MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER

Transcription

1 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR STION 1 FLUSH INST INSTLLTION STION 2 STNR INSTLLTION FRM PNLS 3/4" OVRLY PNLS

2 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR OVRLL IMNSIONS FTR PNL INSTLL 38" (96.5) FLUSH INST INSTLLTION 25 7/8" (65.7) 20 5/8" (52.4) 10 13/16" (27.5) 7/16" (1.1) *84 1/2" (214.6) *73 5/16" (186.2) *83 1/2" (212.1) 7/16" (1.1) SPIFITIONS Overall Width Overall Height Overall epth oor learance utout Width utout Height utout epth lectrical Requirements Plumbing Requirements Shipping Weight 38" (96.5 cm) 84 1/2" (214.6 cm) 25 7/8" (49.5 cm) 19 1/2" (49.5 cm) 39" (99.1 cm) 85" (215.9 cm) 26 3/16" (66.5 cm) 115 V, 60 Hz 20 amp circuit O copper tubing or G Smartonnect kit 663 lb (300.7 kg) FRONT VIW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. **8" (20.3) 35" (89.0) ase width *26 3/8" (70.0) **8" (20.3) *4" (10.2) SI VIW *115 oor swing 19 1/2" (49.5) TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. llow 4" (10.2) min distance to adjacent wall from cutout oors can be adjusted to 90 door swing TOP VIW llow 4" (10.2) min distance to adjacent wall from cutout imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.

3 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR FLUSH INST INSTLLTION 3/4" PNLS 5 (13.3) TOP VIW Finished cleats ase Trim ase oor FLUSH INST INSTLLTION 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) epth to cleat 3/4" (1.9) Width of side cleats 3/4" 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats L. 6" (15.2) 1/2" (1.3) Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area 85" (215.9) Finished cleats W SI VIW NTI-TIP RKT 81 1/2" (207.0) 3 1/2" (8.9) 85" (215.9) Use two additional hole locations at end of brackets 4 1/16" (11.0) 7" (17.8) 10" (25.4) WTR FRONT VIW L racket mounted into vertical wall studs centered within the cutout nsure holes selected are centered on the studs Wall Studs 7" (17.8) 75 1/2" (191.8 ) From floor to bottom of electrical area 3 1/2" (8.9) WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 1/2" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions. SI VIW INSTLL WITH NTI-TIP RKT FRONT VIW OF UTOUT WITH NTI-TIP RKT

4 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR FLUSH INST 3/4" PNL IMNSIONS Grille Freezer rawer 3/4" RIS FRSH FOO OOR PNLS ROUTING 11/32" TIL TOP 3/4" 7/16" PNL IMNSIONS 38" 10 13/16" 46 7/16" 22 3/8" 18 3/4" NOT: Routed areas should be finished as they may be visible when assembled. TOP FLUSH INST INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door, drawer and grille trims. Maximum total panel weight: food door panels 30 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3 wide and stiles must be a minimum of 4 wide. oor Handles oor handles not included. ustom handles supplied by your cabinet maker may be used. ZKHF2H: uropean tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles. 3/16" TIL OTTOM ack ORNR VIW SHOWING PITUR FRM ROUTING ack WRNING: oor Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle. HING SI HNL SI ROUTR PTH ROUTR PTH 2 1/16" 3/16" LFT SI RIGHT SI ack 3/4" PNL OTTOM VIW (FTR ROUTING) OTTOM 3/4" PNL SI VIW (FTR ROUTING)

5 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR 3/4" RIS FRZR RWR PNL ROUTING 11/32" TIL LFT SI LFT SI TIL TOP 3/4" TIL OTTOM 3/4" RIS GRILL PNL ROUTING 1/2" NOT: Routed areas should be finished as they may be visible when assembled. ack ORNR VIW SHOWING PITUR FRM ROUTING ROUTR PTH ROUTR PTH 2 1/16" 2 1/16" TIL TOP ack 3/4" PNL OTTOM VIW (FTR ROUTING) NOT: Routed areas should be finished as they may be visible when assembled. TIL RIGHT SI RIGHT SI ack TOP OTTOM 3/4" PNL SI VIW (FTR ROUTING) TOP FLUSH INST INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door, drawer and grille trims. Maximum total panel weight: food door panels 30 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3 wide and stiles must be a minimum of 4 wide. oor Handles oor handles not included. ustom handles supplied by your cabinet maker may be used. ZKHF2H: uropean tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles. 1 11/16" ROUTR PTH ack ack ORNR VIW SHOWING PITUR FRM ROUTING TIL OTTOM OTTOM 3/4" PNL SI VIW (FTR ROUTING) TIL LFT SI TIL RIGHT SI ROUTR PTH ROUTR PTH 2 1/16" 2 1/16" LFT SI RIGHT SI ack 3/4" PNL OTTOM VIW (FTR ROUTING)

6 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR FLUSH INST INSTLLTION 1/2" PNLS 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 13/16" (52.9) epth to cleat Finished cleats 5 3/8" (13.7) 3/4" (1.9) Width of side cleats 85" (215.9) 4 1/16" (11.0) 1/2" Finished cleats ase Trim 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats L. 10" (25.4) ase oor 6" (15.2) 1/ (191 From to bot of elec are FLUSH INST INSTLLTION Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. W SI VIW NTI-TIP RKT 81 1/2" (207.0) 3 1/2" (8.9) Use two additional hole locations at end of brackets 7" (17.8) WTR FRONT VIW L racket mounted into vertical wall studs centered within the cutout nsure holes selected are centered on the studs Wall Studs 7" (17.8) 3 1/2" (8.9) The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 1/2" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions. SI VIW INSTLL WITH NTI-TIP RKT FRONT VIW OF UTOUT WITH NTI-TIP RKT

7 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR FLUSH INST1/2" PNL IMNSIONS Grille Freezer rawer PNL IMNSIONS KR SSMLY IMNSIONS ack Hinge Side acker with Overlay ssembly acker 33 7/8" 8 7/8" 46 1/ /8" 16 1/2".10" Space 32 1/2" 7 5/8" 44 11/16" 20 1/2" 15" 1/2" Overlay 38" 10 13/16" 46 7/16" 22 3/8" 18 3/4" ack oor acker 1/2" Overlay.10" Spacer FLUSH INST INSTLLTION The 1/2" overlay panel must be secured to a.10" spacer panel and a thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel. Maximum total panel weight: food door panel 30 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs. Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3 wide and stiles must be a minimum of 4 wide. WRNING: oor Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle. Freezer rawer Grille ack PNL IMNSIONS oor s 2 1/16" 3/16" 3/16" 3/16" Freezer rawer 2 1/16" 2 1/16" Grille 2 1/16" 2 1/16" 1 11/16"

8 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR OVRLL IMNSIONS FTR PNL INSTLL STNR INSTLLTION 25 3/8" (64.5) 36" (91.4) 23 13/16" (60.5) 9 7/8" (25.1) 1 5/8" (4.1) 9/16" (1.4) *84" (213.4) 46 5/16" (117.7) *73 (186.1) *83 1/2" (212.1) 1/2" (1.3) SPIFITIONS *26 7/16" (67.1) Overall Width 36" (91.4 cm) Overall Height 84" (213.4 cm) Overall epth oor learance 25 3/8" (64.5 cm) 18 3/16" (46.2 cm) FRONT VIW *4 1/8" (10.5) SI VIW utout Width utout Height utout epth 35 1/2" (90.2 cm) 84" (213.4 cm) 24" (61 cm) * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. lectrical Requirements 115 V, 60 Hz 20 amp circuit Plumbing Requirements O copper tubing or G Smartonnect kit 35" (89.0) ase width Shipping Weight 614 lb TTNTION LTRIIN: **12 7/8" (32.7) **12 7/8" (32.7) 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. **130 oor swing oors can be adjusted to 90 door swing 18 3/16" (46.2) llow 4" (10.2) min distance to adjacent wall from cutout TOP VIW (SHOWING OOR SWING) llow 4" (10.2) min distance to adjacent wall from cutout imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.

9 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR STNR INSTLLTION 3/4" PNLS STNR INSTLLTION TOP VIW 3 1/8" 24" (61) (7.93) 35 1/2" (90.2) 7/16" (1.1) 1 9/16" Trim overlap 2 5/16" (3.97) (5.874) L. 6" (15.24) Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area *84" (213.4) *Trim will overlap additional 7/16" 10" (25.4) 75" (190.5 ) From floor to bottom of electrical area WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. SI VIW W NTI-TIP RKT 3 1/2" (8.9) 81 1/2" (207.0) Use two additional hole locations at end of brackets 5" (12.7) WTR FRONT VIW L racket mounted into vertical wall studs centered within the cutout nsure holes selected are centered on the studs Wall Studs 5" (12.7) 3 1/2" (8.9) The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81-1/2" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions. SI VIW INSTLL WITH NTI-TIP RKT FRONT VIW OF UTOUT WITH NTI-TIP RKT

10 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR STNR FRM PNL IMNSIONS Grille PNL SSMLY ROSS STION Trim oor Framed Supplied Handles STNR INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required. Framed s: For thick custom panels ordered from your cabinet maker. The decorative panels slide into this trim. Freezer rawer PNL IMNSIONS Framed 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2" Maximum total panel weight: food door panel 30 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs oor Handles: The supplied handles accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed..

11 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR STNR 3/4" OVRLY PNL IMNSIONS Grille Freezer rawer PNL SSMLY ROSS STION Trim acker.10" Spacer PNL IMNSIONS KR SSMLY IMNSIONS ack Hinge Side acker with Overlay ssembly oor 3/4" Overlay Supplied Handles Framed 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2".10" Framed 32 1/2" 7 5/8" 44 11/16" 20 1/2" 15" 3/4" Overlay 34 1/8" 9" 46 5/16" 22" 16 5/8".25" +.10" +.75" = 1.10" Total Thickness ack oor acker 1/2" Overlay.10" Spacer STNR INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required. 3/4" Overlay s: For your 3/4" thick custom panels ordered from your cabinet maker the overlay panel must be secured to a -thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOT: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: food door panel 30 lbs. Freezer drawer panel 28 lbs. Grille panel 11 lbs oor Handles: The supplied handles accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHF2H: uropean tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles. Freezer rawer Grille ack PNL IMNSIONS oor s 1/8" 0 1/8" 1/8" Freezer rawer 1/8" 1/8" 1/16" 1/16" Grille 1/8" 1/8" 1/16" 1/16"

12 MONOGRM 36" UILT-IN FRNH-OOR OTTOM-FRZR FTURS N NFITS FRNH-OOR design gives your wide-open access to every fresh food shelf and bin. FINLY RFT GLSS-FRONT MTL OOR INS WITH RIVT MTL NTS offer easy access to beverages and quick-grab items. L LIGHTING positioned throughout the interior and under fresh food drawers spotlights food inside the refrigerator and in the freezer. UPFRONT LTRONI ONTROLS WITH IGITL ROUT Offer a range of precise temperature settings, all within easy reach. LRG FULL-XTNSION FRZR RWR has storage bins that slide out independently of one another for easy loading and unloading. n automatic icemaker keeps plenty of filtered ice on hand. PRISION GLSS-FRONT PROU N LI RWRS Feature full-extension, soft-close slides. LUMINUM TRIMM GLSS SHLVS llow convenient access to contents in the fresh-food compartment.