Installation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co.
|
|
- Jemimah Hunter
- 5 years ago
- Views:
Transcription
1 Installation and Operation Manual Ajustable Valance Kits : Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2018 Duke Manufacturing Co. All rights reserved. Reproduction without written permission is prohibited. Duke is a registered trademark of the Duke Manufacturing Co. Duke Manufacturing Co N. Broadway St. Louis, MO Phone: Toll Free: Fax: P/N REV A 2/26/2018
2 TABLE OF CONTENTS Inportant Safety Instructions... 2 Tools Required... 3 Parts In Kit... 3 Inspection... 4 Determine Proper Length... 4 Pre Assemble - Top Panel... 4 Pre Assemble - Bottom Panel... 5 Installation... 6 IMPORTANT SAFETY INSTRUCTIONS Throughout this manual, you will find the following safety words and symbols that signify important safety issues with regards to operating or maintaining the equipment. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Indicates Important Information Indicates electrical shock hazard which, if not avoided, could result in death or serious injury and/or equipment damage. Indicates hot surface which, if not avoided, could result in minor or moderate injury. 2
3 TOOLS REQUIRED FOR INSTALLATION Level #2 Phillips Screw Driver 5/16 Nut Driver Tape Measure Cordless Drill 3/8 Nut Driver PARTS IN KIT Pencil Left Side Assembly Anchor Hardware Drill Bit for Anchors Right Side Assembly Top Left Panel Top Right Panel Top Center Panel Bottom Left Panel Bottom Right Panel Bottom Center Panel Panel Assembly Hardware` Top Panel Hardware 3
4 INSPECTION AND PRE-ASSEMBLY Step 1 Verify packaging is not damaged. If product is damaged stop and file claim with trucking company. DETERMINE OVERALL LENGTH Step 4 Determine the overall length of the valance needed for your installation. This Valance is designed to be assembled in increments of 6 without modification between the lengths of 66 and 114 or 100 and 148 depending on the model being installed. Multiple units may be combined to assemble into lengths longer than 148. Step 2 Unpack parts and assemblies carefully. Protect the painted/brown panels from sharp edges and rubbing against other items during assembly. WARNING DO NOT PULL HINGE ARMS OUT FROM HINGE BODY UNTIL INSTRUCTED TO DO SO. DO NOT STAND, KNEEL OR SUPPORT WEIGHT ON PANELS DURING ASSEMBLY. Step 3 Verify fasteners in included hardware bag # are appropriate for the wall structure the valance is being attached to. NOTE: If wall mounting hardware is incorrect, source the correct hardware before continuing. PRE-ASSEMBLE - TOP PANEL Step 5 Remove protective plastic coating from the center stainless panel, a minumum of 10 from both ends. NOTE: Do not remove any of the over wrapped plastic protective covering from the center of the right and left stainless ends to protect the finish. Keep panels on a protective surface at all times
5 ASSEMBLY - continued Step 6 Pre-assemble the top stainless panels to the required length by laying the left and right top assembly panels on a protective surface on the floor at the finished overall distance apart. Lay on a protective service. Note: For overall length see Step 4 Step 8 Using #6 Phillips countersink head screws and locking nuts, supplied in small parts bag, match holes in left and center panel, and bolt together, top and bottom. Repeat for opposite side. Right End Left End Flange is on the bottom when installed Step 7 Set the center panel inside left and right top panels, evenly spaced between the right and left side panels, all upturned flanges orientated the same direction. PRE-ASSEMBLE - BOTTOM PANEL Step 9 Repeat the assembly process for the Painted/beige panels. Remove protective plastic coating from the center painted/beige panel, a minumum of 10 from both ends. NOTE: Do not remove any of the over wrapped plastic protective covering from the painted / beige wood panels except where required for assembly. Keep panels on a protective surface at all times 5
6 ASSEMBLY - continued Step 10 Pre-assemble the bottom painted panels to the required length by laying the left and right lower assembly panels on a protective surface on the floor, finished side down, the ends at the finished overall distance apart. Note: For overall length see Step 4 INSTALLATION Step 1 Verify there is 6 of clear wall space inside of the overall length on each end of the finished valance. Right End Left End Step 11 Set the center panel inside left and right lower panels, evenly spaced between the right and left side panels, all upturned flanges orientated the same direction and secure with #6 Phillips countersink screws and lock nuts. Step 2 Start by mounting the end of the valance closest to the Veggie cabinet; making sure the outside end of the valance is two (2) or more inches from the veggie cabinet when in final location. Step 3 Locate provided template against wall at the correct height above the floor and correct horizontal location for the end of the valance. NOTE: It may be convenient to use the end panels to mark the hole locations when setting the top height of end panels level with ceiling or soffit. Step 4 Making sure template or end panel is vertical, mark the hole locations and outside panel location with a pencil. Template 6
7 Step 5 Using drill bit provided drill five (5) holes and install anchors if required. A minimum of two screws should go through a stud in the wall. Installation and Operation of: Foldup Shroud/Valance INSTALLATION - continued Step 7 If the soffit or ceiling structure is suitable for drilling and attaching screws, square the valance side and front panels. Mark, drill and/or screw anchor angles for upper support brackets to the soffit or ceiling. Drill Five holes Step 8 Attach stainless panel assembly, with the eight (8) x ½ truss head screws through the bracket on the end assemblies and into the threaded inserts on the front panel. Flush end panel with edge of front panel before tightening screws completely. NOTE: The return flange goes to the bottom. This will require two people Step 6 Using the appropriate fasteners from the hardware bag or other fasteners appropriate for the wall structure, attach end assemblies to the wall at the marked/drilled locations. Left End Right End Right End Left End Step 9 Optional on longer assemblies, screw top center panel into soffit through holes in flanges of center panel. 7
8 Step 10 Carefully pull arms of hinges out from main hinge body. The arms are spring loaded and will snap out to the extended position quickly. INSTALLATION - continued Step 12 Slowly pull down on lower panels to close valance. Step 13 Replace Hinge covers if not installed. Step 11 Attach lower painted panel assembly by clipping attached brackets into the arms of the hinge mechanism attached to each end panel. Step 14 Remove any remaining plastic protective film from the Stainless parts and any remaining over wrapped protective covering from the beige wood panels. 8 Duke Manufacturing Co N. Broadway St. Louis, MO Phone: Toll Free: Fax:
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard INSTRUCTION BOOKLET #19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstall Instructions. NewAge Steel Welded Tall Locker
Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x
More informationThanks for shopping with Improvements! Wood Slat Pet Swing Gate Item #441937
Thanks for shopping with Improvements! Wood Slat Pet Swing Gate Item #441937 To order, call 1-800-642-2112 West Chester, OH 45069 0613 If you have questions regarding this product, call 1-800-642-2112
More informationINSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY
NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationWorktop INDEX eight Capacity Unpacking
Pro.0 Series Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationSentinel Electronic Safe Installation Guide
Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard Installation Booklet 19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationMSP-DCCLFSD LCD Flat Screen Swing-Down Mount
INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTION ATV BUMPER/WINCH MOUNT Mount Kit: PN Application: POLARIS 300, 400, 500 and 700 Sportsman
INSTALLATION INSTRUCTION ATV BUMPER/WINCH MOUNT Mount Kit: PN 68573 Application: POLARIS 300, 400, 500 and 700 Sportsman Your safety, and the safety of others, is very important. To help you make informed
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationHardware Box 1 1/4 Diameter x 3/4 Long Bolts 24 1/4 Nylon Lock Nut 24 1/4 Diameter x 3 Long Lag Bolt 8 1/4 Washers 56
Warning: Excessive weight hazard! Use two or more people to move, assemble or install overhead rack to avoid back or other injury. Do not leave children unattended near overhead rack. High risk of injury
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationSAFETY INJURY & HAZARD
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM. Tools Required For Assembly. 6.5mm Masonry Drill Bit
ASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationPFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS
Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationLAN Locker Adjustable Shelves
Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that
More informationSHELTON THERMOSTATIC SHOWER PANEL
SKU(s): 413241 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationAssembly Instructions
RoomScape Furniture System March 2013 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single
More informationASSEMBLY INSTRUCTIONS. enook Pro
ASSEMBLY INSTRUCTIONS enook Pro Product enook Pro for Monitors, 36w Part# EPM3616zz/xx Anthro Corporation 10450 SW Manhasset Dr. Tualatin, OR 97062 Toll-free: 800.325.3841 Fax: 800.325.0045 email: sales@anthro.com
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationAssembly Instructions for Model: VMPL3
Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More informationSolidStep 3.0 OEM INSTALLATION MANUAL
SolidStep 3.0 OEM INSTLLTION MNUL TBLE OF CONTENTS Information 2 Safety 2 Preparation 2 Resources Required 2 Prior to Installation 3 Installation 3 Place ssembly Inside Doorframe 3 djust Transport Lock
More informationINSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800
INSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800 The PAC-800 Lateral Shift Accessory is for use with Chief Model PSM, PST, PRO, PLP, Large Flat Panel Display wall mounts. It can be installed
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More informationADJUST-A-VIEW HALF CIRCLE INSTALLATION INSTRUCTIONS
Omega Mfg. Corporation Two Rivers, WI (800) 874-9594 www.adjustaview.com Proudly Serving Customers Since 1976 Page 1 of 7 MATERIAL LIST ADJUST-A-VIEW User Instructions ADJUST-A-VIEW Installation Instructions
More informationModel MSPPWRTW Large Flat Panel Single Arm Wall Mount
INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H
INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS
More informationShop Style Miter Saw Stand Kit
Quality Power Tool Accessories OWNER S MANUAL Assembled Unit Shown Without Shelves & Wings Assembled With Shelves & Wings Shop Style Miter Saw Stand Kit Model 2850 IMPORTANT Read and understand all safety
More informationCAELI THERMOSTATIC SHOWER PANEL
SKU(s): 300280 CAELI THERMOSTATIC SHOWER PANEL BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationUniversal Cabinet Leveling Base. Installation Instructions
Universal Cabinet Leveling Base MD00_A3 Universal Cabinet Leveling Base Creation Date 2015/10/05 Document Number SJ003A3 Rev A Description Universal Cabinet Leveling Base This manual is proprietary information
More informationINSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1
INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount
More informationWILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard
WILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard INSTRUCTION BOOKLET #13 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS
More informationSB-WM-ART2-L-BL SB-WM-ART2-XL-BL
SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier
More informationSubject: P0052 Bed Locator Installation Instructions
Subject: P0052 Bed Locator Installation Instructions Tools required: Standard drill 1/4" diameter drill bit Phillips head screwdriver Screwdriver 5/16" hex nut driver Tape measure 4' (122 cm) level Power
More informationASSEMBLY & INSTALLATION MANUAL Trim Kit for Evo Affinity 30G
the natural way to cook ASSEMBLY & INSTALLATION MANUAL ( Shown installed to granite topped cabinet ) Copyright 2013 THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND, AND FOLLOW THE INSTRUCTIONS
More informationWILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard
WILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard INSTRUCTION BOOKLET #13 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More informationHZ487300TX Javu 2-Drawer Storage
HZ487300TX Javu 2-Drawer Storage Assembly Instructions For assistance with assembly contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seifurniturestore.com Page
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More information30 wide track Adjustable Tire Rack
30 wide track Adjustable Tire Rack MODEL # SRTRB Patent Pending 1 Installation Support Please Do Not Return This Product To The Store! 1-877-717-RACK (7225) info@strongracks.com If there are any missing
More informationTITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF
TITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF DXST10000 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS
More informationWorktop. Weight Capacity. 100 lbs. 21 Corner Worktop. 48 Worktop. Fits over 2 Cabinets. 72 Worktop. Fits over 3 Cabinets. 200 lbs. 150 lbs.
Bold.0 Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationSolidstep GEN 2 OEM INSTALL MANUAL. Rev: Page 1
Solidstep GEN 2 OEM INSTLL MNUL Rev: 03.23.2017 Page 1 TBLE OF CONTENTS System Information 2 Safety Information 2 Resources Required 3 Installation 3 Solidstep 3 Leg Extension djustment 5 System Information
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationADJUST-A-VIEW QUARTER CIRCLE INSTALLATION INSTRUCTIONS
Omega Mfg. Corporation Two Rivers, WI (800) 874-9594 www.adjustaview.com Proudly Serving Customers Since 1976 Page 1 of 5 MATERIAL LIST ADJUST-A-VIEW User Instructions ADJUST-A-VIEW Installation Instructions
More informationMM750 Installation Instructions
MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on
More informationK.D. LOCKER ASSEMBLY INSTRUCTIONS
K.D. Locker Assembly Instructions PN 0860 K.D. LOCKER Updated /05 ASSEMBLY INSTRUCTIONS These Instructions Cover 3 Types of Lockers: VANGUARD, GUARDIAN AND INVINCIBLE II Contents General Instructions 1
More informationTITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF
TITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF DXST4500 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS TECHNICAL
More informationOctagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More informationAS-TX86. Please read these instructions carefully before using. This model will hold most Flat Panel TVs. Load capacity: 60kg (132Lbs).
AS-TX86 Please read these instructions carefully before using. This model will hold most 52-84 Flat Panel TVs. Load capacity: 60kg (132Lbs). AS-TX86 Information Please read these instructions carefully
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationFSD-4100 LCD Flat Screen Swing-Down Mount
INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile
More informationLARGE FLAT PANEL DISPLAY STATIC MOUNT PST 2000 Series
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL DISPLAY STATIC MOUNT The PST static wall mount accommodates large flat screens weighing up to 200 lbs (90.72kg). The teardrop holes in the mount allow for quick
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More information6 BAY AV CREDENZA WITH DUAL DISPLAY MOUNT
D2/367M2 SSEMLY INSTRUCTIONS 6 Y V CREDENZ WITH DUL DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationContinuous Handrail Kit Installation Instructions
Continuous Handrail Kit Installation Instructions ALUMINUM RAILING SYSTEM Canadian Version Wall Application (see page 2) Railing Application (see page 7) Wall anchors not provided Hardware included: 1x
More informationFrameless Inline Door QCI5250
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationInstallation Instructions Jeep JL Front Grumper Product Number: GR4600 Application: 18+ JEEP JL
! IMPORTANT SAFETY GUIDE Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided the following warnings, safety precautions,
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationFW / FIG Partition Kit(s) Installation Instructions
FW / FIG Partition Kit(s) Installation Instructions This instruction explains how to join 8 in. and 10 in. top piping partitions to FIG and FW merchandisers. Do not remove the shipping braces until the
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More information19 to 39 TV WALL MOUNT - FULL MOTION
19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5
More informationDisplay-Top Apothecary Cabinet. Assembly Instructions. Page 1
Display-Top Apothecary Cabinet Assembly Instructions Page 1 Display-Top Apothecary Cabinet Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
More informationTV WALL MOUNT ASSEMBLY GUIDE RF-TVMLPT01V2
TV WALL MOUNT RF-TVMLPT01V2 For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...4 ASSEMBLY GUIDE Before
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationWINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS
WINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com See garage door owner s manual for
More informationPLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE
HONEYCOMB AND PLEATED SHADE ARCH GETTING STARTED INSIDE MOUNT A few simple tools are required: HALF ARCH INSTALLATION Your half arch has been shipped in the closed osition. When fanned, the rails will
More informationINS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER
INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil
More informationPART #MSP-DCCST Flat Panel Tilt Mount
INSTALLATION INSTRUCTIONS PART # Flat Panel Tilt Mount The Flat Panel Tilt Mount is a quick disconnect mounting solution for flat panel displays. The mount features adjustability between 0 and 15 degrees
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationPlease read through all instructions carefully before you begin. Unpack all materials, making sure all parts are included:
Somfy Motorized Track Installation Instructions Materials Please read through all instructions carefully before you begin. Unpack all materials, making sure all parts are included: Mounting Brackets Track
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More information