ASSEMBLY IN STRUC TIONS

Size: px

Start display at page:

Download "ASSEMBLY IN STRUC TIONS"

Hugh Rogers
5 years ago
Views:

1 3-in-1 Stainless Five Burner Gas Grill ASSEMBLY IN STRUC TIONS Model GAS9556AS / GAS9556ASO

2 ASSEMBLY INSTRUCTIONS: READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT. The following tools are required to assemble this Cuisinart 5 Burner Gas Grill: Phillips Screwdriver Pliers or Wrench PARTS LIST: 1 1 Front Right Leg 2 1 Front Panel 3 1 Front Left Leg 4 1 Side Panel 5 1 Left Side Panel 6 1 Cart Brace 7 1 Cart Base 8 1 Left Rear Leg 9 1 Back Panel 10 1 Right Rear Leg 11 1 Side Burner Grate 12 5 Heat Tents 13 1 Side Burner Knob 14 1 Right Side Control Panel Grease Cup 1 Warming Rack 1 Heat Shield 1 Right Side Table 1 Left Side Table 1 Grill Body 1 Left Side Control Panel 4 Casters 3 Cooking Grates 1 Grease Tray 1 Griddle 1 Smoke Tube 2 Griddle Hooks 1 Bar Note: Most hardware is pre-attached to the grill. You may need to loosen some screws partially while others may need to be removed in order to assemble parts. The screws that you remove will be re-used so don t misplace this hardware. Extra screws are included in a small bag with the owners manual. 1

4 FRONT PANEL Step 1 Loosen 6 screws 3-4 turns Do not remove screws Attach FRONT PANEL 2 using keyholes Tighten 6 screws NOTE: Before tightening keyhole screws, make sure panels are aligned. Step 2 SIDE PANEL Loosen 3 screws Attach SIDE PANEL Tighten 3 screws on SIDE PANEL 4 3

5 Step Loosen 2 screws Attach LEFT SIDE PANEL Tighten 2 screws on LEFT SIDE PANEL 5 5 LEFT SIDE PANEL CART BRACE Step 4 Remove 6 screws. Attach CART BRACE. 6 Tighten two screws on CART BRACE. 6 Remove 2 screws Remove 2 screws 4

6 Step 5 Attach CART BASE 7 Make sure TANK BRACKETS are on this end. (See drawing below) Tighten 4 screws (Removed from Step 4) CART BASE 7 TANK BRACKETS Tighten 4 screws Step 6 BACK PANEL Remove 2 screws Loosen 6 screws Attach BACK PANEL Tighten 4 screws Remove 6 screws Remove 2 screws Remove 2 screws 5

7 Step 7 7 Attach CART BASE 7 to back legs CART BASE Tighten 4 screws (Removed from Step 6) LEFT SIDE PANEL 5 8 Screws removed from Step 6 9 Step 8 Attach LEFT SIDE PANEL 5 and CART BRACE 6 Tighten 4 screws CART BRACE 10 6

8 CASTERS Step 9 Lock CASTERS unlocked Attach CASTERS to legs 7 locked Step 10 Attach GRIDDLE HOOKS to LEFT SIDE PANEL 5 GRIDDLE HOOKS NOTE: Washer and nut used to attach GRIDDLE HOOKS go on the back side of LEFT SIDE PANEL. LEFT SIDE PANEL 7

9 TOP VIEW Step 11a 6 Loosen 2 bottom screws Loosen bottom screws CART BASE Step 11b 6 Install BAR Tighten 2 screws Tighten screw BAR Tighten screw CART BASE 8

10 Step 12 GRILL BODY Set GRILL BODY on cart Step 13 Remove 3 screws Remove screw GRILL BODY Remove screw Align GRILL BODY to cart Rotate CART BRACKETS upwards and tighten 4 screws CART BRACKETS Remove screw GRILL BODY Tighten screws Align Panels 9

11 Remove screw GRILL BODY Remove screw Step 14 Remove 3 screws Remove screw CART BRACKETS Align GRILL BODY to cart Rotate CART BRACKETS upwards and tighten 4 screws GRILL BODY Tighten screws Step 15 LEFT SIDE TABLE RIGHT SIDE TABLE Remove 3 screws and washers Remove screw and washer Remove screw and washer RIGHT SIDE CONTROL PANEL Remove screw 10

12 Step 16 LEFT SIDE CONTROL PANEL RIGHT SIDE CONTROL PANEL Loosen 4 screws Attach parts and tighten screws Align edges LEFT SIDE TABLE RIGHT SIDE TABLE Step 17 Loosen 4 screws Loosen 4 screws Attach LEFT SIDE TABLE using keyholes Do not tighten screws at this point in time LEFT SIDE TABLE 11

13 Step 18 Install screw and tighten. (screw was removed in Step 13) Step 19 Install screw and washer. (screw and washer were removed in step 15) Do not tighten screw at this time. Make sure panels are aligned Tighten 5 screws from Step 17 & 19 Align Panels 12

14 Step 20 Loosen 4 screws. Loosen 4 screws Attach RIGHT SIDE TABLE using keyholes. Do not tighten 4 screws at this time. RIGHT SIDE TABLE Step 21 Install screw and tighten (screw was removed in step 14) 13

15 Step 22 Install screw and washer (screw and washer were removed in step 15) Do not tighten screw at this time. Make sure panels are aligned and tighten 5 screws from Step 20 & 22 Align Panels Step 23 Install screw (removed in step 15) 4 14

16 Step 24a Remove WING NUT and remove burner. Install SIDE BURNER VALVE in control panel Rotate valve and tighten 2 screws to lock into place (see diagram step 24b below) SIDE BURNER VALVE BURNER VENTURI WING NUT Install burner and make sure BURNER VENTURI fits over VALVE NOZZLE VALVE NOZZLE Tighten WING NUT Step 24b Install SIDE BURNER KNOB KEY HOLES SIDE BURNER KNOB BEZEL SIDE BURNER VALVE STEM 15

17 Step 25a Attach WIRE CLIP to side burner SIDE BURNER WIRE CLIP SIDE BURNER VALVE Step 25b SIDE BURNER WIRE CLIP SIDE BURNER VALVE 16

18 Step 26 Attach IGNITOR WIRE to ELEC- TRODE ELECTRODE IGNITER WIRE Step 27 Install SIDE BURNER GRATE SIDE BURNER GRATE 17

19 Step 28 Loosen 2 screws Attach HEAT SHIELD and tighten screws HEAT SHIELD GREASE TRAY Step 29 Install GREASE TRAY and GREASE CUP through back of grill GREASE CUP 18

20 WARMING RACK Step 30 Install HEAT TENTS,COOKING GRATES and WARMING RACK COOKING GRATES HEAT TENTS Step 31 Store GRIDDLE on GRIDDLE HOOKS Store SMOKE TUBE SMOKE TUBE STORAGE GRIDDLE STORAGE 19

21 Model GAS9556AS Assembled AI9556AS/ASO The Boltz Group LLC Addison, Texas U.S.A Assembly Instructions for Model GAS9556AS / GAS9556ASO

CF9030 ASSEMBLY PROCEDURES

CF9030 ASSEMBLY PROCEDURES VERMONT PROCEDURES Step 1: Unpack carton. Tools Required: Knife or scissors; hammer; Philips or Robertson screwdriver Castings Box #5 Box #4 Box #1 Box #3 Box #2 Use the knife or scissors to cut the strapping