Approved Ironmongery for the Railway Environment Version 5

Transcription

1 Approved Ironmongery for the Railway Environment Version 5 Page i

2 Contents Introduction 1 Hinges 2 Door Furniture 4 Door Closers 20 Lockcases 30 Electric Strikes 42 Speech Panels with Call Button 43 Panic Bolts 46 Secure Suite Deadlock 51 Collapsible Gate Device 52 Miscellaneous 55 Key Cabinets and Boxes 59 Typical Doorset Arrangements 60 Suppliers 66 Manufacturers 66 Page ii

3 Introduction DOOR FURNITURE METHODOLOGY This catalogue has been compiled in response to the requirements of the Fire Precautions Act (Sub-Surface Railway Stations) Regulations1401:1989, The EC Construction Products Directive and the Loss Prevention Council s Loss Prevention Standard LPS 1175: Issue 3 Specification for testing and classifying the burglary resistance of building components, strong points and security enclosures. The catalogue must be read in conjunction with Section P21 Ironmongery of the project General Builderswork Specification which defines the performance criteria to be met. The specification of door furniture to be used on the Underground should meet the functional requirement of the room for which it is being specified. An Equipment Room with one access/means of escape will require a door that opens out, if into a public area has a vision panel and a panic function lock (not a panic bolt as for public means of escape). An office may require a mortise latch, mortise locking latch or dead bolt depending on the function, location and security requirement Lockcases are all mortised into the door leaf, rim locks offer little physical security and their use should be avoided. All lockcases are of steel construction, no component part shall have a melting point of less than 850c. The access, escape and security function of each lockcase is fully described. The hand required must be described as viewed from the hinge (butt) side of the door (LH/RH). Face fixed furniture has been catalogued in two varieties, grade 316 stainless steel for post war constructions and BMA gunmetal for pre-war, listed and heritage constructions. Options for the size of pull handle are given for specification according to door leaf size. Closers are shown to cater for the varying conditions with adjustable power sizes. The selection must be appropriate to the requirement. All closers shall be fitted to the non-public side of the door to prevent vandalism. Kicking plates are shown for pre and post war constructions. The selection must be appropriate for the chosen furniture. Barrel bolts inclusive of dust excluding sockets, frame sockets and top receiving plates are shown for use on the inactive leaf of double door sets. Hinges are shown; the number to be used on each door leaf is dependent on leaf size and weight. Design weight loading must be taken into consideration in conjunction with the selected closer. Furniture and signs shall be fitted to doors and frames in accordance with the included illustrations. Manufacturers and suppliers named within this catalogue are identified as capable of meeting the performance requirements described herein. The Part No. reference should be used in conjunction with a Door and Ironmongery Schedule. 5TH EDITION Door Closer range expanded to accommodate selection by door width. New Collapsible Gate Devices added. A Digital Access Key Pad has been added for rooms not subject to public access and other Key pads updated. This edition has been prepared with assistance from Suppliers and Manufacturers without whose detailed understanding of functional requirements and knowledge of architectural ironmongery, assembly of this information would be extremely difficult. The catalogue covers standard door installations within the railway environment and associated auxiliary accommodation. For oversized or non-standard installations advice must be sought from the Discipline Design Engineer. Page 1

4 Hinges Part No. A1 High performance door hinge with concealed bearings Size: 102mm x 89mm x 3mm Material: Austenitic stainless steel Grade (316) BSEN Finish: Standard finish: Satin brushed stainless steel. Alternative: Electrophoretic simulated bronze. Standards: Independently tested to BSEN 1935 Grade 13 Certifire approved and CE marked for fire door usage. Manufacturer s guarantee 25 years. BSEN1935 Test certificate No.TC/02/11/04/C1 CE certificate 1121-CPD-AC0007(S/S) 01/12/02 Maximum adjusted door weight 120kgs. Minimum door thickness 44mm 25 year performance guarantee. Maintenance free concealed bearings. Precision template drilled for use on steel or timber door sets. Screw size: 31mm x No.10 Twinfast Pozihead, M6 x 16mm for metal doors. Markings: TfL-A1 on hinge leaf. Radius corners to special order. Page 2 Select finish complimenting chosen furniture. Select A1 for design loads up to 120kgs and high frequency application.

5 Hinges Part No. A4 High performance door hinge with concealed bearings Size: 114mm x 102mm x 3.4mm - oversize doors Material: Austenitic stainless steel Grade (316) BSEN Finish: Standard finish: Satin brushed stainless steel. Alternative: Electrophoretic simulated bronze Standards: Independently tested to BSEN 1935 Grade 13 Certifire approved and CE marked for fire door usage. Manufacturer s guarantee 25 years. BSEN1935 Test certificate No.TC/02/11/04/C1 CE certificate 1121-CPD-AC0007(S/S) 01/12/02 Maximum adjusted door weight 160kgs. Minimum door thickness 44mm 25 year performance guarantee. Maintenance free concealed bearings. Precision template drilled for use on steel or timber door sets. Screw size: 31mm x No.12 Twinfast Pozihead, M6 x 16mm for metal doors. Markings: TfL-A4 on hinge leaf. Radius corners to special order. Select finish complimenting chosen furniture. Select A4 for design loads up to 160kgs and high frequency application. Page 3

6 Door Furniture Part No. F01 Lever/lever latch furniture un-sprung on un-pierced backplate with solid spindle and security back to back Torx head fixing screws. Size: Lever handle: 150mm x 25mm dia. Backplate: 212mm x 75mm x 2mm Spindle: solid 110mm x 9mm sq. Material: Lever & backplate: (316) BSEN stainless steel Spindle: Mild steel case hardened Fixings: 316 stainless steel male and female back to back bolt through fixings with Torx head. Grub screw spindle fixing. Finish: Lever and backplate: Satin polished Spindle: Zinc passivated Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L01 latch. Page 4 Use in intercommunicating office doors where no security is required. Requires L01 L/R mortise latch.

7 Door Furniture Part No. F04 Lever/lever latch furniture un-sprung on euro pierced backplate with split spindle and security back to back Torx head fixing screws. Size: Lever handle: 2 piece 150mm x 25mm diam. Backplate: 212mm x 75mm x 2mm Spindle: 110mm x 9mm sq. Material: Lever & backplate: (316) BSEN stainless steel Spindle: Mild steel case hardened Fixings: 316 male and female back to back bolt through fixings with Torx head. Grub screw spindle fixing. Finish: Lever and backplate: Satin polished Spindle: Zinc passivated Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L03 and L04 panic locks. Use in secure staff accommodation areas, e.g.: offices, cash handling rooms. Requires L03 L/R or L04 L/R panic lock cases. Page 5

8 Door Furniture Part No. F04X Lever/lever latch furniture un-sprung on euro pierced backplate with solid spindle and security back to back Torx head fixing screws. Size: Lever handle: 150mm x 25mm diam. Backplate: 212mm x 75mm x 2mm Spindle: solid 110mm x 9mm sq. Material: Lever & backplate: (316) BSEN stainless steel Spindle: Mild steel case hardened Fixings: 316 stainless steel male and female back to back bolt through fixings with Torx head. Grub screw spindle fixing. Finish: Lever and backplate: Satin polished Spindle: Zinc passivated Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L12 sash locks Page 6 Use on office, cupboard or storeroom doors where panic escape is not required. Requires L12 L/R mortise sash lock.

9 Door Furniture Part No. F04WC Lever/lever latch furniture un-sprung on thumb turn and release backplate with solid spindle and security back to back Torx head fixing screws. Size: Lever handle: 150mm x 25mm diam. Backplate: 212mm x 75mm x 2mm Spindle: solid 110mm x 9mm sq. Material: Lever & backplate: (316) BSEN stainless steel Spindle: Mild steel case hardened Fixings: 316 male and female back to back bolt through fixings with Torx head. Grub screw spindle fixing. Finish: Lever and backplate: Satin polished Spindle: Zinc passivated Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L13 bathroom locks. Use in staff and public WC doors. Requires L13 bathroom lock. Use in conjunction with L17 mortise deadbolt and F05A escutcheons to allow for isolation during maintenance. Page 7

10 Door Furniture Part No. F13/1/2/3/4 - suffix D for additional pull handle for double door set Lever/pull furniture un-sprung on euro pierced backplate with threaded solid spindle and security back to back Torx head fixings. Size: Lever handle: 150mm x 25mm diam. Lever backplate: 212mm x 75mm x 2mm Pull handle: 150/225/300/400mm x 25mm diam. Pull handle backplate: F13/1-320mm x 75mm x 2mm F13/2-395mm x 75mm x 2mm F13/3-470mm x 75mm x 2mm F13/4-570mm x 75mm x 2mm Spindle: 110mm x 9mm sq. threaded Material: Lever & backplate: (316) BSEN stainless steel Pull handle & backplate: (316) BSEN stainless steel Spindle: Mild steel case hardened Fixings: 316 stainless steel male and female back to back bolt through fixings with Torx head and snake eye bolt. Finish: Lever & back plate: Satin polished Pull & back plate: Satin polished Spindle: Zinc passivated Standards: From approved list, Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L02 panic locks, L14 auto fire panic locks, L16, L19 lockcases or L01 lockcase Page 8 Use on equipment room and public facing doors. Requires L02 L/R mortise sash lock with panic function E deadbolt and latch, L14 L/R mortise sash lock auto-fire panic action deadbolt and latch. or L01L/R, L16 L/R or L19 for security access systems.. Different backplates, sizes and configurations are available in this range. Consult supplier.

11 Door Furniture Part No. F14 Handle arrangement to suit drivers J key on plain un-pierced lever handle plate and lipped external plate with conical key shroud fixed with security back to back Torx fixing screws. Size: Lever handle: 150mm x 25mm diam. Back plate: 212mm x 75mm x 2mm Spindle: Special tapered solid 83mm x 9mm sq. Material: Lever cone & backplate: (316) BSEN stainlesss steel Spindle: Mild steel case hardened Fixings: 316 stainless steeel male and female back to back through fixings with Torx head and snake eye bolt. Finish: Lever & back plates: Satin polished Spindle: Zinc plated Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To suit L01 latch For use on auto-phone kiosks, driver s toilets and access. Requires L01 latch. Alternative configurations are available in this range offering different locking facilities. Consult supplier. Page 9

12 Door Furniture Part No. F15 Lock Bezel to suit driver s J key, on plain plate with conical key shroud Size: Plate: 154mm x 40mm Material: (316) BSEN stainless steel Finish: Satin polished. Fixings: 25mm x No. 6 Torx head countersunk screws Standards: From approved list. Door handle sets manufactured to comply with the requirements of BSEN 1906 grade 4. To act as guide for key on hinged doors and gates to protect keyway. For use on auto phone kiosks, driver s toilets and access. Alternative when F14 door furniture unsuitable. Page 10

13 Door Furniture Part No. WC1 DDA compliant mortise bathroom door furniture Lever latch furniture/double spindle/dda compliant/security back to back Torx head fixing screws. Lever latch furniture, unsprung with backplates, solid spindle and red/green occupied/vacancy bolt indication, external tool release provision in case of emergency. Tested to BSEN 1906 grade. Entry: Free entry in the case of vacancy by lever handle, internal handle provides lifting to vertical position securing WC bolt during occupancy. Exit: Internal single handed action downward to release bolt and latch, enabling exit. Size: Leverhandle 150mm x 25mm dia. Finish: Lever handles Plascoat PPA571 colour compliant with DDA requirement (select from Plascoat range) with advice from Pemises Engineer. Backplates: 212mm x 75mm x 2mm Backplate Satin polished Spindle: Solid 110mm x 9mm sq. Spindle Zinc passivated Material: Lever and backplate: (316) BSEN10088 stainless steel To suit bathroom locks Spindle Mildsteel Fixings: 316 stainless steel male and female back to back bolt through fixings withtorx head external view internal view use in DDA WC s. Requires L18 L/R mortise bathroom lock. Use in conjunction with L17 mortise deadlock and F05 A escutcheons to allow for isolation of toilet during maintenance. Colour range available on request, for clarification consult supplier, Page 11

14 Lock with Emergency Override Part No. LEO1/LEO2 Key entry lock, compliant for use on BSEN 1125 and BSEN 179 panic and emergency exit doors LEO1: surface mounted Material: Bronze body, stainless steel inner components Finish: Chrome plated Cylinder: Round LEO2: recess fitted Material: Stainless steel body, stainless steel inner components Finish: Bright polished Cylinder: Round Operation: By inserting key and turning, then turning lever handle to release multiple panic bolts fitted to the inner face of door. LEO1 - surface mounted LEO2 - recess fitted Use in conjunction with PES2 Panic Exit System and CGD1A active gate lock requiring key access. Key retained facility available, ensures auto-relocking Page 12

15 Lock with Emergency Override Part No. LEO3/LEO4 Key entry lock, compliant for use on BSEN 1125 and BSEN 179 panic and emergency exit doors LEO3: surface mounted Material: Bronze body, stainless steel inner components Finish: Chrome plated Cylinder: Euro-profile LEO4: recess fitted Material: Stainless steel body, stainless steel inner components Finish: Bright polished Cylinder: Euro-profile Operation: By inserting key and turning, then turning lever handle to release multiple panic bolts fitted to the inner face of door. LEO3 - surface mounted LEO4 - recess fitted Use in conjunction with PES2 Panic Exit System and CGD1A active gate lock requiring key access. Key retained facility available, ensures auto-relocking Page 13

16 Door Furniture Part No. F05 A/B/C/D Europrofile pierced escutcheons. Size: A/B 54mm dia. x 7.5mm, C 52mm dia. x 7.5mm, D 45mm x 2mm Finish: F05A - Satin polished F05B - RBMA F05C/D - SSS Material: (316) stainlesss steel or RBMA Gunmetal Fixings F05 A/B Male and female back to back bolt through fixings with Torx head screws F05C/D Suitable fixings to suit door set. F05A F05B F05C Page 14 F05D To be used when no lever furniture is required, RBMA on listed heritage sites. Use in cupboard or passage doors where panic escape is not required. Use with L17 mortise deadbolt. F05A/B bolt through back to back. F05C/D supplied as single items when only external key access required.

17 Door Furniture Part No. F08 External access device with Europrofile aperture (available with either knob or lever handle). Compliant for use on BSEN179 and BSEN 1125, panic and emergency exit doors. Use in conjunction with Panic Bar F07 and optional free or locked configuration is required. Access from outside available either by inserting key and turning knob or, in unlocked mode, by turning knob only. Page 15

18 Door Furniture Part No. F22 Lever/lever furniture un-sprung lever handles on roses complete with plain spindle and fixing screws. Size: Finish: Lever handle: 120mm x 20mm Lever handle: RBMA Rose: 54mm diam. x 7mm Rose: RBMA Spindle: solid 9mm sq. x 100mm Spindle: Zinc passivated Material: Standards: Lever handle: Gunmetal From approved manufacture list Rose: Gunmetal Spindle: Mild steel To suit L01 latch locks Fixings: Male and female back to back bolt through fixings with Torx head. Page 16 For listed/ heritage/ pre-war constructions. Use in intercommunicating office doors where no security is required. Requires L01R/Lmortise latch.

19 Door Furniture Part No. F25 Lever/lever furniture un-sprung lever handles on roses complete with split spindle and fixing screws. 1 pair euro profile pierced escutcheons complete with fixing screws. Size: Lever handle: 120mm x 20mm Rose: 54mm diam. x 7mm Spindle: 9mm sq. x 100mm 2 piece Escutcheon: 54mm diam. x 7mm Material: Lever handle: Gunmetal Rose: Gunmetal Spindle: Mild steel Escutcheon: Gunmetal Fixings: Male and female back to back bolt through fixings with Torx head. Finish: Lever handle: RBMA Rose: RBMA Spindle: Zinc passivated Escutcheon: RBMA Standards: From approved manufacture list To suit L03 L/R or L04 L/R mortice sash lock For listed/ heritage/ pre-war constructions. Use on office, cupboard or storeroom doors where panic escape is required. Requires L03 L/R or L04 L/R mortice sash lock Page 17

20 Door Furniture Part No. F25X Lever/lever furniture un-sprung lever handles on roses complete with solid spindle and fixing screws. 1 pair euro profile pierced escutcheons complete with fixing screws. Size: Lever handle: 120mm x 20mm Rose: 54mm diam. x 7mm Spindle: solid 9mm sq. x 100mm Escutcheon: 54mm diam. x 7mm Material: Lever handle Gunmetal Rose Gunmetal Spindle Mild steel Escutcheon Gunmetal Fixings: Male and female back to back bolt through fixings with Torx head. Finish: Lever handle Real BMA Rose Real BMA Spindle Zinc passivated Escutcheon Real BMA Standards: From approved manufacture list To suit L12 sash locks For listed/ heritage/ pre-war constructions. Use on cupboard or storeroom doors where panic escape is not required. Requires L12 L/R mortise lock deadbolt and latch. Page 18

21 Door Furniture Part No. F44/1/2/3 Lever/pull furniture un-sprung lever handles on roses complete with split spindle and fixing screws. 1 pair euro profile pierced escutcheons complete with fixing screws. Use suffix D for additional pull handle for double leaf doorset. Size: Lever handle: 120mm x 20mm Rose: 54mm diam. x 7mm Spindle: solid 9mm sq. x 100mm Pull handle: 150/225/300mm x 20mm Escutcheon: 54mm diam. x 7mm Finish: Lever handle: Real BMA Rose: Real BMA Spindle: Zinc passivated Pull handle: Real BMA Escutcheon: Real BMA Material: Lever handle: Gunmetal Rose: Gunmetal Spindle: Mild steel Pull handle: Gunmetal Escutcheon: Gunmetal Standards: To TfL specification from approved manufacture list To suit L02 panic locks, L16, L19 auto fire panic locks or L01 lockcase Fixings: Male and female back to back bolt through fixings with Torx head and snake eyed bolt. Use on equipment room and public facing doors. Requires L02 L/R mortise sash lock with panic function E deadbolt and latch, L14 L/R mortise sash lock auto-fire panic action deadbolt and latch. or L01L/R, L16 L/R or L19 for security access systems.. Different backplates, sizes and configurations are available in this range. Consult supplier. Page 19

22 C6 DOOR CLOSER Cam Action slide arm closer for mounting pull side of door Cam action door closer with full cover, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 1-4 to suit doors up to 1100mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C6 with roundel Page 20 Closers are always to be fixed to the inside (unprotected) face of door leaf.

23 C7 DOOR CLOSER Cam Action slide arm closer for mounting push side of door Cam action door closer with full cover, angle bracket, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 1-4 to suit doors up to 1100mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses) stainless steel (sss) Marking: C7 with roundel Closers are always to be fixed to the inside (unprotected) face of door leaf. Page 21

24 C8 DOOR CLOSER Cam Action electro-magnetic hold open slide arm closer for mounting pull side of door Cam action door closer with full cover, electro-magnetic hold open slide channel and concealed fixings. Standards: CE marked to BSEN1155, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 1-4 to suit doors up to 1100mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C8 with roundel Page 22 Closers are always to be fixed to the inside (unprotected) face of door leaf. Use on doorsets that are likely to be otherwise wedged open e.g. intercommunicating doors in frequent use. Needs wired into fire alarm system and the Fire Engineer should be advised.

25 C9 DOOR CLOSER Cam Action electro-magnetic hold open slide arm closer for mounting push side of door Cam action door closer with full cover, electro-magnetic hold open slide channel and concealed fixings. Standards: CE marked to BSEN1155, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 1-4 to suit doors up to 1100mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C9 with roundel Closers are always to be fixed to the inside (unprotected) face of door leaf. Use on doorsets that are likely to be otherwise wedged open e.g. intercommunicating doors in frequent use. Needs wired into fire alarm system and the Fire Engineer should be advised. Page 23

26 C10 DOOR CLOSER Cam Action slide arm closer for mounting pull side of door Cam action backcheck and delayed action door closer with full cover, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 2-5 to suit doors up to 1250mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C10 with roundel Page 24 Closers are always to be fixed to the inside (unprotected) face of door leaf.

27 C11 DOOR CLOSER Cam Action slide arm closer for mounting push side of door Cam action backcheck and delayed action door closer with full cover, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 2-5 to suit doors up to 1250mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C11 with roundel Closers are always to be fixed to the inside (unprotected) face of door leaf. Page 25

28 C12 DOOR CLOSER Cam Action slide arm closer for mounting pull side of door Cam action backcheck and delayed action dooor closer with full cover, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 5-7 to suit doors up to 1400mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C12 with roundel Page 26 Closers are always to be fixed to the inside (unprotected) face of door leaf.

29 C13 DOOR CLOSER Cam Action slide arm closer for mounting push side of door Cam action backcheck and delayed action door closer with full cover, concealed fixings and cushioned limit stay Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 5-7 to suit doors up to 1400mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver (ses), stainless steel (sss) Marking: C13 with roundel Closers are always to be fixed to the inside (unprotected) face of door leaf. Page 27

30 C14 DOOR CLOSER Tandem closers for mounting pull/push side of door Tandem mounted backcheck door closers with mounting plate and tandem spindle connection. Standards: CE marked to BSEN1154, Certifire approved for timber fire doors (2 hours) and metal fire doors (4 hours). Size: power adjustable size EN 4-7 to suit doors up to 1600mm. Position and environment of door must be taken into consideration when selecting closer. Finishes; silver Marking: C14 with roundel Page 28 Closers are always fixed to the inside (un-protected / fire protected) face of door leaf, fitted transom to push side of door. Auxiliary brackets for restricted soffit conditions may be required - consult with supplier.

31 C15 DOOR CLOSER Closer for mounting pull/push side of door Anti corrosive coated coated back check closer with mounting plate suitable for internal and external use. Standards: CE marked to BSEN1154. Certifire approved for timber door (2 hours) and metal doors (4 hours) Material: Closer body : Aluminium alloy qualities grade AL Si6 Cu4. Main arm : Steel zinc plated. Stainless steel ball pin Adjustment arm: consisting of fixing bracket, threaded pin and threaded stainless steel nut. Fixings: : stainless steel Drain holes in the closer housing guarantee that water jets flow off. All parts are triple lacquered. Size Power adjustable size EN3-6 to suit doors up to 1400mm. Position and environment of door must be taken into consideration when selecting closer. Finishes: silver Marking: C15 with roundel Closers are always fixed to the inside (un-protected / fire protected) face of door leaf, fitted transom to push side of door. Auxiliary brackets for restricted soffit conditions may be required - consult with supplier. Page 29

32 Lock Cases Part No. L01 L/R Mortise latch. Latch bolt operated by lever handle from inside or outside. Size: Face plate: 235mm x 24mm radius end, 65mm backset Material: Case: Heavy duty mild steel Faceplate: 316 stainless steel Strikeplate: 316 stainless steel Finish: Case: Galvanised Faceplate: Satin brushed Strikeplate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested BSEN1634. Latch case body to be enclosed. Solid follower to accept 9mm sq. bar spindle. To be operated by F01 or F022 furniture sets and F13 or F44 for security access systems. Marking: TfL-L01 Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Page 30 Use in intercommunicating office doors where no security is required. Requires F01 or F22 lever/lever furniture - F13 or F44 for security access systems. F14 or F15 for drivers J key. Requires correct MLSSK strike.

33 Lock Cases Part No. L02 L/R Mortise sash lock with panic escape function E. Escape: Escape from inside at all times by depressing lever handle. Access: Access from outside only available by inserting key and turning to withdraw deadbolt on turns one and two with the latch bolt on the third Security: Re-entry after escape only possible with key. Size: Face plate: 235mm x 24mm radius end, 65mm backset, centres 72mm Material: Case: Heavy duty mild steel Face plate: 316 stainless steel Finish: Case: Galvanised Face plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. Solid follower to accept 9mm sq. bar spindle. To be operated by F13 and F44 furniture sets. Marking: TfL-L02 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Use in equipment room, store room and public facing doors. Requires F13/1/2/3/4 or F44/1/2/3/4 pull/lever handle furniture. Requires correct MLSSK strike. Page 31

34 Lock Cases Part No. L03 L/R Mortise sash lock with panic escape function B (open out) Escape: Escape from inside at all times by depressing lever handle. Access: Access from outside only available by inserting key and turning to withdraw deadbolt on turn one and turn two activates the outside lever. Free access when unlocked. Security: Re-entry after escape only possible with key turned to activate lever handle. Size: Face plate: 235mm x 24 mm radius end, 65mm backset, centres 72mm Material: Case: Heavy duty mild steel Face plate: 316 stainless steel Strike plate: 316 stainless steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. Euro cylinder cut-out. Split follower to accept 9mm sq. bar spindle. To be operated by F04 and F25 furniture sets. Marking: TfL-L03 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Right - panic open out DIN Left - panic open out Page 32 Use in internal staff accommodation. Requires F04 or F25 lever/lever furniture. Requires correct MLSSK strike.

35 Lock Cases Part No. L04 L/R Mortise sash lock with panic escape function B (open in) Escape: Escape from inside at all times by depressing lever handle. Access: Access from outside only available by inserting key and turning to withdraw deadbolt on turn one and turn two activates the outside lever. Free access when unlocked. Security: Re-entry after escape only possible with key turned to activate lever handle. Size: Face plate: 235mm x 24mm radius end, 65mm backset, centres 72mm Material: Case: Heavy duty mild steel Face plate: 316 stainless steel Strike plate: 316 stainless steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. Euro cylinder cut-out. Split follower to accept 9mm sq. bar split spindle. To be operated by F04 and F25 furniture sets. Marking: TfL-L04 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in Use in internal staff accommodation doors Requires F04 or F25 lever/lever furniture. Requires correct MLSSK strike. Page 33

36 Lock Cases Part No. L12 L/R Mortise sash lock. Escape: Only possible when the deadbolt is not engaged, latch bolt operated by depressing lever handle. Access: Access from outside only available by inserting and turning key to unlock the deadbolt Free access when unlocked.. Security: Re-entry after escape possible by depressing lever handle Size: 235mm x 24mm radius end, 65mm backset, centres 72mm Material: Case: Heavy duty mild steel Face plate: 316 stainless steel Strike plate: 316 stainless steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN CE marked. Fire tested BSEN1634. Latch case body to be enclosed. Euro cylinder cut-out. Solid follower to accept 9mm sq. bar spindle. To be operated by F04X and F25X furniture sets. Marking: TfL-L12 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Page 34 Use in cupboard, store room or office doors where panic escape is not required. Requires F04x or F25x lever/lever handle. Requires correct MLSSK strike.

37 Lock Cases Part No. L13 L/R Mortise bathroom lock. Escape: Only possible when the deadbolt is not engaged, latch bolt operated by depressing lever handle. Access: Access from outside only available by depressing lever handle,deadbolt can be withdrawn in an emergency by turning external release. Security: None. Size: 235mm x 24mm radius end, 65mm backset, centres 78mm Material: Case: Heavy duty mild steel Face plate: 316 stainless steel Strike plate: 316 stainless steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. No cylinder cut-out. Solid follower to accept 9mm sq. bar spindle. To be operated by F04WC and F25WC furniture sets. Marking: TfL-L13 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Use in staff and public WC s. Requires F04WC or F25WC lever/lever handle. Can be used in conjunction with L17 mortise dead lock to allow isolation of toilets for maintenance. Requires correct MLSSK strike. Page 35

38 Lock Cases Part No. L14 L/R Mortise sash lock with auto-fire panic escape function E. Escape: Escape from inside at all times by depressing lever handle. Access: Access from outside only available by inserting key and turning to withdraw deadbolt and latchbolt. Security: On closing the door, the latch bolt auto-fires the into deadbolt function, re-entry only possible by inserting and turning key from outside. Size: 235mm x 24mm radius end, 65mm backset, centres 72mm Material: Face plate: 316 stainless steel Case: Heavy duty mild steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. Euro cylinder cut-out. Solid follower to accept 9mm sq. bar spindle. To be operated by F13 and F44 furniture sets. Marking: TfL-L14 on face plate Must be used in conjunction with MLSSK stainless steel box striker. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Page 36 Use in access doors to staff accommodation, equipment and secure rooms e.g.: lobby, fire exit or where additional security is required Requires F13/1/2/3/4 or F44/1/2/3/4 lever pull furniture. Requires correct MLSSK strike.

39 Lockcases Part No. L16 Mortise auto deadlatch Escape: Escape from inside at all times by depressing lever handle. Access: Access from outside only available by inserting key and turning to withdraw dead bolt and latchbolt. Security: On closing the door the deadlatch/latchbolt operates. Re-entry only possible by inserting and turning key from outside. Size: 235mm x 24mm radius end, 65mm backset, centres 72mm Material: Face plate: 316 stainless steel Case: Heavy duty mild steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case body to be enclosed. Euro cylinder cut-out. Solid follower to accept 9mm sq. bar spindle. To be operated by F13 and F44 furniture sets. Marking: TfL-L16 on face plate To be used in conjunction with EDS 1 stainless steel antithrust snib, prevents latch bolt manipulation. IL1 Intumescent 3 part lock protection pack available. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Use in office door where access control is required Requires EDS1 (2013) electronic release, F13/1/2/3/4, F44/1/2/3 or F14 door furniture. Requires correct MLSSK strike. Page 37

40 Lockcases Part No. L17 Mortise dead lock Escape: Only possible when the deadbolt is not engaged. Deadbolt operated by turning the key to unlock. Access: Access from outside only available by inserting the key and turning to withdraw the deadbolt. Security: The deadbolt functions only through the use of the key. Size: 235mm x 24mm radius end, 65mm backset Material: Face plate: 316 stainless steel Case: Heavy duty mild steel Strike plate: 316 Sstainless steel Finish: Case: Galvanised Face plate: Satin brushed Strike plate: Satin brushed Standards: DIN and Modular lock range tested to BSEN and escape function BSEN 179. CE marked. Fire tested EN1634. Latch case to be enclosed. Euro cylinder cut-out Marking: TfL-L17 on face plate IL1 intumescent 3 part lock protection pack available Page 38 Use in cupboard doors or doors where panic escape is not required. Use with F05 A/B/C/D escutcheons. Can be used in conjunction with L13 amd L18 mortise bathroom lock to allow isolation of toilets for maintenance. Requires correct MLSSK strike - consult supplier.

41 Lockcases Part No. L18 L/R Mortise bathroom lock Escape: Access: Security: Latch and deadbolt operated by depressing lever handle. Access from outside only available by depressing lever handle, deadbolt can be withdrawn in an emergency by turning external release. None Size: Face plate 228mm x 25mm radius end, 56mm backset, centres 78mm Material: Face plate Stainless steel Case Heavy duty mild steel Finish: Face plate Satin brushed Case: Mild steel Hammerite Standards: BS 8300 Document M. Latch case body to be enclosed No cylinder cut-out Fixings Solid follower to accept spindle ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Use in staff and public WC s. Requires WC1 lever/lever handle. Can be used in cojunction with L17 mortise deadlock to allow isolation of toilet for maintenance Requires correct MLSSK strike. Page 39

42 Lock Cases Part No. L19 L/R Mortise sash lock with deadlocking latch panic escape function E Escape: Access: Security: Escape from inside when latched at all times by depressing lever handle. Access from outside only available by inserting key and turning to withdraw deadbolt, when fully key secured. Normal action is latch turn to open, when manned. re-entry after escape only possible with key. Size: Face plate 235mm x 24mm radius forend, 65mm backset, centres 72mm. Material: Face plate Stainless steel Case Heavy duty mild steel Finish: Face plate Satin brushed Case: Galvanised Standards: DN and Modular lock range CE marked and tested to BSEN and panic escape BSEN 179. Fire tested EN1634. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Page 40 Use on public facing doors to staff accommodation, where additional security is required. Dead latch prevents unlawful manipulation and deadbolt gives additional out of office security. Requires F13 or F44 furniture and either EDS1 (2013) electric strike, deadlock version or MLSSK manual strike - consult supplier.

43 Mortice strike plate Part No. MLSSK 44/54 Size: 235mm x 40/50mm Material: 316 stainless steel Fixings: Use suitable Torx head screws Finish: Satin brushed Anti-rattle adjustment available on 54mm size. Powder coated antique bronze for heritage doors opening outwards in public areas only. Use with all mortice lockcases. Page 41

44 Electric strikes Part No. EDS 1 (2013) 44/54 High Security Escape: By using internal lever handle Access: Access from outside only available by inserting key and turning to withdraw the latchbolt. Security: Self locking. For use in areas with electronic access systems. Size: Stainless plate: 326mm x 40/50mm Material: Stainless steel face plate and steel and cast release Fixings: 4 x no. 6 x 32mm timber screws, EDS1BP (2013) 44/54 bridging plate sets available for steel door sets Finish: Satin Stainless Steel Standards: CE marked fire rated door strike with a break open pressure of 8000 Newton s (N) with adjustable latch slide to ensure the door can close tightly. Fail locked strikes open when the current is applied and lock automatically when the power is removed. Strikes are optionally available with a built in micro switch to monitor latch bolt engagement, adjustable power consumption 6 volts 24 volts giving 100% duty ratio. To suit frames and replace approved strikes MLSSK, for doors requiring access control and door entry systems e.g. manned Control Rooms and offices. Page 42 Use with L01 or L16 lockcases for latch only, deadlocking available using L02 or L19 lockcases when office is left unmanned. Consult supplier for alternative models.

45 Digital access key pad Part No. DKP Size: w 120mm x h 225mm Fixings: use suitable 4 x no.6 x 32mm torx head screws Finish: satin brushed 12 SWG stainless steel vandal resistant key pad,. Used for access to back of house areas by staff and others where non key access is required, in conjunction with EDS1 (2013) electric strike. Advise HF engineer and electrical engineer and take advice of lock and release requirement. Available flush fitted or with Stainless Surface Housings, add SSH, consult supplier Page 43

46 Speech panels with call button Part No. ASP/ASVP Size: 389mm x 120mm Material: 316 stainless steel Fixings: Use suitable 6 x No.6 32mm Torx head screws Finish: Satin brushed 12swg stainless steel vandal-resistant audio, surface mount, includes illuminated/tactile CALL button, SPEAK NOW LED and DOOR OPEN LED. Fulfilling requirements and duties required under the Equality Act by satisfying the recommendations of BS 8300 and Approved Document M. Part No. VRVDDA1 - video entry panel Part No. ASP audio entry panel Part No. ASVP - audio video entry panel Use adjacent to Control Room doors in conjunction with EDS 1 (2013) electric strike. Advise HF engineer and electrical engineer and take advice of lock and release requirement. Available flush fitted or with Stainless Surface Housings, add SSH, consult supplier Page 44

47 Speech panels with call button Part No. AVKPSP/AVACSP Size: AVKPSP 470 x 120 / AVACSP 389mm x 120mm Material: 316 stainless steel Fixings: Use suitable 6 x No.6 32mm Torx head screws Finish: Satin brushed 12swg stainless steel vandal-resistant audio, surface mount, includes illuminated/tactile CALL button, SPEAK NOW LED and DOOR OPEN LED. fulfilling requirements and duties required under the Equality Act by satisfying the recommendations of BS 8300 and Approved Document M. Part No. AVKPSP - audio video entry panel with keypad Part No. AVACSP - audio video entry panel with access control Use adjacent to Control Room doors in conjunction with EDS 1 (2013) electric strike. Advise HF engineer and electrical engineer and take advice of lock and release requirement. Available flush fitted or with Stainless Surface Housings, add SSH, consult supplier Page 45

48 Panic Bolts Part No. F06 Mortise panic actuator Classification: B A A Surface mounted panic latch actuator with euro profile mortise nightlatch to BSEN 1125 C.E.N Compliant and C.E. marked Fire tested to BSEN Self handing Fixing kits for both timber and steel door sets available Fire door tested (Must be used with LU/ILI intumescent 3 part lock protection pack) Finish: satin stainless steel Material: chrome passivated and stainless steel coat effect ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Right - panic open out DIN Left - panic open out Use on single escape door open out or active leaf of double door set External access by external single cylinder and pull or, where free access is required on internal doors, by external access device F08 Page 46

49 Panic Bolts Part No. F07 Two point panic bolt Classification: B A A Surface mounted single panic bolt with auto-fire top trip catch to BSEN 1125 C.E.N Compliant and C.E. marked Self handing Fixing kits for both timber and steel door sets available Fire tested to BSEN1634 Finish: satin stainless steel Material: chromium passivated and stainless steel coat effect ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Right - panic open out DIN Left - panic open out Use on passive leaf of double leaf fire exit in conjunction with F06. Page 47

50 Emergency Exit Device Part No. EED 1 Surface mounted, single-point emergency escape device to BSEN 179, CE marked Classification: B A B For use on a single leaf or the active leaf of double doors and gates where a single panic escape leaf only is required. Keeps and fixings are available for timber or steel doors. Escape: Escape from inside at all times by depressing lever handle. Access: Optional access from outside available by inserting key and turning to withdraw deadbolt. Security: Re-secures each time upon door closure. Handing: Handing and opening direction required. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Standard keeps Page 48 Outward opening Use on non-public escape doors and gates with cylinder or J key. Different strike plates available, consult supplier.

51 Panic Exit Latch Part No. PEL 1 L/R Surface mounted panic latch actuator with 9mm follower operating a mortice latch, accredited to BSEN 1125, CE marked Classification: A A For use on a single leaf or the active leaf of double doors where a single panic escape leaf only is required. Supplied complete with panic exit latch, 9mm spindle, fixings and keep for a timber door (fixings for steel doors are available) Escape: Escape from inside at all times by depressing panic bar. Access: Optional access from outside available by inserting key and turning to withdraw latch. Handing: Handing is required Security: Re-latches automatically upon door closure. ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Right - panic open out DIN Left - panic open out Use in conjunction with L01 and L16 lockcases Page 49

52 Panic Exit System Part No. PES 2 L/R Surface mounted, 2-point panic escape device to BSEN 1125, CE marked Classification: B A A For use on a single leaf or both the active and inactive leaf of double doors with plain meeting stiles. Supplied with fiings and keeps for a timber door (fixings for steel doors are available). Escape: Escape from inside at all times by depressing panic bar. Access: Optional access from outside available by inserting key and turning to withdraw deadbolt then to turn lever hand to release the bolts. Security: Re-secures each time upon door closure. Standard keeps Top keep & strike Dust free floor keep ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Right - panic open out DIN Left - panic open out Use on final exit requiring high security and leading to a public space.. Can be used on the passive leaf of double leaf fire exit in conjunction with PEL 1 Page 50

53 Secure Suite Deadlock Part No. SSD 3 / 5 Surface mounted, encased multi-point deadlocking device to BSEN 179, CE marked Key release deadlock and lever handle entry with an internal lever handle to provide a one-handed means of exit,for single leaf doors. Supplied with fixings and keeps for a timber door (fixings for steel doors are available). Escape: Escape from inside at all times by depressing lever handle. Access: By inserting a key and turning to unlock then turning the lever handle to release the multiple bolts. Security: Re-secures automatically each time the door reaches it s closed position. Handing: Handing and opening direction is required (see chart below) Standard keeps Top keep & strike ARROW INDICATES DIRECTION OF TRAVEL OR ESCAPE DIN Left - panic open in DIN Right - panic open in DIN Right - panic open out DIN Left - panic open out Centre keep Protected external key cylinder and handle entry Dust free floor keep Page 51

54 Collapsible gate device Part No. CGD 1A L/R All steel construction fitted to main entrance external gates slide trigger set for final auto locking gate. Escape: Single handed emergency escape inside by depressing lever handle (red). Access: Optional acess from outside of auto fire active leaf using leo 1/2/3/4 Security: Two point manual locking on secondary gate. Auto firing three point locking on final exit / entrance gate. Optional: Single and double gates can use combination of either option Finish: dark grey hammerite lockcase and saddles, sss bars and bolts red handle. Handing: Handing and opening direction is required (see chart below) Size: 75mm x 175mm x 25mm Material: Mild steel with stainless steel rods/bars Fixings: Lockcase M8 hex / Saddles M6 hex Right hand inside Left hand inside Page 52 Optional external key access with LEO 1/2/3/4 Internal handle with sprung hinged door box shrouds and cover plates available for additonal security. Gates are located in stainless housings secured with budget / key suited locks when open - consult supplier

55 Collapsible gate device Part No. CGD 1B L/R All steel construction fitted to main entrance external gates slide trigger set for final auto locking gate. Escape: Single handed emergency escape inside by depressing lever handle (red). Access: Optional acess from outside of auto fire active leaf using leo 1/2/3/4 Security: Two point manual locking on secondary gate. Auto firing three point locking on final exit / entrance gate. Optional: Single and double gates can use combination of either option Finish: dark grey hammerite lockcase and saddles, sss bars and bolts red handles. Handing: Handing and opening direction is required (see chart below) Size: 75mm x 175mm x 25mm Material: Mild steel with stainless steel rods/bars Fixings: Lockcase M8 hex / Saddles M6 hex Right hand inside Left hand inside Optional external key access with LEO 1/2/3/4 Internal handle with sprung hinged door box shrouds and cover plates available for additonal security. Gates are located in stainless housings secured with budget / key suited locks when open - consult supplier Page 53

56 Collapsible Gate Device Part No. CGD 2 L/R Deadlocking twin-hook lock for securing collapsible sliding gates Size: Face plate: 700mm x 40mm x 5mm Lock body: 58mm x 88mm x 22mm Box keep 700mm x 40mm x 5mm Material: Case: Heavy duty mild steel Face plate: Heavy duty mild steel Box keep: Heavy duty mild steel Finish: Case: Zinc passivated Face plate: Zinc passivated Box keep: Zinc passivated Fixings: Lock body: M8 Hook lock body to be enclosed. All steel construction, for retro-fitting to collapsible gates, handles can be provided on either side providing egress. Supplied with fixings and box keep. Escape: Single handed emergency escape from inside by depressing emergency lever handle (green). Access: Access from outside is available by inserting key and turning the lever handle to withdraw the bolts. Security: The twin-hook locks latch and deadlock automatically upon gate closure. Right hand inside Left hand inside Optional external key and lever handle entry. Green lever handle for emergency release. Page 54

57 Miscellaneous Part No. G3/G4/G2A Barrel bolt set. Heavy duty 16mm barrel bolt with floor socket and flush door staple for open-in or open-out passive leaf of double door set. Finish: Mild steel PPC finish or black Hammerite. Fixings to be appropriate to the doorset construction. Specify keeps as required from below G3 Barrel bolt G4 Dust excluding socket G2A Flush door staple Page 55

58 Miscellaneous Part No. K4/K5 Kick plates K4 Material: BSEN grade (316) stainless steel x 1.5mm - door width (less stops) x 400mm (to BS8300) - secure by Torx head screws. K5 Material: Real bronze metal antique on gun metal x 1.5mm - door width (less stops) x 400mm (to BS8300) - secure by Torx head screws Page 56

59 Miscellaneous Part No. F1/F2 Finger plates F1 (standard) Material: BSEN grade1.440 (316) stainless steel 300mm x 75mm x 1.5mm, complete with fixings for timber F2 (large) Material: BSEN grade 316 stainless steel 470mm x 75mm x 1.5mm, complete with fixings for timber Please specify when ordering: 316 stainless steel, radius corners, satin finish, etc. Other sizes and finishes are available Page 57

60 Miscellaneous Part No. K1/K2/K3/K6 Door stops, coat hook and door selector K1 Wall door stop - BSEN grade (316) stainless steel K2 Floor door stop - BSEN grade (316) stainless steel K3 Door mounted hat and coat hook - BSEN grade (316) stainless steel K6 Door selector enables a pair of self closing doors with rebated meeting stiles or overlapping astragal to close in the correct sequence automatically, no matter which door is opened first. Tested to BSEN1158. BSEN grade (316) stainless steel. Suitable timber doors of any width up to 1220mm (4 0 ) per door and all standard thicknesses and rebate sizes. K1 wall door stop K2 floor door stop K3 hat and coat hook K6 door selctor for double doors with rebated meeting stiles Page 58 Products are shown to advise. Many variations are available to suit position and environment - consult with supplier.

61 Key Cabinet and Boxes CAB 1: Size: 550mm x 380mm x 80mm Standard capacity 100. Other sizes available. CAB 2: Size: 175mmH x 140mmW x 50mm (Excluding cylinder protrusion) Key box with single hook for restricted access key/keys. CAB 3: Size: 153mm x 123mm x 40mm Break glass box for emergency access. CAB 2 - single hook for restricted access key CAB key capacity CAB 3 - break glass box for station emergency keys Key access can be under Site Master System, keyed alike or differs. Products are shown to advise. Many variations are available to suit position and environment - consult with supplier. Page 59

62 Typical Doorset Arrangements SINGLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE Furniture - L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash lock autofire panic action deadbolt and latch F13/1/2/3/4 on pierced backplates or F44/1/2/3/4 on escutcheons and roses pull/lever handles A1/SS/BGMA or A4/SS/BMA hinges C7 overhead door closer K4 or K5 kick plates Page 60 note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8

63 Typical Doorset Arrangements SINGLE LEAF FD60 EQUIPMENT ROOM DOOR WITH GLAZING APERTURE Furniture - L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash lock autofire panic action deadbolt and latch F13/1/2/3/4 on pierced backplates or F44/1/2/3/4 on escutcheons and roses pull/lever handles 1.5 pair A1/SS/BGMA or A4/SS/BMA hinges (for doors in excess of 910x21oo use 2 pairs) note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8 Page 61

64 Typical Doorset Arrangements DOUBLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE Furniture - L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash lock autofire panic action deadbolt and latch F13/1/2/3/4(D) on pierced backplates or F44/1/2/3/4(D) on escutcheons and roses pull/ lever handles 3 pair A1/SS/BMA or A4/SS/BMA hinges (for door in excess of 910x2100 use 4 pairs) 1 pair C7 overhead door closers 1 pair G3/G4/G2C barrel bolt sets K4 or K5 kick plates Page 62 note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8

65 Typical Doorset Arrangements DOUBLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE Furniture - L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash lock autofire panic action deadbolt and latch F13/1/2/3/4(D) on pierced backplates or F44/1/2/3/4(D) on escutcheons and roses pull/ lever handles 3 pair A1/SS/BMA or A4/SS/BMA hinges (for door in excess of 910x2100 use 4 pairs) 1 pair C7 overhead door closers 1 pair G3/G4/G2C barrel bolt sets K4 or K5 kick plates note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8 Page 63

66 Typical Doorset Arrangements SINGLE LEAF FD60 FINAL EXIT Furniture - mortise panic action deadlatch F06 panic bar assembly with or without europrofile pierced cylinder pull. 1.5 pair A1/SS or A4/SS hinges (for door in excess of 910x2100 use 2 pairs) C7 overhead door closers K4 or K5 kick plates Page 64 note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8

67 Typical Doorset Arrangements DOUBLE LEAF FD60 FINAL EXIT Furniture - mortise panic action deadlatch F06 & F07 panic bolt assembly with or without europrofile pierced backplate 3 pair A1/SS or A4/SS hinges (for door in excess of 910x2100 use 4 pairs) 1 pair C7 overhead door closers K4 or K5 kick plates note - wall finishes and architraves omitted for clarity Furniture - refer to Approved Ironmongery for the Railway Environment for specific door requirements Signs - follow the heirarchy laid down in the LUL Signs Manual section 6.8 Page 65