Installation Instructions. Designer Roman Shades
|
|
- Olivia Jordan
- 6 years ago
- Views:
Transcription
1 Installation Instructions Designer Roman Shades
2 Lutron Designer Roman Shades Installation Instructions Tools Required: Awl Tape measure Level Power drill Standard screwdriver Phillips screwdriver Notes: 1) Complete wiring and programming information can be found in the Sivoia QED Wire and Programming Guide, P/N or at 2) The Electronic Drive Unit (EDU) will need to be powered to complete installation. Box Contents: Note: When drilling into metal or wood, the included screws are sufficient but we recommend predrilling the holes. Warning: If not avoided, could result in death or serious injury. If your application requires mounting the shade to some other substrate, select a fastener (not included) that is designed to support the weight of the shade being installed. Follow the manufacturer s instructions carefully. (4) Mounting Screws (See Note Above) (1) Cord Cleat and (2) Color Match Mounting Screws (Cord and Cleat only) (1) Angle Brackets - Soft Fabrics (2) Angle Brackets and (4) Screws (2) Yankee brackets - Naturally Woven Woods (Outside Mount (only)) (1) Chain Holder and mounting screw (Chain and Clutch only) (1) Additional (wide shades) - NWW Shades Yankee brackets with short bolt Lutron Designer Roman Shades 2
3 ROLLER-64 SHIPPING BLOCK REMOVAL! IMPORTANT THE ROLLER-64 ELECTRONIC DRIVE UNIT UTILIZES WOODEN SHIPPING BLOCKS AT EITHER END OF THE SHADE. IF THE SHADING SYSTEM THAT YOU ARE INSTALLING USES THE ROLER-64 ELECTRONIC DRIVE UNIT, THE SHIPPING BLOCKS MUST BE REMOVED BEFORE INSTALLATION. FAILURE TO DO SO MAY HAVE AN UNDESIRABLE EFFECT ON THE PERFORMANCE OF THE SHADE. Remove Shipping Block Remove Shipping Block Remove Screws Securing Shipping Block to Shade Header Lutron Designer Roman Shades 3
4 1 Inside Mount (NWW or Designer Fabrics) Note: Manual lifting system shown. Electric Drive Units (EDU) shading systems install the same way. 1.1 Mark the Shade Position: M Use awl to mark shade s pre-drilled mounting holes. 1.2 Drill and Attach the Shade: D Drill mounting holes and attach shade using screws provided. Lutron Designer Roman Shades 4
5 2A Outside Mount - Naturally Woven Woods (NWW) 2.1A Determine Shade Locations Center the shade over the opening at the desired height. Mark the location of the shade headrail on the wall. Center the shade Horizontal edge Vertical edge Lutron Designer Roman Shades 5
6 2A Outside Mount - Naturally Woven Woods (NWW) (continued) 2.2A Determine the measurements to the center of each slot and transfer those measurements to the wall. Measure from the end of the headrail to the center of each slot, and mark inside slot. Yankee Bracket Stud Center of Headrail Headrail Measurement Center Lutron Designer Roman Shades 6
7 2A Outside Mount - Naturally Woven Woods (NWW) (continued) 2.3A Transfer the measurements to the center of each slot to the wall. Horizontal Center of Slot Vertical 2.4A Align the center of the bracket to the mark that you placed on the wall. Using the Yankee Bracket as a template, mark the hole locations on the wall. Make sure that the brackets are level and plumb. Align center of Bracket with Mark on Wall Side view Top of headrail Note: When determining hole locations, the top of the headrail will line up with the underside of the Yankee Bracket. Lutron Designer Roman Shades 7 Valance not shown for clarity
8 2A Outside Mount - Naturally Woven Woods (NWW) (continued) 2.5A Drill and Attach the Brackets to the Wall 2.6A Attach the Shade to the Brackets with hardware supplied (shown with third bracket (always in middle) Manual Shade Shown 2.7A Attach the Hardware Covers Velco strip (Align the VELCRO strips and press firmly.) Lutron Designer Roman Shades 8
9 2B Determine the location of your angle brackets and mark the holes on the wall. Make sure that your brackets are level and plumb. Drill and attach the brackets to the wall. Attach the shade to the brackets. Lutron Designer Roman Shades 9
10 Outside Mount - Designer Soft Fabrics - Cords Forward Make Bracket Slits in Fabric If your shade is a cords forward and is an outside mount application, slits will need to be made in the back of the fabric in order for the brackets to be inserted through the back of the shade and be attached to the headrail. Follow the steps below: Place a 1 ½ piece of masking tape on the face of the shade at each desired bracket location Mark a 1 wide cut line on the tape! IMPORTANT: When marking the slit locations, make sure they are placed exactly at the bottom edge of the headrail. If the cut is too high or low with reference to the bottom edge of the fabric, the shade fabric can bunch up or the shade cloth may tear. Mark Slit Cut Slit Using a Sharp Blade Lutron Designer Roman Shades 10
11 Attach the Cleat Finishing the Installation - Cord and Cleat or Cord Lock Lifting Systems Warning: If not avoided, could result in death or serious injury. Drill 1/16 pilot holes and attach the cord cleat to the wall using the two color-matched screws provided. The location of the cleat must be at a height that will be safe for children. To unlock the shade, pull cord down and towards center of shade. Hold cord and move shade to the desired position. To lock the shade, in place pull cord past the outside edge of shade and release. Lutron Designer Roman Shades 11
12 4 Chain and Clutch Lifting Systems 4.1 Attach the Chain Holder The shade is shipped with the chain holder attached to the chain. Hold the chain holder upright and position it so that the chain is straight. Chain should rotate around the device easily. Mark the location of the installation hole on the wall, and drill a 1 16" pilot hole. Using the screw provided, attach the chain holder as shown. Screw 4 Operating Your Chain and Clutch Shade 4.2 To Raise Shade Pull chain closest to you down until shade is at desired position. To Lower Shade Pull chain closest to the window down until shade is at desired position. Outside Inside To Lower Shade Lutron Designer Roman Shades 12 To Raise Shade Pull chain in a downward direction
13 5 Wire Placement for EDU (Electrical Drive Units) shades 5.1 Determine wire location based on your application. (Roller-64 shown). Side View Front View Bottom View Note: When deciding how to run your wire. Please take into consideration that the unit may have a wooden headrail, an optional valance, hardware covers, or returns. Lutron Designer Roman Shades 13
14 5 Wire 7-Pin Terminal Block 5.2 Strip 2 of jacket off cable. 2 in. Wire 7-Pin terminal block (provided) to cable using the included screwdriver. EGND (Yellow/Green) 24 V~ (Red) 24 V~ (Red/White) MUX (Purple) MUX (Gray) 12 V (Blue) Common (Yellow) To EDU Connector LutronDesigner Roman Shades 14
15 5 Connect Terminal Blocks 5.3 Plug 7-pin terminal block on cable into EDU terminal block attached to shade bracket. Dress wires to ensure fabric does not rub while the shade is moving. Bottom View Lutron Designer Roman Shades 15
16 5 IR Receiver Connection (if applicable) 5.4 Plug in the IR receiver. 5.5 Position the IR receiver. Note: The IR receiver should be mounted such that it is in line-of-sight with the remote control and that it does not interfere with the shade. Note: Dress wires to ensure the fabric does not rub while the shade is moving. Bottom View Note: If necessary use 10-foot (3 m) extension (SV-IR-EXT-10 sold separately). Maximum length - 50ft (15.25 m). Lutron Designer Roman Shades 16
17 5 Setting Limits from the EDU Note: The following pages for setting limits and system programming showcases the Roller-64 EDU system. The programming steps of the Roller-100 EDU system are the same. The Wiring and Programming Guide (P/N ) and/or the Technical Reference Guide (P/N ) contains further information on these steps. Setting the Open Limit from the EDU Note: Setting the Open Limit lower than the Close Limit will cause the shade to move down when raise is pressed and up when lower is pressed. Use the programming stylus to run the shade up and down using the adjustment buttons Press the Open Limit Button ( ), the green LED on the shade EDU will turn on steady, indicating that the EDU is in Set Open Limit Mode. Press the Open Limit Button Steady LED Adjust the position of the EDU to the desired Open Limit using the adjustment buttons ( ). Use the Adjustment buttons to move the EDU position Press and hold the Open Limit Button ( ) for 5 seconds. The green LED on the shade EDU will flash for 2 seconds, then go dark, indicating that the current position has been stored as the Open Limit. Press and hold the Open Limit Button Flashing LED Lutron Designer Roman Shades 17
18 5 Setting Limits from the EDU (continued) Setting the Close Limit from the EDU Press the Close Limit Button ( ). The green LED on the shade EDU will turn on steady, indicating that the EDU is in Set Close Limit Mode. Press the Close Limit Button Steady LED Adjust the position of the EDU to the desired Close Limit using the adjustment buttons ( ). Use the Adjustment buttons to move the EDU position Press and hold the Close Limit Button ( ) for 5 seconds. The green LED on the shade EDU will flash for 2 seconds, then go dark, indicating that the current position has been stored as the Close Limit. Press and hold the Close Limit Button for 5 seconds Flashing LED Lutron Designer Roman Shades 18
19 6 Finish System Programming The Sivoia QED shade is now installed, wired, and the OPEN/CLOSE limits for each shade have been set. The next step is to finish programming the system. Use the instructions in the Wiring and Programming Guide (p/n ) or the Technical Reference Guide (p/n ) and perform these four easy steps: Note: Before addressing, all keypads will operate all shades. This can be used to verify proper wiring and communication. 1. Address the system. This gives each EDU, keypad and contact closure interface in the system a unique address number or name, allowing proper communication between components. 2. Verify wiring of each EDU, keypad and interface using the LED feedback from each system component during addressing. 3. Assign shades (EDUs) to keypads, IR hand controls and/or contact closure interfaces. Tell the system which shades (EDUs) respond to which keypads, IR hand controls and contact closure interfaces. 4. Set and save PRESET shade positions if you desire them to be different from the factory defaults. Lutron Designer Roman Shades 19
20 7 Troubleshooting QED Symptom Shade will not move... Shade does not fully open or fully close... Fabric not level... Fabric not centered over window... Shade does not move smoothly... IR controls will not operate shade... Solution...If Roller-64 shipping blocks not removed....edu is not powered - check EDU Power....Shade is caught on something - free shade....shade is not assigned to keypad, IR, or CCI....Limits have been set incorrectly - refer to set open limit and set close limit sections....shade fabric is caught on something - free shade....check that brackets are mounted level....check that tracking correctly on the shade tube....check that the shade is centered....check for binding of shade fabric on window edge or trim...ir transmitter does not have line-of-sight to IR receiver....out of range - move to within 40 feet (12m) of IR receiver....edus not assigned to IR receiver....ir receiver not plugged into any EDU within range....ir remote control batteries are not providing power, replace them. MANUAL Symptom The shade will not raise or lower... When the draw cords are pulled, only one side of the shade moves up or down... Solution...Check that draw cords....are not caught on the mounting brackets or screws....make sure the shade is not caught on an obstruction, such as a part of the windowsill, crank, or latch. or...check to determine if any of the draw cords have become untied or knotted accidentally. Lutron Designer Roman Shades 20
21 Caring for Your Shade Your Designer Roman Shade will provide you with years of beauty and pleasure with minimal care and cleaning. Vacuum using a brush or dust head attachment. Dust lightly using a soft, clean cloth. Dry Clean your shade if it needs a more thorough cleaning. Never immerse the shade in water or liquids of any type. Lutron Designer Roman Shades 21
22 Limited Warranty Lutron Shading Solutions offers an 8-year limited warranty for our shading systems. Please contact customer service or visit our website for a complete warranty statement. Lutron Shading Solutions reserves the right to make improvements or changes to these products without prior notice. Although every attempt is made to ensure that this information is accurate and up to date, please check with Lutron Shading Solutions to confirm product availability, the latest specifications, and suitability for your application. This Product may be covered under one or more of the following U.S. patenets: 6,497,267; 6,983,783; 7,281,565; and corresponding foreign patents. U.S. and foreign patents pending. Lutron, the Sunburst logo, Sivoia and Sivoia QED are registered trademarks of Lutron Electronics Co., Inc. Technical Assistance Lutron Shading Solutions11520 Sun Shade Lane, Ashland, Virginia service and support: call: fax: shadinginfo@lutron.com 2008 LUTRON Electronics Co., Inc. Printed in the U.S.A. P/N REV A.
Trackstar Manual Folding Shade Installation Instructions
Trackstar Manual Folding Shade Installation Instructions Tracklock or Cord and Pulley Lifting System Thank you for purchasing your new Trackstar folding shade. It has been custom-made from the highest
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationROMAN AND. Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION INSIDE MOUNT. A few simple tools are required:
ROMAN AND WOVEN WOOD SHADES Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview...3 Mount the Standard
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationVertical Honeycomb Shades
Step by Step Installation Instructions Vertical Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from Smith+Noble. Your new shades have been
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationWOVEN WOOD SHADES Corded, Continuous Cord Loop or Upended
WOVEN WOOD SHADES Corded, Continuous Cord Loop or Upended GETTING STARTED HARDWARE INFORMATION A few simple tools are required: The hardware you received with your product are REQUIRED for proper installation.
More informationOwner s Guide. Pirouette Window Shadings. Standard EasyRise Rectangular And Two-On-One Headrail Shadings
Owner s Guide Pirouette Window Shadings Standard EasyRise Rectangular And Two-On-One Headrail Shadings Contents Introduction...3 Product View...4 Getting Started...5 Mount The Installation Brackets...6
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview...3 Mount the Standard
More informationInstallation Instructions
Transitional Shades Installation Instructions Traditional, 2-On-1 Headrail & Sundown Shades Couplitaire Modernaire Visionaire *Click on any page to return to the Table of Contents* Allure Transitional,
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationOwner s Guide. Roller Shades. Clutch Operated Standard Shades
Owner s Guide Roller Shades Clutch Operated Standard Shades CONTENTS Product View...4 Introduction...5 Getting Started...5 Tools And Fasteners Needed...5 Install The Mounting Brackets...6 Install The
More informationMETAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE
METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationBasic Spring Motor Roller Shades
Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension in order to function as intended. Handling in
More informationInstallation Operation Care
Installation Operation Care Alustra Woven Textures Traditional Roman Shades Cordlock Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Mounting Types and Window
More informationInstallation Instructions
Installation Instructions Transitional Shades Standard Transitional Shades (Small and Large Cassette) Board Mounted Transitional Shades Accu-Rise Transitional Shades Sure-Lift Transitional Shades Sundown
More informationFLEXCELL HONEYCOMB BLINDS
FLEXCELL HONEYCOMB BLINDS GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper installation. s should be installed at
More informationInstallation, Operation and Care Instructions. Retractable Cord Operating System
Installation, Operation and Care Instructions Retractable Cord Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Cordless Control with Mounting Bar or Cordless Control with Cassette Everything You Need A Smooth Set-Up We want you to love your new window
More informationStep by Step Installation Instructions. Fabric Shades. Standard, Slim Headrail and Top Down/Bottom Up
Step by Step Installation Instructions Fabric Shades Standard, Slim Headrail and Top Down/Bottom Up Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having
More informationInstallation, Operation and Care Instructions. Continuous Cord Loop Operating System
Installation, Operation and Care Instructions Continuous Cord Loop Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3
More informationCorded Honeycomb Shades
Corded Honeycomb Shades Remove shade from package. Save packaging until shade is installed and working to your satisfaction. Level Tape Measure Pencil Power drill Screwdriver s for different mounting surface:
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationFascia Shade Pocket. Parts Included With This Package: Required Tools: Installation & Operating Instructions
Motorized Shade Systems Installation & Operating Instructions Fascia Shade Pocket Ceiling SV-FASCIA-1 Fascia Shade Pocket Description The Sivoia SV-FASCIA-1 Fascia Shade Pocket (to be used in conjunction
More informationInstallation Operation Care
Installation Operation Care Designer Banded Shades Cassette with Custom Clutch and UltraGlide CONTENTS Getting Started Product View Custom Clutch... 1 Product View UltraGlide... 2 Tools and Fasteners Needed...
More informationWallboard or plastic Pre-drill holes and use hollow wall anchors or toggle bolts to install your shade in wallboard or plastic.
Woven Wood Shades Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing Woven Wood Shades from Blindster. This window
More informationLuxe Linen Honeycomb Shades
Step by Step Installation Instructions Luxe Linen Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Table of Contents Getting Started...3 THANK YOU for purchasing from
More informationDeluxe Exterior Solar Shades
Deluxe Exterior Solar Shades Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Thank you for purchasing Deluxe Exterior Solar Shades from Blindster.
More informationPremium Light Filtering Sheer Shade
Premium Light Filtering Sheer Shade Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing a Premium Light Filtering
More informationVideo Wall Installation Instructions 2W X 3H, 3W X 3H
Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...
More informationInstallation Operation Care
Installation Operation Care Designer Roller and Designer Screen Shades Standard and Cassette Cordless Lifting System CONTENTS Getting Started: Product Views... 1 Tools and Fasteners Needed... 3 Installation
More informationWHISPER Cellular EasyRise Shades. Installation Operation Care
WHISPER Cellular EasyRise Shades Installation Operation Care 05/2013 CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mounting Types
More informationHorizontal Shadings. Installation & Operating Instructions
Horizontal Shadings Installation & Operating Instructions TABLE OF CONTENTS Getting Started: Mounting Types...3 Installation Components...3 Tools and Fasteners Needed...4 Product View...5 Installation:
More informationNew Roman Shades WARNING. Installation Operation Care. Retractable Cord Lifting System
CHILD SAFETY Warning WARNING For more safety information call 1-888-501-8364 in the U.S. or 1-866-662-0666 in Canada. Young children can wrap cords around their necks and STRANGLE. Always keep cords out
More informationSTEP BY STEP INSTALLATION INSTRUCTIONS. Studio Hardware. Wall Mount Single Rod Set Motivia Motorized
STEP BY STEP INSTALLATION INSTRUCTIONS Studio Hardware Wall Mount Single Rod Set Motivia Motorized Everything You Need Table of Contents Step 1 - Getting Started....3 Overview - Wall Mount Single Rod Set
More informationINSTALLATION INSTRUCTIONS. Large Flat Panel Wall Mount Model: PRO-2000 Series
INSTALLATION INSTRUCTIONS Large Flat Panel Wall Mount Model: PRO-2000 Series PRO-2000 Series Wall Mount Features: Accommodates large flat screens weighing up to 200 lbs (90.7 kg). Mounting brackets adapt
More informationInstallation Operation Care
Installation Operation Care Vignette Modern Roman Shades Arches and Angles CONTENTS Getting Started: Mounting Types And Window Terminology... 1 Installation Components Needed... 1 Tools And Fasteners Needed...
More informationMenu Board Tilt or Fixed Mount Installation Instructions MDS1T-200, MDS1T-300, MDS1T-400 MDS2T-200, MDS2T-300, MDS2T-400 MDS3T-200, MDS3T-300, MDS3T-400 MDS4T-200, MDS4T-300, MDS4T-400 MDS5T-200, MDS5T-300,
More informationHONEYCOMB SHADES with Continuous Cord Loop
HONEYCOMB SHADES with Continuous Cord Loop GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper installation. Brackets
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Cordless Control with Mounting Bar or Cordless Control with Cassette Table of Contents Step 1 - Getting Started.... 3 Everything You Need A
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System with TrimKit Contents GETTING STARTED Product View... 1 Tools and Fasteners Needed... 2 INSTALLATION Installation Overview...
More informationInstallation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co.
Installation and Operation Manual Ajustable Valance Kits 2502757 2502857 : Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2018
More informationFlat Panel Tilt Wall Mount (GPM-111)
INSTALLATION INSTRUCTIONS Flat Panel Tilt Wall Mount () The tilt wall mount fits most 23 to 30 displays. The is designed to adapt to VESA 200mm/100mm compliant displays. This mount will also adapt to standard
More informationPLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE
HONEYCOMB AND PLEATED SHADE ARCH GETTING STARTED INSIDE MOUNT A few simple tools are required: HALF ARCH INSTALLATION Your half arch has been shipped in the closed osition. When fanned, the rails will
More informationUPLIFT Height Adjustable Standing Desk 3-Leg (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE
UPLIFT Height Adjustable Standing Desk 3-Leg (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL CORDS ARE OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationINSTALLATION INSTRUCTIONS ROLLER SHADES
INSTALLATION INSTRUCTIONS ROLLER SHADES Tools Required: Tape measure, pencil, drill, drill bits, screw driver, step stool or ladder. Note: use a 5/64 drill bit to pre-drill the screw holes (for attachment
More informationInstallation Instructions For The 8850FL Series Mortise eboss
Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity
More informationInstallation Operation Care
Installation Operation Care Duette Honeycomb Shades UltraGlide Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationInstallation Operation Care. Solera Soft Shades EasyRise, UltraGlide, and LiteRise Lifting System
Installation Operation Care Solera Soft Shades EasyRise, UltraGlide, and LiteRise Lifting System CONTENTS GETTING STARTED Product Views...1 Tools and Fasteners Needed...3 INSTALLATION Installation Overview...4
More informationMSP-DCCPGSU Large Screen Static Display Mount
INSTALLATION INSTRUCTIONS Large Screen Static Display Mount The Large Screen Static Display Mount () is a quick disconnect mounting solution for large flat panel displays. The mount self-adjusts for the
More informationMSP-DCCPGTU Large Screen Tilt Display Mount
INSTALLATION INSTRUCTIONS Large Screen Tilt Display Mount The Large Screen Tilt Display Mount is a quick disconnect mounting solution for large flat panel displays. The mount features infinite adjust ability
More informationCellular Shades SLUMBERSHADE. with energy saving blackout sidetracks. Installation & Care Instructions
Cellular Shades SLUMBERSHADE with energy saving blackout sidetracks Installation & Care Instructions 152725 B 9/14/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More informationPRODUCT INFORMATION MANUAL SECTION: 9F-1 DUETTE ULTRAGLIDE LIFTING SYSTEM DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM
DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM Product View Installation Brackets UltraGlide Standard Wand Top-Down/Bottom-Up Duolite REPLACES ISSUE DATE: APPROVED BY: D.ALTIPARMAKOVA PAGE 3 Thank you for
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationMultiTable Mod-E 2 Electric Standing Desk
The Height of Healthy Design MultiTable Mod-E 2 Electric Standing Desk ASSEMBLY INSTRUCTIONS MultiTable Mod-E 2 Electric Standing Desk Frame PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationLARGE FLAT PANEL DISPLAY STATIC MOUNT PST 2000 Series
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL DISPLAY STATIC MOUNT The PST static wall mount accommodates large flat screens weighing up to 200 lbs (90.72kg). The teardrop holes in the mount allow for quick
More informationRolling Curtain door Manual
Rolling Curtain door Manual Installation Maintenance parts Model 944 PHONE 800 448 8979 FAX 800 236 8722 website www.tracrite.com EMAIL tr@tracrite.com ADDRESS 216 Wilburn Road Sun Prairie, WI 53590 This
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.
More informationInstallation Operation Care. Sonnette Cellular Roller Shades. LiteRise Operating System
Installation Operation Care Sonnette Cellular Roller Shades LiteRise Operating System CONTENTS GETTING STARTED: Product View...1 Tools and Fasteners Needed...2 INSTALLATION: Installation Overview...3 Mount
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System Contents GETTING STARTED Product View...1 Tools and Fasteners Needed...2 INSTALLATION Installation Overview...3 Mount the
More informationINSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series
INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option
More informationInstallation Operation Care. Duette Honeycomb Shades EasyRise Lifting System
Installation Operation Care Duette Honeycomb Shades EasyRise Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationRoller Shades MOTORIZED SHADE. Simplicity with rechargeable motor. Installation & Care Instructions
Roller Shades MOTORIZED SHADE Simplicity with rechargeable motor Installation & Care Instructions 152709 C 4/26/2017 GETTING STARTED IMPORTANT: The remote control has not been linked to the shades. Install
More informationInstalling Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image
UX60-RFK-685 Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image Follow these instructions to install brackets on your SMART Board 685ix
More informationMod-E Pro Electric L-Shaped Standing Desk
The Height of Healthy Design Mod-E Pro Electric L-Shaped Standing Desk ASSEMBLY AND OPERATION MultiTable Mod-E Pro Electric L-Shaped Table Base PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationSTEP BY STEP INSTALLATION INSTRUCTIONS. Sheer Shadings. Retractable Cord
STEP BY STEP INSTALLATION INSTRUCTIONS Sheer Shadings Retractable Cord Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience.
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationUPLIFT 2-Leg Height Adjustable Standing Desk
UPLIFT -Leg Height Adjustable Standing Desk Also watch our assembly video http://bit.ly/9ywwh DIRECTIONS FOR ASSEMBLY AND USE TABLE OF CONTENTS PAGE Safety and Warnings Usage Parts List Assembly Instructions
More informationCONTINUOUS CORD LOOP SYSTEM
CONTINUOUS CORD LOOP SYSTEM OPERATING & INSTALLATION INSTRUCTIONS Standard & Heavy-Duty Systems Revised 8/2018 Getting Started A few simple tools are required: Measuring tape Power Drill, drill bits Hex
More informationModel MSPPWRTW Large Flat Panel Single Arm Wall Mount
INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationPleated Shades with Continuous Cord Loop Option
Pleated Shades with Continuous Cord Loop Option Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Thank you for purchasing a Pleated Shade
More informationTauten Tab Tension Screen User Manual
Tauten Tab Tension Screen User Manual Thank you for choosing a Tauten Series Tab Tension screen by Cirrus Screens. Please read through this user manual and understand all instructions before installing
More informationCellular SlumberShade
Cellular SlumberShade with energy saving blackout sidetracks Installation Instructions 152110 1/6/2011 BASICS A few simple tools are required: - Measuring tape - Power drill, drill bits - Hex head and/or
More informationINSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series
INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationSTEP BY STEP INSTALLATION INSTRUCTIONS. Sheer Shadings. Cordless Control
STEP BY STEP INSTALLATION INSTRUCTIONS Sheer Shadings Cordless Control Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience.
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationMODEL 1703E THE CHAMBERLAIN ARM TM INSTALLATION INSTRUCTIONS To be used in conjunction with the Lift-Master Garage Door Operator Owner's Manual
MODEL 1703E THE CHAMBERLAIN ARM TM INSTALLATION INSTRUCTIONS To be used in conjunction with the Lift-Master Garage Operator Owner's Before you begin, please read this ENTIRE instruction manual. One- Piece
More informationLEVOLOR. Sheer Shadings. Persianas traslúcidas Stores diaphanes INSTALLATION OPERATION CARE
LEVOLOR Sheer Shadings Persianas traslúcidas Stores diaphanes INSTALLATION OPERATION CARE INSTALACIÓN FUNCIONAMIENTO CUIDADO INSTALLATION FONCTIONNEMENT ENTRETIEN Sistema operativo sin cordón Système sans
More informationINSTALLATION INSTRUCTIONS Plasma Floor Stand (PFB-2000SB)
INSTALLATION INSTRUCTIONS Plasma Floor Stand (PFB-2000SB) Chief s Plasma Floor Stand is a safe, stable, easy-toinstall modular design solution for digital signage and presentations. Ideal where wall or
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationHardware Installation. Do this first:
1 Do this first: Hardware Installation Need some help? Here s what you ll need: 4 AA Batteries Phillips screwdriver Visit us online. support.remotelock.com We re here to help. 1 (877) 254 5625 support@remotelock.com
More informationUPLIFT 3-Leg Desk Instructions for. Solid Wood Desktops. pictured: 3-leg desk; solid-wood top, with right hand return TABLE OF CONTENTS
UPLIFT 3-Leg Desk Instructions for Solid Wood Desktops pictured: 3-leg desk; solid-wood top, with right hand return TABLE OF CONTENTS PAGE 1 Safety and Warnings 2 2 Usage 2 3 Parts List 3 4 Assembly Instructions
More informationLutron tensioned shade (4.75 inch frame) Chassis Installation Instructions
Lutron tensioned shade (4.75 inch frame) Chassis Installation Instructions Lutron tensioned shade (4.75 inch frame) The Tensioned Shade Chassis Installation Guide is a complement to the enclosed Basic
More informationInstallation Operation Care
Installation Operation Care EasyRise UltraGlide Pirouette Window Shadings EasyRise and UltraGlide Operating Systems and Two-On-One Headrail Shadings CONTENTS Getting Started: Product View...1 Tools and
More informationDUETTE LITERISE SHADES INSTALLATION OPERATION CARE
DUETTE LITERISE SHADES INSTALLATION OPERATION CARE PRODUCT VIEW Installation Brackets Headrail with Fabric-Covered Valance End Cap Middle Rail Bottom Up Shade Bottom Rail Handle Duolite Not Shown: Top
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationINSTALLATION INSTRUCTIONS TOOLS YOU WILL NEED GETTING STARTED
INSTALLATION INSTRUCTIONS HONEYCOMB SHADES TOP-DOWN, MOVABLE ARCH Thank you for your purchase. This shade has been custom built for you from the highest quality materials. To avoid errors and save valuable
More information