READ THIS FIRST. Phone #: (360) Tech Support: Web:

Transcription

1 READ THIS FIRST Model W1742/W1742S ***IMPORTANT UPDATE*** Applies to Models Mfd. Since 09/17 and Owner's Manuals Printed 01/06 Phone #: (360) Tech Support: Web: We made the following change to these machines since the owner's manuals were printed: Changed outfeed roller from serrated steel to rubber. Aside from the information contained in this update, all other content in the owner's manual is applicable and MUST be read and understood for your own safety. IMPORTANT: Keep this update with the owner's manual for future reference. If you have any further questions, contact our Technical Support. V2 Outfeed Roller V1 & V2 Outfeed Roller Photos V1 163V2 (W1742, W1742S) V2 REF PART # DESCRIPTION 163V2 X V2 OUTFEED ROLLER (RUBBER) V (W1742) 163V2 X1742S163V2 OUTFEED ROLLER (RUBBER) V (W1742S) #19143BL COPYRIGHT AUGUST, 2017 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China

2 READ THIS FIRST Model W1742S ***IMPORTANT UPDATE*** Applies to Models Mfd. Since 04/15 and Manual Insert Revised 09/10 Phone #: (360) Tech Support: Web: We made the following changes to this machine since the manual insert was printed: Changed spiral cutterhead and indexable inserts. Aside from the information contained in this update, all other content in the owner's manual is applicable and MUST be read and understood for your own safety. IMPORTANT: Keep this update with the owner's manual for future reference. If you have any further questions, contact our Technical Support. Revised Parts V V2 150 REF PART # DESCRIPTION 143V2 X1742S143V2 INDEXABLE INSERT 14 X 14 X 2 V V2 X1742S148V2 SPIRAL CUTTERHEAD V #17659BL COPYRIGHT SEPTEMBER, 2015 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China

3 READ THIS FIRST Model W1742/W1742S ***IMPORTANT UPDATE*** Applies to Models Mfg. Since 7/12 and Owner's Manual January, 2006 Phone #: (360) Tech Support: Web: The following changes were recently made to these machines since the owner's manual was printed: Now certified to meet CSA 22.2 # and UL 987-7th standards. Changed the motor nominal voltage from 220V to 240V and added a power cord with a plug. This document provides relevant updates to portions of the owner's manual that no longer apply and additional information required by CSA aside from this information, all other content in the owner's manual applies and MUST be read and understood for your own safety. IMPORTANT: Keep this update with the owner's manual for future reference. If you have any further questions, contact our Technical Support. Changed Specifications Electrical Power Requirement...240V, Single-Phase, 60 Hz Motor Voltage V Amps... 15A Operation Info Cutterhead Speed RPM New/Revised Parts REF PART # DESCRIPTION REF PART # DESCRIPTION 30A X A MOTOR 3HP 240V 1-PH V A-9 X A-9 CENTRIFUGAL SWITCH 16MM A-1 X A-1 MOTOR FAN COVER V A-10 X A-10 CONTACT PLATE 16MM 30A-2 X A-2 MOTOR FAN V V2-1 X CONTACTOR NHD C-09D 230V 30A-4 X A-4 R CAPACITOR 20M 400V 72V1-2 X V2-2 OL RELAY NHD NTH A 30A-5 X A-5 S CAPACITOR 200M 250V 3-7/8 X 1-1/2 74V2 X V2 PWR CORD 12G 3W 72" 6-20P V A-6 X MOTOR JUNCTION BOX 503V2 X V2 ID LABEL CSA V (W1742) 30A-7 XP6204ZZ BALL BEARING 6204ZZ 503V2 X1742S503V2 ID LABEL CSA V (W1742S) 30A-8 XP6203ZZ BALL BEARING 6203ZZ COPYRIGHT AUGUST, 2012 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. #15241BLTS Printed in China

4 SAFETY Model W1742/W1742S (Mfg. Since 7/12) For Your Own Safety, Read Manual Before Operating Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures this responsibility is ultimately up to the operator! Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. NOTICE This symbol is used to alert the user to useful information about proper operation of the equipment or a situation that may cause damage to the machinery. Standard Machinery Safety Instructions OWNER S MANUAL. Read and understand this owner s manual BEFORE using machine. TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed. Only allow trained/supervised people to use this machine. When machine is not being used, disconnect power, remove switch keys, or lock-out machine to prevent unauthorized use especially around children. Make workshop kid proof! DANGEROUS ENVIRONMENTS. Do not use machinery in areas that are wet, cluttered, or have poor lighting. Operating machinery in these areas greatly increases the risk of accidents and injury. MENTAL ALERTNESS REQUIRED. Full mental alertness is required for safe operation of machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted. ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow an electrician or qualified service personnel to do electrical installation or repair work, and always disconnect power before accessing or exposing electrical equipment. DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making adjustments, changing tooling, or servicing machine. This eliminates the risk of injury from unintended startup or contact with live electrical components. EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses. -2-

5 Model W1742/W1742S (Mfg. Since 7/12) WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. HAZARDOUS DUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk. HEARING PROTECTION. Always wear hearing protection when operating or observing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss. REMOVE ADJUSTING TOOLS. Tools left on machinery can become dangerous projectiles upon startup. Never leave chuck keys, wrenches, or any other tools on machine. Always verify removal before starting! INTENDED USAGE. Only use machine for its intended purpose and never make modifications not approved by Woodstock. Modifying machine or using it differently than intended may result in malfunction or mechanical failure that can lead to serious personal injury or death! AWKWARD POSITIONS. Keep proper footing and balance at all times when operating machine. Do not overreach! Avoid awkward hand positions that make workpiece control difficult or increase the risk of accidental injury. CHILDREN & BYSTANDERS. Keep children and bystanders at a safe distance from the work area. Stop using machine if they become a distraction. GUARDS & COVERS. Guards and covers reduce accidental contact with moving parts or flying debris make sure they are properly installed, undamaged, and working correctly. FORCING MACHINERY. Do not force machine. It will do the job safer and better at the rate for which it was designed. NEVER STAND ON MACHINE. Serious injury may occur if machine is tipped or if the cutting tool is unintentionally contacted. STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or loss of control. Before starting, verify machine is stable and mobile base (if used) is locked. USE RECOMMENDED ACCESSORIES. Consult this owner s manual or the manufacturer for recommended accessories. Using improper accessories will increase risk of serious injury. UNATTENDED OPERATION. To reduce the risk of accidental injury, turn machine OFF and ensure all moving parts completely stop before walking away. Never leave machine running while unattended. MAINTAIN WITH CARE. Follow all maintenance instructions and lubrication schedules to keep machine in good working condition. A machine that is improperly maintained could malfunction, leading to serious personal injury or death. CHECK DAMAGED PARTS. Regularly inspect machine for any condition that may affect safe operation. Immediately repair or replace damaged or mis-adjusted parts before operating machine. MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab and pull the plug NOT the cord. Pulling the cord may damage the wires inside, resulting in a short. Do not handle cord/plug with wet hands. Avoid cord damage by keeping it away from heated surfaces, high traffic areas, harsh chemicals, and wet/damp locations. EXPERIENCING DIFFICULTIES. If at any time you experience difficulties performing the intended operation, stop using the machine! Contact Technical Support at (360)

6 Additional Safety for Planers PLANER INJURY RISKS. Familiarize yourself with the main injury risks associated with planers always use common sense and good judgement to reduce your risk of injury. Main injury risks from planers: amputation/lacerations from contact with the moving cutterhead, entanglement/crushing injuries from getting caught in moving parts, blindness or eye injury from flying wood chips, or impact injuries from workpiece kickback. KICKBACK. Know how to reduce the risk of kickback and kickback-related injuries. Kickback occurs during the operation when the workpiece is ejected from the machine at a high rate of speed. Kickback is commonly caused by poor workpiece selection, unsafe feeding techniques, or improper machine setup/maintenance. Kickback injuries typically occur as follows: (1) operator/bystanders are struck by the workpiece, resulting in impact injuries (i.e., blindness, broken bones, bruises, death); (2) operator s hands are pulled into blade, resulting in amputation or severe lacerations. REACHING INSIDE PLANER. Never remove guards/covers or reach inside the planer during operation or while connected to power. You could be seriously injured if you accidentally touch the spinning cutterhead or get entangled in moving parts. If a workpiece becomes stuck or sawdust removal is necessary, turn planer OFF and disconnect power before clearing. DULL/DAMAGED KNIVES/INSERTS. Only use sharp, undamaged knives/inserts. Dull or damaged knives/inserts increase the risk of kickback. INSPECTING STOCK. To reduce the risk of kickback injuries or machine damage, thoroughly inspect and prepare the workpiece before cutting. Verify workpiece is free of nails, staples, loose knots or foreign material. Workpieces with minor warping should be jointed first or planed with the cupped side facing the infeed table. -4- Model W1742/W1742S (Mfg. Since 7/12) BODY PLACEMENT. Stand to one side of planer during the entire operation to avoid getting hit if kickback occurs. GRAIN DIRECTION. Planing across the grain is hard on the planer and may cause kickback. Plane in the same direction or at a slight angle with the wood grain. PLANING CORRECT MATERIAL. Only plane natural wood stock. DO NOT plane MDF, OSB, plywood, laminates or other synthetic materials that can break up inside the planer and be ejected towards the operator. LOOKING INSIDE PLANER. Wood chips fly around inside planer at a high rate of speed during operation. To avoid injury from flying material, DO NOT look inside planer during operation. CUTTING LIMITATIONS. To reduce risk of kickback hazards or damage to machine, do not exceed maximum depth of cut or minimum board length and thickness found in Data Sheet. Only feed one board at a time. INFEED ROLLER CLEARANCE. The infeed roller is designed to pull material into the spinning cutterhead. To reduce the risk of entanglement, keep hands, clothing, jewelry, and long hair away from the infeed roller during operation. FEED WORKPIECE PROPERLY. To reduce the risk of kickback, never start planer with workpiece touching cutterhead. Allow cutterhead to reach full speed before feeding, and do not change feed speed during cutting operation. WORKPIECE SUPPORT. To reduce risk of kickback, always make sure workpiece can move completely across table without rocking or tipping. Use auxiliary support stands for long stock. SECURE KNIVES/INSERTS. Loose knives or improperly set inserts can become dangerous projectles or cause machine damage. Always verify knives/inserts are secure and properly adjusted before operation.

7 Model W1742/W1742S (Mfg. Since 7/12) ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power. A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power supply circuit used for this machine must be sized to safely handle the fullload current drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.) The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so later in this manual. Full-Load Current Rating The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations. Full-Load Current Rating at 240V Amps Circuit Requirements This machine is prewired to operate on a 240V power supply circuit that has a verified ground and meets the following requirements: Circuit Type V, 60 Hz, Single-Phase Circuit Size Amps Plug/Receptacle... NEMA 6-20 Incorrectly wiring or grounding this machine can cause electrocution, fire, or machine damage. To reduce this risk, only an electrician or qualified service personnel should do any required electrical work on this machine. NOTICE The circuit requirements listed in this manual apply to a dedicated circuit where only one machine will be running at a time. If this machine will be connected to a shared circuit where multiple machines will be running at the same time, consult with an electrician to ensure that the circuit is properly sized for safe operation. -5-

8 Model W1742/W1742S (Mfg. Since 7/12) Grounding Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipmentgrounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipmentgrounding wire to a live (current carrying) terminal. Check with a qualified electrician or service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one. For 240V Connection This machine is equipped with a power cord that has an equipment-grounding wire and NEMA 6-20 grounding plug. The plug must only be inserted into a matching receptacle (see Figure) that is properly installed and grounded in accordance with local codes and ordinances. The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so later in this manual. Current Carrying Prongs 6-20 PLUG GROUNDED 6-20 RECEPTACLE Grounding Prong Figure 2. NEMA 6-20 plug & receptacle. Extension Cords We do not recommend using an extension cord with this machine. Extension cords cause voltage drop, which may damage electrical components and shorten motor life. Voltage drop increases with longer extension cords and the gauge smaller gauge sizes (higher gauge numbers indicate smaller sizes). No adapter should be used with the required plug. If the plug does not fit the available receptacle or the machine must be reconnected to a different type of circuit, the reconnection must be made by an electrician or qualified service personnel and it must comply with all local codes and ordinances. Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following requirements: Minimum Gauge Size at 240V AWG Maximum Length (Shorter is Better)...50 ft. -6-

9 Model W1742/W1742S (Mfg. Since 7/12) Wiring Diagram CONTROL PANEL (from Behind) 6-20 Plug 240V MAGNETIC SWITCH ASSY MOTOR (240V, Single-Phase) -7-

10

11 Cabinet Breakdown W1742S 15" Planer with Spiral Cutterhead -4-

12 W1742S 15" Planer with Spiral Cutterhead Cabinet Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 X RUBBER FEET 39 X COLLAR 2 X STRAIN RELIEF 41 X PLATE CONNECTING ROD 3 X UNIVERSAL PULLEY 42 XPSS04M SET SCREW M6-1 X 12 4 XPN03M HEX NUT M X MOTOR PLATE 5 XPW01M FLAT WASHER 8MM 44 XPFH06M FLAT HD SCR M6-1 X 20 6 XPB86M HEX BOLT M X X COVER 7 X SLEEVE 46 X ENCLOSED STAND 8 XPR16M EXT RETAINING RING 9MM 47 XPB144M HEX BOLT M X 55 9 XPW06M FLAT WASHER 12MM 48 XPW04M FLAT WASHER 10MM 10 X SHAFT 12MM 49 XPN02M HEX NUT M X PEDAL 50 X BUSHING 12 XPN03M HEX NUT M X PLATE CONNECTING ROD ASSY 13 XPB45M HEX BOLT M X XPW04M FLAT WASHER 10MM 14 XPW01M FLAT WASHER 8MM 53 XPN02M HEX NUT M XPB22M HEX BOLT M X XPB44M HEX BOLT M X X BRACKET 55 XPSS14M SET SCREW M X XPR21M INT RETAINING RING 35MM 56 XPK12M KEY 5 X 5 X XP6202 BALL BEARING XPB09M HEX BOLT M X X TROLLEY WHEEL 58 XPB83M HEX BOLT M6-1 X X SLEEVE 59 X BALL STRAIN RELIEF 21 XPLN09 LOCK NUT M X CONTROL BOX 22 XPW06M FLAT WASHER 12MM 61 X SUPPORT ARM 23 X SPECIAL BOLT 62 XPHTEK6 TAP SCREW #10 X 3/8 24 X TROLLEY UNIVERSAL KIT 63 X CONTROL PANEL 25 XPB118M HEX BOLT M X X EMERGENCY STOP BUTTON 26 XPN03M HEX NUT M X POWER LAMP 27 XPW01M FLAT WASHER 8MM 66 X ON BUTTON 30 X MOTOR 3HP 220V 67 X HEX NUT M X MOTOR FAN COVER 68 XPW02M FLAT WASHER 5MM 30-2 X MOTOR FAN 69 X PLATE 30-3 X CAPACITOR COVER 70 XPB17M HEX BOLT M6-1X X RUN CAPACITOR 20UF 250VAC 71 XPW03M FLAT WASHER 6MM 30-5 X START CAPACITOR 500UF 125VAC 72 X MAGNETIC SWITCH ASSY 30-6 X JUNCTION BOX 72-1 X SWITCH BOX BACK COVER 35 XPW06M FLAT WASHER 12MM 72-2 X CONTACTOR NHD C35-D 220V 36 XPN09M HEX NUT M X OL RELAY NHD NTH X ADJUST BOLT 72-4 X SWITCH BOX FRONT COVER 38 XPSS03M SET SCREW M6-1 X 8 73 XPS22M PHLP HD SCREW M5-.8 X 25-5-

13 -6- W1742S 15" Planer with Spiral Cutterhead Headstock Breakdown

14 W1742S 15" Planer with Spiral Cutterhead Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 101 X HANDLE 150 XP6205 BALL BEARING XPN09M HEX NUT M XPB83M HEX BOLT M6-1 X XPW06M FLAT WASHER 12MM 152 XPW03M FLAT WASHER 6MM 105 X HANDWHEEL 153 X SPROCKET 106 X COLLAR 154 X SCALE 107 XPR29M INT RETAINIING RING 32MM 155 XPW03M FLAT WASHER 6MM 108 XP6201 BALL BEARING XPS14M PHLP HD SCR M6-1 X XPK48M KEY 4 X 4 X X POINTER 110 X WORM GEAR 158 XPW03M FLAT WASHER 6MM 111 X WORM HOUSING 159 XPS14M PHLP HD SCR M6-1 X X CAP SCREW M5-0.8 X X CUT LIMIT PLATE 113 X ROLLER 161 XPS03M PHLP HD SCR M6-1 X X ROLLER STAND 162 X HEAD CASTING 115 PSB155M CAP SCREW M X X OUTFEED ROLLER 116 X BELT COVER 164 XPK08M KEY 5 X 5 X X FEMALE KNOB M X COMPRESSION SPRING 118 XPFH02M FLAT HD SCR M6-1 X X SPECIAL SET SCREW 119 X DUST HOOD 167 X BUSHING 120 XPSB14M CAP SCREW M X X PLATE XPW01M FLAT WASHER 8MM 169 XPB03M HEX BOLT M X XPB04M HEX BOLT M6-1 X XPSS53M SET SCREW M5-.8 X XPN01M HEX NUT M XPN06M HEX NUT M XPW03M FLAT WASHER 6MM 172 X SHAFT 124 X UPPER COVER 173 XPSS25M SET SCREW M6-1 X XPFB01M FLANGE BOLT M6-1 X X CHIP BREAKER 126 X FOAM 175 XPSS58M SET SCREW M6-1 X X GEAR BOX COVER 176 XPN01M HEX NUT M XPVMX60 V-BELT MX X RECEIVER PIN 129 XPSB45M CAP SCREW M X X LOCKING ROD 130 XPRP07M ROLL PIN 6 X XPR03M EXT RETAINING RING 12MM 131 X SAFETY HATCH 180 XPLW05M LOCK WASHER 12MM 132 XPFB09M FLANGE BOLT M6-1 X XPN09M HEX NUT M X IDLE BRACKET ASSY 182 XPEC05M E-CLIP 15MM X BRACKET 183 X COLLAR X IDLE PULLEY 184 X ANTI-KICKBACK FINGER X IDLE SHAFT 185 X SHAFT 134 X SHAFT 186 XPSS06M SET SCREW M X X COLLAR 187 XPB83M HEX BOLT M6-1 X X EXTENSION SPRING 188 XPW03M FLAT WASHER 6MM 137 X HANGER 189 X SPROCKET 138 XPSB68M CAP SCREW M6-1 X X CHAIN 06B-1 X X CHIP DEFLECTOR PLATE 191 XPK08M KEY 5 X 5 X XPFB01M FLANGE BOLT M6-1 X X INFEED ROLLER 141 X PRESS PLATE 193 XPW03M FLAT WASHER 6MM 142 XPFB01M FLANGE BOLT M6-1 X XPB02M HEX BOLT M6-1 X X1741S164 INDEXABLE INSERT 14 X 14 X X CUTTERHEAD PULLEY 145 XPFH35M FLAT HD TORX SCR T20 M6-1 X X MOTOR PULLEY 146 X1741S227 DRIVER BIT TORX T X COLLAR 147 X1741S228 L-WRENCH TORX T XPB09M HEX BOLT M X X1742S148 SPIRAL CUTTERHEAD 199 X BELT GUARD 149 XPK129M KEY 8 X 8 X 36-7-

15 Gearbox Breakdown W1742S 15" Planer with Spiral Cutterhead REF PART # DESCRIPTION REF PART # DESCRIPTION 201 X GEAR BOX 222 XPW03M FLAT WASHER 6MM 202 XPB10M HEX BOLT M6-1 X X COMPRESSION SPRING 203 X SPROCKET 224 X STEEL BALL 4MM 204 XPW01M FLAT WASHER 8MM 225 X GEAR 205 XPB03M HEX BOLT M X XPK36M KEY 5 X 5 X X CHAIN 06B-1 X X GASKET 207 X FEMALE KNOB M X GEAR BOX COVER 208 X SHAFT 229 XPB22M HEX BOLT M X XP6201 BALL BEARING X OIL PLUG 210 X GEAR 231 X FLANGE COVER 211 XPK19M KEY 5 X 5 X XPSB33M CAP SCREW M5-.8 X X SHAFT 233 X OIL SEAL 25 X 40 X XP6201 BALL BEARING XPRP35M PIN 5 X X GEAR 235 X SHIFT FORK 215 XPK06M KEY 5 X 5 X X HANDLE SHAFT 216 X OIL SEAL 25 X 32 X X X O-RING 16 X X SHAFT 238 XPFB01M FLANGE BOLT M6-1 X XP6204 BALL BEARING XPK08M KEY 5 X 5 X XPR09M EXT RETAINING RING 20MM 240 XP6204 BALL BEARING XP6201 BALL BEARING X GEAR 221 XPS03M PHLP HD SCR M6-1 X XPSS25M SET SCREW M6-1 X 20-8-

16 W1742S 15" Planer with Spiral Cutterhead Columns Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 301 X CHAIN 12.7 AX X GEAR 302 XPB24M HEX BOLT M X XPK69M KEY 4 X 4 X XPW06M FLAT WASHER 12MM 318 XPR03M EXT RETAINING RING 12MM 304 X LIFTING BAR 319 X SPROCKET 305 X COLUMN 320 XPK08M KEY 5 X 5 X P6302 BALL BEARING XPW04M FLAT WASHER 10MM 307 XPR24M INT RETAINING RING 42MM 322 XPN02M HEX NUT M X COLUMN 323 X BRACKET 309 X SPROCKET 324 XPR05M EXT RETAINING RING 15MM 310 XPSS13M SET SCREW M X XPW01M FLAT WASHER 8MM 311 X LEAD SCREW 326 XPB09M HEX BOLT M X X LEAD SCREW 327 XPR23M INT RETAINING RING 40MM 313 X LEAD NUT 328 XPN09M HEX NUT M XPSB02M CAP SCREW M6-1 X XPR05M EXT RETAINING RING 15MM 315 X BUSHING 333 X BASE -9-

17 Table Breakdown W1742S 15" Planer with Spiral Cutterhead REF PART # DESCRIPTION REF PART # DESCRIPTION 401 XPSS09M SET SCREW M X X GIB 404 XPB26M HEX BOLT M X X LOCK BAR 405 XPW01M FLAT WASHER 8MM 412 XPSS11M SET SCREW M6-1 X XPLW04M LOCK WASHER 8MM 413 X ECCENTRIC SHAFT 407 X EXTENSION WING 414 XP6203 BALL BEARING X FEMALE KNOB M X ROLLER 409 X WEDGE DOG 416 X TABLE/BED -10-

18 W1742S 15" Planer with Spiral Cutterhead Labels & Cosmetics Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Woodstock International, Inc. at (360) or to order new labels. REF PART # DESCRIPTION REF PART # DESCRIPTION 500 X SHOP FOX LOGO PLATE 507 XLABEL-04S ELECTRICTY LABEL 501 X LOCK BASE LABEL 508 XLABEL-06 RESPIRATOR/GLASSES LABEL 502 X SHIFT GEARS LABEL 509 XLABEL-02 UNPLUG LABEL 503 X1742S503 MACHINE ID LABEL 510 X PINSTRIPE TAPE 504 XLABEL-03S KEEP CLOSED LABEL 511 X OIL HERE LABEL 505 X1742S505 W1742S LABEL 512 X ROTATION LABEL 506 XLABEL-08 READ MANUAL LABEL -11-