Matrix BGA Socket Assembly Instructions
|
|
- Hector Horton
- 6 years ago
- Views:
Transcription
1 s 0,80mm, 1,00mm, 1,7mm Pitch MPI Rev.
2 mm Hex Wrench (Not Supplied.). Spring Plate Assembly. ( Item). Top Support Plate. ( Item) 4. BGA Package (Not Supplied.) 5. Matrix MPI BGA Socket Assembly. (Purchased Separately) 6. Printed Circuit Board (Not Supplied.) 7. Bolster Plate Assembly with Insulator. ( Item) MPI Rev.
3 1.) Place Bolster Plate Assembly with Insulator on a clean dry flat surface..) Next place the Printed Circuit Board on the Bolster Plate Assembly, with the socket pads facing up, carefully aligning the four (4) holes in the board with the four posts located on the Plate. MPI Rev.
4 Press Here Press Here.) Carefully holding the socket by the edges only. (Care must be taken not to touch the MPI ). Place the socket on the PCB, aligning the posts on the socket to the holes in the PCB. Pushing down gently on the corners of the Location frame to seat the socket. 4.) Holding the BGA package by its edges. Place the package in the socket. The corner frames help align the package to the holes in the socket. (Do not Push down on the socket as this will Compress the MPI contacts). 4 MPI Rev.
5 5.) Align the four (4) holes in the plate to the four (4) posts and place the Top Support plate on top of the BGA Package. Place Slide 6.) Place the Spring Plate Assembly on the post, by first insert the post thru the larger hole and then sliding the plate to capture the spring under the heads of the post. 5 MPI Rev.
6 7.) Using your thumb and forefinger, slowly turn the hex screw in a clockwise direction, until all the variances has been removed from the assembly. The spring plate should not have a deflection, but should be in contact with the head of the corner posts. corner post head variance Before After 6 MPI Rev.
7 8.) Now remove the Hex wrench and Place it as shown in the above graphic. ¼ Turn Start (1 Full Turn) ½ Turn ¾ Turn 9.) Turn the Hex Wrench the correct number of turns as prescribed in the table on the following Pages.(No. of Vary according to Socket Size, pitch, and hardware kit.) 7 MPI Rev.
8 Table 0,80 mm Sockets 196 * 0,80mm BGA Socket Part / -1/ -1/ -1/ -1/ * Be sure to verify the number of contacts and the Part. Using the Wrong could damage the MPI. 8 MPI Rev.
9 Table 1,00 mm Sockets * 1mm Small BGA Socket 56 Part / * 1mm Medium BGA Socket 15 Part / / 1-1/ -1/ -1/ * 1mm Medium BGA Socket Part / -1/ -1/ -1/ 151 * 1mm Large BGA Socket Part / / / -1/ / * Be sure to verify the number of contacts and the Part. Using the Wrong could damage the MPI. 9 MPI Rev.
10 Table 1,7mm Sockets * 1,7mm Small BGA Socket 56 Part / * 1,7mm Medium BGA Socket 79 Part / / / / / / * 1,7mm Large BGA Socket Part / -1/ * 1,7mm Medium BGA Socket Part / / / / / / / * Be sure to verify the number of contacts and the Part. Using the Wrong could damage the MPI. 10 MPI Rev.
11 , Revision History 1. Preliminary Release 0/6/0. Preliminary Change 10/01/04 MPI Rev.
Phone #: (360) Online Tech Support: Web:
Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz Your new Model D2058A Super-Heavy Duty Mobile Base () is designed to give you a stable and mobile platform upon
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationParts Included: T-Feet Assembly
Parts Included: T-Feet Assembly Foot Kit: J-Rail Kit: Column Kit: 2 Feet 2 T-Top Supports 2 J-Rails Hex Rod to be Included on a Crank Assembly only. 2 Electric or Crank Columns 3 rd Leg option for 3 leg
More information3. Remove the flue collar by backing out the two Phillips round head machine screws.
SERVICE MANUAL SERVICE PROCEDURES Defiant Non-Catalytic Model 1610 Woodstove **Wear gloves, a dust mask and protective eyewear when servicing a stove. ** Replacing the Fountain Assembly 1. Remove the doors,
More informationRC4WD R2 Disconnect Transmission parts replacement guide
RC4WD R2 Disconnect Transmission parts replacement guide Version 1.1 Thank you for your purchase. Welcome to the RC4WD family. This transmission is a combination of many specially engineered and manufactured
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationSIGNATURE FRONT BUMPER INSTALL
SIGNATURE FRONT BUMPER INSTALL JL **PLEASE READ THROUGH THE INSTRUCTIONS BEFORE BEGINNING ANY PART OF THE INSTALLATION PROCESS** 1. You can now remove the trim strip (2 vertical clips, 4 horizontal, 2
More informationMODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS
MODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Your new Model T28000 Heavy-Duty
More informationMS2 Straight Key Kit Assembly Manual
American Morse Equipment MS2 Straight Key Kit Assembly Manual Thank you for purchasing our MS2 Miniature Straight Key Kit! Please take a few minutes to look over these instructions before starting assembly.
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationRiverside. Windhaven Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationInstallation Guide Installation Kit for Mounting Philips MP20/30/40/50/60/70 on GE Healthcare Aisys Carestation
Installation Guide Installation Kit for Mounting Philips MP20/30/40/50/60/70 on GE Healthcare Aisys Carestation The purpose of this guide is to: 1. Describe mounting of Top Plate/Camlock Rail Assembly
More informationRiverside. Harbor Hill Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationSTEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationRiverside. Harbor Hill King Storage Bed Assembly Instructions
King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard
More informationBELGIAN EXT. REC DINING TABLE
BELGIAN EXT. REC DINING TABLE Date: Williams 20 Jul. 2015 Sonoma Product Information Dept. www.williams sonoma.com Page 1 of 5 Page 1 of 5 Important Safety Instructions: Please read all instructions carefully
More informationRIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly )
RIPPER PEDAL Bearing / Axle Replacement ( Disassembly ) 1 1. Use good quality tools to avoid stripping screw sockets. 2. When servicing your pedals, work on one side at a time to prevent parts from mixing
More informationPULL-THRU USER S MANUAL
PULL-THRU USER S MANUAL G14x Part # 310 120 177 G20 Part # 310 120 188 G20x Part # 310 120 186 G40x Part # 310 120 163 TABLE OF CONTENTS SECTION 1 PCB DESIGN AND MOUNTING SECTION 2 MOUNTING ADAPTER TO
More informationZ-Truck Up-and-Down Motion. Y-Truck Side-to-Side Motion. Head. Squaring Plate. Sliding Plate FIGURE 1: THE CARVEWRIGHT MACHINE
Setup and use of CarveWright CO2 Powered Dragster Jig The CO 2 powered Dragster Jig will arrive from the factory fully assembled, calibrated, and squared. In order to get the best results, your CarveWright
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationSilver Ball Matrix BGA Socket
A1 corner 4.600 Silver Ball Matrix BGA Socket Features Wide temperature range (-55C to +0C). Current capability is 4A per pin. Over 40GHz bandwidth @-1dB for edge pins. Low and stable contact resistance
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationInstallation Manual for the Rockmeister Roof Ladder
Installation Manual for the Rockmeister Roof Ladder Exclusively for Mercedes-Benz Geländewagen W460, W461 & W463 with single rear door NOTE: W460 & W461 models have a different Frame Bracket than the W463.
More informationPROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT
AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationNOTE: Landscape Forms is not responsible for site preparation, footings, or electrical wiring.
11/2009 Stop Embedded Mount Bollard HANDLE WITH CARE! Pangard II Polyester Powder coat is a strong, long-lasting finish. Protect this finish from damage during installation. Place unwrapped powder coated
More information1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions 1. 2.
1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions Right Stack top panels on bottom panels Unfold display wall Set in desired configuration Wrong Pull from here Remove each folded
More informationTools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket - Electrical tape
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationB9Creator Build Table Calibration Process
B9Creator Build Table Calibration Process Summary This document explains the process to calibrate the B9Creator Build Table. Things to Know The purpose of the Build Table calibration is to ensure the red
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT NISSAN NAVARA D40 2004-2015 2 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video
More informationInstallation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine
Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of Counterweight (page 2). 2. Describe
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationInstallation Guide Mounting Kit Philips MP70/EGM/FMS on Dräger Fabius Tiro
Installation Guide Mounting Kit Philips MP70/EGM/FMS on Dräger Fabius Tiro The purpose of this guide is to describe mounting of parts on the anesthesia machine. WARNING: USE OF MOUNTING HARDWARE AND MONITORING
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationSide Winder R o u t e r L i f t.
Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstallation Guide Philips IntelliVue MP20/30/40/50/60/70 MX400/450/500/550/600/700/800 M-Series Arm Mounting Kit for Dräger Primus Anesthesia Machine
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Philips IntelliVue MP20/30/40/50/60/70 MX400/450/500/550/600/700/800 M-Series Arm Mounting
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT ISUZU MU-X 2013+ LS-M & LS-U MODELS ONLY 3 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More informationHONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationTherma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)
Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips
More informationFully Demountable Torch Installation Instructions (Axial Version)
Fully Demountable Torch Installation Instructions (Axial Version) Introduction Applications This instruction sheet covers the installation of the fully demountable torch for axial ICP-OES instruments (Vista-PRO,
More information4 DOOR JK ROCK SLIDERS INSTALLATION
SIGNATURE SERIES 4 DOOR JK ROCK SLIDERS INSTALLATION 1. To remove either the Jeep JK Wrangler Unlimited Rubicon rocker guards or Sahara running boards, use a 10mm wrench to remove the 3 pairs of nuts securing
More informationINSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON BALDOR LATHE
DENTAL, INC. TECHNICAL BULLETIN Q832-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE THIS PRODUCT IS
More informationRibcage Installation. Part 2 - Assembly. Back-Bone V1.06
Ribcage Installation Part 2 - Assembly Back-Bone V1.06 Contents Section 1 Before You Get Started... 2 Included With Your Kit:... 2 Figure: A... 3 CAUTION!... 4 Note:... 4 Tools Required... 5 Section 2:
More informationLEG CURL IP-S1315 INSTALLATION INSTRUCTIONS
LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3358-2 PCN 060712-5 Side-of-Pole Mount for 4 Modules (SPM4) For
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationBig Block Installation Manual For Systems without A/C
Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru
More informationInstallation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays
Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read
More informationStarving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24
SS2 guide Written By: 6L6 2019 guides.diyaudio.com/ Page 1 of 24 INTRODUCTION This is a build guide for the hybrid headphone/pre-amplifier. You can buy a kit at the SSII product listing on the diyaudio
More informationPage 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with
More information6000 Horizontal Router Table Owners Manual Please Read Carefully!
6 Horizontal Router Table Owners Manual Please Read Carefully! Parts List Please identify and verify that you have all of the hardware & parts shown prior to assembly. The parts described in this box are
More informationOPERATING INSTRUCTIONS for. Gold-Print TM. Model SPR-10 Screen and Stencil Printer
OPERATING INSTRUCTIONS for Gold-Print TM Model SPR-10 Screen and Stencil Printer TABLE OF CONTENTS INSTALLATION...3 Z ADJUSTMENTS...3 X, Y & Ø ADJUSTMENTS...4 CIRCUIT BOARD POSITIONING...5 ILLUSTRATIONS...6
More informationw w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models
-J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationOPERATING INSTRUCTIONS FOR MODEL SPR-25 Manual Stencil Printer
OPERATING INSTRUCTIONS FOR MODEL SPR-25 Manual Stencil Printer TABLE OF CONTENTS I. INSTALLATION...3 II. SET-UP...4 III. Z AXIS ADJUSTMENT (Screen Height)...6 IV. X, Y AND Ø ADJUSTMENTS...6 V. SQUEEGEE
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationVector Frame Counter 06
Vector Frame Counter 06 VFC-06 Vector Frame counters compliment the Vector Frame series of exhibit kits, but are also ideal for any stand-alone event or display. Vector Frame counters couple simple extrusion-based
More informationDUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS
DUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS Copyright 2010. Star Trac by Core Industries, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 1285 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0248 ORDER OF ASSEMBLY
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationC PART LIST HARDWARE LIST. Kitchen Cart IMPORTANT NOTE
88 9200 006C Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken
More informationINSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1
INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount
More informationINSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS
INSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS The Universal Interface Bracket provides a solution for simplifying inventory of RPA and RPM series mounts and SLB/SLM projector brackets.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationMedium Flat Panel Dual Swing Arm Wall Mount JWD-V
INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationMobile Automotive Cart Assembly
General Information: The following provides step-by-step instructions for assembling the Mobile Automotive Cart. The finished assembly will consist of the following: (1) Cart bottom shelf, (1) or (2) shelves,
More informationDynamic Nanospray Probe (NSI-1) Installation Guide
Dynamic Nanospray Probe (NSI-1) Installation Guide This guide describes how to install the NSI-1 dynamic nanospray probe (see Figure 1) onto a TSQ Series or LTQ Series mass spectrometer and provides general
More informationZ 406 Bench work Manual
08686 Z 406 Bench work Manual Rev A Custodian: Brian Simeone Table of Contents Section Gantry Removal & Replacements Page 1.. Remove & Replace Printer Module.......3 2.. Remove & Replace Head Card Assembly.....
More informationInstallation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP80/90 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe mounting of MP90 equipment on the anesthesia machine. WARNING: USE OF MOUNTING
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type D
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type D ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 060712-7 Side-of-Pole Mount for 4 Modules (SPM4) For Module Type
More informationCABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS
Assembled cabanas are large & heavy. Assemble at place of use. CABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS Step 1 CAUTION: To avoid damage to the finish of your Cabana frame, prepare a smooth, non-scratch
More informationInstallation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine
Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe installation of MP40/50/60/70 mounting equipment on the anesthesia machine.
More informationKAWASAKI KLRE PD NERF HTP4-8-5 & HIGHWAY PEGS HTP4-1-4B
Thank you for purchasing Happy Trails products. Our products are proudly hand made in Boise Idaho, USA. If you have any questions or concerns about the installation of this product, please contact us directly
More informationInstructions for Converting the LV/MB Joystick from A to A1
Instructions for Converting the LV/MB Joystick from A to A1 TOOL LIST 1 3/8 WRENCH 1 /16 WRENCH 1 9/16 WRENCH 1 5/32 ALLEN WRENCH 1 3/16 ALLEN WRENCH 1 ¼ DRIVE PUNCH, OPTIONAL Use along with drawings:
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationMounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves
Mounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves NOTE: These instructions apply only to 60 series ball valves with bodies containing external mounting nibs. External
More information08+ KAWASAKI KLR PD NERF
08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of
More informationAeon AcousticPro UHD Series
Aeon AcousticPro UHD Series EDGE FREE Fixed Frame Sound Transparent Projection Screen User s Guide Product Description: The Aeon AcousticPro UHD Series is a fixed frame projection screen that uses Elite
More informationArc Trainer Main Frame Assembly
Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
SleepSafe Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included
More information