C550HCS2Z 50C550HCS5Z 50F550HCS5Z 50C550HCS8Y 50F550HCS8Y 25 6" 50C600HCS2Z 50C600HCS5Z 50F600HCS5Z 50C600HCS8Y 50F600HCS8Y 25 9/16-12 Coarse Thread 9/16-18 Fine Thread 1" 56C100HCS2Z 56C100HCS5Z 56F100HCS5Z 56C100HCS8Y 56F100HCS8Y /4" 56C125HCS2Z 56C125HCS5Z 56F125HCS5Z 56C125HCS8Y 56F125HCS8Y /2" 56C150HCS2Z 56C150HCS5Z 56F150HCS5Z 56C150HCS8Y 56F150HCS8Y /4" 56C175HCS2Z 56C175HCS5Z 56F175HCS5Z 56C175HCS8Y 56F175HCS8Y 25 2" 56C200HCS2Z 56C200HCS5Z 56F200HCS5Z 56C200HCS8Y 56F200HCS8Y /4" 56C225HCS2Z 56C225HCS5Z 56F225HCS5Z 56C225HCS8Y 56F225HCS8Y /2 56C250HCS2Z 56C250HCS5Z 56F250HCS5Z 56C250HCS8Y 56F250HCS8Y /4" 56C275HCS2Z 56C275HCS5Z 56F275HCS5Z 56C275HCS8Y 56F275HCS8Y 25 3" 56C300HCS2Z 56C300HCS5Z 56F300HCS5Z 56C300HCS8Y 56F300HCS8Y /4" 56C325HCS2Z 56C325HCS5Z 56F325HCS5Z 56C325HCS8Y 56F325HCS8Y /2" 56C350HCS2Z 56C350HCS5Z 56F350HCS5Z 56C350HCS8Y 56F350HCS8Y 25 4" 56C400HCS2Z 56C400HCS5Z 56F400HCS5Z 56C400HCS8Y 56F400HCS8Y /2" 56C450HCS2Z 56C450HCS5Z 56F450HCS5Z 56C450HCS8Y 56F450HCS8Y 25 5" 56C500HCS5Z 56C500HCS5Z 56F500HCS5Z 56C500HCS8Y 56F500HCS8Y /2" 56C550HCS2Z 56C550HCS5Z 56F550HCS5Z 56C550HCS8Y 56F550HCS8Y 25 6" 56C600HCS2Z 56C600HCS5Z 56F600HCS5Z 56C600HCS8Y 56F600HCS8Y 25 D-19
4 INDUSTRIAL Grade 2 (A307A) 7/8-9 Coarse Thread 7/8-14 Fine Thread 1-1/2" 87C150HCS2Z 87C150HCS5Z 87F150HCS5Z 87C150HCS8Y 87F150HCS8Y /4" 87C175HCS2Z 87C175HCS5Z 87F175HCS5Z 87C175HCS8Y 87F175HCS8Y 15 2" 87C200HCS2Z 87C200HCS5Z 87F200HCS5Z 87C200HCS8Y 87F200HCS8Y /4" 87C225HCS2Z 87C225HCS5Z 87F225HCS5Z 87C225HCS8Y 87F225HCS8Y /2 87C250HCS2Z 87C250HCS5Z 87F250HCS5Z 87C250HCS8Y 87F250HCS8Y /4" 87C275HCS2Z 87C275HCS5Z 87F275HCS5Z 87C275HCS8Y 87F275HCS8Y 15 3" 87C300HCS2Z 87C300HCS5Z 87F300HCS5Z 87C300HCS8Y 87F300HCS8Y /4" 87C325HCS2Z 87C325HCS5Z 87F325HCS5Z 87C325HCS8Y 87F325HCS8Y /2" 87C350HCS2Z 87C350HCS5Z 87F350HCS5Z 87C350HCS8Y 87F350HCS8Y 15 4" 87C400HCS2Z 87C400HCS5Z 87F400HCS5Z 87C400HCS8Y 87F400HCS8Y /2" 87C450HCS2Z 87C450HCS5Z 87F450HCS5Z 87C450HCS8Y 87F450HCS8Y 15 5" 87C500HCS5Z 87C500HCS5Z 87F500HCS5Z 87C500HCS8Y 87F500HCS8Y /2" 87C550HCS2Z 87C550HCS5Z 87F550HCS5Z 87C550HCS8Y 87F550HCS8Y 15 6" 87C600HCS2Z 87C600HCS5Z 87F600HCS5Z 87C600HCS8Y 87F600HCS8Y Coarse Thread 1-14 Fine Thread 2" 100C200HCS2Z 100C200HCS5Z 100F200HCS5Z 100C200HCS8Y 100F200HCS8Y /4" 100C225HCS2Z 100C225HCS5Z 100F225HCS5Z 100C225HCS8Y 100F225HCS8Y /2 100C250HCS2Z 100C250HCS5Z 100F250HCS5Z 100C250HCS8Y 100F250HCS8Y /4" 100C275HCS2Z 100C275HCS5Z 100F275HCS5Z 100C275HCS8Y 100F275HCS8Y 10 3" 100C300HCS2Z 100C300HCS5Z 100F300HCS5Z 100C300HCS8Y 100F300HCS8Y /4" 100C325HCS2Z 100C325HCS5Z 100F325HCS5Z 100C325HCS8Y 100F325HCS8Y /2" 100C350HCS2Z 100C350HCS5Z 100F350HCS5Z 100C350HCS8Y 100F350HCS8Y 10 4" 100C400HCS2Z 100C400HCS5Z 100F400HCS5Z 100C400HCS8Y 100F400HCS8Y /2" 100C450HCS2Z 100C450HCS5Z 100F450HCS5Z 100C450HCS8Y 100F450HCS8Y 10 5" 100C500HCS5Z 100C500HCS5Z 100F500HCS5Z 100C500HCS8Y 100F500HCS8Y /2" 100C550HCS2Z 100C550HCS5Z 100F550HCS5Z 100C550HCS8Y 100F550HCS8Y 10 6" 100C600HCS2Z 100C600HCS5Z 100F600HCS5Z 100C600HCS8Y 100F600HCS8Y 10 D-20
5 INDUSTRIAL Hex Cap ScrewsCoarse & Fine Thread Grade 2(A307A) Hex Head Cap Screws Mechanical Specifications SPECIFICATIONS MATERIAL SIZE RANGE MIN. PROOF MIN. TENSILE CORE HARDNESS MIN. YIELD INCHES STRENGTH PSI STRENGTH PSI MIN. - MAX STRENGTH PSI SAE J429 Grade 2 Low Carbon Steel 1/4"-3/4" 55,000 74,000 B80-B100 57,000 SAE J429 Grade 2 Low Carbon Steel 7/8"-1-1/2" 33,000 60,000 B70-B100 36,000 SAE J429 Grade 5 Medium Carbon Steel 1/4"-1" 85, ,000 C25-C34 92,000 SAE J429 Grade 5 Medium Carbon Steel 1-1/8"-1-1/2" 74, ,000 C19-C30 81,000 SAE J429 Grade 8 Med. Carbon Alloy Steel 1/4"-1-1/2" 120, ,000 C33-C39 130,000 H E F G <L T L> Underside of Head Dimensional Specifications E F G H L T NOMINAL OR BASIC BODY WIDTH WIDTH HEAD THREAD LENGTH PRODUCT DIAMETER DIAMETER ACROSS FLATS ACROSS CORNER HEIGHT SCREW LENGTHS MAX MIN BASIC MAX MIN MAX MIN BASIC MAX MIN <6 REF 6 >REF 1/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / D-21
6 INDUSTRIAL Hex Head Bolts Hot Dip Galvanized Hex Head Bolts Grade 2 (A307A) Hex Bolts are fasteners made from low carbon steel that achieve their strength primarily from cold working during the cold forming manufacturing operation. Hot-dip galvanized steel has been effectively used for more than 150 years. The value of hot-dip galvanizing stems from the relative corrosion resistance of zinc, which under most service conditions is considerably better than iron and steel. In addition to forming a physical barrier against corrosion, zinc, applied as a hot-dip galvanized coating protects exposed steel. Furthermore, galvanizing for protection of iron and steel is favored because of its low cost, the ease of application, and the extended maintenance-free service that it provides. Hot-dip galvanized threaded bolts require tapped oversize hex nuts Hex Head Bolts, Steel Hot-Dip Galvanized 1/4-20 Diameter 5/16-18 Diameter 3/8-16 Diameter LENGTH ITEM CODE BOX LENGTH ITEM CODE BOX LENGTH ITEM CODE BOX GRADE 2 QTY. GRADE 2 QTY. GRADE 2 QTY. 1" 25C100HCSH /4" 25C125HCSH /2" 25C150HCSH 100 2" 25C200HCSH /2" 25C250HCSH 100 3" 25C300HCSH 100 4" 25C400HCSH 100 5" 25C500HCSH 100 6" 25C600HCSH 100 8" 25C800HCSH 100 1" 50C100HCSH /4" 50C125HCSH /2" 50C150HCSH 50 2" 50C200HCSH /2" 50C250HCSH 50 3" 50C300HCSH /2" 50C350HCSH 25 4" 50C400HCSH 25 5" 50C500HCSH 25 6" 50C600HCSH 25 8" 50C800HCSH 25 10" 50C1000HCSH 25 12" 50C1200HCSH 25 1" 31C100HCSH /4" 31C125HCSH /2" 31C150HCSH 100 2" 31C200HCSH /2" 31C250HCSH 100 3" 31C300HCSH 100 4" 31C400HCSH 50 5" 31C500HCSH 50 6" 31C600HCSH 50 8" 31C800HCSH 50 1/2-13 Diameter 5/8-11 Diameter 3/4-10 Diameter 1" 1-1/4" 1-1/2" 62C150HCSH 25 2" 62C200HCSH /2 62C250HCSH 25 3" 62C300HCSH /2" 62C350HCSH 25 4" 62C400HCSH 25 5" 62C500HCSH C600HCSH 25 8" 62C800HCSH 25 10" 62C1000HCSH 25 12" 62C1200HCSH 25 1" 37C100HCSH /4" 37C125HCSH /2" 37C150HCSH 100 2" 37C200HCSH /2 37C250HCSH 50 3" 37C300HCSH 50 4" 37C400HCSH 50 5" 37C500HCSH C600HCSH 50 8" 37C800HCSH 50 10" 37C1000HCSH 50 12" 31C1200HCSH 50 1" 1-1/4" 1-1/2" 2" 75C200HCSH /2" 75C250HCSH 20 3" 75C300HCSH /2" 75C350HCSH 20 4" 75C400HCSH 20 5" 75C500HCSH 20 6" 75C600HCSH 20 8" 75C800HCSH 20 10" 75C1000HCSH 20 12" 75C1200HCSH 20 Hanger Bolts Steel Zinc Plated Hanger Bolts Bolt with lag screw thread on one end and machine screw thread on the other. Hanger Bolts, Steel Zinc Plated #10-24 Diameter 1/4-20 Diam. 5/16-18 Diam. 3/8-16 Diam. LENGTH ITEM BOX ITEM BOX ITEM BOX ITEM BOX CODE QTY. CODE QTY. CODE QTY. CODE QTY. 1-1/2" 10C150BHAZ 100 2" 10C200BHAZ /2" 10C250BHAZ 100 3" 10C300BHAZ /2" 4" 5" 6" 8" 10" 25C150BHAZ C200BHAZ C250BHAZ C300BHAZ C350BHAZ C400BHAZ C150BHAZ C200BHAZ C250BHAZ C300BHAZ C350BHAZ 50 31C400BHAZ 50 31C500BHAZ 50 31C600BHAZ 50 37C200BHAZ C250BHAZ 50 37C300BHAZ 50 37C350BHAZ 50 37C400BHAZ 50 37C500BHAZ 50 37C600BHAZ 50 37C800BHAZ 50 37C1000BHAZ 50 D-23
FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson.
FASTENERS PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. Quick Reference Nuts Heavy Hex Nuts...4
More informationChemical composition. Type 2 as per F568: C ( ); P (max 0.048); S (max 0.058); Mn (min 0.74); B (min );
BS EN 14399 HIGH STRENGTH STRUCTURAL BOLTING FOR PRE LOAD Direct comparison as an alternative to ASTM HSFG Bolts ASTM A325M Type 1, ASTM A490M Type 1 or 2 BS EN 14399-3:2005 Grade 8.8 and 10.9 Chemical
More informationBOLTS AND NUTS Square Bolts( Table 1 ) Hex Nuts ( Table 7 ) Heavy Hex Nuts (Table 7) Heavy Hex Structural Bolts ( Table 2 )
BOLTS AND NUTS 1493 An externally threaded fastener that must be assembled with a nut to perform its intended service is a bolt. (Example: heavy hex structural bolt.) An externally threaded fastener that
More informationStandard Specification for Carbon and Alloy Steel Nuts [Metric] 1
Designation: A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric] 1 This standard is issued under the fixed designation A 563M; the number immediately following the designation
More informationODOT ITB Group 4 Item 33 Qty. 1
ODOT ITB 180-17 Group 4 Item 33 Qty. 1 ODOT ITB 180-17 Group 4 Item 34 Qty. 1 ODOT ITB 180-17 Group 4 Item 35 Qty. 1 ODOT ITB 180-17 Group 4 Item 36 Qty. 1 STRUCTURAL BOLTS NUCOR FASTENER TECHNICAL
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.
Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These
More informationMETRIC FASTENERS 1520 METRIC FASTENERS
1520 METRIC FASTENERS METRIC FASTENERS A number of American National Standards covering metric bolts, screws, nuts, and washers have been established in cooperation with the Department of Defense in such
More informationFastener Basics. Common Fastener Types. Fastener Materials. Grade / Class and Fastener Strength
Fastener Basics Common Fastener Types Fastener Grade (US) or Class (metric) refers to the mechanical properties of the fastener material. Generally, a higher number indicates a stronger, more hardened
More informationStandard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1
Designation: A 325M 00 METRIC An American National Standard Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1 This standard is issued under the fixed designation A 325M;
More informationHEADLINE BUILDING MATERIALS
EADLINE BUILDING MATERIALS eb: www.hbm.ae l Email: commercial@hbm.ae eavy ex Structural Bolts ASTM A 325M Metric Series Dimensions P.O. Box 37366, Dubai, UAE l Tel: +971 4 3475675 l Fax: +971 4 347 5485
More informationAUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang.
Standard State SECTION A : SCREW THREAD Basic elements of screw thread design ANSI/ASME B1.7M Nomenclature.Definitions and letter symbols for screw thread ASME B1.1 Unified inch screw thread ( UN and UNF
More information01 FASTENERS JULY FASTENERS 1
01 FASTENERS 4 Bolts 22 Socket Screws 30 Nuts 39 Washers 53 Screws 72 Threaded Rods & Studs 73 Rivets, Rivnuts & Accessories 82 Retaining Rings 84 Pins, Links, & Sleeves 91 Key Stock & Assortments 90 Anchors
More informationGLOBALLOY THREADED ROD
GLOBALLOY THREADED ROD DESIGNED AND ENGINEERED TO REDUCE DOWNTIME AND MAINTENANCE COSTS SPECIAL ALLOY STEEL Over 145,000 PSI tensile strength in normal temperature application Minimum tensile strength
More informationFasteners. Fastener. Chapter 18
Fasteners Chapter 18 Material taken from Mott, 2003, Machine Elements in Mechanical Design Fastener A fastener is any device used to connect or join two or more components. The most common are threaded
More informationStandard Specification for Quenched and Tempered Steel Bolts and Studs 1
Designation: A 44 00 Standard Specification for Quenched and Tempered Steel Bolts and Studs This standard is issued under the fixed designation A 44; the number immediately following the designation indicates
More informationICC-ES Evaluation Report
ICC-ES Evaluation Report ESR-6 Reissued April, 009 This report is subject to re-examination in two years. www.icc-es.org (800) 4-6587 (56) 699-054 A Subsidiary of the International Code Council DIVISION:
More informationSpecifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish
Specifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish ASTM F 1667-05 Table 15 Type 1, Style 10 - Common Nails Size Length
More informationStandard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare 1
Designation: A 94 0 Standard Specification for Steel Transmission Tower olts, Zinc-Coated and are This standard is issued under the fixed designation A 94; the number immediately following the designation
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2012 Hilti North American MI/MQ Technical Guide Volume 3. For complete details on this product, including data development, general suitability, installation, and corrosion
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number ISO 10684:2004(E) ISO 2004 PDF
More informationDesignation: F
Designation: F 852 05 Standard Specification for Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 20/05 ksi Minimum Tensile Strength This standard is issued under
More informationTechnical Specifications Guide For Fasteners
fastrite_2011_fut.ai 8/4/11 4:29:01 PM Technical Specifications Guide For Fasteners C M Y CM MY CY CMY K Important Disclaimer All of the information provided in this publication is intended for reference
More informationStandard Specification for Carbons and Alloy Steel Nuts 1
Designation: A 563 07 Standard Specification for Carbons and Alloy Steel Nuts 1 This standard is issued under the fixed designation A 563; the number immediately following the designation indicates the
More informationSUBMITTAL INFORMATION "BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH
"BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH GRADE: LOW CARBON STEEL GRADE A GRADE B PHOSPHOROUS MAX % 0.06 0.04 SULFUR,
More information(Public Law ). Infasco Bolts are Original Equipment on both MACK and CATERPILLAR Products
INFASCO CAP SCREWS The Bolt of Choice for the Heavy Equipment Industry Infasco is the largest manufacturer of Grade 5 and Grade 8 Cap Screws in North America. They are accepted and used by all branches
More informationAS/NZS 1214:2016 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016
(ISO 10684:2004, MOD) Australian/New Zealand Standard Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016 This joint Australian/New Zealand standard was
More informationAttachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder. Installation Instructions Revised 9/2/2016
Attachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder Installation Instructions Revised 9/2/2016 SBCA has been the voice of the structural building components industry
More informationTable of Contents. GARD Specialists Co., Inc. GARD Specialists Co., Inc. P.O. Box 157 Eagle River, WI Fax
Table of Contents Heavy Duty Fasteners F-911 Fasteners Introduction... 2 F-911 Fasteners Specifications... 2 F-911 Fasteners Torque Chart... 3 Cap Screws - F-911 Alloy Hex Head, Coarse... 4-9 Assortments,
More informationMATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997
MATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997 This Standard is the property of Iranian Ministry of Petroleum. All rights
More informationStandard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare 1
Designation: A 94 0 e Standard Specification for Steel Transmission Tower olts, Zinc-Coated and are This standard is issued under the fixed designation A 94; the number immediately following the designation
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationPIP STF05121 Anchor Fabrication and Installation Into Concrete
June 2017 Structural PIP STF05121 Anchor Fabrication and Installation Into Concrete PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this
More informationDisclaimer. Socket Products Socket depth limits maximum torque. Torque figures are based on 80% of maximum torque for a given key size.
E546 V3 (1/17) Disclaimer Torque values listed in this book are based on mathematical calculations and experimental data. The values are valid only when the matched strength system listed is used. The
More informationFastener Basics. Common Fastener Types. Fastener Materials. Grade / Class and Fastener Strength
Fastener Basics Common Fastener Types Fastener Grade (US) or Class (metric) refers to the mechanical properties of the fastener material. Generally, a higher number indicates a stronger, more hardened
More informationUP4 LEARN-A-LOT (PLAYFUL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationREPORT HOLDER: SFS INTEC 1045 SPRING STREET WYOMISSING, PENNSYLVANIA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3870 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 05 00
More informationUP43 LEARN-A-L0T (NATURAL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationDTFACT 16 C IN PAVEMENT LIGHT FIXTURE TESTING AND ANALYSIS FINAL SUMMARY PRESENTATION
DTFACT 16 C 00047 IN PAVEMENT LIGHT FIXTURE TESTING AND ANALYSIS FINAL SUMMARY PRESENTATION IESALC Fall Technology Meeting Government Contacts Subcommittee Dallas, TX October 23, 2017 Jeremy N. Downs,
More informationSPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS
UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.
More informationAnchors. Easy Screw-In Style. Plastic & Die-cast Zinc EASY SCREW-IN ANCHOR. Specifications are for reference purposes only.
Plastic & Die-cast Zinc Easy Screw-In Style nchors D ESY SCREW-IN NCOR ITW Buildex* D Ultimate Tensile Strength Ultimate Shear Strength ead nchor ength Maximum Fixture Thickness Gypsum Thickness Gypsum
More informationKEEP YOUR RESOURCE MOVING.
LINER BOLTS KEEP YOUR RESOURCE MOVING. COLUMBUS McKINNON CORPORATION Leading the Industry Downtime in the grinding mill operation is caused by one of two things: regularly scheduled maintenance or unscheduled
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number
More informationSockets. Dimensions; Mechanical & Performance Requirements. Socket Head Cap Screws Body & Grip Lengths - Socket Cap Screws...
imensions; Mechanical & Performance Requirements Socket Head Cap Screws... 2-4 Body & Grip Lengths - Socket Cap Screws... 5-6 Low Head Socket Cap Screws... 7 Button Head Socket Cap Screws... 8 Flat Head
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More informationEngineering Test Report
Engineering Test Report Thermal Diffusion Galvanizing Report Poleline Hardware 02/01/2018 Allied Bolt s Thermal Diffusion Galvanizing Allied Bolt announces the launch of Thermal Diffusion Galvanized Poleline
More informationStandard Specification for High-Strength Steel Bolts, Classes 10.9 and , for Structural Steel Joints [Metric] 1
Designation: METRIC Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints [Metric] 1 This standard is issued under the fixed designation A 490M; the
More informationTECHNICAL CORRECTION October Process Industry Practices Structural. PIP STF05121 Fabrication and Installation of Anchor Bolts
TECHNICAL CORRECTION October 2006 Process Industry Practices Structural PIP STF05121 Fabrication and Installation of Anchor Bolts PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize
More informationERECTION & CONSTRUCTION
ERECTION & CONSTRUCTION High Strength Structural Bolting Author: Clark Hyland Affiliation: Steel Construction New Zealand Inc. Date: 24 th August 2007 Ref.: Key Words High Strength Bolts; Property Class
More informationPRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4884 HSD STANDARD SLIDING DOOR & Assembly Installation Instructions 4884 HSD Standard Sliding Door Components Some Considerations When Choosing Your Stall System - 1
More informationDIN, EN, ASTM. Металлопрокат и трубы по стандартам. Поставляем металлопрокат по стандарту ASTM A563
Металлопрокат и трубы по стандартам DIN, EN, ASTM Поставляем металлопрокат по стандарту ASTM A563 Для заказа металлопроката или получения консультации обращайтесь по следующим контактам: Россия: +7 (495)
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationSECTION MASONRY ANCHORAGE AND REINFORCEMENT. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 04080 MASONRY ANCHORAGE AND REINFORCEMENT Display hidden notes to specifier. (Don't know how? Click Here) A. Post installed masonry anchors. B. Miscellaneous
More informationUP133 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CL
UP33 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL TRIANGLE
More informationGovernment Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company.
Government Recognized Export House OHSAS 800:200 ISO 400:2004 PED Approved Company. Phone : +9 22 44 (2 Lines) Fax : +9 22 289 4 Email : export@reliablepipes.com domestic@reliablepipes.com Designation:
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:
More informationAugust 2015 Fastener Industry Technology Update from the IFI
INDUSTRIAL FASTENERS INSTITUTE August 4, 2015 August 2015 Fastener Industry Technology Update from the IFI 1. Standards Organizations Activities a. Standards published recently: i. ASTM A563 - Standard
More informationIn normal joints, the clamping force should equal the working load. In gasketed joints, it should be sufficient to create a seal.
Fastener Quality Act Information Unbrako offers this link to the National Institute of Standards homepage on the Fastener Quality Act as an aide to individuals who need detailed and complete information
More informationBolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step. Drills, Taps, & Bits. Hex Capscrews Grade 8 Grade 5 Grade 2 A325 A490 Specials
AU-VE-CO Bolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step Concrete Anchoring Adhesives Anchor Bolts Drop Ins Wedge Pins Cotter Dowel Hitch Spring Roll Taper Pipe Fittings Power Coil EZ
More informationSECTION CONCRETE ANCHORING. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 03 15 00 CONCRETE ANCHORING Display hidden notes to specifier. (Don't know how? Click Here) A. General purpose mechanical anchors for horizontal and vertical
More informationBarofor Round System (polyester coated) Panels, Posts, Accessories
1 Scope This Technical Data Sheet specifies the requirements for the Barofor Round System. The complete system exists of: Panels Posts Accessories such as fixation system and posts caps. Panels and posts
More informationStandard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners 1
Designation: F 568M 04 METRIC Standard Specification for Carbon and lloy Steel Externally Threaded Metric Fasteners This standard is issued under the fixed designation F 568M; the number immediately following
More informationHARDLOCK NUT RIM & HARDLOCK NUT BASIC
1 Clamp Load [kn] FEATURES OF HARDLOCK NUT Reusable without reduction in performance! Full torque management and completely fastened even with ZERO (0) clamp load! Available in various materials and surface
More information2016 AASHTO BRIDGE COMMITTEE AGENDA ITEM: 24 (REVISION 1) SUBJECT: LRFD Bridge Design Specifications: Section 6, Various Articles (2)
2016 AASHTO BRIDGE COMMITTEE AGENDA ITEM: 24 (REVISION 1) SUBJECT: LRFD Bridge Design Specifications: Section 6, Various Articles (2) TECHNICAL COMMITTEE: T-14 Steel REVISION ADDITION NEW DOCUMENT DESIGN
More informationSURFACE VEHICLE STANDARD
400 Commonwealth Drive, Warrendale, PA 15096-0001 SURFACE VEHICLE STANDARD J429 Issued 1949-01 Revised 1999-01 REV. JAN1999 Submitted for recognition as an American National Standard Superseding J429 MAY1998
More information3400 E. WALNUT STREET COLMAR, PA DORMAN / ROCKFORD
WEATHERLY #770 D-2013-A JUNE 2013 SUPERSEDES R-2009-F APR. 2009 2013 DORMAN / ROCKFORD 1-800-523-2492 Corporate Office & Customer Service www.dormanproducts.com 2013 Dorman Products, Inc. No reproduction
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationGround Clamps Cable Tray
commercial and industrial fittings: ing Fittings and Solderless Connectors Clamps Cable Tray Terminates ground wire to cable tray. For aluminum or copper conductors. 1 4 hex wrench tightens both tray and
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 42 687 (62) 699 04 www.icc es.org ESR 2442 Reissued 0/208 This report is subject to renewal 0/209. DIVISION: 06 00 00 WOOD,
More informationSwivel Hoist Ring Page 142
Swivel Hoist Ring Page 142 Hoist Rings Color coded to distinguish between UNC (Red) and Metric (Silver) thread types HR-125 M HR-125 Available in UNC and Metric thread sizes. UNC threads available in sizes
More informationSCREWS MACHINE. Slotted Phillips Six-Lobe Square Recess Pozi-Alternative Combination Recess Military Commercial Metric Inch
SCREWS MACHINE Slotted Phillips Six-obe Square Recess Pozi-Alternative Combination Recess Military Commercial Metric Inch INCH COMMERCIA COMBINATION DRIVE BINDING UNDERCUT FAT HEX WASHER Green (Header
More informationISO INTERNATIONAL STANDARD. Vis a f&e hexagonale partiellement filetees - Grades A er B. Third edition
NTERNATONAL STANDARD SO 401 4 Third edition 1999-09-01 Vis a f&e hexagonale partiellement filetees - Grades A er B Reference number SO 4014:1999(E) SO 401 4:1999(E) Foreword SO (the nternational Organization
More informationThreaded Products Gaskets & Seals Precision Machining
Threaded Products Gaskets & Seals Precision Machining FIRST CALL, ONLY CALL Dan-Loc Group was formed with the merger of Texthread, Dan-Loc Bolt & Gasket, and Spensall. Dan-Loc Group is a manufacturer and
More informationDown Stage Right -Theatrical and Entertainment Rigging Supplies
Shackle Plates There are five uniquely different designs in the Shackle Plates Dynasty. Each one allows you the freedom of choice as you design the rigging requirements of your scenery, as well as meeting
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationDIN 934 (1987) NEN 1560 NF E25-401
Hexagon nut DIN 94 (1987) NEN 1560 NF E25-401 Technical data d P m s M1 0,25 0,8 2,5 M1,2 0,25 1 M1,4 0, 1,2 M1,6 0,5 1,,2 M1,7 ( DIN) 0,5 1,4,5 M2 0,4 1,6 4 M2, ( DIN) 0,4 1,8 4,5 M2,5 0,45 2 5 M2,6 (
More informationEvaluation of In-Pavement Light Fixture Designs and Performance
Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of
More informationContinuous Fastener Galvanizing
Continuous Fastener Galvanizing The Continuous Fastener Galvanizing Process The Products it can produce The Markets it will service The Economics of the process The Investment required The Future Potential
More information1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners
Lecture Slides Screws, Fasteners, and the Design of Nonpermanent Joints Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance Adjustment 1 Introduction There are two distinct uses
More informationSCREW FASTENER SELECTION FOR COLD-FORMED STEEL FRAME CONSTRUCTION
test TECHNICAL NOTE On Cold-Formed Steel Construction $5.00 Cold-Formed Steel Engineers Institute Washington, DC www.cfsei.org 866-465-4732 SCREW FASTENER SELECTION FOR COLD-FORMED STEEL FRAME CONSTRUCTION
More informationHigh Tensile Steel Black Self-Colour Hexagon Socket Cap Head Screws: Metric Thread
Datasheet RS Stock No: 529703 High Tensile Steel Black Self-Colour Hexagon Socket Cap Head Screws: Metric Thread Socket caps have a small cylindrical head with tall vertical sides giving them space-saving
More informationContents. Grade 2, 5, 8 Hex Bolts 4. Heavy Hex Head Structural Bolts 6. A325 and A490 Tension Control Bolts (TC) 13. Nuts 22.
Who we are Amcan Jumax is the result of a merging between Boulons Jumax and Amcan Threaded Products, two successful companies well established, both with excellent reputations. The new entity is a bigger
More informationThis specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.
SPEC-3500 1/9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does
More informationSECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
More informationTesting. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.
907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing
More informationCOMPATIBILITY OF FASTENERS
COMPATIBILITY OF FASTENERS TECHNICAL BULLETIN Vol. 4, No. 2 NOVEMBER 2011 This bulletin applies to conditions where fasteners are not provided by Metl-Span. Profiled metal roof or wall panels rely upon
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationOSE Submittal July 20, 2018
SECTION 055000 - METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7.
DECKS Max. riser height-7 ¾ Min. tread depth-10 Landings required at (R311.7.5.1) (R311.7.5.2) top and bottom of stairs (R311.7.6) Notched guardrail post NOT allowed Graspable handrail required Spacing
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2442 Reissued 10/2017 This report is subject to renewal 10/2018. DIVISION: 06 00
More informationLetter of Transmittal/Submittal
Letter of Transmittal/Submittal FROM: TO: Baker Concrete Construction 1904 Jasper Street DATE JOB NUMBER 09/23/10 Aurora, CO 80011 9921 303.367.8111 ATTENTION Nick Dewald 937.536.9000 RE: Bruce Herman
More informationSECTION 3. BOLTS. bolt is a standard AN-type or a special-purpose bolt, and sometimes include the manufacturer.
9/8/98 AC 43.13-1B SECTION 3. BOLTS 7-34. GENERAL. Hardware is the term used to describe the various types of fasteners and small items used to assemble and repair aircraft structures and components. Only
More information1 Scope. 2 Normative references. 3 Dimensions. Page 2 DIN :
Page 2 1 Scope This standard specifies dimensions and technical delivery conditions for stud bolts with metric thread made of steel, stainless steel or nonferrous metal. 2 Normative references This standard
More informationThreaded Fasteners 2. Shigley s Mechanical Engineering Design
Threaded Fasteners 2 Bolted Joint Stiffnesses During bolt preload bolt is stretched members in grip are compressed When external load P is applied Bolt stretches further Members in grip uncompress some
More informationSwivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.
RIGGING ACCESSORIES Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. Available in UNC and Metric thread sizes. UNC threads available in sizes from 800 pounds to 100,000 pounds,
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Division 01 Specification
More informationANCHORS SLEEVE ANCHORS BOLT DIAMETER
SLEEVE ANCHORS No hole spotting. No mis-alignments. Simply drill through the fixture into concrete, insert and tighten. Preassembled for fast, easy installation. No special tools necessary; meets federal
More informationTAPPING SCREWS 1-1 TAPPING SCREWS PHILLIPS OVAL. 1 General Fasteners HEAD ZINC BLACK SIZE SIZE CHROME CHROMATE OXIDE
TAPPING SCREWS TAPPING SCREWS PHILLIPS OVAL HEAD ZINC BLACK SIZE SIZE CHROME CHROMATE OXIDE #4 x 3/8"... REG... 110001 #4 x 1/2"... REG... 105030... 110002 #4 x 5/8"... REG... 1 10003 #4 x 3/4"... REG...
More informationLimited Warranty And Exclusive Remedy
Limited Warranty And Exclusive Remedy THE WORLD LEADER Deepak Fasteners Ltd., through its Unbrako Division and associated companies, warrants that these products conform to industry standards specified
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More information