2300 Series DustPruf End Drive Conveyors

Transcription

1 00 Series DustPruf End Drive Conveyors Installation, Maintenance and Parts Manual Featuring: DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box Cottonwood Ave. TEL: TEL: Hartland, WI USA FAX: FAX: Rev. A For other service manuals visit our website at:

2 Table of Contents Introduction... Warnings - General Safety... Product Description... 5 Specifications Series DustPruf Flat Belt Conveyor Series DustPruf Cleated Belt Conveyor... 5 Conveyor Supports... 6 Maximum Distances:... 6 Specifications... 6 Installation... 7 Required Tools... 7 Recommended Installation Sequence... 7 Conveyors Up to ft (658mm)... 7 Conveyors Longer Than ft (658mm)... 7 Mounting Brackets... 8 Return Rollers... 9 Cleated Belt and 6 (5 5 mm) Wide Flat Belt Conveyors (0 60 mm) Wide Flat Belt Conveyors... 9 Proper Methods of Attachment to Side Rails... 0 Self-Drilling Screws... 0 Pre-Drill for Standard Screws... 0 Guiding... Preventive Maintenance and Adjustment... Required Tools... Standard Tools... Special Tools... Checklist... Lubrication... Maintaining Conveyor Belt... Troubleshooting... Cleaning... Conveyor Belt Replacement... Conveyor Belt Replacement Sequence... Belt Removal for Conveyor Without Stands or Gearmotor Mounting Package... Belt Removal for Conveyor With Stands and Gearmotor Mounting Package... Belt Installation for Conveyor without Stands or Gearmotor Mounting Package... Belt Installation for Conveyor with Stands and Gearmotor Mounting Package... Conveyor Belt Tensioning... 5 Conveyors with.5 ( mm) Diameter Pulleys... 5 Conveyors with Nose Bar Idlers... 6 Conveyor Belt Tracking... 6 V-Guided Belts... 6 Non V-Guided Belts... 6 Pulley Removal... 7 A - Idler Pulley Removal... 7 B - Drive Pulley Removal... 8 Bearing Removal & Replacement... 8 Removal... 8 Replacement... 9 Drive Pulley and Pulley Installation... 9 Drive Pulley Installation... 9 Idler Pulley Installation... 9 Nose Bar Bearing Replacement... 0 Notes... Service Parts... Drive Tail... Idler Tail... Nose Bar Idler End... " (5mm) and " (05mm) Wide Frame Assembly " (57mm) and " (60mm) Wide Frame Assembly (76 mm) Aluminum Side (8mm) Aluminum Side Low to Side Wiper Low to High Side (mm) Extruded Plastic... - Adjustable Guiding... - Tool-Less Adjustable Guiding (mm) Cleated Belt Guiding... (5mm) Cleated Belt Guiding... 5 (5mm) Cleated Belt Guiding... 6 Flared Side Guiding... 7 Flat Belt Stand Mount Assembly... 8 Cleated Belt Stand Mount Assembly... 8 Flat Belt Stand Mount Assembly for (60mm) Long Conveyors... 9 Cleated Belt Stand Mount Assembly for (60mm) Long Conveyors... 9 Connecting Assembly without Stand Mount... 0 Flat Belt Connecting Assembly with Stand Mount... 0 Cleated Belt Connecting Assembly with Stand Mount.. (5mm) to 6 (5mm) Flat Belt Return Roller... 8 (0mm) to (60mm) Flat Belt Return Roller... Cleated Belt Return Roller... Conveyor Belt Part Number Configuration... Return Policy... Dorner Mfg. Corp Rev. A

3 Introduction IMPORTANT Some illustrations may show guards removed. DO NOT operate equipment without guards. Upon receipt of shipment: Compare shipment with packing slip. Contact factory regarding discrepancies. Inspect packages for shipping damage. Contact carrier regarding damage. Accessories may be shipped loose. See accessory instructions for installation. Dorner s Limited Warranty applies. Dorner has convenient, pre-configured kits of Key Service Parts for all conveyor products. These time saving kits are easy to order, designed for fast installation, and guarantee you will have what you need when you need it. Key Parts and Kits are marked in the Service Parts section of this manual with the Performance Parts Kits logo. Dorner 00 series conveyors are covered by Patent Numbers 5,7,5, 6,98,98, 6,,8 and corresponding patents and patent applications in other countries. Dorner reserves the right to make changes at any time without notice or obligation Rev. A Dorner Mfg. Corp.

4 Warnings - General Safety A WARNING The safety alert symbol, black triangle with white exclamation, is used to alert you to potential personal injury hazards. A WARNING DANGER Climbing, sitting, walking or riding on conveyor will cause severe injury. KEEP OFF CONVEYORS. DANGER Dorner cannot control the physical installation and application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment or as part of a multiple conveyor system, CHECK FOR POTENTIAL PINCH POINTS and other mechanical hazards before system start-up. A WARNING DO NOT OPERATE CONVEYORS IN AN EXPLOSIVE ENVIRONMENT. A WARNING Loosening stand height or angle adjustment screws may cause conveyor sections to drop down, causing severe injury. SUPPORT CONVEYOR SECTIONS PRIOR TO LOOSENING STAND HEIGHT OR ANGLE ADJUSTMENT SCREWS. Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. A WARNING Gearmotors may be HOT. DO NOT TOUCH Gearmotors. Dorner Mfg. Corp Rev. A

5 Product Description Refer to Figure for typical components. Conveyor Gearmotor Mounting Package Figure 9 0 Gearmotor Guiding & Accessories 5 Mounting Brackets 6 Return Rollers Support Stand 8 Variable Speed Controller 8 9 Drive End 0 Idler/Tension End 7 Figure Specifications 00 Series DustPruf Flat Belt Conveyor 00 Series DustPruf Cleated Belt Conveyor 00 Series DustPruf Flat Belt Conveyor 0F M WW LLLL G D T S PA PD BB - Belt Type Profile (D side) Profile (A side) Motor Shaft Position Idler Tail Type Drive Tail Type Tracking / Mounting Brackets Conveyor Length Conveyor Width Document Language 00 Series DustPruf Cleated Belt Conveyor CF M WW LLLL G D T S PP C L SSSS - Cleat Spacing Belt Type Cleat Type Profiles Motor Shaft Position Idler Tail Type Drive Tail Type Tracking / Mounting Brackets Conveyor Length Conveyor Width Document Language Rev. A 5 Dorner Mfg. Corp.

6 Specifications Conveyor Supports Maximum Distances: = 8 (57 mm)** = 6 ft (89 mm)*** = 8 (57 mm) ** For Heavy Load Bottom Mount Package, mount support under gear head. *** For conveyors longer than ft (658 mm), install support at joint. Figure Specifications Figure Conveyor Width Reference (WW) Conveyor Belt Width.75 (mm) Maximum Conveyor Load* (See NOTE Below) Conveyor Startup Torque* Belt Travel Maximum Belt Speed* Belt Takeup 6 lb (6kg) in-lb (0.5Nm).75 (95mm) 50 lb (kg) in-lb (0.7Nm) 6 (5mm) 7 lb (kg) 8 in-lb (0.9Nm) 8 (0mm) 8 lb (8kg) 0 in-lb (.Nm) (05mm) 96 lb (kg) in-lb (.5Nm) 8 (57mm) 96 lb (kg) 5 in-lb (.7Nm).0 (88 mm) per revolution of pulley 6 ft/minute (80.5 m/minute) 0.8 (0 mm) of stroke = 0.75 (9 mm) of belt take-up (609mm) 96 lb (kg) 0 in-lb (.Nm) Conveyor Length Reference (LLLL).5 ft (57 mm) to 8 ft (586 mm) in 0. ( mm) increments** * See Ordering and Specifications Catalog for details. NOTE ** Conveyors longer than (658mm) are only available Maximum conveyor loads based on: in 6 (5mm) wide or wider. Non-accumulating product Product moving towards gearmotor Conveyor being mounted horizontal Dorner Mfg. Corp Rev. A

7 Installation NOTE Conveyor MUST be mounted straight, flat and level within confines of conveyor. Use a level (Figure, item ) for setup. Conveyors Longer Than 8 ft (8 mm). Locate and arrange conveyor sections by section labels (Figure, item ). Figure Figure Figure Installation Component List Conveyor frame (two sections if longer than 8 ft) Conveyor brackets Return rollers (for longer conveyors) Required Tools Figure. On tension end of the conveyor, identified with Figure 5 a label (Figure 5, item ), push in head plate assembly (Figure 5, item ): On both sides of conveyor, loosen and move cam tracking assemblies (Figure 5, item ) (if equipped) away from head plates, then loosen fastening screws (Figure 5, item ) and push head plate assembly inward. Hex-key wrenches: mm, 5 mm Level Torque wrench Recommended Installation Sequence Assemble conveyor (if required) Attach mounting brackets to conveyor Attach conveyor to stands (see accessory instructions) Install return rollers on conveyor (optional) Mount gearmotor mounting package (see accessory instructions) Attach guides/accessories (see page through page of Service Parts section for details) Figure 5. Roll out conveyor belt and place conveyor frame sections (Figure 6, item ) into belt loop. Figure 6 Conveyors Up to 8 ft (8 mm) No assembly is required. Install mounting brackets and return rollers. Refer to Mounting Brackets on page 8 and Return Rollers on page 9. Figure Rev. A 7 Dorner Mfg. Corp.

8 Installation. Join conveyor sections and install frame connector plates (Figure 7, item ) or connector/mount brackets (Figure 7, item ) and screws (Figure 7, item ) on both sides as indicated. Tighten screws to 60 in-lb (7 Nm). Figure 7 A WARNING Installing self-drilling screws into the DustPruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS. Figure 9 Figure 7 5. With a 5 mm hex-key wrench, rotate pinion gear (Figure 8, item ) to tension the conveyor belt. Tighten fastening screws (Figure 8, item ) on both sides of conveyor to 80 in-lb (9 Nm). For proper tensioning, refer to Conveyor Belt Tensioning on page 5. Figure 8 Figure 9 Figure 0 Figure 8 6. Install mounting brackets and return rollers. Refer to Mounting Brackets on page 8 and Return Rollers on page If equipped with cam tracking assemblies (Figure 5, item ), reposition and adjust belt tracking. Refer to Conveyor Belt Tracking on page 6. Mounting Brackets. Locate brackets. Exploded views shown in Figure 9 for flat belt & Figure 0 for a cleated belt. Figure 0. Remove screws (Figure 9, item ) or (Figure 0, item ), washers (Figure 9, item ) or (Figure 0, item ), nuts (Figure 9, item ) or (Figure 0, item ) from brackets. IMPORTANT For proper methods of attachment to conveyor side rail see page 0.. Locate and retain self-drilling screws (Figure 9, item ). Dorner Mfg. Corp Rev. A

9 Installation NOTE For maximum support distance see page 6.. Measure an equal distance (Figure, item ) from end of head plate (on both sides of conveyor) and mark placement of mounting brackets (Figure, item ). Fasten mounting brackets to conveyor with mounting screws (Figure, item ) following proper methods of attachment instructions on page 0. Return Rollers Cleated Belt and 6 (5 5 mm) Wide Flat Belt Conveyors. Locate return rollers. Exploded views shown in Figure & Figure. Figure NOTE Mounting brackets for flat belt conveyors shown. Figure Figure Figure Figure 5. Fasten brackets (Figure, item ) to support stand (Figure, item ) with mounting screws (Figure, item ), washers (Figure, item ) and nuts (Figure, item 5). Figure. Remove screws (Figure, item ) & (Figure, item ) and clips (Figure, item ) from roller assembly.. Install roller assemblies (Figure 5, item ) as shown. Tighten screws (Figure 5, item ) to 60 in-lb (7 Nm). Figure 5 Figure Figure (0 60 mm) Wide Flat Belt Conveyors Figure. Locate return rollers. Exploded view shown in Figure 6. Figure 6 Figure 6. Remove screws (Figure 6, item ) and clips (Figure 6, item ) from roller assembly Rev. A 9 Dorner Mfg. Corp.

10 Installation. Install roller assembly as shown (Figure 7, item ). Tighten screws (Figure 7, item ) to 60 in-lb (7 Nm). Figure 7 Figure 8 Figure 7 Proper Methods of Attachment to Side Rails Figure 8. With a cordless drill or equivalent install self-drilling screws (Figure 8, item ). Use high speed setting to drill through side wall. Once the tap portion is started switch drill power to a lower speed. Do not fully tighten with drill.. Hand tighten the screws to secure (Figure 9). Recommended torque is 50 in.lbs (7 Nm). A WARNING Installing self-drilling screws into the dustpruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS. Figure 9 The 00 DustPruf side rail is designed for self-drilling attachment of brackets and accessories. This can be done in two methods: self-drilling screws or pre-drill for standard screws. Self-Drilling Screws All Dorner accessories are provided with /-0 self-drilling screws.. Locate and hold bracket (Figure 8, item ) to side rail. Hole should line up with notch (Figure 8, item ) in side rail. Figure 9 Pre-Drill for Standard Screws The DustPruf side rail will also accept standard screws. M6-.0 and /-0 are acceptable. Strength grade 8 is recommended.. Locate and hold bracket (Figure 0, item ) to side rail. Hole should line up with notch (Figure 0, item ) in side rail. Mark the hole locations with a center punch (Figure 0, item ) and remove the bracket. Figure 0 Figure 0 Dorner Mfg. Corp Rev. A

11 Installation. Drill the hole locations (Figure, item ) with a /6" drill bit (Figure, item ). Figure Figure. Position and hold bracket (Figure, item ) to side rail. With a standard M6-.0 or /-0 screw, install screws (Figure, item ) with cordless drill or equivalent. Do not fully tighten with drill. Figure Guiding A WARNING Installing self-drilling screws into the DustPruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS. Due to the DustPruf construction ALL guiding must be located and installed by the end user. Take care in locating retaining clips prior to final installation.. Lay out retaining clip (Figure, item ) locations. The end clips should be no greater than " (Figure, item ) from end of the conveyor. NOTE Profile -09, Low to High Side shown below. For other guide profile layouts see pages page 7 thru page 7. Figure 5 Figure. Hand tighten the screws to secure (Figure ). Recommended torque is 50 in.lbs (7 Nm). Figure Figure. Hold guide (Figure, item ) and retaining clips (Figure, item ) to conveyor side rail. Install selfdrilling screws (Figure, item 5) following the Proper Methods of Attachment to Side Rails on page 0 procedure. Figure Rev. A Dorner Mfg. Corp.

12 Preventive Maintenance and Adjustment Required Tools Standard Tools Hex-key wrenches:.5 mm, mm, 5 mm Arbor press Special Tools Bearing Puller Tool (or equivalent) 509 Bearing Installation Tool (Bearing Pusher) 5606 Bearing Removal Tool Checklist Keep service parts on hand (see Service Parts section for recommendations) Keep supply of belt cleaner (part # 6569) Clean entire conveyor and knurled pulley while disassembled Replace worn or damaged parts Damage to V-guide indicates: Twisted or damaged conveyor frame Dirt impacted on pulleys Excessive or improper side loading Cleaning IMPORTANT Do not use belt cleaners that contain alcohol, acetone, Methyl Ethyl Ketone (MEK) or other harsh chemicals. Use Dorner Belt Cleaner (part # 6569). Mild soap and water may also be used. Do not soak the belt. For /05 woven polyester and /06 black anti-static belts, use a bristled brush to improve cleaning. Conveyor Belt Replacement A WARNING Lubrication No lubrication is required. Replace bearings if worn. Maintaining Conveyor Belt Troubleshooting Inspect conveyor belt for: Surface cuts or wear Stalling or slipping Damage to V-guide Surface cuts and wear indicate: Sharp or heavy parts impacting belt Jammed parts Improperly installed bottom wipers (if installed) Accumulated dirt in wipers (if installed) Foreign material inside the conveyor Improperly positioned accessories Bolt-on guiding is pinching belt Stalling or slipping indicates: Excessive load on belt Conveyor belt or drive timing belt are not properly tensioned Worn knurl or impacted dirt on drive pulley Intermittent jamming or drive train problems Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Conveyor Belt Replacement Sequence Remove old conveyor belt: - Conveyor without Stands or Gearmotor Mounting Package - Conveyor with Stands and Gearmotor Mounting Package Install new conveyor belt Tension conveyor belt Dorner Mfg. Corp Rev. A

13 Preventive Maintenance and Adjustment Belt Removal for Conveyor Without Stands or Gearmotor Mounting Package. If equipped, remove bottom wipers (Figure 5, item ): Remove fastening screws (Figure 5, item ) then remove wiper. Belt Removal for Conveyor With Stands and Gearmotor Mounting Package A WARNING Figure 5 Figure 5. If equipped, remove return rollers and guiding and accessories from one side of conveyor.. On tension end of the conveyor, identified with a Figure 6 label (Figure 6, item ), push in head plate assembly (Figure 6, item ): On both sides of conveyor, loosen and move cam tracking assemblies (Figure 6, item ) (if equipped) away from head plates, then loosen fastening screws (Figure 6, item ) and push head plate assembly inward.. Place temporary support stands (Figure 7, item ) at both ends of the conveyor. Place an additional support stand under the drive motor (Figure 7, item ), if equipped. See WARNING. Figure 7 Removing mounting brackets without support under gearmotor will cause conveyor to tip, causing severe injury. PROVIDE SUPPORT UNDERNEATH THE GEARMOTOR WHEN CHANGING THE BELT Figure 7. Remove mounting brackets (Figure 7, item ) from one side of conveyor. (Reverse steps & of Mounting Brackets section beginning on page 8.) If equipped with heavy load drive package, remove brackets from side opposite drive cover (Figure 8, item ).. If equipped, remove bottom wipers (Figure 5, item ): Remove fastening screws (Figure 5, item then remove wiper (Figure 5, item ).. Remove conveyor belt. Figure Rev. A Dorner Mfg. Corp.

14 Preventive Maintenance and Adjustment. If equipped, remove return rollers, guiding and accessories from side opposite drive cover (Figure 8, item ). 7. Remove belt (Figure 0, item ) from conveyor. Figure 0 Figure 8 Figure 0 Belt Installation for Conveyor without Stands or Gearmotor Mounting Package. Orient belt so splice leading fingers (Figure, item ) point in the direction of belt travel as identified by the conveyor directional label (Figure, item ). Figure Figure 8 5. If equipped with heavy load drive package, remove drive support bracket (Figure 8, item ): Remove bracket screws (Figure 8, item ) then remove bracket (Figure 8, item ). 6. On tension end of the conveyor, identified with Figure 9 a label (Figure 9, item ), push in head plate assembly (Figure 9, item ): On both sides of conveyor, loosen and move cam tracking assemblies (Figure 9, item ) (if equipped) away from head plates, then loosen fastening screws (Figure 9, item ) and push head plate assembly inward. Figure. Slide belt onto the conveyor frame assembly.. Tension belt. Refer to Conveyor Belt Tensioning on page 5.. If equipped, install wipers, return rollers and guiding. Belt Installation for Conveyor with Stands and Gearmotor Mounting Package A WARNING Figure 9 Removing mounting brackets without support under gearmotor will cause conveyor to tip, causing severe injury. PROVIDE SUPPORT UNDERNEATH THE GEARMOTOR WHEN CHANGING THE BELT Dorner Mfg. Corp Rev. A

15 Preventive Maintenance and Adjustment. Ensure temporary support stands (Figure 7, item ) are placed at both ends of the conveyor. Place an additional support stand under the drive motor (Figure 7, item ), if equipped. See WARNING.. Orient belt so splice leading fingers (Figure, item ) point in the direction of belt travel as identified by the conveyor directional label (Figure, item ).. Install belt (Figure, item ) on conveyor. Lift conveyor slightly to avoid pinching belt on temporary support stands. Figure 5 Figure Figure. Re-install conveyor mounting brackets. Refer Mounting Brackets beginning on page 8, steps through If equipped with a heavy load drive package, re-install drive support bracket (Figure 8, item ). 6. Tension belt. Refer to Conveyor Belt Tensioning on page 5 7. If equipped, re-install wipers, return rollers and guiding. Figure. Adjust head plate assembly so end of conveyor frame aligns with or between the head plate tensioning marks (Figure, item & ). Replace belt if proper tensioning can not be obtained while aligning the end of the conveyor frame with or between the tensioning marks. See NOTE. Figure Conveyor Belt Tensioning A WARNING Figure Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Conveyors with.5 ( mm) Diameter Pulleys. On tension end of the conveyor, identified with a label (Figure, item ), adjust head plate assembly (Figure, item ): On both sides of conveyor, loosen fastening screws (Figure, item ) and rotate pinion gear (Figure, item ) to adjust head plate assembly. NOTE On pinion gear, do not exceed a torque of 5 in-lb (.8 Nm) for ( 05 mm) wide conveyors and 50 in-lb (.5 Nm) for an 8 (57 60 mm) wide conveyor. Over tensioning the conveyor belt could cause excessive pulley bearing load and early failure.. After adjusting proper tensioning, tighten fastening screws (Figure, item ) on both sides of conveyor to 60 in-lb (7 Nm).. If equipped with cam tracking assemblies (Figure, item 5), position against head plates and adjust belt tracking. Refer to Conveyor Belt Tracking on page Rev. A 5 Dorner Mfg. Corp.

16 Preventive Maintenance and Adjustment Conveyors with Nose Bar Idlers. On tension end of the conveyor, identified with a Figure 5 label (Figure 5, item ), adjust head plate assembly (Figure 5, item ): On both sides of conveyor, loosen fastening screws (Figure 5, item ) and rotate pinion gear (Figure 5, item ) to adjust head plate assembly. 5. If equipped with cam tracking assemblies (Figure 5, item 5) position against head plates and adjust belt tracking. Refer to Conveyor Belt Tracking, next section. Conveyor Belt Tracking V-Guided Belts V-guided belts do not require tracking adjustment. Non V-Guided Belts Non V-guided belt conveyors are equipped with belt tracking cam assemblies (Figure 7, item ) for belt tracking adjustment. Figure 7 6 BELT TRAVEL Figure 5. Adjust head plate assembly so the edge of the axle support plate (Figure 6, item ) is separated from the end of the conveyor (Figure 6, item ) by.5 (9 mm). Replace belt if proper tensioning can not be obtained within a distance of.50 (8 mm). See NOTE. Figure 6 5 Figure 6 NOTE.5 (9 mm) On pinion gear, do not exceed a torque of 5 in-lb (.8 Nm) for ( 05 mm) wide conveyors or 50 in-lb (.5 Nm) for an 8 (57 60 mm) wide conveyor. Over tensioning the conveyor belt could cause excessive pulley bearing load and early failure.. After adjusting proper tensioning, tighten fastening screws (Figure 5, item ) on both sides of conveyor to 60 in-lb (7 Nm). Figure 7 When adjusting belt tracking, always adjust the discharge end of the conveyor first. To adjust belt tracking:. Ensure head plate fastening screws (Figure 7, item ) on both sides of conveyor are tightened.. On both sides of conveyor, loosen two () cam fastening screws (Figure 7, item ). Adjust cams (Figure 7, item ) until indicator slots (Figure 7, item 5) are horizontal and facing end of conveyor. Then slide cam assemblies against head plates (Figure 7, item 6) and re-tighten cam fastening screws (Figure 7, item ) to 60 in-lb (7 Nm).. On the side toward which the belt is tracking, loosen head plate fastening screws (Figure 7, item ).. With the conveyor running, use a 5 mm hex-key wrench to rotate the tracking cam (Figure 7, item ) in small increments until the belt tracks in the center of the conveyor. Then while holding the cam in position, retighten the head plate fastening screws (Figure 7, item ) with a mm hex-key wrench to 60 in-lb (7 Nm). Dorner Mfg. Corp Rev. A

17 Preventive Maintenance and Adjustment Pulley Removal Figure 9 A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Leaving the conveyor belt in place, remove the desired pulley following the corresponding instructions below: A - Idler Pulley Removal B - Drive Pulley Removal A - Idler Pulley Removal. On one side of the conveyor, loosen two () head plate fastening screws (Figure 8, item ) and remove them. Figure 9. Pulley will slide out of opposite head plate and drop into slack of belt (Figure 0). Figure 0 NOTE To prevent damage to the head plates and pulley, be sure to remove them slowly because they are not attached to pulley. Figure 8 Figure 0. Slide spindle out of the belt loop. Figure 8. Remove the head plate (Figure 9, item ) from the conveyor frame Rev. A 7 Dorner Mfg. Corp.

18 Preventive Maintenance and Adjustment B - Drive Pulley Removal Bearing Removal & Replacement A WARNING Drive shaft keyway may be sharp. HANDLE WITH CARE.. On one side of the conveyor, loosen two () head plate fastening screws (Figure, item ) and remove. NOTE To prevent damage to the head plates, be sure to remove them slowly because they are not attached to pulley. Removal. Place bearing removal tool part #5606 (Figure, item ) below bearing (Figure, item ) with lip (Figure, item ) located in gap (Figure, item ) between bearing and spindle hub (Figure, item 5) as shown. Figure IMPORTANT Do not use any removed bearings. Replace them. 5 Figure Figure. Using puller part # (Figure, item ), remove and discard bearing. Figure Figure. Remove the head plate (Figure, item ) from the conveyor frame. Figure Figure Figure. Drive pulley will slide out of opposite head and drop into slack of belt.. Slide the drive pulley out of the belt loop. Dorner Mfg. Corp Rev. A

19 Preventive Maintenance and Adjustment Replacement. Inspect the head plates bearing seating surface (Figure 5, item ). If they are worn or damaged, replace. See Service Parts on page. Figure 5 Drive Pulley and Pulley Installation Drive Pulley Installation. With opposite head plate installed, position the drive pulley through the loop of the belt, into the opposite head plate.. Place the head plate (Figure 8, item ) and attach the head plate to the conveyor frame with the two () screws removed. Tighten screws 60 in-lb (7 Nm). Figure 8 Figure 5. Inspect spindle (Figure 6, item ). Replace if worn.. Slide bearing (Figure 6, item ) onto spindle. Figure 6 Figure 6. Using an arbor press or similar device, press bearing onto pulley shaft (Figure 7). Figure 8 Idler Pulley Installation. With opposite head plate installed, position the idler pulley through the loop of the belt, into the opposite head plate.. Place the head plate (Figure 9, item ) and attach the head plate to the conveyor frame with the two () screws removed and hand tighten. Figure 9 Figure 7 Figure 7 5. Repeat steps through for each bearing. Figure Rev. A 9 Dorner Mfg. Corp.

20 Preventive Maintenance and Adjustment Nose Bar Bearing Replacement. On both sides of conveyor, use a mm hex-key wrench to loosen cam fastening screws (Figure 50, item ) and slide cam assemblies toward the center of the conveyor. Figure 50 Figure 50. On both sides of conveyor, use a mm hex-key wrench to loosen head plate fastening screws (Figure 50, item ) to remove belt tension. Then remove belt from end of conveyor.. On one side of conveyor, use a mm and mm hex-key wrench to remove head plate fastening screws (Figure 50, item ) & (Figure 50, item ) and remove head plate (Figure 50, item ).. Slide bearing rods (Figure 5, item ) out side of conveyor and replace bearings (Figure 5, item ) as necessary. Figure 5 Figure 5 5. After replacing bearings, re-install head plate (Figure 50, item ). Use a mm hex-key wrench to tighten one () fastening screw (Figure 50, item ) to 0 in-lb (. Nm). Leave two () fastening screws (Figure 50, item ) loose for belt tensioning. 6. Re-install belt on end of conveyor, then tension the belt. See Conveyor Belt Tensioning on page Re-position the cam assemblies against the head plates and adjust belt tracking. See Conveyor Belt Tracking on page 6. Dorner Mfg. Corp Rev. A

21 Notes Rev. A Dorner Mfg. Corp.

22 Service Parts Drive Tail NOTE For replacement parts other than those shown in this section, contact an authorized Dorner Service Center or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo. Dorner recommends keeping these parts on hand. Nosebar Drive Spindle Kit Drive Spindle Kit OR 5 A & B Position 0 7 C & D Position 9069M Socket Head Screw, M6 x mm 05 Head Plate LH 07 Head Plate LH Drive Side, Position A and B 08 Head Plate RH Drive Side, Position C and D 5 BK Bearing Kit (x) BK Bearing Kit (x) 6 06 Head Plate RH M Socket Head Screw, M6 x 0 mm Tension Slide Bar 9 56WW Drive Spindle 76WW Nosebar Drive Spindle, Lagged 75WW Dual Output Drive Spindle 0 980MS Square Key, mm x mm A-WW Drive Spindle Kit, Position A and B - Grooved (Includes Items,, 5, 6 and 9) D-WW Drive Spindle Kit, Position C and D - Grooved (Includes Items,,, 5, and 9) NA-WW Nosebar Drive Spindle Kit, Position A and B - Lagged, Smooth (Includes Items,, 5, 6 and 9) ND-WW Nosebar Drive Spindle Kit, Position C and D - Lagged, Smooth (Includes Items,,, 5, and 9) WW = Conveyor width reference: 0, 0, 06, 08,, 8 & Dorner Mfg. Corp Rev. A

23 Idler Tail Service Parts 9 Idler Spindle Kit 0 Bearing Kit Head Plate, Left Hand 07-WW Spindle Kit with Bearings Magnet, 0.5" diameter x 0.5" long 506SSP Sleeve 5 06 Head Plate, Right Hand M Socket Head Screw, M6 x mm M Socket Head Screw, M6 x 0 mm Tension Slide Bar 9 T-WW Idler Spindle Kit, (Includes Items through 7) 0 BK Bearing Kit ( pack) BK Bearing Kit ( pack) WW = Conveyor width reference: 0, 0, 06, 08,, 8 & Rev. A Dorner Mfg. Corp.

24 Service Parts Nose Bar Idler End 5 Nose Bar Roller Kit Mounting Block, PLT Spindle Mounting Block, for (5mm) wide conveyor 076WW Flex-Link Bar, 07 Flex-Link Bar, for (5mm) wide conveyor 5 Outer Side Plate 6 Inner Side Plate, LH 5 7 Inner Side Plate, RH Head Plate Bar 7 WW Nosebar 8 WW Nosebar Rod P Knurl Pin, 0.5 DIA x 0.97 Lg Nose Bar Roller 9056M Socket Head Screw, M5 x 6 mm 9059M Low Head Socket Head Screw, M5 x 6 mm 9069M Socket Head Screw, M6 x mm 905M Flat Head Screw, M5 x mm 5 N-WW Nosebar Roller Kit (Includes Items 8 and 0) WW = Conveyor width reference: 0, 0, 06, 08,, 8 & Dorner Mfg. Corp Rev. A

25 " (5mm) and " (05mm) Wide Frame Assembly Service Parts 00 Rack Gear,.5 PA x P 70 T-Slot Cover Consult Factory Frame Assembly 709 Cam Mounting Assembly for Conveyors with Tracking Cams Rev. A 5 Dorner Mfg. Corp.

26 Service Parts 8" (57mm) and " (60mm) Wide Frame Assembly 00 Rack Gear.5 PA x P 70 T-Slot Cover 709 Cam Mounting Assembly for Conveyors with Tracking Cams Consult Factory Frame Assembly Dorner Mfg. Corp Rev. A

27 -0 (76 mm) Aluminum Side Service Parts For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart 00 Guide (76mm) HS Below Self-Drilling Hex Head Screw, /-0x Item : 00 Guide (76mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) Item : 00 Guide (76mm) HS Length End Guide (5mm) Left Hand (x) Right Hand (x) (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory Rev. A 7 Dorner Mfg. Corp.

28 Service Parts (8mm) Aluminum Side For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart Below 00 Guide (76mm) HS Self-Drilling Hex Head Screw, /-0x Item : 00 Guide 0.5 (mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Item : 00 Guide 0.5 (mm) HS Length End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory. Dorner Mfg. Corp Rev. A

29 -07 Low to Side Wiper Service Parts For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart Below 00 Guide (76mm) HS -00- Side Wiper Nylatron (per foot) Self-Drilling Hex Head Screw, /-0x Item : 00 Guide 0.5 (mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Item : 00 Guide 0.5 (mm) HS Length End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory Rev. A 9 Dorner Mfg. Corp.

30 Service Parts -09 Low to High Side For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart Below 00 Guide (76mm) HS Self-Drilling Hex Head Screw, /-0x Item : 00 Guide 0.5 (mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Item : 00 Guide 0.5 (mm) HS Length End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory. Dorner Mfg. Corp Rev. A

31 -0.5 (mm) Extruded Plastic Service Parts For For Conveyors 8 Conveyors 00 Guide Retaining Clip 0005P Snap-On Guide (per foot) See Chart Below 00 Guide Self-Drilling Hex Head Screw, /-0x Item : 00 Guide 0.5 (mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Item : 00 Guide 0.5 (mm) HS Length End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory Rev. A Dorner Mfg. Corp.

32 Service Parts - Adjustable Guiding Aluminum Profile Guide (60mm) 098 Aluminum Profile Guide (9mm) 0985 Aluminum Profile Guide (9mm) 0986 Aluminum Profile Guide 5 (5mm) 0987 Aluminum Profile Guide 6 (89mm) 0988 Aluminum Profile Guide 7 (mm) 0989 Aluminum Profile Guide 8 (8mm) 0990 Aluminum Profile Guide 9 (7mm) 099 Aluminum Profile Guide 0 (08mm) 099 Aluminum Profile Guide (5mm) 099 Aluminum Profile Guide (658mm) 099 Aluminum Profile Guide (96mm) 000 Mounting Bracket 007M Guide Mounting Shaft Vertical 008M Guide Mounting Shaft Horizontal MP Square Nut Cross Block Vinyl Shaft Cap P Flat Extruded Guide (per foot) Self-Drilling Hex Head Screw, /-0x M Socket Head Screw M6 x 6mm Dorner Mfg. Corp Rev. A

33 - Tool-Less Adjustable Guiding Service Parts Shaft Cap Cross Block 000M Mounting Bracket 007M Vertical Mounting Guide Shaft 5 008M Horizontal Mounting Guide Shaft MP Square Nut, M Self-Drilling Hex Head Screw, /-0x M Socket Head Screw, M6-.00 x 6 mm LLLLL Aluminum Profile Guide P-LLLLL Extruded Guide LLLLL = Length in inches with decimal places. Length Example: Length = 95.5" LLLLL = Rev. A Dorner Mfg. Corp.

34 Service Parts 0.5 (mm) Cleated Belt Guiding For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart 00 Guide, 0.7 (mm) Cleated Below Self-Drilling Hex Head Screw, /-0x Item : 00 Guide 0.5 (mm) HS Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) (658mm) Left Hand (x) Right Hand (x) Item : 00 Guide 0.5 (mm) HS Length End Guide (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory. Dorner Mfg. Corp Rev. A

35 (5mm) Cleated Belt Guiding Service Parts For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart Below 00 Guide (5mm) Cleated Self-Drilling Hex Head Screw, /-0x Item : 00 Guide Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Length Item : 00 Guide End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory Rev. A 5 Dorner Mfg. Corp.

36 Service Parts (5mm) Cleated Belt Guiding For 8 Conveyors For 9 6 Conveyor s 00 Guide Retaining Clip See Chart Below 00 Guide. Cleated Self-Drilling Hex Head Screw, /-0x Item : 00 Guide Length End Guide (60mm) Left Hand Right Hand (9mm) Left Hand Right Hand (9mm) Left Hand Right Hand (5mm) Left Hand Right Hand (89mm) Left Hand Right Hand (mm) Left Hand Right Hand (8mm) Left Hand Right Hand (7mm) Left Hand (x) Right Hand (x) 0 (08mm) Left Hand (x) Right Hand (x) (5mm) Left Hand (x) Right Hand (x) Length Item : 00 Guide End Guide (658mm) Left Hand (x) Right Hand (x) (96mm) Left Hand (x) Right Hand (x) (67mm) Left Hand (x) Right Hand (x) 5 (57mm) Left Hand (x) Right Hand (x) 6 (877mm) Left Hand (x) Right Hand (x) For conveyor lengths between even foot increments or longer than 6 (877 mm) consult factory. Dorner Mfg. Corp Rev. A

37 Flared Side Guiding Service Parts Guide Retaining Clip 0 Side-Flare Mounting Guide (60mm) 0 Side-Flare Mounting Guide (9mm) 0 Side-Flare Mounting Guide (9mm) 05 Side-Flare Mounting Guide 5 (5mm) 06 Side-Flare Mounting Guide 6 (89mm) 05M Flared Guide 5 (60mm) 05M Flared Guide 5 (9mm) 05M Flared Guide 5 (9mm) 05M Flared Guide 5 5 (5mm) 05M Flared Guide 5 6 (89mm) 90506M Button Head Screw M5 x 6mm Washer Self-Drilling Hex Head Screw, /-0x Rev. A 7 Dorner Mfg. Corp.

38 Service Parts Flat Belt Stand Mount Assembly Stand Mount 60579P Washer Square Nut M6 9060M Socket Head Screw M6 x 0mm Self-Drilling Hex Head Screw, /-0x Flat Belt Stand Mount Assembly Cleated Belt Stand Mount Assembly Cleated Mount Assembly 60579P Washer Square Nut M6 9060M Socket Head Screw M6 x 0mm Self-Drilling Hex Head Screw, /-0x Cleated Stand Mount Assembly Dorner Mfg. Corp Rev. A

39 Flat Belt Stand Mount Assembly for (60mm) Long Conveyors Service Parts Stand Mount, LH (60mm) 08 Stand Mount, RH (60mm) 60579P Washer Square Nut M M Socket Head Screw M6 x 0mm Self-Drilling Hex Head Screw, /-0x Flat Belt Stand Mount Assembly, for Idler End up to (60mm) Conveyors 756-DR Flat Belt Stand Mount Assembly, for Drive End up to (60mm) Conveyors Cleated Belt Stand Mount Assembly for (60mm) Long Conveyors Cleated Stand Bracket Assembly LH (60mm) Conveyor 085 Cleated Stand Bracket Assembly RH (60mm) Conveyor 60579P Washer Square Nut M M Socket Head Screw M6 x 0mm Self-Drilling Hex Head Screw, /-0x Cleated Belt Stand Mount Assembly for Idler end up to (60mm) Conveyors 7567-DR Cleated Belt Stand Mount Assembly for Drive End up to (60mm) Conveyors Rev. A 9 Dorner Mfg. Corp.

40 Service Parts Connecting Assembly without Stand Mount 70 Frame Connector Bar 0859 Frame Connector Plate 9069M Socket Low Head Screw M6xmm 756 Connecting Assembly without Stand Mounts Flat Belt Connecting Assembly with Stand Mount Stand Mount Square Nut M6 5mm x 0mm 60579P Washer 70 Frame Connector Bar M Socket Head Screw M6 x 0mm M Socket Low Head Screw M6xmm Flat Belt Connecting Assembly with Stand Mounts Dorner Mfg. Corp Rev. A

41 Cleated Belt Connecting Assembly with Stand Mount Service Parts Cleated Stand Bracket Square Nut M6 5mm x 0mm 60579P Washer 70 Frame Connector Bar M Socket Head Screw M6 x 0mm M Socket Low Head Screw M6 x 6mm Cleated Belt Connecting Assembly with Stand Mounts (5mm) to 6 (5mm) Flat Belt Return Roller Return Roller Guard - Short 087 Return Roller Clip Bearing 9-00 Dowel Pin M Socket Low Head Screw M6 x 6mm Roller Assembly (Includes Items, and ) (5mm) to 6 (5mm) Flat Belt Return Roller Assembly Rev. A Dorner Mfg. Corp.

42 Service Parts 8 (0mm) to (60mm) Flat Belt Return Roller Return Roller 087 Return Roller Clip 09WW Return Roller Guard 0WW Return Roller Rod M Socket Low Head Screw M6 x 6mm 6 08WW 8 (0mm) to (60mm) Flat Belt Return Roller Assembly WW = Conveyor width reference: 08,, 8 & Cleated Belt Return Roller Return Roller Guard - Short 088 Cleated Return Roller Clip Bearing 9-00 Dowel Pin M Socket Low Head Screw M6 x 6mm Roller Assembly (Includes Items, and ) 7 08 Cleated Belt Return Roller Assembly Dorner Mfg. Corp Rev. A

43 Conveyor Belt Part Number Configuration Figure 5 Service Parts 0F M WW -LLLL G D T S PA PD BB CF M WW -LLLL G D T S PP C L SSSS DORNER MFG. CORP HARTLAND, WI USA SERIAL # MODEL # Figure 5 Flat Belt Part Number Configuration Refer to Dorner patent plate (Figure 5). From the model number, determine conveyor width ( WW ), length ( LLLL ) and belt type ( BB ). Use data to configure belt part number as indicated below. *Add V for V-guided belts. - WW LLLL / BB V* Cleated Belt Part Number Configuration Refer to Dorner patent plate (Figure 5). From the model number, determine conveyor type ( T ), width ( WW ), length ( LLLL ), cleat type ( C ) and cleat spacing ( SSSS ). Use data to configure belt part number as indicated below. *Add V for V-guided belts. T - WW LLLL C SSSS V* / V* (Fill In) / V* (Fill In) Rev. A Dorner Mfg. Corp.

44 Return Policy Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without authorization will not be credited nor returned to the original sender. When calling for authorization, please have the following information ready for the Dorner factory representative or your local distributor:. Name and address of customer.. Dorner part number(s) of item(s) being returned.. Reason for return.. Customer's original order number used when ordering the item(s). 5. Dorner or distributor invoice number (if available, part serial number). A representative will discuss action to be taken on the returned items and provide a Returned Goods Authorization (RMA) number for reference. RMA will automatically close 0 days after being issued. To get credit, items must be new and undamaged. There will be a return charge on all items returned for credit, where Dorner was not at fault. It is the customer s responsibility to prevent damage during return shipping. Damaged or modified items will not be accepted. The customer is responsible for return freight. Conveyors and conveyor accessories Standard catalog conveyors 0% MPB, 700, 700 Series, cleated and specialty belt 50% AquaGard & AquaPruf Series conveyors non-returnable items Engineered to order products case by case Drives and accessories 0% Sanitary stand supports non-returnable items Parts Standard stock parts 0% Plastic chain, cleated and specialty belts non-returnable items Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning, disassembly, disposal and reissuing of components to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete. Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer Service Team will gladly help with your questions on Dorner products. For a copy of Dorner's Warranty, contact factory, distributor, service center or visit our website at For replacement parts, contact an authorized Dorner Service Center or the factory. Dorner Mfg. Corp. reserves the right to change or discontinue products without notice. All products and services are covered in accordance with our standard warranty. All rights reserved. Dorner Mfg. Corp. 0 DORNER MFG. CORP. 975 Cottonwood Ave., PO Box 0 Hartland, WI USA TEL (USA) FAX (USA) Internet: Outside the USA: TEL FAX Rev. A Printed in U.S.A.