Supports up to 100 lbs / 45 kg

Size: px

Start display at page:

Download "Supports up to 100 lbs / 45 kg"

Brook French
5 years ago
Views:

1 User s Manual Supports up to 100 lbs / 45 kg U-PRO210 Included Mounting Hardware You Will Need 5 & 6 mm hex key 1 U-PRO210 mount (x1) 2 M4, M5 & M6 x 10 bolts (x4) 3 M4, M5 & M6 x 12 bolts (x4) 4 M4, M5 & M6 x 25 bolts (x4) 5 M4, M5 & M6 x 40 bolts (x4) 6 5/16 x 3 lag bolts (x2) 7 Concrete anchors (x2) 8 Ø 10 washers (x2) 9 Square washers Level Stud Finder C Marker D Drill E 3/16 or 3/8 drill bit F Hammer 400 mm VES extension (x4) To reach 400x400 mm use extensions rm Cable Cover Wall racket End Cover Tilt Cover racket var

2 WRNINGS & CUTIONS U-PRO210 IT IS HIGHLY RECOMMENDED THT THIS PRODUCT E INSTLLED Y PROFESSIONL. PLESE REVIEW THIS INSTRUCTION MNUL COMPLETELY E- FORE STRTING THE INSTLLTION PROCESS. WRNING: WRNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CUTION: CUTION alerts you the possibility of damage or destruction of equipment if you do not follow the corresponding instruction. WRNING: Improper installation can result in serious personal injury! Make sure that the structural members can support a weight factor five times the total weight of the equipment. If not, reinforce the structure before starting the installation. WRNING: e aware also of the potential for personal injury or damage to the unit if it is not adequately mounted. WRNING: The installer is responsible for verifying that the wall or ceiling to which the the mount is anchored will be safely support the combined load of all attached components or other equipment. Disclaimer: ProMounts intends to make this manual accurate and complete. However, ProMounts makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. ProMounts makes no representation of warranty, expressed or implied, regarding the information contained herein. ProMounts assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. WRNING: The weight of the display placed on the mount must not exceed the maximum load capacity of the mount. WRNING: Watch for pinch points. Do not put your fingers between movable parts. WRNING: Make sure the mount and brackets are correctly oriented. CUTION: Check the unit for shipping damage before you begin the installation. 2

3 INSTLLTION U-PRO210 1 Step 1: Separate arm from display bracket: 1.1 Dissassemble tilt mechanism by loosening top bolts () and removing lower bolts (). 1.2 Pull up and away the display bracket from the arm. 2 Step 2: Mount TV on display bracket: 2.1 Loosen 4 adaptor plate bolts (C) so both Vars (D) can slide. 2.2 Slide Vbars to match mounting holes on TV. 2.3 Insert matching TV bolts (E) and tighten slightly. 2.4 Tighten adaptor plate bolts (D) 2.5 Re-assemble tilt mechanism. C D E

4 INSTLLTION (2) U-PRO210 3 Step 3: a) Mounting to a wood stud: 3.0a Locate the wood stud. 3.1a Place the mount to a suitable location and height. 3.2a Using a bubble level, hold the mount in a level position and mark the holes position. 3.3a Drill 3/16 holes. F G b) Mounting to a masonry wall: 3.1b Place the mount to a suitable location and height. 3.2b Using a bubble level, hold the mount in a level position and mark the holes position. 3.3b Drill 3/8 holes, insert the wall anchor and tap them flush to the wall with a hammer ttach the mount to the wall with the lag bolts (F) and steel washers (G) supplied. 3.5 While the lag bolts are still slightly loose, check to make sure that the mounting plate is vertical. djust if necessary. Covered with the supplied molded caps. H Step 4: Reattach tilt mechanism: 4.1 Put back the display bracket on the arm hanging on left bolts (). 4.2 Put back removed bolts (). 4.3 Leave bolts ( and ) while adjusting tilt angle. 4.4 Tighten at desired position. 4.5 If necessary, adjust horizon with bolts (H). 4

5 INSTLLTION (3) U-PRO210 I 5 Step 5: Cable Management: 5.1 To install the cable, first you need to remove the end cover (I) and slide the cable cover (J) out from the arm. 5.2 Do the same for the rest of the cable covers before installing the cables. 5.3 Install the cables and slide the covers back to the arm. 5.4 Install the end covers. J H 6 Step 6: djusting the Display: 6.1 Slight loosen olt (); do not loosen fully or remove it, otherwise injury may occur. 6.2 Grasp the upper and lower edge of the Display, and then push or pull the Display to the desired tilt angle. 6.3 Tighten olt (). 6.4 If necessary, adjust horizon with bolts (H), as in step 4.5. FOR MORE INFORMTION VISIT ProMounts TM name, logo and model numbers are property of ProMounts. ProMounts TM

INSTALLATION INSTRUCTIONS. PLASMA TV WALL MOUNT TILT Universal (RGTU-210) WARNINGS WARNING

INSTALLATION INSTRUCTIONS. PLASMA TV WALL MOUNT TILT Universal (RGTU-210) WARNINGS WARNING PLASMA TV WALL MOUNT TILT Universal (RGTU-210) S CAUTION CAUTION CAUTION A alerts you to the possibility of serious injury or death if you do not follow the instructions. A CAUTION alerts you to the possibility