IRONWORKERS MSIW50S MSIW66S MSIW60D MSIW71D MSIW93D
|
|
- Brittney Parrish
- 6 years ago
- Views:
Transcription
1 IRONWORKERS MSIW50S MSIW66S MSIW60D MSIW71D MSIW93D MSIW126D MSIW126DX MSIW192DX MSIW126D R SINGLE AND DUAL CYLINDER MACHINES TON CAPACITY 5 STATIONS HEAVY DUTY CONSTRUCTION COMPLETELY INTEGRATED EXPECT QUALITY, DEMAND PERFORMANCE Visit us at:
2 IRONWORKERS
3 STANDARD WORK STATIONS 1. PUNCHING STATION The double acting punch cylinder is machined and faced to assure proper alignment of the cylinder shaft under maximum load. Cylinder stroke length is adjustable both top and bottom with two easily set limit switches. The see-through stripper provides full view of punch for ease of alignment and operation. The stripper is also adjustable for varying thickness of material. 1. PUNCH DIE HOLDER The die holder will accept standard tooling and has two hole sizes (D and DX series only). The die holder slides in and out on two T-slots for ease of alignment and makes tooling changeover quick and trouble-free. The overhanging feature of the die holder allows for punching channel flange. 1. PUNCH TABLE The punch table provides support for the workpiece and also incorporates a worktable scale and an adjustable back stop for gauging. The punch work table is segmented and the front portion can be removed for punching angle iron. 2. BAR SHEARING STATION The round and square bar station allow for shearing various sizes using the holddown device. Larger and smaller blades are available. 3. ANGLE SHEAR The angle shear allows for both straight and miter cuts of varying sizes of angle material without a drop-out slug. The two alignment guides assure the squareness of every cut, while the adjustable holddown keeps distortion to a minimum. The angle shear blades have four useable sides and are easily changed. 4. FLAT BAR SHEAR The flat bar shear station has a cast iron support table with guides for accurate positioning and has scribe marks at 30 and 45 degrees for miter cuts. With the adjustable holddown and an upper blade with only a 3 degree rake angle, deformation is held to a minimum. The lower blade has four useable sides. A special feature of the flat bar shear is variable degree miter cutting on angle flange. 5. NOTCHING STATION The notcher is ideal for notching on either flat bars or angles. The gauging table has adjustable stops for precise positioning and the safety guard is electrically interlocked for maximum safety and visibility.
4 STANDARD WORK STATIONS Punching Station, Round Shearing Station, Square Section Shearing Station, Angle Shearing Station, Flat Bar Shearing Station, U-Notching Station, Angle Section (45 Degree) Shearing, Central Lubrication Pump, Electrical Back Gauge (Standard in Double Pistons), Work Light. PUNCHING The machine punches from *1-1/5 (30 mm) diameter s (1/3 or 8 mm thickness) to *2-1/4 (57 mm) diameters (6/7 or 22 mm thickness) very efficiently. Punches and dies are easily changed. STEEL BAR SHEARING With this part of machine, squares from *1 (25 mm) to *2-1/6 (55 mm) and rounds from *1-1/5 (30 mm) diameters to *2-4/7 (65 mm) diameters can be cut very fast. By changing the blades you can also cut U or T sections. ANGLE SHEAR Here you can cut several types of angle sections efficiently. PLATE SHEAR With the long blade, you can do your daily sheet metal cutting works very fast. NOTCHING The machine comes with a rectangular notching tool which you can use for your notching works. We provide special notching tools for your notching works. *Punching diameter, material diameter and thickness can change according to machine models. MSIW66S MSIW93D MSIW126D *Some safety equipment may have been removed or opened to illustrate products clearly and must be in place, and functioning, prior to operation.
5 OPTIONAL ACCESSORIES IPN/UPN Shearing Blade, Hydraulic Stripper, IPN/UPN and Angle Punching Tool, 90 V Angle Shearing Tool, Flat Bar Radius Tool, GDDA Punch Size 6-38mm, GDDA Punch Size 39-57mm, GDDA Punch Size 58-85mm, Press Brake Tool, IPN Punching Tool, Work Light, Louvre Punching Tool, Several Kinds of Punches and Dies. LARGE HOLE AND SECTION PUNCHING, PRESS BRAKE TOOL The machine optionally punches from *1-1/2 (38 mm) diameters (*1/3 or 8 mm thickness) to *5 (125 mm) diameters (1/5 or 5 mm thickness) very efficiently. Punches and dies are easily changed. You can punch I, U, bar bending and angle sections in desired shape and size. Punches and dies are easily changed. Optional, by adding press brake on punching station you can do your daily sheet bending works very easily. We provide necessary tools. SECTION BLADES In this part of the machine you can cut U, I and T channel by changing blades. We provide special blades. SPECIAL V-NOTCHING TOOL Optional, by adding special V-notching tool to rectangular notching tool station you can notch 90 V notches very efficiently. We provide tools for special notching works. *Punching diameter, material diameter and thickness can change according to machine models. MULTI VEE PRESS BRAKE LARGE HOLE PUNCH VEE NOTCHER (PUNCH END) LOUVRE PUNCH CHANNEL AND ANGLE PUNCH CHANNEL SHEAR
6 3501 Marvel Drive Oshkosh, WI USA Phone: Fax: Visit us at:
IW SERIES IRONWORKERS DURMA
IW SERIES IRONWORKERS BETTER PARTS BETTER PROFITS IW SERIES IRONWORKERS STANDARD EQUIPMENT Swing Away Stripper Punching Station Section Cutting Angle Cutting Flat Bar Shearing Notching Twist and Drop Punch
More informationSMF & MACHINE TOOLS, INC
SMF & MACHINE TOOLS, INC 800-643-5839 METAL WORKING EQUIPMENT Local 501-897-1110 Fax 501-897-1110 14824 Rockbridge Road Little Rock, AR 72206 www.smfmachinetools.com sales@smfmachinetools.com C. '..-...p
More informationPII140 IRONWORKER PII140
14824 Rockbridge Road Little Rock, AR 72206 Toll Free 800-643-5839 Fax 501-897-4090 www.smfmachinetools.com sales@smfmachinetools.com IRONWORKER 6 1 5 4 2 STANDARD FEATURES 1. Mechanical Stripper Attachment
More informationSMF & MACHINE TOOLS, INC
SMF & MACHINE TOOLS, INC 800-643-5839 METAL WORKING EQUIPMENT Local 501-897-1110 Fax 501-897-1110 14824 Rockbridge Road Little Rock, AR 72206 www.smfmachinetools.com sales@smfmachinetools.com P II 0 IRONWORKER
More information14824 Rockbridge Road Little Rock, AR Toll Free Fax
14824 Rockbridge Road Little Rock, AR 72206 Toll Free 800-643-5839 Fax 501-897-4090 www.smfmachinetools.com sales@smfmachinetools.com IRONWORKER STANDARD FEATURES 1. Urethane Stripper Attachment keeps
More informationfor impressive performances HYDRAULIC STEELWORKER Compact 50, 65, 80
for impressive performances HYDRAULIC STEELWORKER Compact 50, 65, 80 HYDRAULIC STEELWORKERS COMPACT 50, 65, 80 The Compact 50, 65 and 80 are universal and compact hydraulic steelworkers. They are equipped
More informationYale Environmental Health & Safety 135 College Street, Suite ehs.yale.edu Page 2
Yale Environmental Health & Safety Equipment/Task Name: Equipment/Task Hazard Class: Shop Name: IRONWORKERS 4 http://ehs.yale.edu/forms-tools/toolclassification-matrix Shop Hazard Class: Purpose An ironworker
More informationNUMBER 1 Di-Acro Hand Notcher
OPERATOR S MANUAL & INSTRUCTIONS NUMBER Di-Acro Hand Notcher Di-Acro, Incorporated PO Box 9700 Canton, Ohio 7 373 Progress Street N.E. Canton, Ohio 705 330-55-9 330-55-00 (fax) Revised 0/0 Sale or distribution
More informationSCOTCHMAN INDUSTRIES MODEL FI M IRON WORKER
SCOTCHMAN INDUSTRIES MODEL FI-8510-20M IRON WORKER NOVEMBER 2012 TABLE OF CONTENTS SECTION DESCRIPTION PAGE # 1.0 INTRODUCTION 5 2.0 SAFETY PRECAUTIONS 6 2.1 WARRANTY 7 3.0 WARNING LABELS 8-9 4.0 INSTALLATION
More informationTu r n y o u r p r e s s b r a k e o r p u n c h p r e s s i n t o a h o l e p u n c h i n g p r o f i t c e n t e r.
Tu r n y o u r p r e s s b r a k e o r p u n c h p r e s s i n t o a h o l e p u n c h i n g p r o f i t c e n t e r. U n i P u n c h M o d u l a r To o l i n g Works with existing presses Multiple holes
More informationENGLISH (mm) BENDICROP SERIES
ENGLISH (mm) BENDICROP SERIES BENDICROP SERIES Metalwork companies need to perform simple bending work. GEKA has designed the BENDICROP MODELS which, apart from including L, B, A, I, cutting stations,
More informationProductive CNC punching with affordable configurations for all fabrication shops. Available Options:
Machine Specifications Working Range CP 750............................... 30" 80" CP 1000.............................. 40" 80" CP 1250.............................. 50" 80" Maimum sheet length.................................
More informationStrongman Metal Tools Price list February 2018
Strongman Metal Tools CC CK 2004/095733/23 CALL ANDRIES FOR EXPERT ADVICE 083 327 9988 or 087 135 2229 Soli Deo Gloria info@strongman.co.za Strongman Metal Tools Price list February 2018 PLEASE NOTE PRICES
More informationSCOTCHMAN INDUSTRIES MODEL DO M IRONWORKER
SCOTCHMAN INDUSTRIES MODEL DO-8514-20M IRONWORKER JULY 2012 TABLE OF CONTENTS SECTION DESCRIPTION PAGE # 1.0 INTRODUCTION 5 2.0 SAFETY PRECAUTIONS 6 2.1 WARRANTY 7 3.0 WARNING LABELS 8 4.0 INSTALLATION
More informationSOLUTION BULLETIN KNOCKOUTS 101 DEFINITION
KNOCKOUTS 101 DEFINITION A knockout is a feature in sheet metal created by punching a slug free of but attached to the sheet with small un-cut areas called tabs. A knockout allows for variation in a part
More informationTrade of Metal Fabrication. Module 1: Basic Fabrication Unit 6: Universal Ironworker Phase 2
Trade of Metal Fabrication Module 1: Basic Fabrication Unit 6: Universal Ironworker Phase 2 Table of Contents List of Figures... 5 List of Tables... 5 Document Release History... 6 Module 1 Basic Fabrication...
More informationdesign and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses
design and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses UPH 28 Horizontal hydraulic press - Built-in memory makes it possible to save up to 4 bending
More informationMetal Working Processes
Metal Working Processes Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 CLASSIFICATION OF MANUFACTURING PROCESSES TOPIC OUTLINE What is Sheet Metal? Sheet Metalworking
More informationMODEL 5014TM IRONWORKER
MODEL 5014TM IRONWORKER PRINTED JUNE 2014 TABLE OF CONTENTS SECTION DESCRIPTION PAGE # 1.0 INTRODUCTION 4 2.0 SAFETY PRECAUTIONS 4 2.1 WARRANTY 5 3.0 WARNING LABELS 6 4.0 INSTALLATION & SET UP 8 4.1 Physical
More informationMODEL 50514CM IRONWORKER
MODEL 50514CM IRONWORKER PRINTED FEBRUARY 2015 TABLE OF CONTENTS SECTION DESCRIPTION PAGE # 1.0 INTRODUCTION 4 2.0 SAFETY PRECAUTIONS 5 2.1 WARRANTY 7 3.0 WARNING LABELS 8 4.0 INSTALLATION & SET UP 10-21
More informationANGLE AND FLAT BAR LINE ABL-74T
ANGLE AND FLAT BAR LINE ABL-74T ABL-74T The ABL-74T is our most economical, entry level machine for punching and shearing angle and flat bar. It has a combination of features requested by our customers.
More informationMaintenance Manual Original Instructions - IW6004
Maintenance Manual Original Instructions - IW6004 Maintenance Manual 1 General Operator and Supervisor Information Signal Word Definition Signal Word Panel 2 Maintenance Precautions Maintenance Schedule
More informationOPERATOR S MANUAL MODEL 207 WORK SAFELY AT ALL TIMES WITH QUALIFIED OPERATORS ONLY. QUALIFIED OPERATORS NAME SHIFT DA TE
OPERATOR S MANUAL WORK SAFELY AT ALL TIMES WITH QUALIFIED OPERATORS ONLY. MODEL SERIAL# We, the undersigned, have read and understand the OPERATOR S MANUAL. QUALIFIED OPERATORS NAME SHIFT DA TE Safety
More informationMetal Stamping Glossary
Metal Stamping Glossary Alloy - A substance that has metallic properties and is composed of two or more chemical elements of which at least one is an elemental metal. Annealing - A process involving the
More informationItem #28187 EASTWOOD BEAD ROLLER INSTRUCTIONS
Item #28187 EASTWOOD BEAD ROLLER INSTRUCTIONS The Eastwood Bead Roller is a professional metal fabrication tool for producing strengthening ribs in panels used in creating replacement fl oor pans, fi rewalls,
More informationMETALMASTER HG-3216VR. Hydraulic NC Guillotine - Variable Rake x 16mm Mild Steel Shearing Capacity. Product Brochure
Product Brochure S9615 METALMASTER HG-3216VR Hydraulic NC Guillotine - Variable Rake 3200 x 16mm Mild Steel Shearing Capacity Page 1 of 5 Right View Front View Side View Rear Guarding 3 Safety Electronic
More informationOperating Manual. for CUTTING, PERFORATING, BENDING SLB120
Operating Manual for CUTTING, PERFORATING, BENDING SLB120 31040\B06eng 0896 0 Contents 1. Scope of delivery... 1 2. Technical specifications... 1 3. Applications... 1 4. Commissioning... 2 5. Cutting...
More informationTENSILKUT ENGINEERING
TENSILKUT ENGINEERING For Accurate Test Specimens Manufacturer of equipment for the accurate preparation of physical test specimens since 1955 SIEBURG INTERNATIONAL, INC. 1901 Clydesdale Street, Maryville,
More informationUnitized Press Brake Tooling
733396C Unitized Press Brake Tooling For use with the Tog-L-Loc Sheet Metal Clinching System BTM s unitized press brake tooling is a cost-effective method to utilize the Tog-L-Loc sheet metal joining system.
More informationALFRA PRESS. Made in Germany by ALFRA
52 ALFRA PRESS Made in Germany by ALFRA 53 ALFRA PRESS Overview ALFRA PRESS AP 250 ALFRA PRESS AP 400 Page 56 Page 58 Control cabinet housing, control cabinet doors, mounting plates Control cabinet housing,
More informationPress Operations & Types of Dies
Press Operations & Types of Dies Press Working Use of mechanical and hydraulic presses for forging and extrusion has been mentioned earlier. Knuckle type mechanical presses are used widely for sheet metal
More informationAssembly, Installation, Maintenance and Operation Instructions For
Assembly, Installation, Maintenance and Operation Instructions For Spacefile LT Storage System January 2010 SPACEFILE INTERNATIONAL CORP. 1145 FEWSTER DRIVE, MISSISSAUGA, ON, CANADA L4W 1A2 TOLL FREE 1
More informationDanly Die Sets CATALOG DIE SETS. Quality & performance Quick delivery Precision Components
Danly Sets TM CATALOG DIE SETS Quality & performance Quick delivery Precision Components 1 TM Danly Sets www.anchordanly.com CATALOG DIE SETS Service We Deliver and Quality You Can Depend On Danly Sets
More information$42, $46, Product Brochure For S961. Features
HG-3212VR - 3200 x 12mm Mild Steel Shearing Capacity 1-Axis Ezy-Set NC-89 Go-To Control & Hardened Ballscrew Backgauge ORDER CODE: MODEL: Ex GST Inc GST $42,500.00 $46,750.00 S961 HG-3212VR Shearing Capacity
More informationModel: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5
SHEARER/PRESS BRAKE/ SLIP ROLL Model: 3-IN-1/1067x1.5 Model: 3-IN-1/1320x1.5 OPERATION MANUAL 1. USES This machine is used for shearing and bending low carbon plate (mild steel) or the other metal materials
More informationOperations Manual. Serial Number: Original Instructions - IW7503
Operations Manual Serial Number: Original Instructions - IW7503 Operations Manual 1 General Declarations of Conformity Company Profile Warranty Machine Identification Operator and Supervisor Information
More informationPRESS & PRESS WORK
Topic and Contents Hours Marks 2.1 Introduction 08 Marks Materials used in press work for automobile applications. Classifications of presses and terminology used in presses Major parts of Fly press 2.2
More informationSeries 8 Mark II. Universal Vertical Band Saw
Series 8 Mark II Universal Vertical Band Saw Capacity 18 x 22 Marvel Series 8 Mark II Universal Tilt-Frame Vertical Band Saw The Marvel Series 8 Mark II has a capacity of 18 x 22 (18 diameter round) with
More informationASSIGNMENT 4. Textbook Assignment: The point, edge, face, heel, and tang are the five parts of which of the following tools?
ASSIGNMENT 4 Textbook Assignment: "Files," "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and
More informationSection 10s PRESS BRAKE TOOLING. Product of USA SOURCE CATALOG FOR AMERICAN STYLE
www.ceooling.com Section 0s PRESS BRAKE OOLING SOURCE CAALOG FOR AMERICAN SYLE Product of USA 90 Forming Punches and Dies 90 Forming Punches and Dies hese punches and dies are the most widely used to form
More informationENGINEERING STANDARDS SECTION: D TOG-L-LOC V-LOC OVAL-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
More informationProfiform 200 Profiform 320. Operating manual
Profiform 200 Profiform 320 Operating manual Profiform 200 / Profiform 320 Operating manual Page 1 Table of contents 1. General information Page 2 2. Profile of the Profiform sheet metal working machines
More informationDi-Acro 36 Power Shear
OPERATOR S MANUAL & INSTRUCTIONS Di-Acro 36 Power Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02 Sale
More informationMANUFACTURING TECHNOLOGY
MANUFACTURING TECHNOLOGY UNIT II SHEET METAL FORMING PROCESSES Sheet Metal Introduction Sheet metal is a metal formed into thin and flat pieces. It is one of the fundamental forms used in metalworking,
More informationSwing beam hydraulic shear. Heavy-duty, all-welded-steel rigid frame. Hold-down pressure adjustment depending on cutting pressure
Swing beam hydraulic shear Heavy-duty, all-welded-steel rigid frame Hold-down pressure adjustment depending on cutting pressure Colour Touch Screen 10,4 Programmed cutting length Close hold-downs near
More informationA M Supply Co. Metalworking Machinery. Drill Presses Jet Tools J-2221VS 20" Variable Speed Drill Press 115/230V 1Ph
Drill Presses J-2221VS 20" Variable Speed Drill Press 115/230V 1Ph Part # Style Drills to Center Drilling Cap. Cast Drilling Cap. Mild Distance Column Circle Iron Steel to Spindle 354221 Variable 20" 1-1/4"
More informationLockformer / 16 Gauge Speednotch
Lockformer / 16 Gauge Speednotch INSTALLATION PRELIMINARY: After uncrating, locate unit, with or without base skid, to area of operation. Unbind foot switch cord and cylinder hoses and remove gauge pin
More informationSPECIFICATIONS MS-10-5 MS Cutting capacity (Rated 80,000 PSI Tensile) Cutting length 62 in "
MS-25-10 STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere in the stroke the ram returns to "up" position. Two
More informationCOMPANY HISTORY CONTENTS. Di-Acro Metal Fabricating Equipment
COMPANY HISTORY Di-Acro Metal Fabricating Equipment Metal fabrication equipment has been our specialty for more than 60 years! We are proud to continue the traditional craftsmanship and quality that our
More informationHINGE TOOL SET-UP, ADJUSTMENT AND TROUBLESHOOTING GUIDE
HINGE TOOL SET-UP, ADJUSTMENT AND TROUBLESHOOTING GUIDE HINGE TOOL FORMING SET-UP High Level Process (For detailed information, reference Detailed Instructions): 1. Inspect and assemble tool (if required).
More informationSheet-Forming Processes
Sheet-Forming Processes Chapter 17 17.1 Introduction Sheet metal processes involve plane stress loadings and lower forces than bulk forming Almost all sheet metal forming is considered to be secondary
More informationCNC SYSTEMS PUNCHING SHEARING MARKING. Trilogy Machinery, Inc.
The CNC Systems from SUNRISE are plate, angle and channel positioning systems with user-friendly interfaces. Many options are available factory-installed on Dual-Cylinder Ironworker or Punching Machines
More informationProviding Tools To Form Your Success
If it's important to you, it's important to us. Find out how our attention to details forms the basis for your success. Providing ools o able of Contents For more than 30 years, leading sheet metal fabricators
More informationSheet Metal Tools. by:prem Mahendranathan
Sheet Metal Tools by: SHEET METAL TOOL KIT SHEET METAL TOOLS Rivet Gun 3/32, 1/8, 5/32, 3/16",Cupped Set Mini Bucking Bar Footed Heel-Toe Bucking Bar Air Tool Oil Mechanics Tool Bag High-Speed Air Drill
More informationDesign and Analysis of Progressive Die for Chain Link Plate
Design and Analysis of Progressive Die for Chain Link Plate Md Inaithul Rehaman #1, P Satish Reddy #2, Matta Manoj #3, N.Guru Murthy #4 ME Department, Prasiddha College of Engg and Technology, Anathavaram
More informationMS HYDRAULIC GUILLOTINE SHEAR
MS-25-10 HYDRAULIC GUILLOTE SHEAR MS-25-10 HYDRAULIC GUILLOTE SHEAR STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere
More informationHow to use. Use example. Non-scratch sheet prevents die marks. Tight-knit super fiber provides a working life of many hundreds cycles.
How to use Small to Medium dies Fix Kizu-non on the die shoulder with masking tape. Should not be crinkled. *Cut Kizu-non with scissors for desired length. Large dies Fix Kizu-non on each die shoulders.
More informationClinch Tooling. Standard Punches, Dies, Strippers, & Holders for clinching sheet metal
733440BC Clinch Tooling Standard Punches, Dies, Strippers, & Holders for clinching sheet metal Strong mechanical joints without external fasteners or welding Commonly used to join harder materials & multiple
More informationDesign and Analysis of Press Tool Assembly
Design and Analysis of Press Tool Assembly Raveendra M.Tech Student ABSTRACT Press working may be defined as a chip less manufacturing process by which various components are made from sheet metal. This
More informationManufacturing Processes (1)
Manufacturing Processes (1) Chapter Twenty: Sheet Metalworking Dr. Eng. Yazan Al-Zain Department of Industrial Engineering 1 Introduction Sheet Metalworking includes cutting and forming operations performed
More informationHydraulic NC Guillotine & NC Panbrake Package Deal
Product Brochure K059 METALMASTER HG-2504 & PB-830T Hydraulic NC Guillotine & NC Panbrake Package Deal Ezy-Set NC-89 Guillotine - 2500 x 4mm, NC Ezy Touch Screen Panbrake 2500 x 4mm Page 1 of 6 Specifications
More informationTURN METAL INTO MONEY With our range of HAND POWERED METAL WORKING MACHINES THINK OF THE POSSIBILITIES IF YOU COULD MAKE THESE:
TURN METAL INTO MONEY With our range of HAND POWERED METAL WORKING MACHINES THINK OF THE POSSIBILITIES IF YOU COULD MAKE THESE: MULTI BEND SYSTEMS *Bend: *Bend: Mild Mild Steel, Steel, Stainless Stainless
More informationHolemaking Products & Accessories
Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy and consistency to get
More informationENGINEERING STANDARDS SECTION: TOG-L-LOC V-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
More informationALUMA-CLASSIC FENCE W1716 & W1720 INSTRUCTION MANUAL
ALUMA-CLASSIC FENCE W1716 & W1720 INSTRUCTION MANUAL Phone: Phone: 1-360-734-3482 On-Line On-Line Technical Technical Support: Support: tech-support@woodstockint.com tech-support@shopfox.biz COPYRIGHT
More informationModel Assembly & Operating Instructions
30 SHEAR BRAKE ROLL Model 05907 Assembly & Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationWire and tube Drawing
Wire and tube Drawing Drawing is an operation in which the cross-section of solid rod, wire or tubing is reduced or changed in shape by pulling it through a die. The principle of this procedure consist
More informationOperating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher
Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand
More information4. PRESS AND PRESS WORK
4. PRESS AND PRESS WORK Q. Which are the materials used for press work? GALVANISED IRON Zinc-coated iron is known as "galvanised iron"'. This soft steel sheet is popularly known as Gl sheet. Applications:
More informationPRODUCTION VISES. Vises. Bock Quick Change Fixturing. 5-Axis Production Vises
Vises Introduction to Design... 74 75 VMC/HMC Solutions...76 77 Ball Lock Mounting System...78 79 Production Vises 4" (100 mm) Production Vises... 80 81 6" (150 mm) Production Vises...82 83 Self Centering
More informationSANDVIK 20C STRIP STEEL
SANDVIK 20C STRIP STEEL DATASHEET Sandvik 20C is a hardened and tempered carbon steel characterized by good properties in respect of: Fatigue strength and wear resistance Hardness combined with ductility
More informationSave Set-up Time... and More!
System Bock Save Set-up Time... and More! Bock Locator Plates The foundation for quick change workholding efficiency. The Bock Locator Plate is a hard coated aluminium subplate with precision bored and
More informationTOOL DESIGN - MANUFACTURING DESIGN SPECIFICATIONS FOR TOOLING AND EQUIPMENT SECTION H - DIE DESIGN TABLE OF CONTENTS. H.1 General...
TABLE OF CONTENTS H.1 General...Page 2 H.2 General Die Layout...Page 2 H.3 General Die Features...Page 2 H.4 Specific Die Type Features...Page 5 H.5 Special Punches and Die Bushings...Page 6 H.6 Wire E.D.M...Page
More informationINTRODUCTION TO PRESS BRAKES. A Vital Piece of Shop Equipment
INTRODUCTION TO PRESS BRAKES A Vital Piece of Shop Equipment Introduction to Press Brakes Press Brakes are utilized in the forming lengths of sheet metal components. A press brake is a vital necessity
More informationMETAL SHEAR SPECIALISTS MS-25-5 HYDRAULIC GUILLOTINE SHEAR
MS-25-5 HYDRAULIC GUILLOTE SHEAR MS-25-5 HYDRAULIC GUILLOTE SHEAR STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere
More informationIWB-40 - Industrial Work Bench
IWB-40 - Industrial Work Bench 1800 x 750 x 900mm 1000kg Load Capacity On Sale Ex GST Inc GST $398.00 $343.48 $457.70 $395.00 ORDER CODE: A420 MODEL: Type: IWB-40 Steel with Laminated Top Table Top Load
More informationModule 3 Selection of Manufacturing Processes
Module 3 Selection of Manufacturing Processes Lecture 4 Design for Sheet Metal Forming Processes Instructional objectives By the end of this lecture, the student will learn the principles of several sheet
More informationMODEL 36 Di-Acro Hand Shear
OPERATOR S MANUAL & INSTRUCTIONS MODEL 36 Di-Acro Hand Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02
More informationClamping devices 521
Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps
More informationIWB-12P2 - Industrial Work Bench Package Deal 1200 x 750 x 1725mm 1000kg Load Capacity
IWB-12P2 - Industrial Work Bench Package Deal 1200 x 750 x 1725mm 1000kg Load Capacity On Sale Ex GST Inc GST $599.13 $565.22 $689.00 $650.00 Package Contents - SAVE $148.10 (Inc) 1x 1x 4x 4x 1x 1x 1x
More informationSTC Hydraulic grinding milling machine for cylinder heads and blocks. BERCO S.p.A. A Company of ThyssenKrupp
STC 361-1300 Hydraulic grinding milling machine for cylinder heads and blocks A Company of ThyssenKrupp BERCO S.p.A. The machine and its executions - from grinding wheel to tool: 1 - from tool to milling
More informationSL Let it Rain. Solutions for fast, precise cuts in thin walled K-Style & half round gutter.
SL15114 Let it Rain Solutions for fast, precise cuts in thin walled K-Style & half round gutter. Quick-Action Gutter Outlet Saws & Combination Arbor & High Speed Pilot Drill For downspout that always fits
More informationMANUFACTURING PROCESSES
1 MANUFACTURING PROCESSES - AMEM 201 Lecture 9: Sheet Metal Cutting & Forming Processes DR. SOTIRIS L. OMIROU Sheet Metal Cutting & Forming Processes - Application field- Sheet metal processing is an important
More informationTOOLS/ werkzeugtechnik
TOOLS werkzeugtechnik EDITORIAL In October 2006, ips-werkzeugtechnik took over the punching technology segment of DE-STA-CO Europe & Co. Werkzeugtechnik, which has earned us a new strategic position on
More informationDi-Acro 18E Stylus Turret Punch Press
OPERATOR S MANUAL & INSTRUCTIONS Di-Acro E Stylus Turret Punch Press Di-Acro, Incorporated PO Box 00 Canton, Ohio Progress Street N.E. Canton, Ohio 0 0-- 0--00 (fax) Revised 0/0 Sale or distribution of
More informationProFormer Professional Tubing Bender. Part #12485
ProFormer Professional Tubing Bender Part #12485 Eastwood s ProFormer Professional Tubing Bender is designed around a rigid welded steel frame, iron/aluminum die and roller along with a 8 ton jack that
More informationThe Fine-Art of Sheet Metal Bending
The Fine-Art of Sheet Metal Bending Introduction...... 1 Bend allowances........2 Reverse engineering the k-factor........ 4 Principle types of bending........ 5 Tips and tricks....... 7 Other common types
More information# in 1 Metal Worker Auxiliary Operating Instructions
340 Snyder Avenue, Berkeley Heights, NJ 07922 www.micromark.com MMTechService@micromark.com Tech Support: 908-464-1094, weekdays, 1pm to 5 pm ET #86556 3 in 1 Metal Worker Auxiliary Operating Instructions
More informationDesign Guide: Sheet Metal Fabrication VERSION 2.1
Design Guide: Sheet Metal Fabrication VERSION 2.1 SHEET METAL GUIDE V2.1 Table of Contents Overview...3 Tolerances...4 General Tolerances...4 Wall Thickness...5 Bends...5 Curls...6 Countersinks...6 Hems...7
More informationIKEGAI MACHINE TOOLS FOR CUSTOMIZED USE
THE ART OF TECHNOLOGY IKEGAI MACHINE TOOLS FOR CUSTOMIZED USE 1 CONTENTS Please click slide title. CM0J110616HP 2 USER + IKEGAI = SPECIALIZED MACHINES IKEGAI as specialized machine player in the manufacturing
More informationHAND SHEARS NO. 12 AND NO. 24
OPERATOR S MANUAL & INSTRUCTIONS HAND SHEARS NO. AND NO. Di-Acro, Incorporated PO Box 9700 Canton, Ohio 7 7 Progress Street N.E. Canton, Ohio 70 0--9 0--00 (fax) Revised 0/0 Sale or distribution of manuals
More informationOWNER S MANUAL. Safety. Please read this owner s manual before use and keep it at hand for reference. Warranty
Please read this owner s manual before use and keep it at hand for reference. OWNER S MANUAL Safety Important safety instructions for using the INCRA Miter5000 Before using the INCRA Miter5000, read and
More informationG-SERIES MECHANICAL SHEARS
/0-1' ;)._ D~ n~~~trn Pl-321 G-SERIES MECHANICAL SHEARS?i-V/ Now, with the CINCINNATI "G"-Series, you can have CINCINNATI quality, reliability, prod uctivity and versatility in a mechanical shear which
More informationHYDRAULIC IRONWORKER MHM 70. Operation Manual
HYDRAULIC IRONWORKER MHM 70 Operation Manual MIHO HYDRAULIC IRONWORKER This MIHO Ironworker has been developed to give you, the user, a reliable long service- low maintenance machine tool. These machines
More informationCorso di Studi di Fabbricazione
Corso di Studi di Fabbricazione 3a Richiami dei processi tecnologici di trasformazione FUNDAMENTAL OF METAL FORMING 1 METAL FORMING Large group of manufacturing processes in which plastic deformation is
More informationALFRA hole punches application overview
ALFRA hole punches application overview ALFRA HOLE PUNCHES MonoCut ALFRA HOLE PUNCHES TriCut ALFRA HOLE PUNCHES TriCut+ ALFRA HOLE PUNCHES TwinCut Suitable for Sheet steel S5 F 70 N/² Stainless steel F
More informationAMETAL SHAPER is indispensable for certain METAL SHAPER FOR YOUR SHOP. By S. S. Miner
METAL SHAPER FOR YOUR SHOP By S. S. Miner AMETAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationPrecision Grinding and Control Vise. Vises PSS. Tools and Accessories. For more Information current prices, please
PSK 50 shown incl. pull-down feature Vises Precision Grinding and Control Vise high precision, robust structure, hardened and ground v-grooves, high holding capacity can be used on 4 different sides face
More informationMobile Weapons Storage System Specifications
Mobile Weapons Storage System Specifications Whatever your weapon storage needs, Hi-Density s customized Weapons Storage System will be designed to fit your unique specifications. We recognize that security
More informationTrade of Sheet Metalwork. Module 1: Sheetmetal Fundamentals Unit 14: Exhaust Pipe Phase 2
Trade of Sheet Metalwork Module 1: Sheetmetal Fundamentals Unit 14: Exhaust Pipe Phase 2 Table of Contents List of Figures... 4 List of Tables... 4 Document Release History... 5 Module 1 Sheetmetal Fundamentals...
More information