HPD Aerated concrete anchor. Approvals / certificates. Basic loading data (for a single anchor)

Size: px

Start display at page:

Download "HPD Aerated concrete anchor. Approvals / certificates. Basic loading data (for a single anchor)"

Victor Norris
5 years ago
Views:

1 HPD Anchor version HPD Benefits - anchor for autoclaved aerated concrete - maximum use of base material capacity - setting without drilling Autoclaved aerated concrete Fire resistance Sprinkler approved Approvals / certificates Description Authority / Laboratory No. / date of issue Allgemeine bauaufsichtliche Zulassung (national approval in DIBt, Berlin Z / Germany) a) Fire test report IBMB, Braunschweig UB 3077/3602-Nau- / Assessment report (fire) warringtonfire WF /A / Sprinkler VdS, Cologne G / a) All data given in this section according Z , issue Basic loading data (for a single anchor) All data in this section applies to - Correct setting (See setting instruction) - No edge distance and spacing influence - Autoclaved aerated concrete (AAC) - Load data given in the tables is independent of load direction Minimum base material thickness 432

2 Recommended loads Non-cracked AAC a) Cracked AAC Anchor size M6 M8 M10 M6 M8 M10 Recommended load for a single anchor AAC 2 [kn] 0,4 0,4 0, AAC 4, AAC 6 [kn] 0,8 0,8 1, P 3,3 [kn] 0,6 0,6 0, P 4,4 [kn] 0,8 0,8 1, P 3,3 [kn] ,6 0,6 0,8 P 4,4 [kn] ,8 0,8 1,2 Recommended load for a group of two anchor with a spacing 100mm s 200mm AAC 2 [kn] 0,4 0,4 0, AAC 4, AAC 6 [kn] 0,8 0,8 1, P 3,3 [kn] 0,6 0,6 0, P 4,4 [kn] 0,8 0,8 1, P 3,3 [kn] ,6 0,6 0,8 P 4,4 [kn] ,8 0,8 1,2 Recommended load for a group of two anchor with a spacing s 200mm AAC 2 [kn] 0,6 0,6 0, AAC 4, AAC 6 [kn] 1,1 1,1 1, P 3,3 [kn] 0,8 0,8 1, P 4,4 [kn] 1,1 1,1 1, P 3,3 [kn] ,8 0,8 1,1 P 4,4 [kn] ,1 1,1 1,7 a) in case of small sized AAC blocks (<= 250mm x 500mm x thickness) the recommended load has to be reduced with a factor 0,6. Materials Mechanical properties of HPD Anchor size M6 M8 M10 Carbon steel [N/mm²] Nominal tensile strength f uk Stainless steel [N/mm²] Carbon steel [N/mm²] Yield strength f yk Stainless steel [N/mm²] Stressed cross-section A s [mm²] 20,1 36,6 58 Moment of resistance W [mm³] 12,7 31,2 62,3 Char. bending resistance Carbon steel [Nm] M 0 Rk,s Stainless steel [Nm] The recommended bending moment shall be calculated by dividing the characteristic bending moment by 1,4 and 1,25 09 / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

3 Material quality Part All parts HPD HPD (stainless steel) Material Carbon steel, galvanised to min. 5 μm Stainless steel Anchor dimensions Anchor size M6 M8 M10 Minimum thickness of fixture t fix,min [mm] Maximum thickness of fixture* t fix,max [mm] Anchor diameter d 1 [mm] 9,8 11,8 13,8 Length of the expansion sleeve l c [mm] 70 Length of the cone l d [mm] 12 Setting Installation equipment Anchor size M6/10 M6/30 M8/10 M8/20 M10/10 M10/30 Manual setting tool HPE-G HPE-G HPE-G HPE-G - - (to be used with a hammer) 6/10 6/30 8/10 8/20 Setting tools Machine setting HPE-M HPE-M (to be used with a rotary hammer /10 10/30 in pure hammering mode) 434

Setting instruction Insert the cone bolt by hammering it in, until setting tool touches surface. Insert the expansion sleeve over the threaded rod.

4 Setting instruction Insert the cone bolt by hammering it in, until setting tool touches surface. Insert the expansion sleeve over the threaded rod. Bash in the sleeve by hammering or with the machine setting tool. Tighten the nut until the blue ring becomes visible. Setting details: depth of drill hole h 1 and effective anchorage depth h ef Visible setting control (blue ring) h ef t fix h min Setting details HPD Diameter of clearance hole in the fixture M6 M8 M10 d f [mm] Effective anchorage depth h ef [mm] Torque moment T inst [Nm] Width across SW [mm] / 2014 These pages are part of the Anchor Fastening Technology Manual issue September

Base material thickness, anchor spacing and edge distance Anchor size M8 M10 M12 Minimum base material thickness h min [mm] 175 Minimum Of anchors in a group s min,anchor [mm] 100 / 200 spacing Of

5 Base material thickness, anchor spacing and edge distance Anchor size M8 M10 M12 Minimum base material thickness h min [mm] 175 Minimum Of anchors in a group s min,anchor [mm] 100 / 200 spacing Of anchor groups s min,group [mm] 600 Minimum to member edge and edge to vertical joints [mm] distance to horizontal joints c min,2 [mm] s min,anchor c min,2 s min,group hmin s min,group Axis of the plate s min,anchor Allowable fixing area for anchors of roof and ceiling plates according DIN 4223 Width of plate 436

HK I. Anchor size (carbon steel) HK6 HK6L HK8 Resistance F Rk [kn] 2,0 5,0 5,0

HK I. Anchor size (carbon steel) HK6 HK6L HK8 Resistance F Rk [kn] 2,0 5,0 5,0 HK HK I Anchor version Benefits - well proven - small drill bit diameter - for fixing in cracked concrete, redundant fastening only, e.g. suspended ceilings a ) Redundant fastening only Approvals / certificates