DX-Kwik X-M6H, X-M8H Threaded Studs and DNH, X-DKH Nails
|
|
- Ruth Morris
- 5 years ago
- Views:
Transcription
1 X-M6H, X-M8H Threaded Studs and DNH, X-DKH Nails Produt data Dimensions General information X-M6H- -37 FP8 Material speifiations M6 o 3.7 Carbon steel shank: HRC 58 g 37 Zin oating: 5 20 μm Reommended fastening tools X-M8H -37 P8 o 5.5 M8 o 4.5 DX 460, DX 5, DX 36, DXE-72 See fastener program in the next pages and Tools and equipment hapter for more details. 3.5 g DNH 37 P8S15 2 o s X-DKH 48 P8S15 2 o 4 s o 15 Approvals IBMB 3041/8171 X-M8H, X-DKH, X-M6H DIBt (Germany): X-M8H Note: Tehnial data presented in these approvals and design guidelines reflet speifi loal onditions and may differ from those published in this handbook. o 15 2 s Appliations Examples Base plates, rails for piping Radiator brakets Floor stands, metal fixtures to onrete Suspended eilings 12/
2 oad data Reommended loads N re,1 [kn] N re,2 [kn] V re,1 [kn] M re,1 [Nm] X-M6H, DNH X-M8H, X-DKH Conditions N re,1 : onrete in ompressive zone. N re,2 : onrete in tension zone. Predominantly stati loading. Conrete C20/25 C50/60. A suffiient redundany has to be ensured, that the failure of a single fastening will not lead to ollapse of the entire system. Reommended loads are based on failure of the fastener anhorage in the onrete. Thikness and quality of the fastened material may lower the loadings. Observane of all pre-drilling requirements, fastened thikness limits, and reommended details. The reommended loads in the table refer to the resistane of the individual fastening and may not be the same as the loads F N and F V ating on the fastened part. Note: If relevant, prying fores need to be onsidered in design, see example. Moment ating on fastener shank only in ase of a gap between base and fastened material. Arrangements to prevent moment on shank: Coupler tight against onrete Z F V F N Non-symmetri arrangement Z2 Z3 F N Z1 F V Moment on fastened part Prying effet must be onsidered in determining loads ating on fastener Resultant fores on nail /2017
3 Appliation requirements Thikness of base material X-M6H, DNH 37: X-M8H, X-DKH 48: h min = 100 mm h min = 100 mm Thikness of fastened material X-M6H: X-M8H: DNH 37: X-DKH 48: t l g - t washer - t nut up to 13.5 mm t l g - t washer - t nut up to 14.0 mm t l 2.0 mm t l 5.0 mm or t l 2.0 by pre-drilling through fastened material Spaing and edge distanes (mm) Pairs Row along edge General (e.g. group of fasteners a a Reinfored Non-reinfored Reinfored Non-reinfored Reinfored Non-reinfored a Corrosion information The intended use only omprises fastenings whih are not diretly exposed to external weather onditions or moist atmospheres. For further detailed information on orrosion see relevant hapter in Diret Fastening Priniples and Tehnique setion. 12/
4 Fastener program Fastened Fastener thikness t I,max [mm] Designation Item no. g [mm] s [mm] [mm] X-M6H FP X-M8H P X-M8H/ P X-M8H/ P DNH 37 P8S * X-DKH 48 P8S *) with pre-drilling through fastened material t I,max = 2.0 mm Tools, artridge seletion and tool energy setting DX 460, DX 5, DX 36, DXE-72: 6.8/11M yellow or red artridge Tool energy adjustment by setting tests on site. Fastening quality assurane Fastening inspetion X-M6H, X-M8H DNH 37, X-DKH 48 hnvs Plae nails so that heads and washers bear tightly against eah other and against the fastened material t I h NVS h NVS = - h ET, h ET = mm h NVS 4 mm /2017
5 Installation X-M6H, X-M8H DNH 37, X-DKH 48 o 5 23 Tre ti Pre-drilling details (not through fastened material) DNH 37 t I [mm] Drill-bit Item no. 2 TX-C-5/ o 5 Pre-drill with drill bit Designation Item no TX-C-5/23B or TX-C-5/ Tightening torque Designation T re [Nm] X-M6H 6.5 X-M8H 10.0 X-DKH 48 t I [mm] Drill-bit Item no. 5 TX-C-5/23B or TX-C-5/ o 5 Details valid for C20/25 C50/60 Pre-drilling details (through fastened material) t I X-DKH 48 t I [mm] Drill-bit Item no. 2 only TX-C5/ Details valid for C20/25 C50/60 These are abbreviated instrutions whih may vary by appliation. AWAYS review/follow the instrutions aompanying the produt. 12/
6 /2017
X-HS Threaded Hanger and X-CC Loop Hanger Systems
5, Threaded Hanger and oop Hanger Systems Product data Dimensions DKH À U Á U Â M5 7.5 25.5 10 o15 5 41 36 o 15 HITI 24 7 9.5 o 4 S dg 2 D o 4 12 1.5 8.5 4.5 o 4 8.5 DKH 48 P8S15 o8 o4 o15 X-U _ P8 Ø 8
More informationX-P High Performance Nail for Fastening to Concrete and Wood to Steel applications
X-P High Performance Nail for Fastening to Concrete and Wood to Steel applications Product data X-P_ MX Ø 8.2 2.4 X-P_ P8 Ø 8.2 2.4 Ø 4.0 L s L L s L Ø 4.0 Features and Benefits A specially hardened fastener
More informationBX 3 system: fasteners for Mechanical & Electrical and Interior Finishing applications
BX 3 system: fasteners for Mechanical & Electrical and Interior Finishing applications Product data BX 3 battery-actuated fastening tool Nails (For fastening to concrete) X-P 17/20/24 B3 MX X-P 30/36 B3
More informationBX 3 system: fasteners for Mechanical & Electrical and Interior Finishing applications
BX 3 system BX 3 system: fasteners for Mechanical & Electrical and Interior Finishing applications Product data Nails X-C: o 6.5 X-P: o 6.8 (For fastening to concrete) X-P 17/20/24 B3 MX X-P 30/36 B3 P7
More informationBX 3 system: fasteners for Interior Finishing, Mechanical and Electrical and Building Construction applications
Product data BX 3 system BX 3 system: fasteners for Interior Finishing, Mechanical and Electrical and Building Construction applications BX 3 battery-actuated direct fastening tools BX 3-ME BX 3-IF Fasteners
More informationHPD Aerated concrete anchor. Approvals / certificates. Basic loading data (for a single anchor)
HPD Anchor version HPD Benefits - anchor for autoclaved aerated concrete - maximum use of base material capacity - setting without drilling Autoclaved aerated concrete Fire resistance Sprinkler approved
More informationInstallation Data for Access Stairs and Handrails. PD 63 rev C 01/12/14
Installation Data for Aess Stairs and Handrails 01/12/14 Page 1 of 8 ACCESS STAIRS For road, rail and utilities for aess to maintenane works via an embankment. 1. Sope This doument gives basi guidane on
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2013 Hilti North American Product Technical Guide Volume 1 Direct Fastening. For complete details on this product, including data development, product specifications, general
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15.
The following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15. Please refer to the publication in its entirety for complete details on this product
More informationMaterial Specifications Technical Data
3.4.3.1 Product 3.4.3.2 Material Speciications 3.4.3.3 Technical Data 3.4.3.4 Installation Instructions 3.4.3.5 Ordering Information 3.4.3.1 Product Hilti provides a wide range of solutions for the attachment
More informationTrak-It C4. Trak-It C4 High Performance Gas Fastening System PRODUCT INFORMATION
Trak-It C Trak-It C High Performane Gas Fastening System PRODUCT DESCRIPTION The Trak-It C and CEX gas fastening systems were developed for use in high volume prodution appliations. Powerful rugged tools
More informationUsing Hilti powderactuated. to install suspended metal-framed gypsum board ceilings. The application. Selection of fasteners.
Using Hilti powderactuated fasteners to install suspended metal-framed gypsum board ceilings The application Selection of fasteners Technical data Procedures Fastening quality 0 Using powder-actuated fasteners
More informationPRODUCT INFORMATION. Stainless Steel Version N/A N/A
LokBolt AS LokBolt AS Sleeve Anhor PRODUCT DESCRIPTION The LokBolt AS is an all steel preassemble single unit sleeve anhor whih is esigne for use in onrete or masonry base materials. The anhors are available
More informationRF Link Budget Calculator Manual
RF Link Budget Calulator Manual Author Ivo van Ling for www.vanling.net Software Release RF Link Distane Calulator, Version 1.00, Dated 4 January 2010 Manual Version 1.00 Date 19-01-2010 Page: 1(8) Contents
More informationHUS 6 Screw anchor, Redundant fastening
HUS 6 Screw anchor, Anchor version HUS-A 6 Carbon steel Concrete Screw with hex head HUS-H 6 Carbon steel Concrete Screw with hex head HUS-I 6 Carbon steel Concrete Screw with hex head Benefits - Quick
More informationnineteen wood construction and design Timber Construction Timber Construction Timber Construction
APPLIED ARCHITECTURAL STRUCTURES: STRUCTURAL ANALYSIS AND SYSTEMS DR. ANNE NICHOLS FALL 2017 leture nineteen wood onstrution and design Timber Constrution all-wood framing systems studs, beams, floor diaphragms,
More informationActuated Ball Valves. n e p t r o n. Description. Product Features
for two way and three way ontrol of hot water, hilled water systems & low pressure steam Desription The Atuated Ball Valve is omprised of the atuator, the linkage and the valve body. The standard ball
More informationHK I. Anchor size (carbon steel) HK6 HK6L HK8 Resistance F Rk [kn] 2,0 5,0 5,0
HK HK I Anchor version Benefits - well proven - small drill bit diameter - for fixing in cracked concrete, redundant fastening only, e.g. suspended ceilings a ) Redundant fastening only Approvals / certificates
More informationHDA-P HDA-PR HDA-PF Anchor for presetting. HDA-T HDA-TR HDA-TF Anchor for through-fasting. Nuclear ICC. Steel failure
Anchor version Benefits HDA-P HDA-PR HDA-PF Anchor for presetting HDA-T HDA-TR HDA-TF Anchor for through-fasting suitable for non-cracked and cracked concrete C 20/25 to C 50/60 mechanical interlock (undercut)
More informationX-EKB, X-ECH Electrical Cable Fasteners
X-EKB, X-ECH Electrical Cable Fasteners Product data Dimensions Single Fastener X-EKB 8/4-FR X-EKB 16 (FR) X-U 37 PH 1 2 4 o8.15 16.8 10 21.5 34 136/104 16.8 10 25 229 o3.7 37 49 o11.8 X-ECH-S (FR) X-ECH-M
More informationInternal threaded version: HSC-I carbon steel internal version HSC-IR Stainless steel version (A4) Hilti anchor design software
Anchor version Benefits Internal threaded version: HSC-I carbon steel internal version HSC-IR Stainless steel version (A4) the perfect solution for small edge and space distance suitable for thin concrete
More informationThread protection accessories are installed at the MODIX production factory and delivered with couplers.
Installation of MODIX Rebar Coupler Identification of the product The type of MODIX Rebar Coupler can be identified by the marking on the product. Size of the Coupler can be identified also according to
More informationWedge Type Anchors. Trubolt. Wedge Anchor ADVANTAGES
CONCRETE ANCHORING SPECIALISTS Dependable, Heavy-Duty, Inspectable, Wedge Type Expansion Anch 2015 IBC Compliant DESCRIPTION/SUGGESTED SPECIFICATIONS Wedge Type Anchs SPECIFIED FOR ANCHORAGE INTO CONCRETE
More informationNBC - filter GF-20. Initial pressure drop as a function to the air volume in the new filter
Initial pressure drop as a function to the air volume in the new filter 1 500 1 000 900 800 700 600 500 400 300 200 100 90 80 70 60 50 GF-300 GF-150 GF-75 GF-600 General requirements for gasfilters - Gas-tight
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2013 Hilti North American Product Technical Guide Volume 1 Direct Fastening. For complete details on this product, including data development, product specifications, general
More informationX-EKB, X-ECH Electrical Cable Fasteners
X-EKB, X-ECH Electrical Cable Fasteners Product data Dimensions Single Fastener X-EKB 8/4-FR X-EKB 16 (FR) X-U 37 PH 1 2 4 o 8.15 16.8 10 21.5 34 136/104 16.8 10 25 229.7 37 49 o 11.8 X-ECH-S (FR) X-ECH-M
More informationTIMBER SLIDING LOFT LADDER
POWER ARM SPRING HOUSING ANCHOR & LOCATION STOP ROLLER AR TWIST CATCH TIMER SLIDING LOFT LADDER A1 A2 A6 Installation and Operating Instrutions Read Carefully efore Installation Please hek you have all
More informationBerkley crib and changer Assembly Instruction
Wesite: www.sorellefurniture.om Berkley ri and hanger Assemly Instrution Important Information: Read all instrutions BEFORE assemling ri. KEEP INSTRUTIONS FOR FUTURE USE. Made in QHY, China Cri Warnings:
More informationX-ECT MX Electrical Cable Tie, X-EKS MX and X-EMTSC Conduit Clip Fastener
D X-ECTMX, X-EKSMX, X-ECT MX Electrical Cable Tie, X-EKS MX and Conduit Clip Fastener Product data Dimensions X-ECT MX X-EKS MX X-EKSC MX 18 X-GHP 20 X-GN 27 X-EGN 14 X-U 16/22/27 4 12.5 24.5 19 24.9 14
More informationHilti X-BT Threaded Fastener Specification. Supplement 02/2012. X-BT threaded fasteners for use in nuclear power plants
Hilti X-BT Threaded Fastener Specification Operating instructions: DX 450-SCT Supplement 02/2012 X-BT threaded fasteners for use in nuclear power plants February 2012, revised August 2012 Early strength
More informationFasteners. For Use in. Stainless. Steel Sheets. Revised 108
Fasteners For Use in Stainless Steel Sheets Revised 108 FASTENERS FOR USE IN STAINLESS STEEL SHEETS One of the very basics of self-clinching is that the fastener must be harder than the host sheet. Only
More information4600 INSTALLATION INSTRUCTION W/ 2190
1 STILE PREPARATION DOOR VERTIAL L STRIKE PREPARATION ALUMINUM FRAME.218 1.594 5/32" OFFSET (SEE STEP-8) 1 1/4" RIVNUT INSTALLATION FOR SINGLE OR DUAL LEVERS ON ALUMINUM STILE 5/32" OFFSET (SEE STEP-9)
More informationDIRECT FASTENING SYSTEMS. Hilti. Outperform. Outlast.
DIRECT FASTENING SYSTEMS. Hilti. Outperform. Outlast. Powder-Actuated Tools and Fasteners DX - Light Tools DX 460-F8 Page 140 DX 460 MX Page 141 Consumables X-U, X-C, X-FS, X-HS U, X-M, X-EM Page 142 Insulation
More informationCustomer Helpline No. (01773)
Maintenane The ladder and all other wooden parts an be varnished to protet and extend its life. Lubriate all moving metal parts annually. Srews and nuts should be heked from time to time and tightened
More informationDYNABOLT PLUS ANCHORS DYNABOLT PLUS. Anchor Details. Installation Ramset Regions. Site Map. Home Page. Performance. Next Page. Date of Issue: 9/98
Date of Issue: 9/9 Dynabolt Plus is a general purpose all steel medium duty through fixing for masonry and concrete. For fixing to Concrete, solid and hollow brick, masonry, natural stone. Surface Finish
More informationINSTALLATION GUIDE. 5" Balustrade System
5" Balustrade System PARTS LIST ITEM QTY A PORCH POST INSTALLATION KIT (PPK6) (SEE STEP 3C) 5 1/2" x 5 1/2" Trim Collar 2 2" Wide x 1 1/2" x 2" Angle Bracket 4 MATERIALS NEEDED INSTALLATION GUIDE #14 x
More informationReprint from IASTED International Conference on Signal and Image Processing (SIP 99). Nassau, Bahamas, October, 1999.
Reprint from IASTED International Conferene on Signal and Image Proessing (SIP 99). Nassau, Bahamas, Otober, 1999. 1 Filter Networks Mats Andersson Johan Wiklund Hans Knutsson Computer Vision Laboratory,
More informationTex-452-A, Rotational Capacity Testing of Fasteners Using a Tension Measuring Device
Using a Tension Measuring Device Contents: Section 1 Overview...2 Section 2 Definitions...3 Section 3 Apparatus...4 Section 4 Part I, Rotational Capacity Testing...5 Section 5 Part II, Values for Fasteners
More informationAnatomy of a 3LT Tripod & AirHed
User Manual Anatomy of a 3LT Tripod & AirHed Release Plate Lok Tri-Mount Plate Central Column Release Plate Para-Lok Pano Clamp Lok* Collar Loking Ring Leg Cath Hinge Loking Knob Para-Lok Pan Base Boots
More informationS-BT screw-in stainless steel and carbon steel threaded studs
S-BT screw-in stainless steel and carbon steel threaded studs Product data Dimensions S-BT-MR M10/15 SN 6 S-BT-MR M10/15 SN 6 AL**) S-BT-MR W10/15 SN 6 S-BT-MR W10/15 SN 6 AL**) S-BT-MR M10/15 SN 5 ***)
More informationAnchor HSA Fastening. Technology Manual HSA. Stud anchor. Version /
Anchor HSA Fastening Stud anchor Technology Manual HSA Stud anchor Version 2016-09 09 / 2016 1 HSA Stud anchor Anchor version Benefits HSA Carbon steel with DIN 125 washer HSA-F Carbon steel hot dipped
More informationSTEEL CANTILEVER TYPE E MICHIGAN DEPARTMENT OF TRANSPORTATION NOTE: EDGE OF SIGN VARIABLE 12" (MAX) 5'-0" COLUMN CAP 9'-5" (MAX) (TYP) DETAIL C
EDGE OF SIGN VARIABLE 12" (MAX) 25'-0" OLUMN AP 9'-5" (MAX) DETAIL END AP 1'-6" 4'-0" ARMS OPTIONAL SPLIE SIGN SIGN AND ARMS JP 1'-3" (MIN) 5'-0" 0.4 x L (MAX) OPTIONAL SPLIE VAIRES (25'-0" MAX) SEE ONTRAT
More informationProcedure for Wrench Calibration and Snug Tightening
Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure
More informationEuropean Technical Assessment. ETA-14/0426 of 21 December English translation prepared by DIBt - Original version in German language
European Technical Assessment ETA-14/0426 of 21 December 2016 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction
More informationProducts for fixing to Steelwork and Decking
Products 8.0 Beam Clamp - Single Support 8.1 Universal Joint for any variable Angle Adjustment 8.2 Beam Clamp TCS for Header Rails 8.3 Beam Clip for Cross Support/ Dimensioning of Bolts 8.4 Beam Clip for
More informationInvestigate index notation and represent whole numbers as products of powers of prime numbers (ACMNA149) a) 36 b) 100 c) 196 d) 441
Teaher Notes 7 8 9 10 11 12 Aim TI-Nspire CAS Investigation Student 120min The number 12 has six fators: 1, 2, 3, 4, 6 and 12. The number 36 has more fators. Whih number would have the greatest number
More informationwww. ElectricalPartManuals. com TypeCW Power Relay Descriptive Bulletin Page 1
November, 1 976 Supersedes DB 41-245, dated July, 1971 E, D, C/21 4/DB Westinghouse Eletri Corporation Relay-Instrument Division Newark, N.J. 711 For Exessive or Reverse Power Detetion CW for Single Phase
More informationCONTENTS. Hammerscrews White Zinc Plated 2 Hammerscrews Stainless Steel A Nylon Frame Anchors Yellow Zinc Plated 3 Nylon Plug 3
C CONTENTS CONTENTS PAGE 1 HAMMERSCREWS Haerscrews White Zinc Plated 2 Haerscrews Stainless A2-304 2 2 NYLON FRAME ANCHOR Nylon Frame s Yellow Zinc Plated 3 Nylon Plug 3 3 WINDOW FRAME ANCHOR Window Frame
More informationHilti HIT-HY 200 with HIT-Z
Hilti Injection Mortar System Benefits Hilti -R 500 ml foil pack (also available as 330 ml foil pack) Static mixer no cleaning required: zero succeptability to borehole cleaning conditions with dry and
More informationEuropean Technical Assessment. ETA-14/0426 of 15 December English translation prepared by DIBt - Original version in German language
European Technical Assessment ETA-14/0426 of 15 December 2014 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction
More informationFramo 80. Siconnect Framo 80 Beam Section TP F 80 Group: A410
Framo 80 15Framo 80 Beam Section TP F 80 Group: A410 Galvanised hollow-box-section for fabrication of steel frames. Designed for both simple two-dimensional supports and complex volumetric arrangements.
More informationExperiment (2) Metal Casting and Foundry 1. Objective: 2. Background: 3. Theory: Classification of molding and castings processes.
Experiment (2) Metal Casting and Foundry Dr. Mohammad Al-tahat Department of Industrial Engineering. University of Jordan. Lab. Of Manufaturing Proesses. Course No: 906412 1 1. Objetive: The main objetive
More informationContents 04LEAN0804-V1. Side Panels. Fixing Kit. Nail Bag & Ironmongery. For Assistance Please Contact Customer Care on
04LAN0804-V1 Contents Please retain Instrutions and label (attahed to your building for future referene See bak of instrutions for Combi greenhouse assembly Side Panels 1 2 3 Before ommening assembly make
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.
Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
FASTENER AND HARDWARE GENERAL REQUIREMENTS 1. DESCRIPTION This section contains general requirements for common hardware installation. Covered are selection and installation of cotter pins, installation
More informationChemical composition. Type 2 as per F568: C ( ); P (max 0.048); S (max 0.058); Mn (min 0.74); B (min );
BS EN 14399 HIGH STRENGTH STRUCTURAL BOLTING FOR PRE LOAD Direct comparison as an alternative to ASTM HSFG Bolts ASTM A325M Type 1, ASTM A490M Type 1 or 2 BS EN 14399-3:2005 Grade 8.8 and 10.9 Chemical
More informationPEC-TA Cast-in Channels and Bolts. Certified German quality for high-end fixing solutions. Advantages of using PEC Cast-in Channels.
Fixing Technology s and Bolts PEC Cast-in Channels are ideally suited for quick, reliable and cost-efficient fixing of different construction elements. The possibility of making simple and flexible adjustments
More informationHUS3 redundant SCREW ANCHOR. Technical Datasheet Update: Dec-17
HUS3 redundant SCREW ANCHOR Technical Datasheet Update: Dec-17 HUS3 Screw anchor Ultimate performance screw anchor for redundant fastening applications Anchor version HUS3-H (R) HUS3-C HUS3-A Benefits
More informationElectronic Damper Actuators
for dampers up to. square feet or. square meters based upon 4 in.lb. per square foot Desription The and are miroproessor based atuators with onditioned feedbak that operate on 4 volt AC nominal power supply.
More informationElectronic Damper Actuators
brushless DC driven atuators for dampers up to. square feet or. square meters based upon 4 in.lb. per square foot Desription The and are miroproessor based atuators with onditioned feedbak that operate
More informationBolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy
Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy steel: 4, 5, 6, 8, 10, 12 2- Bolts made of stainless
More informationSEBASTIAN TUB FAUCET INSTALLATION
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, bathtub,
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationMicro-Piezoelectric Head Technology of Color Inkjet Printer
DPP2: International Conferene on Digital Prodution Printing and Industrial Appliations Miro-Piezoeletri Head Tehnology of Color Inkjet Printer Takao Mimura & Shinri Sakai SEIKO EPSON Corporation Shiojiri-shi,
More informationCast-in Ferrule Connections Load/Displacement Characteristics in Shear
Cast-in Ferrule Connections Load/Displacement Characteristics in Shear Ian Ferrier 1 and Andrew Barraclough 2 1 Product Manager - Connections, ITW Construction Systems ANZ. 2 Research and Development Manager,
More informationFace Mount to Through-the-Post Mount
Face Mount to Through-the- Mount Cable Runs through Two Corners When going around two corners, it s necessary to tension the cable from both ends as shown in Deck 4. Use the 672 series The tensioning devices
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More information2011 IEEE. Reprinted, with permission, from David Dorrell, Design and comparison of 11 kv multilevel voltage source converters for local grid based
2 IEEE. Reprinted, with permission, from David Dorrell, Design and omparison of k multilevel voltage soure onverters for loal grid based renewable energy systems. IECON 2-37th Annual Conferene on IEEE
More informationCAM SYSTEM. Eccentric self-locking clamping devices. Set. CAM SYSTEM t. CAM SYSTEM t. Set. CAM SYSTEM s pag CAM SYSTEM s pag.
Eccentric self-locking CAM SYSEM Set CAM SYSEM t pag. 12 CAM SYSEM t pag. 126 Set CAM SYSEM s pag. 127 CAM SYSEM s pag. 128 EDGE CLAMP pag. 130 123 CAM-SYSEM eccentric self-locking he CAM SYSEM has been
More informationGovernment Letters Job Reference 18 21
Hilti X-CR Nail Product Information 2 6 X-CR Nails DX 460 Tool DX 36 Tool Technical data 7-11 Government Letters 12 16 Country of Origin 17 Job Reference 18 21 Make your submission simple! To download
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This
More informationNotes on Dielectric Characterization in Waveguide
Notes on Dieletri Charaterization in Waveguide R.Nesti, V. Natale IRA-INAF Aretri Astrophysial Observatory 1. Theory Let's suppose we have to haraterize the eletromagneti properties of a dieletri material,
More informationA001 RUE JEANNE-MANCE RUE OLMSTEAD AVENUE MCARTHUR SITE PLAN A002 1:500 NEW TWO STOREY ELEMENTARY SCHOOL
RUE JEANNE-MANE RUE OLMSTEAD NEW TWO STOREY ELEMENTARY SHOOL NOUVELLE ÉOLE ÉLÉMENTAIRE À DEUX ÉTAGES ÉLÉVATION DU REZ-DE-HAUSSÉE : 64,91 m EXISTING SHOOL TO BE RENOVATED EXISTING GYMNASIUM EXISTING TRAINING
More informationTrusted ICC ES. Issued 06/2018 HILTI, INC. Evaluation. report, or as to any. ICC-ES Evaluation
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 4185 Issued 06/2018 This report is subject to renewal 06/2019. SECTION: 05 05 23
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationNotes. Modifications and constructional corrections arising particularly from technological development excepted.
Notes Our service staff and application en gineers will be pleased to offer you their assistance to answer your questions or to work out in cooperation with you specific solutions with the aid of our own
More informationInstallation and Assembly Manual: Vector Pro II
Installation and ssembly Manual: Vector Pro II Models: PJF2-UNV, PJF2-UNV-S R This product is intended for use with U isted products and must be installed by a qualified professional installer. Maximum
More informationSWAY BRACE PIPE ATTACHMENT FIG. 010
Function: Designed for bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system used in conjunction with a PHD Manufacturing structural attachment fitting,
More informationTightening of Structural Joints
The design, fabrication, assembly and inspection of steel structures using metric high strength structural bolts and nuts to AS 1252 are covered in AS 4100 - SAA Steel Structures Code which should be referred
More informationPETSPRING, LLC MEADOWLAKE RICHMOND AVENUE, HOUSTON, TEXAS 77057
PETSPRING, LL SLATTERY TAKETT ARHITETS, LLP PETSPRING, LL REG D I STERED DA V I J. SL ARH A T T E RY I TET S T A T E 1 2 1 6 4 O F T E X A S DIGITALLY SIGNED: 06/11/2018 ARHITET SLATTERY TAKETT ARHITETS,
More informationChapter 23. Garage Construction
Chapter 23. Garage Construction 23.1 ESTABLISHING CHALK LINES 23.2 MEASURING AND CUTTING WALL PLATES 23.3 MARKING WINDOW & DOOR LOCATIONS ON EXTERIOR WALL PLATES 23.4 MARKING STUDS ON EXTERIOR WALL PLATES
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationBroaching-Type Fasteners Series CKF2 & CKFS2
Broaching-Type Fasteners CKF2 & CKFS2 CKF2 and CKFS2 broaching-type fasteners are designed for use on printed circuit boards and on most brittle or hard materials; such as, glass laminates, epoxy or resin
More informationWave Bike Rack specs SPECS AND INSTALL INSTRUCTIONS. Deluxe Wave Style Bike Rack. Series Names & Model # s. Product maintenance. Thermoplastic Coating
SPES ND INSTLL INSTRUTIONS Deluxe Wave Style ike Rack SKU: Series Names & Model # s 8 F7WIRQ InGround Post Mount Wave ike Racks Wave ike Rack specs KP/G3, KP/G5, KP/G7, KP/G9, KP/G11, KP/G13 Plate Surface
More informationUmbrella Inserts and Stubby Screens
ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7+ Adhesive Umbrella Inserts
More informationFAAST DEMONSTRATION UNIT CONSTRUCTION MANUAL. designs supplied by. re:creation
FAAST DEMONSTRATION UNIT CONSTRUCTION MANUAL designs supplied by CONTENTS FAAST DEMO UNIT #1 - GLASS SHOWCASE 2 FAAST DEMO UNIT #1 - UNIT CONSTRUCTION 3 CENTRAL GRAPHIC FRAMEWORK CONSTRUCTION 4 SMOKE RESISTOR
More informationLarge Diameter Tapcon
CONCRETE ANCHORING SPECIALISTS Large Diameter Tapcon (LDT ) Anchors Finished head, Removable Anchor DESCRIPTION/SUGGESTED SPECIFICATIONS Self-threading Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE The
More informationInstruction Manual for installing
Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS CE Marked EN 14399-9 TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies...
More informationInstruction Manual for installing
Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies... 2 Tightening
More informationMounting systems for solar technology
Mounting systems for solar technology ASSEMBLY INSTRUCTIONS Crosshook 3S CrossHook 4S GB Table of contents TABLE OF CONTENTS THE COMPANY SAFETY REGULATIONS MATERIALS REQUIRED TOOLS REQUIRED ASSEMBLY 2
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationEasy Step by Step Manual
Easy Step by Step Manual Teletower Mini XL Wall-Floor installation The tower packages #1-#2-#3 Open Base Package #1 for the main tower parts. Here you see the three tower tubes (H-Head, M-Middle, F-Feed)
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationCIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD METAL SCREWS. 6 x 3/4 P/N x 1 METAL SCREW P/N x 3/4 METAL SCREW
A21-1 1160 CIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD S For light duty applications in solid materials Color coded diameters for easy identifi cation Acid resistant NYLON FLANGED:
More informationENGINEERED BUILDING PRODUCTS. CycloneTie CT1200 CT900 CT600 CT400 CT180. mitek.com.au
ENGINEERED BUILDING PRODUTS yclonetie T1200 T900 T600 T400 T180 mitek.com.au Ti e FOR ROOF SEURITY UNDER EXTREME WIND ONDITIONS APPLIATION: ycloneties are used to secure purlins, rafters and trusses to
More informationToyota Tacoma SliderStep Installation Fits 05 and later Tacoma Double and Extra Cab Pickup Trucks
Toyota Tacoma SliderStep Installation Fits 05 and later Tacoma Double and Extra Cab Pickup Trucks NOTE: The Step Plate (piece with Slee Logo) is now a bolt on piece that gets added when sliders are installed.
More informationDesign Guide Pryda Connectors for Steel Framing
Pryda Connectors for Steel Framing Copyright: (c) Pryda Australia A Division of ITW Australia November 2012 November 2012 Design Guide Pryda Connectors for Steel Framing INDEX General Notes General information
More informationSuited to vehicle/s SIDE RAIL 2 DOOR (SWB) SIDE RAIL 4 DOOR (LWB) WARNING
Part Number Product Description Suited to vehicle/s Fitting Kit Number 4450200 SIDE RAIL 2 DOOR (SWB) 6172268 4450210 SIDE RAIL 4 DOOR (LWB) 6172253 ALSO, NOTE THE FOLLOWING: WARNING This product must
More informationAverage Current Mode Interleaved PFC Control
Freesale Semiondutor, n. oument Number: AN557 Appliation Note ev. 0, 0/06 Average Current Mode nterleaved PFC Control heory of operation and the Control oops design By: Petr Frgal. ntrodution Power Fator
More information