STOP! Call Us First! DO NOT RETURN TO STORE.

Transcription

1 1656 STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: or Our staff is ready to provide assistance April through October M-F 8:00 AM to 4:30 PM EST Saturday 8:30 AM to 4:30 PM EST November through March M - F 8:00 AM to 5:00 PM EST

2 (This page intentionally left blank.)

3 A Backyard Products Company ASSEMBLY MANUAL OAKRIDGE 8' x 1' (44 x 366 cm) ACTUAL FLOOR SIZE IS 96 x 140-5/8" (43,8 x 357, cm) KEEP THIS MANUAL FOR FUTURE REFERENCE Window Location Optional IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO NING ASSEMBLY. BEFORE YOU BUILDING RESTRICTIONS AND APPROVALS Be sure to check with local building department and homeowners association for specific restrictions and/ or requirements before building. ENGINEERED DRAWINGS Contact our Customer Service Team if engineered drawings are needed to pull local permits. SURFACE PREPARATION To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are listed on page 7. CHECK ALL PARTS Inventory all parts listed on pages 4-6. Contact our Customer Service Team if any parts are missing or damaged. ADDITIONAL MATERIALS You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities. - CUSTOMER SERVICE - Call: customerservice@backyardproductsllc.com

4 TOOLS Phillips Screwdriver Drill / Driver 1/8" Drill Bit 1/4" Drill Bit 5/16" Drill Bit 1/" Drill Bit # Philips Drive Bit Hammer Level Pencil Tape Measure Required Utility Knife Shingle Blades Caulk Gun Paint Tools Safety Glasses Ladder Tool Belt/ Nail Pouch Gloves Optional Tin Snips (for drip edge) Chalk Line Nail Gun gun nails Square or Safety! Always use approved safety glasses during assembly. HELPFUL REMINDER SYMBOLS Look for these symbols for helpful reminders throughout this manual. = Assistance Required; two or more people. = Mark part with pencil. = Ensure squareness. = Beginning of steps for assembly or installation. = Important required step or operation. = You have finished the assembly or installation. = Helpful assembly hint. = Level ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side. Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product. (See Fig. A, B, C.) A B C

5 ADDITIONAL MATERIALS This shed kit includes a complete wood floor system. This shed kit does not include ANY leveling materials. FOUNDATION OR FLOOR MATERIALS See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. COMPLETING YOUR SHED You will need these additional materials: 3-TAB SHINGLES... 7 Bundles PAINT FOR SIDING... Gallons Use 100% acrylic latex exterior paint. () coats recommended. CAULK... 3 Tubes Use acrylic latex exterior caulk that is paintable. 1" GALVANIZED ROOFING NAILS... 3 Lbs For shingles. PAINT FOR TRIM...1 Quart Use 100% acrylic latex exterior paint. WOOD GLUE... Exterior Rated OPTIONAL MATERIALS DRIP EDGE Feet #15 ROOFING FELT To cover 148 Sq. Ft. of roof area. 1" GALVANIZED ROOFING NAILS...1/4 Lb For roofing felt. REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER S INSTRUCTIONS FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT. 3

6 Part identification letters are stamped on some parts. RS RS Check these locations for part stamp. PARTS IDENTIFICATION AND SIZES Treated lumber is stamped: PARTS LIST INVENTORY YOUR PARTS before you begin. We suggest sorting parts by the category they are listed in. WOOD SIZE CONVERSION CHART Nominal Board Size Actual Size " x 4"...1-1/" x 3-1/" (3,8 x 8,9 cm) 1" x 4"...3/4" x 3-1/" (1,9 x 8,9 cm) " x 3"...1-1/" x -1/" (3,8 x 6,3 cm) 1" x 3"...3/4" x -1/" (3,8 x 6,3 cm) 19/3" x 3"...19/3" x -1/" (1,5 x 6,3 cm) FLOOR 0 x 4 x 48" (5,1 x 10, x 11,9 cm) x 4 x 9-5/8" (5,1 x 10, x 35,3 cm) x 4 x 93" (5,1 x 10, x 36, cm) All treated lumber is stamped: WALLS 6 x4 x4 x4 GAA XTA PWA DQ CWA RD CXA AO XY RZ SP UM YF TM FW SZ 1 x 3 x 5" (,5 x 7,6 x 1,7 cm) Gauge Block for 3/4" (1,9 cm) measurement x 4 x 4-5/8" (5,1 x 10, x 11,7 cm) 3/8 x x 5" (1,0 x 5,1 x 1,7 cm) x 4 x 10" (5,1 x 10, x 5,4 cm) x 3 x 11-7/8" (5,1 x 7,6 x 30, cm) x 4 x 13" (5,1 x 10, x 33,0 cm) x 4 x 16-1/" (5,1 x 10, x 41,9 cm) x 4 x 17-3/4" (5,1 x 10, x 45,1 cm) x 4 x -1/" (5,1 x 10, x 57, cm) x 4 x 34-1/4" (5,1 x 10, x 87,0 cm) x 4 x 35-3/4" (5,1 x 10, x 90,8 cm) x 4 x 48" (5,1 x 10, x 11,9 cm) x 4 x 68" (5,1 x 10,3 x 17,7 cm) x 4 x 68-5/8" (5,1 x 10, x 174,3 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) x 3 x 84" (5,1 x 7,6 x 13,4 cm) x 4 x 89" (5,1 x 10, x 6,1 cm) 96" (43,8 cm) Z-STRIP 3/4" (1,9 cm) RAFTERS 1 YJ WW SP 7-1/4 x 18-1/4" (18,4 x 46,4 cm) OSB OR WOOD GRAIN x 4 x 68-7/16" (5,1 x 10, x 173,8 cm) x 4 x 69-7/8" (5,1 x 10, x 177,5 cm) x 4 x 48" (5,1 x 10, x 11,9 cm) WMR WML 19/3 x 4 x 69-7/8" (1,5 x 10, x 177,5 cm) 19/3 x 4 x 69-7/8" (1,5 x 10, x 177,5 cm) 3/8 x -3/4 x 80-1/4" (1 x 7 x 03,8 cm) TRIM x8 x4 x6 CCR EU DLA AZ 19/3 x 3 x 7-1/" (1,5 x 7,6 x 19,1 cm) 19/3 x 3 x 17" (1,5 x 7,6 x 43,1 cm) 19/3 x 3 x 30" (1,5 x 7,6 x 76, cm) 19/3 x 3 x 30-1/8" (1,5 x 7,6 x 76,5 cm) 3/8 x -3/4 x 69" (1 x 7 x 175,3 cm) 3/8 x 1-3/4 x 67-3/4" (1 x 4,4 x 17,1 cm) 4 EFA ROR 19/3 x 3 x 11-1/" (1,5 x 7,6 x 7,9 cm) 19/3 x 3 x 8-1/" (1,5 x 7,6 x 7,9 cm) DKA 19/3 x 3 x 44-1/8" (1,5 x 7,6 x 11,1 cm) DNA 19/3 x 3 x 64-7/16" (1,5 x 7,6 x 163,7 cm)

7 PARTS LIST continued... SHELF WJ PL x 3 x 18-3/8" (5,1 x 7,6 x 50, cm) x 3 x 93" (5,1 x 7,6 x 36, cm) LOFT BENCH x3 TP UN x 4 x 96" (5,1 x 10, x 43,8 cm) x 4 x 94-1/" (5,1 x 10, x 40 cm) 7-1/4 x 18-1/4" (18,4 x 46,4 cm) WITH WOOD GRAIN ON FACE OVERHANG x4 x4 WE DY 19/3 x 6-15/16 x 5-1/" (1,5 x 17,6 x 13,4 cm) 19/3 x 6-15/16 x 5-1/" (1,5 x 17,6 x 13,4 cm) x 3 x 68-7/16" (5,1 x 7,6 x 173,8 cm) x 3 x 7-7/8" (5,1 x 7,6 x 0 cm) 3/8 x 7-7/8 x 57-7/8" (1 x 0 x 147 cm) 3/8 x 7-7/8 x 7-7/8" (1 x 0 x 0 cm) 3/8 x 5-13/16 x 7-7/8" (1 x 14,8 x 0 cm) WD x 3 x 5-1/8" (5,1 x 7,6 x 13 cm) SOFFIT WS ZM 1 x x 43-1/" (,5 x 5,1 x 110,5 cm) 1 x x 96" (,5 x 5,1 x 43,8 cm) 3/8 x 5-3/16 x 69-3/8" (1 x 13, x 176, cm) DOOR x4 GI OO Roof panels are 7/16" (1,1 cm) thick. 3/8 x 5-3/16 x 7" (1 x 13, x 18,9 cm) 19/3 x 3 x 3" (1,5 x 7,6 x 58,4 cm) 1-1/4 x -1/ x 69" (3, x 6,3 x 175,3 cm) PANEL PARTS LIST Shelf / Loft panels are 7/16" (1,1 cm) thick. ROOF PANELS 7/16 x 8-7/8 x 70" (1,1 x,5 x 177,8 cm) 7/16 x x 46-1/" (1,1 x 55,9 x 118,1 cm) 7/16 x 47-7/8 x 48" (1,1 x 11,6 x 11,9 cm) 7/16 x x 96" (1,1 x 55,9 x 43,8 cm) 7/16 x 48 x 94-1/" (1,1 x 11,9 x 40 cm) SHELF, LOFT & BENCH Floor panels are 5/8" (1,6 cm) thick. FLOOR 7/16 x 35-7/8 x 8" (1,1 x 91,1 x 31,1 cm) 7/16 x 3-7/8 x 88-7/8" (1,1 x 60,6 x 6,1 cm) 7/16 x 11-7/8 x 88-7/8" (1,1 x 30, x 6,1 cm) 5/8 x 48 x 96" (1,6 x 11,9 x 43,8 cm) 5/8 x 44-5/8 x 96" (1,6 x 113,3 x 43,8 cm) NOTE: Panel parts are not stamped. 5

8 WALL PANEL & DOORS PARTS LIST x6 3/8 x 48 x 7" (1 x 11,9 x 18,9 cm) 3/8 x 44-5/8 x 7" (1 x 113,3 x 18,9 cm) LEFT DOOR RIGHT DOOR 3/8 x 19-5/8 x 7" (1 x 49,8 x 18,9 cm) NAIL BOXES x3 BOXES x6 BOXES " (5,1 cm) x90 75 x96 x7 4 x64 x60 FASTENER/HARDWARE BAG 1-1/" (3,8 cm) " (5,1 cm) -1/" (6,4 cm) " (5,0 cm) 1-1/4" (3, cm) 3/4" (1,9 cm) 1/" (1,3 cm) VENT, DOOR HARDWARE, AND WINDOW x4 8 x 16" (0,3 x 35,6 cm) x8 1" (,5 cm) 1-1/" (3,8 cm) 3/4" (1,9 cm) Transom Window 56" Metal Threshold 3/4" (1,9 cm) 8 Bagged seperately / special coating 6 Large Window Gable Window

9 FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS 3" Screws angled into 4x4. () at each point frame and 4x4 touch. 1" (30,5 cm) MATERIAL REQUIRED D O O R Measurements to centers of 4x4's. 4" x 4" x 1' (10 x 10 x 366 cm)treated Lumber 1" (30,5 cm) Fasteners for Frame to 4"x 4". (3" Screws shown as one option.) Minimum (40) 3" screws / exterior grade. Use only wood treated for ground contact and fasteners approved for use with treated wood. Always support frame seams. 1" Maximum between leveling material locations. 48" Shingle Level 4x4 Runner 1" Shingle Gravel " Block Gravel 4" Block LEVELING METHODS x4 Treated Lumber 8" Block Level under 4x4 runners only. Locate leveling material 1" from ends of runners and no more than 48" apart. Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use shingles in direct contact with ground. For best results and aiding in water drainage use gravel under each concrete block. LEVELING MATERIALS Gravel Solid Masonry Blocks in 1", ", 4" or 8" thickness x4 Treated Lumber Asphalt Shingles Leveling higher than 16" not recommended. CONCRETE If you are building your shed on a concrete foundation see the following page. 7 Do not exceed 16".

10 CONCRETE FOUNDATION Your kit contains all materials to construct a wooden floor. If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C B 3-1/" (8,9 cm) 4" (10, cm) A DOOR Building Size 8'x 1' (43,8 x 365,8 cm) Requires: Allow new concrete slabs to cure for at least seven (7) days. A treated x 4" (5,1 x 10, cm) sill plate is required when installing your shed on concrete. Hint: Use treated lumber in your kit or purchase full length treated lumber. Use a high quality exterior grade caulk beneath all sill plates. Fasten x 4" (5,1 x 10, cm) sill plates to slab using approved concrete anchors (fasteners not included). Check local code for concrete foundation requirements. 96" x 140-5/8" (43,8 x 357, cm) 96" (43,8 cm) 133-5/8" (339,4 cm) " x 4" x 11'-1-5/8" (5,1 x 10, x 339,4 cm) " x 4" x 8' (5,1 x 10, x 44 cm) Caulk Actual Size A B C NOTES MUST be treated lumber. MUST be treated lumber /8" (357, cm) 8

11 PARTS REQUIRED: 0 x 4 x 9-5/8" (5,1 x 10, x 35,3 cm) x 4 x 93" (5,1 x 10, x 36, cm) x 4 x 48" (5,1 x 10, x 11,9 cm) 1 FLOOR FRAME Orient parts as shown on flat surface. Measure and mark. Use two 3" nails at each mark. 3 You have finished your floor frame. Proceed to level and square frame. x44 Look for TREATED Stamp HINT: For easier nailing stand on frame. 16" (40,7 cm) 48" (11,9 cm) 16" (40,7 cm) 16" (40,7 cm) 1-5/8" (3,1 cm) 140-5/8" (357, cm) 14-5/8" (316,6 cm) 108-5/8" (75,9 cm) 9-5/8" (43,8 cm) 80" (03, cm) 64" (11,9 cm) 48" (11,9 cm) 3" (81,3 cm) 16" (40,7 cm) Offset Seam Note this measurement Center on marks 96" (43,8 cm) 93" (36, cm) DOOR Offset Seam 9-5/8 (35,3 cm) 9 48" (11,9 cm)

12 LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. 1 See page 7 for the preferred floor leveling method. 3 4 Use level and check the frame is level before applying floor panels. Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square. The diagonal measurement will be approximately 170-1/4" (43,4 cm). When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one fastener at ends of each runner making sure the frame remains square (Fig. A). 5 Once the floor frame is level and square fasten the frame to the 4x4 runners at each point the frame contacts the 4x4 runners. First, secure at ends with one fastener. Fig. A 170-1/4" (43,4 cm) 170-1/4" (43,4 cm) DOOR Second, secure at ends with one fastener. 10

13 FLOOR PANELS PARTS REQUIRED: x6 " (5,1 cm) 5/8 x 48 x 96" (1,6 x 11,9 x 43,8 cm) 1 Ensure your floor frame is square by installing one panel and squaring frame. Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with two " nails in the corners. Move to the opposite side. Using the long edge of the panel as a lever, move the panel side-to-side until the top corner is flush to the floor frame (Fig. B). Secure panel with two " nails in the corners. 3 Check the floor frame is square by measuring diagonally across the frame corners. If the measurements are the same your floor frame is square. The measurement will be approximately 170-1/4" (43,4 cm) (Fig. C). 4 Continue attaching the panel using " nails 6" apart on edges and 1" apart inside panel. Use a chalk line or use pre-painted grid lines to nail into joists under panel. Seam 6" (15, cm) 3/4" (1,9 cm) Grid lines up 1" (30, cm) Fig. A () Nails DOOR DOOR () Nails Seam 140-5/8" (35, cm) 48" (11,9 cm) Fig. B 170-1/4" (43,4 cm 170-1/4" (43,4 cm DOOR 11 Fig. C

14 FLOOR PANELS PARTS REQUIRED: 4 " (5,1 cm) 5/8 x 48 x 96" (1,6 x 11,9 x 43,8 cm) 5/8 x 44-5/8 x 96" (1,6 x 113,3 x 43,8 cm) Continue installing panels with rough side up (painted grid lines). Position 44-5/8" panel in middle of floor frame. Use grid lines on panel for " nails 6" apart on edges, and 1" apart inside panels. 7 You have finished attaching your floor panels. 48" (11,9 cm) 140-5/8" (357, cm) 44-5/8" (113,3 cm) 1-5/8" (3,1 cm) 3" (81,3 cm) Grid lines up DOOR 1" (30,5 cm) 6" (15, cm) 1

15 IMPORTANT! Check the floor frame is level after installing floor panels. Re-level if needed. DOOR The floor should be used as a stable work surface for wall construction. HINT: Organize your assembly procedure during the build process to avoid over-handling of the walls. Back wall Right Wall Left wall (Your window location will be determined later during assembly.) Front wall 13

16 PARTS REQUIRED: x7 UM YF TM LEFT WALL FRAME x3 x 4 x 68" (5,1 x 10, x 17,7 cm) x 4 x 68-5/8" (5,1 x 10, x 174,3 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) 1 YOU MUST BUILD THE LEFT AND RIGHT SIDE WALLS EXACTLY AS SHOWN! YOU WILL ASSEMBLE ONE LEFT AND ONE RIGHT WALL SEPARATELY. For left wall, orient parts on edge on floor. Measure and mark. HINT: For easier nailing stand on frame. Use two 3" nails at each mark and four 3" nails at seams 140-5/8 (35,7cm) 0-5/8 (5,4 cm) IMPORTANT MEASUREMENT 10 (304,8 cm) 96 (43,8 cm) 7 (18,9 cm) 48 (11,9 cm) 4 (61 cm) YF TOENAILING 1-1/ (3,8 cm) TM UM x7 68 (17,7 cm) 1-1/ (3,8 cm) DOOR YF 1-1/ (3,8 cm) TM 68-5/8 (174,3 cm) 14 7 (18,9 cm)

17 LEFT SIDE WALL PANELS PARTS REQUIRED: x45 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 3/4" GAUGE BLOCK YOU WILL ASSEMBLE ONE LEFT AND ONE RIGHT WALL SEPARATELY. Ensure your wall frame is square by installing one panel and squaring frame. 3 Place 48 x 7" panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with two " nails in the corners (Fig. A). 4 5 Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have a 3/4" measurement on the wall stud. Secure corner with two " nails (Fig. B). Nail the panel using " nails 6" apart on edges and 1" apart inside panel. Nails 3/4" (1,9 cm) 3/4" (1,9 cm) Fig. A Fig. B Nails HERE 0-5/8" (5,4 cm) For squareness maintain and 3/4" measurement along panel edges. 3/4" (1,9 cm) 1" (30,5 cm) 6" (15, cm) Primed side up DOOR 3/4" GAUGE BLOCK 3/4" 48" (1,9 cm) (11,9 cm) ( 15

18 PARTS REQUIRED: LEFT SIDE WALL PANELS x90 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 44-5/8 x 7" (11,9 x 13,4 cm) 3/4" GAUGE BLOCK For squareness maintain flush and 3/4" measurement along panel edges. 6 Place center 48" x 7" panel on frame as shown with primed side facing up. Nail using " nails 6" apart on edges and 1" apart inside panel. 3/4" (1,9 cm) 1" (30,5 cm) Primed side up 3/4" GAUGE BLOCK 6" (15, cm) DOOR 7 Place end 44-5/8" x 7" panel on frame as shown with primed side facing up. Nail using " nails 6" apart on edges and 1" apart inside panel. 48" (11,9 cm) For squareness maintain flush along panel edges. 1" (30,5 cm) 6" (15, cm) DOOR 8 Carefully flip the LEFT wall over. 44-5/8" (113,3 cm) Primed side up 9 You have finished building your LEFT WALL. 16

19 PARTS REQUIRED: x7 UM YF TM RIGHT WALL FRAME x3 x 4 x 68" (5,1 x 10, x 17,7 cm) x 4 x 68-5/8" (5,1 x 10, x 174,3 cm) x 4 x 7" (5,1 x 10, x 18,9 cm) 1 For right wall, orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark and four 3" nails at seams HINT: For easier nailing stand on frame. 96 (43,8 cm) 10 (304,8 cm) 140-5/8 (35,7cm) 4 (61 cm) 48 (11,9 cm) 7 (18,9 cm) 0-5/8 (5,4 cm) IMPORTANT MEASUREMENT 1-1/ (3,8 cm) TM TOENAILING YF DOOR 1-1/ (3,8 cm) 68 (17,7 cm) UM x7 1-1/ (3,8 cm) TM YF 7 (18,9 cm) 68-5/8 (174,3 cm) 17

20 PARTS REQUIRED: RIGHT SIDE WALL PANELS x45 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 3/4" GAUGE BLOCK Ensure your wall frame is square by installing one panel and squaring frame. 3 Place 48 x 7" panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with two " nails in the corners (Fig. A). 4 5 Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have a 3/4" measurement on the wall stud. Secure corner with two " nails (Fig. B). Nail the panel using " nails 6" apart on edges and 1" apart inside panel. Nails 3/4" (1,9 cm) 3/4" (1,9 cm) Fig. A 3/4" (1,9 cm) Nails Fig. B HERE For squareness maintain flush and 3/4" measurement along panel edges. 0-5/8" (5,4 cm) 6" (15, cm) 1" (30,5 cm) DOOR Primed side up 3/4" GAUGE BLOCK m) 48" (11,9 cm) 3/4" (1,9 cm) 18

21 PARTS REQUIRED: RIGHT SIDE WALL PANELS x90 " (5,1 cm) 48 x 7" (11,9 x 13,4 cm) 44-5/8 x 7" (11,9 x 13,4 cm) 3/4" GAUGE BLOCK For squareness maintain flush and 3/4" measurement along panel edges. 6 Place center 48" x 7" panel on frame as shown with primed side facing up. Nail using " nails 6" apart on edges and 1" apart inside panel. 1" (30,5 cm) 3/4" (1,9 cm) 3/4" GAUGE BLOCK DOOR 6" (15, cm) Primed side up 7 Place end 44-5/8" x 7" panel on frame as shown with primed side facing up. Nail using " nails 6" apart on edges and 1" apart inside panel. 48" (11,9 cm) For squareness maintain flush along panel edges. DOOR 1" (30,5 cm) 6" (15, cm) 8 Carefully flip the RIGHT wall over. Primed side up 44-5/8" (113,3 cm) 9 You have finished building both of your sidewalls. 19

22 PARTS REQUIRED: CWA x 4 x 13" (5,1 x 10, x 33 cm) CXA x 4 x 17-3/4" (5 x 10, x 45,1 cm) x3 BACK WALL FRAME x6 XY x 4 x 34-1/4" (5 x 10, x 87 cm) SZ x 4 x 89" (5 x 10, x 6,1 cm) 1 Orient XY, CWA, CXA and SZ's on edge on floor as shown. Secure using two 3" nails at each connection. 89" (6,1 cm) 44-1/" (113,1 cm) 44-1/" (113,1 cm) SZ () Nails 1-1/" (3,8 cm) 13" (33 cm) 1-1/" (3,8 cm) 44-1/" (113,1 cm) CWA 89" (6,1 cm) 44-1/" (113,1 cm) SZ () Nails 1-1/" (3,8 cm) 17-3/4" (45,1 cm) 1-1/" (3,8 cm) 44-1/" (113,1 cm) CXA 89" (6,1 cm) 44-1/" (113,1 cm) SZ () Nails 1-1/" (3,8 cm) XY 34-1/4" (87 cm) 1-1/" (3,8 cm) 0

23 BACK WALL PANELS PARTS REQUIRED: 6 " (5,1 cm) 3/8 x 48 x 7" (1 x 11,9 x 18,9 cm) 3/4" GAUGE BLOCK 3 Place panel with primed side up onto frames with a 3/4" gap as shown. Maintain flush to top of frame edge. 4 Ensure 3/4" gap between top, middle and bottom of frames. Hold the measurements and secure with " (5,1 cm) nails 6" (15, cm) apart. 3-1/" (8,9 cm) 6" (15, cm) CWA 15-1/4" (38,7 cm) 1" (30,5 cm) 3/4" (1,9 cm) Use Gauge Block As Spacer 3/4" (1,9 cm) 35-1/4" (89,5 cm) 3-1/" (8,9 cm) 3/4" (1,9 cm) CXA Use Gauge Block As Spacer 3/4" (1,9 cm) XY 3/4" (1,9 cm) GAA 3/4" GAUGE BLOCK Primed side up 1

24 PARTS REQUIRED: BACK WALL PANELS 6 " (5,1 cm) 3/8 x 48 x 7" (1 x 11,9 x 18,9 cm) 6 Place right panel flush to left panel with primed side up. Secure using " (5,1 cm) nails 6" (15, cm) apart on edges and 1" (30,5 cm) apart on inside of panel. 7 You have finished installing your back wall panels. 6" (15, cm) 1" (30,5 cm) 15-1/4" (38,7 cm) 35-1/4" (89,5 cm) 6" (15, cm)

25 PARTS REQUIRED: BACK WALL x8 UN x 4 x 94-1/" (5,1 x 10, x 40 cm) 1 Center UN on back wall top plate and flush to inside of back of wall panel (Fig. A). While keeping UN flush, secure to top plate using eight 3" screws. UN UN CENTER ON TOP PLATE Fig. A Screws Screws INSIDE OF SHED 3

26 PARTS REQUIRED: RD x 4 x 16-1/" (5,1 x 10, x 41,9 cm) UM x 4 x 68" (5,1 x 10, x 17,7 cm) SZ x 4 x 89" (5 x 10, x 6,1 cm) FRONT WALL x8 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. HINT: For easier nailing stand on frame. 16-1/" (41,9 cm) 89" (6,1 cm) 56" (14,3 cm) 16-1/" (41,9 cm) SZ 68" (17,7 cm) Nails 56" (14,3 cm) 68" (17,7 cm) UM UM RD RD 16-1/" (41,9 cm) /" (41,9 cm)

27 PARTS REQUIRED: FRONT WALL OO 1-1/4 x -1/ x 69" (3, x 6,3 x 175,3 cm) TEMPORARY SUPPORT 3/8 x 19-5/8 x 7" (1 x 49,8 x 18,9 cm) x40 " (5,1 cm) 3 Place 19-5/8" x 7" panel onto wall frame flush to SZ with primed side up as shown. Secure panel with two " nails 6" (15, cm) apart. 4 5 Repeat step 3 to attach the remaining panel. Use OO as a brace to maintain 56" (14,3 cm) opening. Use two 3" screws to attach. 19-5/8" (49,8 cm) For squareness maintain flush along panel edges. 19-5/8" (49,8 cm) 6" (15, cm) 6" (15, cm) 7" (18,9 cm) 7" (18,9 cm) Maintain Maintain 56" dimension 56" (14,3 cm) Install OO after panels for temporary brace. Maintain Primed side up Primed side up 5

28 PARTS REQUIRED: FW x 3 x 84" (5,1 x 7,6 x 13,4 cm) FRONT WALL x5 6 7 Center FW on the -1/" side of SZ flush to edge (Fig. A, B). Secure using five 3" screws on angle spaced evenly. 8 You have finished building your front wall. Fig. A Fig. B FW to x4 UM FW SZ FW Front wall panel Front wall panel CENTER CENTER NOTE: Drive screws at an angle to avoid screw points protruding into the door opening. 6

29 RIGHT SIDE WALL INSTALLATION PARTS REQUIRED (TEMPORARY): UN x 4 x 94-1/" (5,1 x 10, x 40 cm) 5 " (5,1 cm) Stand right sidewall on floor. It is important to secure the right sidewall in the following order. ENSURE 0-5/8" MEASUREMENT IS TOWARD BACK OF SHED 1 Center right sidewall assembly on the 140-5/8" (357, cm) floor dimension. Use UN as a temporary brace. Secure with two 3" screws. Panel 0-5/8" (5,4 cm) UN 140-5/8" (357, cm) DOOR Screws 3 4 First, nail lower edge of panel to floor frame using " nails 6" apart. Angle nail to hit floor frame (Fig. A). Secure side wall bottom plates to floor using 3" nails (Fig. A). Nails Nail " nails first. " (5,1 cm) Nails Fig. A 3" Nails into bottom plate. 5 You have finished standing your right side wall. DOOR Screw 7

30 PARTS REQUIRED (TEMPORARY): UN x 4 x 94-1/" (5,1 x 10, x 40 cm) LEFT SIDE WALL INSTALLATION 5 Stand left sidewall on floor. It is important to secure the left sidewall in the following order. ENSURE 0-5/8" MEASUREMENT IS TOWARD BACK OF SHED. 1 Center left sidewall assembly on the 140-5/8" (357, cm) floor dimension. " (5,1 cm) Use UN as a temporary brace. Secure with two 3" screws. Panel 140-5/8" (357, cm) 0-5/8" (5,4 cm) Screws DOOR 3 4 First, nail lower edge of panel to floor frame using " nails 6" apart. Angle nail to hit floor frame (Fig. A). Secure side wall bottom plates to floor using 3" nails (Fig. A). UN 3" Nails into bottom plate. Nail " nails first. " (5,1 cm) Nails Nails DOOR Fig. A 5 You have finished standing your left side wall. Screw 8

31 PARTS REQUIRED: BACK WALL INSTALLATION 4 7 " (5,1 cm) 6 1-1/" (3,8 cm) Stand back wall on floor. It is important to secure the back wall in the following order. 1 Set back wall on side wall top plates and secure using two 3" screws on each side (Fig A). BE SURE TOP PLATES ARE FLUSH. Nail lower edge of panel to floor using " nails 6" apart. Angle nail to hit floor frame (Fig. B). ENSURE WALL IS CENTERED ON FLOOR BEFORE NAILING Secure back wall upright to floor using two 3" screws (Fig. C). Nail back wall panel to side wall stud using 1-1/" nails at 6" apart. Secure the two back wall center horizontal x 3" shelf supports using two 3" screws into back wall frame at an angle as shown (Fig. D). 6 You have finished standing your back wall. () Screws () Screws Fig. A Fig. D 6" (15, cm) 1-1/" (3,8 cm) Nails Nail " nails first. 1-1/" (3,8 cm) Nails " (5,1 cm) Nail Fig. B " (5,1 cm) Nails () Screws DOOR Fig. C 9

32 PARTS REQUIRED: x8 6 FRONT WALL INSTALLATION " (5,1 cm) x8 1-1/" (3,8 cm) Stand front wall on floor. It is important to secure the frontwall in the following order. 1 Center front wall on floor side-to-side Secure top plate to side walls using two 3" nails (Fig. A, B, E ). Nail front wall panels to side wall using 1-1/" nails 6" apart (Fig. D). Secure lower edge of panel to floor frame using eight " nails 6" apart Angle nail to hit floor frame (Fig. C). Secure bottom plates with three 3" nails on each side (Fig. C). 6 Fig. E Secure top plate to side walls using two 3" screws (Fig. A, B). Remove temporary brace OO. Nail () Nails 1-1/" (3,8 cm) Nails () Screws Fig. D Fig. A Fig. B Center wall assembly on floor. Nails Nail " nails first. Angle nail to hit floor frame. " (5,1 cm) Nails Fig. C Maintain 56" dimension 7 You have finished standing your front wall. 30 Nails

33 PARTS REQUIRED: 1 OSB OR WOOD GRAIN 7-1/4 x 18-1/4" (18,4 x 46,4 cm) YJ x 4 x 68-7/16" (5,1 x 10, x 173,8 cm) RAFTERS 3 DY x 3 x 7-7/8" (5,1 x 7,6 0 cm) TEMPORARY SUPPORT " (5,1 cm) 1 Place one DY against back wall inner panel as shown. Position and square other DY as temporary jig using two screws as shown. You will build SIX assemblies. (5) with two gussets, and (1) with one gusset. Place two rafter halves (YJ) in the corner of back and side wall and DY. Rafters contact at peak. HINT: Use floor and walls to help assemble rafters! 107-1/8" (7,1 cm) Fit base of Rafters in corners of back wall and jig. Back Wall Temporary support DY YJ YJ Temporary support DY Contact at peak Apply glue to rafters where gusset will fit. NOTE: BE SURE TO SET ASIDE ONE GUSSET WITH ED WOOD GRAIN PATTERN. Secure gusset to rafters using twelve " (5,1 cm) Nails as shown. Flip over rafter assembly and repeat STEPS -4 to attach second gusset to other side. SET ONE RAFTER ASSEMBLY ASIDE WITH ONLY ONE GUSSET ATTACHED. Repeat STEPS -4 to build three additional rafter assemblies. Remove DY. 6 You have finished assembling your rafters. Gusset Center Glue " (5,1 cm) Nails (1) per side Glue 31

34 RAFTERS PARTS REQUIRED: x5 4 Preassembled (1) GUSSET Preassembled 1 Locate first (1) GUSSET rafter directly over front stud, flush to inside of front wall panels, and tight to side wall (Fig. A, B). Face gusset inward. Rest notch on top plate. Secure rafter to top plate with two 3" screws above notch (Fig. A, B). Place remaining rafters on top plate, aligned over studs as shown and secure with 3" screws (Fig. B). 3 You have finished attaching your rafters. 4" (61 cm) 4" (61 cm) Rafter with ONE GUSSET facing inward. 4" (61 cm) 4" (61 cm) 3-1/4" (59 cm) MEASUREMENTS ARE TO CENTER OF RAFTER Align over studs. DOOR () Screws () Screws to inside of panel. Tight to side wall Fig. B 3 Fig. A

35 PARTS REQUIRED: XTA x 4 x 4-5/8" (5,1 x 10, x 11,7 cm) PWA x 3 x 10" (5,1 x 7,6 x 5,4 cm) DQ FRONT WALL GABLE x 3 x 11-7/8" (5,1 x 7,6 x 30, cm) 8 WJ x 3 x 18-3/8" (5,1 x 7,6 x 50, cm) TEMPORARY SUPPORT 1-1/" (3,8 cm) 1 Orient parts on flat as shown. Place LEFT front gable panel as shown and secure using 1-1/" nails as shown. 3 Place RIGHT front gable panel flush to left panel. Secure using 1-1/" nails as shown. 4 You have finished assembling your front wall gable. 1-3/4" (4,5 cm) PWA WJ DQ XTA Primed side up 1-3/4" (4,5 cm) 1-1/" (3,8 cm) Primed side up WJ WJ 33

36 BACK WALL GABLE PARTS REQUIRED: WJ x 3 x 18-3/8" (5,1 x 7,6 x 50, cm) TEMPORARY SUPPORT 1-1/" (3,8 cm) RZ x 4 x 35-3/4" (5,1 x 10, x 90,8 cm) 1 Orient parts on flat as shown. Place LEFT back gable panel on RZ as shown and secure using 1-1/" nails, 6" apart. 3 Place RIGHT back gable panel on RZ and flush to left panel. Secure using 1-1/" nails, 6" apart. 4 You have finished assembling your back wall gable. 1-3/4" (4,5 cm) 3-1/" (8,9 cm) RZ WJ Primed side up 6" (15, cm) 35-3/4" (90,8 cm) 4" (10, cm) Primed side up WJ WJ 6" (15, cm) 34

37 PARTS REQUIRED: FRONT WALL GABLE x4 1-1/" (3,8 cm) Preassembled 1 3 Caulk on top of front wall panels first as shown. Place front gable assembly centered on front wall panel and flush to rafter peak (Fig. A). Secure front gable panels into top plate using 1-1/" nails, 6" (15, cm) apart. While supporting rafter and assembly, secure gable panels to rafter using 1-1/" nails, 6" apart. Wipe excess caulk from panels. 4 You have finished attaching your front wall gable panels. Panels will be slightly offset from rafter. Fig. A 1-1/" (3,8 cm) Nails 6" (15, cm) 6" (15, cm) 35

38 PARTS REQUIRED: 96" (43,8 cm) Z-STRIP BACK WALL (Gable Z-Strip) x7 " (5,1 cm) 1 Center Z-Strip on back wall panels (Fig. A). Secure to UN using seven " finish nails, 16" apart 3 You have finished attaching your Gable Z-Strip. " (5,1 cm) Finish Nails Fig. A UN CENTER ON WALL PANELS 16" (40,6 cm) " (5,1 cm) Finish Nails OUTSIDE OF SHED 36

39 PARTS REQUIRED: BACK WALL GABLE 7 1-1/" (3,8 cm) Preassembled 1 Center back wall gable assembly on z-strip. Gable panels should be flush to wall panel as shown (Fig. A). While keeping panels flush, secure gable assembly to UN using 1-1/" nails, 6" (15, cm) apart. 3 You have finished attaching your back wall gable panels. 1-1/" (3,8 cm) Nails Fig. A 1/" (1,3 cm) Gap for Loft Deck 1-1/" (3,8 cm) Nails 6" (15, cm) 1/" (1,3 cm) Gap for Loft Deck 37

40 PARTS REQUIRED: UN x 4 x 94-1/" (5,1 x 10, x 40 cm) LOFT SUPPORTS x8 1 3 Center first loft support UN on top plate and flush against rafter as shown (Fig. A). Secure UN to rafter using four 3" screws (Fig. A). Center second loft support UN on top plate and 13" (33 cm) from rafter (Fig. A). Secure UN to top plate using four 3" screws (Fig. A). You have finished attaching your loft supports. Fig. A 13" (33 cm) UN Screws Screws UN 13" (33 cm) Screws 38

41 PARTS REQUIRED: WJ x 3 x 18-3/8" (5,1 x 7,6 x 50, cm) PL x 3 x 93" (5 x 7,6 x 36, cm) SHELF & WORKBENCH x8 x4 1 Place shelf support WJ at same height as horizontal wall brace and secure using two 3" screws into back stud and two 3" nails into first stud as shown. () 3" (7,6 cm) Screws () 3" (7,6 cm) Screws WJ SAME HEIGHT BACK WALL SAME HEIGHT WJ () 3" (7,6 cm) Nails () 3" (7,6 cm) Nails 3 Repeat Step 1 to attach second shelf support WJ. Place PL flush to shelf supports and 8-5/8" (1,9 cm) from back stud as shown. 8-5/8" (1,9 cm) 8-5/8" (1,9 cm) PL () 3" (7,6 cm) Screws () 3" (7,6 cm) Screws 39

42 PARTS REQUIRED: TP x 4 x 96" (5 x 10, x 43,8 cm) SHELF & WORKBENCH x4 4 Measure and mark for workbench support TP up from the floor 35-3/4". Secure TP using two 3" nails into studs as shown. BACK WALL MARK HERE MARK HERE () 3" (7,6 cm) Nails 35-3/4" (90,8 cm) TP MEASURE UP FROM FLOOR 35-3/4" (90,8 cm) () 3" (7,6 cm) Nails 40

43 PARTS REQUIRED: 7/16 x 11-7/8 x 88-7/8" (1,1 x 30, x 5,7 cm) 7/16 x 3-7/8 x 88-7/8" (1,1 x 60,6 x 5,7 cm) SHELF & WORKBENCH /4" (3, cm) 1-1/" (3,8 cm) 5 Place 11-7/8" shelf panel and 3-7/8" workbench panel on support and fit into groove. Secure front of panels with 1-1/4" screws, 9" apart. Secure back of panels with 1-1/" nails, 9" apart. (10) 1-1/" (3,8 cm) Nails against back wall 11-7/8" (30, cm) BACK WALL SHELF (10) 1-1/" (3,8 cm) Nails against back wall (10) 1-1/4" (3, cm) Screws 3-7/8" (60,6 cm) WORKBENCH (10) 1-1/4" (3, cm) Screws 6 You have finished installing your shelf and workbench. 41

44 PARTS REQUIRED: LOFT PANEL x6 " (5,1 cm) 7/16 x 35-7/8 x 8" (1,1 x 91,1 x 08,3 cm) 1 Place loft panel onto the three loft supports centered from side-to-side and flush with the back wall panel. Fit panel into gap. IMPORTANT! Use only SIX " nails in the panel, to allow squaring the roof. You will complete nailing the loft panels later. 3 You have temporarily finished your loft panels. Fit panel into gap. 8" (08,3 cm) CENTER 3/4" (1,9 cm) Overhang Attention: Load not to exceed 300 lbs evenly distributed across loft. 4

45 PARTS REQUIRED: WW x 4 x 69-7/8" (5,1 x 10, x 177,5 cm) BACK GABLE TRIM 0 1-1/4" (3, cm) 1 3 Position one WW flush to back gable panel edge and center with panel seam (Fig. A). Attach trim with ten 1-1/4" screws from inside approximately 7" (17,8 cm) apart. Position second WW flush to panel edge and flush to WW already attached (Fig. A). Attach trim with ten 1-1/4" screws from inside approximately 7" (17,8 cm) apart. Reinforce WW with one 3" screw through loft support at each end (Fig. B). 4 You have finished attaching your back gable trim. HINT: Clamp in position before screwing. Fig. A 7" (17,8 cm) with panel edges. WW with panel edges. 1-1/4" (3, cm) Screws Screws Fig. B 43

46 PARTS REQUIRED: x4 x4 WE x 3 x 68-7/16" (5,1 x 7,6 x 173,8 cm) DY x 3 x 7-7/8" (5,1 x 7,6 x 0 cm) FRONT WALL OVERHANG FRAMING x4 BUILD FOUR OVERHANG FRAMES. 1 Orient parts on flat as shown. Ensure WE is oriented with 4" flat edge contacting DY. Secure DY flush to WE using one screw. 3 Repeat Step 1- to make three additional assemblies. 4 You have finished assembling your overhang framing. 3-3/16" (8,1 cm) HINT: Pre drill to avoid splitting wood. 68-7/16" (173,8 cm) Screw WE DY 4" (10, cm) Flat 7-7/8" (0 cm) -1/" (6,4 cm) x4 44

47 FRONT WALL OVERHANG PARTS REQUIRED: 3/8 x x 5" (1 x 5,1 x 30, cm) Pre-assembled 0 x4 " (5,1 cm) 1 Position x 5" spacer flush to front of rafter and wall panel. Secure using two " (5,1 cm) nails (Fig. A). Position overhang framing flush to rafter (Fig. B, C). Secure using five 3" screws 3 Repeat steps 1- on opposite side. HINT: Clamp in position before screwing. Fig. C to top of rafter x 5" Screws Fig. B 45 " (5,1 cm) Nails Fig. A Screws

48 FRONT WALL OVERHANG PARTS REQUIRED: 3/8 x 7-7/8 x 57-7/8" (1 x 0 x 147 cm) 1-1/4" (3, cm) Ensure overhang boards meet at peak (Fig. A). 4 5 Position right 57-7/8" overhang board Primed Side Down flush to front wall and framing assembly (Fig A). Secure using six 1-1/4" screws. Position left 57-7/8" overhang board Primed Side Down flush to front wall, framing assembly and right overhang board (Fig. A). Secure using six 1-1/4" screws. Fig. A 1-1/4" (3, cm) Screws Primed Side Down Center and at peak. to wall. 1-1/4" (3, cm) Screws 46

49 FRONT WALL OVERHANG PARTS REQUIRED: 3/8 x 7-7/8 x 7-7/8" (1 x 0 x 0 cm) x4 1-1/4" (3, cm) 6 7 Position right 7-7/8" overhang board Primed Side Down flush to front wall and soffit block (Fig. A). Secure using two 1-1/4" (3, cm) screws. Position left 7-7/8" overhang board Primed Side Down flush to front wall and soffit block (Fig. B). Secure using two 1-1/4" (3, cm) screws. Fig. B Fig. A Soffit Block Soffit Block Primed Side Down Primed Side Down 1-1/4" (3, cm) Screws 1-1/4" (3, cm) Screws 47

50 FRONT WALL OVERHANG PARTS REQUIRED: 3/8 x 5-13/16 x 7-7/8" (1 x 14,8 x 0 cm) x4 1-1/4" (3, cm) 8 9 Position right 5-13/16" overhang board Primed Side Out flush to front wall and previously installed overhand boards (Fig. A). Secure using two 1-1/4" screws Position left 5-13/16" overhang board Primed Side Out flush to front wall and previously installed overhand boards (Fig. B). Secure using two 1-1/4" screws. Fig. B Primed Side Out Fig. A Primed Side Out 1-1/4" (3, cm) Screws 1-1/4" (3, cm) Screws 48

51 PARTS REQUIRED: Preassembled FRONT WALL OVERHANG 6 1-1/4" (3, cm) Position overhang framing flush to front of overhang boards. (Fig. A). Secure bottom of overhang framing first as shown using three 1-1/4" screws. Continue securing overhang framing while traveling toward peak as shown Repeat Step 10 on opposite side. Secure overhang framing together using one 3" screw (Fig. A). Screw 1-1/4" (3, cm) Screws LAST 1-1/4" SCREW Fig. A FIRST 1-1/4" SCREW 1-1/4" (3, cm) Screws 1-1/4" (3, cm) Screws 49

52 PARTS REQUIRED: WMR 19/3 x 4 x 69-7/8" (1,5 x 10, x 177,5 cm) FRONT WALL OVERHANG " (5,1 cm) WML 19/3 x 4 x 69-7/8" (1,5 x 10, x 177,5 cm) 13 Position WML with primed side out and flush to peak and overhang framing as shown (Fig. A). Secure using " finish nails, 1" apart as shown. 14 Repeat Step 1 on opposite side with WMR. 15 You have completed installing your front wall overhang. Hint: Pre-set nails in trim before final installation. " (5,1 cm) Finish Nails Fig. A WML WMR 50

53 SOFFIT NAILER PARTS REQUIRED: WS 1 x x 43-1/" (,5 x 5,1 x 110,5 cm) ZM 1 x x 96" (,5 x 5,1 x 43,8 cm) WD USE AS GAUGE BLOCK x 3 x 5-1/8" (5,1 x 7,6 x 13 cm) x3 " (5,1 cm) Place a square flush to bottom side of rafter and side wall (Fig. A). Mark wall at each rafter. Align WS flush to marks (Fig. A) and use WD as a gauge block as shown (Fig. B). Secure at each rafter using " nails angled to hit stud (Fig. C). Use two nails at seam. Place ZM flush to WS and marks. Secure at each mark using " nails angled to hit stud (Fig. C). Repeat Steps 1-3 on opposite side. You have finished installing your soffit nailer Use WD as gauge block Fig. A " (50,8 cm) Nails 1-1/ (3,8 cm) Fig. B to Mark " (50,8 cm) Nails WS Mark WS TOP VIEW Fig. C Stud ZM WS ZM " (5,1 cm) Nails at angle 51

54 SOFFIT BLOCK PARTS REQUIRED: WD x 3 x 5-1/8" (5,1 x 7,6 x 13 cm) x6-1/" (6,4cm) 1 Position WD flush against side wall and bottom of WS. Attach with three -1/" screws as shown (Fig. A). Repeat Step 1 for opposite side (Fig. B). 3 You have finished attaching your back wall soffit block. WD (3) -1/" (6,4 cm) Screws (3) -1/" (6,4 cm) Screws WD Fig. A Fig. B HINT: Pre drill to avoid splitting wood. 5

55 SOFFIT PARTS REQUIRED: 3/8 x 5-3/16 x 7" (1 x 13, x 18,9 cm) 3/8 x 5-3/16 x 69-3/8" (1 x 13, x 176, cm) x3 1-1/4" (3, cm) 1 Place 7" soffit board primed side down on bottom side of rafter and nailer (Fig. A) and flush to front overhang (Fig. B) and side wall. Secure using 1-1/4" screws 1" (30,5 cm) apart and angle into rafter at rafter (Fig. C). 3 Place 69-3/8" soffit board primed side down on bottom side of rafter and nailer (Fig. A) and flush to back overhang (Fig. C) and side wall. Secure using 1-1/4" screws 1" (30,5 cm) apart and angle into rafter at rafter (Fig. C). Repeat Step 1 and Step on opposite side. 4 You have finished installing your front soffit panels. Fig. D Fig. A 1-1/4" (3, cm) Screws 1-1/4" (3, cm) Screws 69-3/8" (176, cm) Fig. C Rafter Soffit Nailer 1" (30,5 cm) 7" (18,9 cm) Fig. B SIDE VIEW CENTER 1-1/4" (3, cm) Screws Primed Side Down 53

56 BACK WALL SOFFIT CAP PARTS REQUIRED: 19/3 x 6-15/16 x 5-1/" (1,5 x 17,6 x 13,4 cm) x6 " (5,1 cm) 19/3 x 6-15/16 x 5-1/" (1,5 x 17,6 x 13,4 cm) 1 Position LEFT corner soffit cap primed side up on back wall with 6-15/16" measurement down and flush to bottom of soffit board as shown. Attach cap with three " finish nails as shown (Fig. A). Repeat step 1 to install RIGHT corner soffit cap (Fig. B). 3 You have finished attaching your back wall triangle trim. Fig. A Fig. B to soffit board to soffit board 6-15/16" (17,6 cm) 6-15/16" (17,6 cm) Primed Side Up Primed Side Up 54

57 ROOF PANELS PARTS REQUIRED: 7/16 x 8-7/8 x 70" (1,1 x,5 x 177,8 cm) 7/16 x x 46-1/" (1,1 x 55,9 x 118,1 cm) 7/16 x x 96" (1,1 x 55,9 x 43,8 cm) x4 " (5,1 cm) 3/4" GAUGE BLOCK 7/16 x 47-7/8 x 48" (1,1 x 11,6 x 11,9 cm) 7/16 x 48 x 94-1/" (1,1 x 11,9 x 40 cm) Roof panels may cause serious injury until securely fastened. You must square the roof by attaching one panel first. You will use the panels long edge as a lever to bring your roof into square. Commonly known as racking. 1 Attach the 48 x 94-1/" panel with the rough side up (painted-grid lines side) with a 3/4" (1,9 cm) measurement on the rafter (Fig A) and the panel flush at the peak (Fig. B). at peak. Secure panel with two " (5,1 cm) nails in the corners. Gauge Block 48" (11,9 cm) Fig. B Fig. A 3/4" (1,9 cm) Two Nails at peak. Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until the top corner is flush to the peak (Fig. C) and panel is flush to back wall gable trim (Fig. D). Fig. C You may need to move your back wall gable to make panel flush. Secure panel with two " nails in the corners. Fig. D 55

58 ROOF PANELS PARTS REQUIRED: 8 " (5,1 cm) 3 Keep spacing between the center of the rafters at the lower edge of the panel and secure with one " nail into each rafter (Fig. E). -1/" (57, cm) Fig. E NOTE: Measurement from outside of trim. 4" (61 cm) 4" (61 cm) 4" (61 cm) 4" (61 cm) 3-7/8" (60,6 cm) Move to the top of the panel and keep spacing between the center of the rafters. Secure with one " nail into each rafter (Fig. E). 4 Nail the roof panel using " nails 6" apart on edges and 1" apart inside panel. Attach the second 47-7/8 x 48" upper roof panel flush to first panel and peak (Fig. F, G). At back end attach x 46-1/" roof panel flush to back gable trim and large roof panel (Fig. H) 6" (15, cm) " Nail 1" (30,5 cm) Fig. F at peak. Fig. G 5 Nail the roof panel using " nails 6" apart on edges and 1" apart inside panel. Attach x 96" roof panel flush to the installed panel (Fig. I) and front rafter. 7/16 x 47-7/8 x 48" (1,1 x 11,6 x 11,9 cm) 48" (11,9 cm) 6 Nail the roof panel using " nails 6" apart on edges and 1" apart inside panel. Attach 8-7/8 x 70" roof panel flush to the front overhang trim and peak (Fig. J). Nail the roof panel using " nails 6" apart. Gable Trim Fig. H at peak. 7 Repeat process to attach roof panels on the opposite side. 6" (15, cm) Fig. J 1" (30,5 cm) 8 You have finished installing your roof panels. 3/4" (1,9 cm) Fig. I 3/4" (1,9 cm) 70" (177,8 cm) to trim 56

59 PARTS REQUIRED: SP x 4 x 48" (5,1 x 10, x 11,9 cm) COLLAR TIES 1 Position and level collar tie on second and fourth rafter from back wall. HINT: For best appearance install collar tie on rafter facing away from door opening. Glue collar tie and attach with 3" nails as shown. 3 You have finished installing your collar ties. Glue Nails SP Glue LOFT 57

60 LOFT PANEL PARTS REQUIRED: 8 " (5,1 cm) 1 Continue nailing " nails in each loft panel support as shown. You have finished your loft panel. " (5,1 cm) Nails Attention: Load not to exceed 300 lbs evenly distributed across loft. 58

61 PARTS REQUIRED: 5-11/16 x 7-13/16" (14,4 x 19,8 cm) 5-11/16 x 7-13/16" (14,4 x 19,8 cm) FRONT WALL DECORATIVE TRIM 7-1/4 x 18-1/4" (18,4 x 46,4 cm) WITH WOOD GRAIN ON FACE " (5,1 cm) 1 Position right corner soffit cap Primed Side Out flush to bottom of overhang as shown. Secure using three " finish nails (Fig. A). 3 Position left corner soffit cap Primed Side Out flush to bottom of overhang as shown. Secure using three " finish nails (Fig. B). Position center gable decorative trim flush to peak of overhang as shown. Secure using six " finish nails. 4 You have finished installing your front wall decorative trim. Fig. B Fig. A Primed Side Out Primed Side Out Primed Side Out " (5,1 cm) Finish Nails " (5,1 cm) Finish Nails 59

62 FASCIA PARTS REQUIRED: 3/8 x -3/4 x 80-1/4" (1 x 7 x 03,8 cm) 3/8 x -3/4 x 69" (1 x 7 x 175,3 cm) x56 " (5,1 cm) 1 Attach fascia boards flush to rafters and flush to roof panels (Fig. A) using two " finish nails at each rafter and four " finish nails at seam. Repeat Step 1 to attach fascia on opposite side. 3 You have attached your fascia. 3/8 x -3/4 x 69" (1 x 7 x 175,3 cm) 3/8 x -3/4 x 80-1/4" (1 x 7 x 03,8 cm) SEAM 3/8 x -3/4 x 69" (1 x 7 x 175,3 cm) 3/8 x -3/4 x 80-1/4" (1 x 7 x 03,8 cm) Fig. A to roof panels " (5,1 cm) Finish Nails 60

63 DOORS PARTS REQUIRED: OO 1-1/4 x -1/ x 69" (3, x 6,3 x 175,3 cm) GAA 1 x 3 x 5" (,5 x 7,6 x 1,7 cm) x4 1-5/8" (4,1 cm) Left Door Assembled Right Door Assembled 1 3 Orient parts as shown on flat surface. and green (left) on hinge board. 3/8" offset is to top. Look for red (right) Attach temporary support OO with 3" screws in middle and at ends as shown. Tighten securely. Attach temporary support GAA with two 1-5/8" screws as shown. Tighten securely. OFFSET 3/8" (1 cm) GREEN HINT: Use 3/8" SPACERS to separate doors. SPACER 3/8" (1 cm) RED 3/8" OFFSET (1 cm) 3-1/" (59,7 cm) (4) Screws OO Tighten screws securely. Screws 1-1/4" (3 cm) NOTE: Screw hole will be used later. GAA 3/4" (1,9 cm) 3-1/" (59,7 cm) 3/4" (1,9 cm) 3/8" (1 cm) 61 Bottom edges flush.

64 DOORS PARTS REQUIRED: OO 1-1/4 x -1/ x 69" (3, x 6,3 x 175,3 cm) 3 4 Attach temporary support OO as a ledger board flush under wall panels for doors to rest on, using three 3" screws (Fig. A). OO Fig. A OO against wall panels Center doors on panel seam as shown (Fig. B). Check ledger board is still flush under panels. Screw hinge boards into wall supports and floor using ten 3" screws as shown. Make sure screws go into framing and floor (Fig. C, D). Remove temporary supports and check doors open properly. 8 You have finished installing your doors. SEAM 3/8" (1 cm) Fig. B Fig. C Angle Screw Screws into the wall support and floor frame. Fig. D 6

65 DOOR TRIM PARTS REQUIRED: x4 GI 19/3 x 3 x 3" (1,5 x 7,6 x 58,4 cm) DKA 19/3 x 3 x 44-1/8" (1,5 x 7,6 x 11,1 cm) DNA 19/3 x 3 x 64-7/16" (1,5 x 7,6 x 163,7 cm) 3/4" (1,9 cm) 1 Bagged seperately / special coating 64" Metal Threshold x56 x5 3/4" (1,9 cm) " (5,1 cm) Secure door trim from inside using 3/4" screws as shown (Fig. A). Secure top two horizontal door rails GI 9" down with four 3/4" screws from behind as shown. Secure two vertical door rails DKA with four 3/4" screws from behind to center of door as shown. 3 Secure other two GI below DKA with four 3/4" screws from behind as shown. 4 Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown in Fig. B. Use two screws at seams. Center trim DNA over doors and secure using five " finish nails into framing as shown. Center metal threshold between doors and secure using eleven 3/4" special coating screws into floor as shown (Fig, C). 7 You have finished securing your door and trim. DNA CENTER " (5,1) Nails x5 Nail into framing. Door Panel 3/4" (1,9 cm) Screws from behind. Fig. A 9" (,9 cm) CENTER Door Trim CENTER DKA GI DKA GI 9" (,9 cm) GI DKA (11) Special Coating Screws Two Screws Fig. B Fig. C 63

66 DOOR WINDOWS PARTS REQUIRED: x8 3/4" (1,9 cm) Transom Window Left Door Right Door 1 Apply high quality exterior-grade caulk behind frame near edge before installing to seal window. From back side of door, position window in opening and ensure square with door edge. Use four screws to secure each window. 3/4" (1,9 cm) Screws x8 BACK SIDE OF DOORS You must caulk completely around window frame and all exposed door panel edges and trim to validate your warranty. Use a paintable exterior rated caulk. 64

67 PARTS REQUIRED: OO 1-1/4 x -1/ x 69" (3, x 6,3 x 175,3 cm) DOOR STIFFENERS 4 " (5,1 cm) Center OO vertically on the left door in the door opening flush with the edge of door (Fig. A). 1 Secure using (7) 3" screws through outside trim into OO (Fig. B) 3 Repeat Steps 1- to install OO on right door. 4 You have finished installing your door stiffeners. OO Center OO in door opening. Fig. A IT IS IMPORTANT TO HOLD THESE DIMENSIONS 7/8" (, cm) Fig. B Hold OO tight against window glass. 5/8" (1,6 cm) OFFSET Screws " (5,1 cm) " (5,1 cm) Screws 4 11" (7,9 cm) Approximately 65

68 DOOR HARDWARE PARTS REQUIRED: x8 1" (,5 cm) 5/16" (0,8 cm) Drill Bit 1 Place bolt onto OO in open position with bolt end 3/8" down from frame. Bolt is open when loop is contacting base (Fig A). Mark and pre-drill holes for screws. 3 4 Install bolt with screws supplied and drill 5/16" hole for bolt to extend into. Place bolt onto OO in open position with bolt end 1/" up from floor. Bolt is open when loop is contacting base (Fig B). Mark and pre-drill holes for screws. Install bolt with screws supplied and drill 5/16" hole for bolt to extend into. Fig. A 5 You have finished installing your barrel bolts. LOCATE AND PRE-DRILL HOLES TO AVOID SPLITTING WOOD OVER DOOR FRAME 5/16" drill for bolt: 1" deep. OO 1-1/4 x -1/ x 69" 3/8" with bolt in open position. x4 OPEN POSITION, Spring is loose. PRE-DRILL (4) HOLES LEFT DOOR Loop contacts base. 1-1/4 x -1/ x 69" OO Loop contacts base. x4 OPEN POSITION, Spring is loose. FLOOR 1/" 5/16" drill for bolt: 1" deep. PRE-DRILL (4) HOLES 66 Fig. B

69 PARTS REQUIRED: DOOR HARDWARE / DECORATIVE HINGES 3/4" (1,9 cm) 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill hole with 1/4" drill. Re-drill hole with 1/" drill. x4 1/" (1,3 cm) Drill Bit 1/4" (0,6 cm) Drill Bit 1-1/" (3,8 cm) Keep drilled hole square to trim to avoid breaking edge of Door Stiffener. to hinge RIGHT DOOR. 1-1/" (3,8 cm) TOP VIEW 35-3/4" 90 cm 1-1/" 3,8 cm Fig. A 1/4" Pre-drill and 1/" Drill-through. 3 4 Insert handle in hole and secure using 1-1/" (3,8 cm) screws. Attach inside handle and secure with set screw as shown. Install decorative hinges on horizontal trim and flush against hinge as shown. 5 You have finished installing your T-handle and decorative hinges. SET SCREW 1-1/" (3,8 cm) 67

70 GABLE WINDOW PARTS REQUIRED: x4 1-1/4" (3, cm) Gable Window 1 Apply high quality exterior-grade caulk behind frame near edge before installing to seal window. From outside of shed, position window in opening and level. Use four screws at corners of windows. Do not overtighten screws. You must use a caulk sealant behind window flange in order to validate your warranty. 4 Screws HINT: Caulk behind frame near edge before installing. 68

71 TRIM PARTS REQUIRED: EFA 19/3 x -1/ x 11-1/" (1,5 x 6,4 x 9, cm) EU 19/3 x -1/ x 17" (1,5 x 6,4 x 43, cm) GABLE WINDOW 0 " (5,1 cm) x8 1/" (1,3 3 4 Center window trim on window. NOTE: There will be a slight reveal inside window. Secure window trim using " finish nails as shown (Fig. A) 1/" (1,3 cm) Screws Avoid Nailing Into Metal Window Flange Use WQ as temporary spacer DQ 4" (10, cm) EU 1/" (1,3 cm) Screws EFA EFA CENTER TRIM ON WINDOW EU 4" (10, cm) DQ Fig. A (8) " (5,1 cm) Finish Nails 69

72 GABLE WINDOW PARTS REQUIRED: x4 3/4" (1,9 cm) 5 From inside, snip protruding finish nails. Install 3/4" screws into backside of vertical window trim EFA from inside as shown. Do not screw into window flange. 6 You have finished installing your window. INSIDE OF SHED 3/4" (1,9 cm) Screws 70

73 PARTS REQUIRED: x8 3/8 x 1-3/4 x 67-3/4" (1 x 4,4 x 17,1 cm) TRIM x56 " (5,1 cm) 1 Attach one trim flush under soffit panel and along adjacent wall (Fig. A, B) using two " (5,1 cm) finish nails as shown. Position second trim flush to top and edge of previously installed trim (Fig. A, B). Secure using two " (5,1 cm) finish nails as shown. Finish attaching trim flush to corners (Fig. B ) using six " (5,1 cm) finish nails as shown. 3 Repeat Steps 1- to attach trim to all four corners. 4 You have attached your corner trim. Fig. A under soffit panel. Seam is flush. Caulk seam before painting trim. 67-3/4" (17,1 cm) Fig. A /4" (17,1 cm)