SECTION 9: PARTS Fence & Cutterhead

Transcription

1 (G0855 Only) (G0856 Only) SECTION 9: PARTS Fence & Cutterhead (G0856 Only) (G0855 Only) Model G0855/G0856 (Mfd. Since 07/18) -57-

2 104 Tables, Base, Stand & Motor Model G0855/G0856 (Mfd. Since 07/18)

3 Parts List 1 P FENCE TILT LOCK LEVER 1/ P SHAFT W/HOLE 2-3/4L 2 P FLAT WASHER 13MM 51 P ROLL PIN 3 X 20 3 P STOP BLOCK 52 P COMPRESSION SPRING 4 P FENCE CARRIAGE 53 P SPRING SLEEVE 5 P KNOB 3/8-16, D1-5/16, BALL 54 P CAP SCREW 3/8-16 X 1-1/4 6 P ECCENTRIC SHAFT 3/8-16, 5-1/4L 55 P CAP SCREW 5/16-18 X 3/4 7 P DOWEL PIN 5 X P ADJUSTABLE HANDLE 2L, 1/4-20 X 1 8 P CAP SCREW 1/4-20 X 1-1/4 57 P KNOB 1/4-20, D7/8, BALL 9 P HEX NUT 1/ P SET SCR 5/16-18 X 3/4, 1-5/16, SLOTTED 10 P SHOULDER BOLT 5/16-18 X 11/16, 3/8 X 1 59 P FOLDING HANDLE 2-1/4L, 5/16-18 X 1-3/16 11 P HEX NUT 1/2-20 THIN 60 P SCALE POINTER 12 P FENCE 61 P FLAT WASHER 4MM 13 P STUD-SE 1/2-20, 1-3/8, 11/16 62 P PHLP HD SCR 8/32 X 1/4 14 P HEX NUT 5/ P PHLP HD SCR 1/4-20 X 1/2 15 P HEX BOLT 5/16-18 X 1-1/4 64 P HEX BOLT 3/8-16 X 1 16 P FLAT HD CAP SCR 5/16-18 X 1-1/2 65 P ROLL PIN 4 X P FENDER WASHER 1/2 66 P SET SCREW 5/16-18 X 1/2 18 P FENCE LINK 67 P RABBETING TABLE 19 P T-NUT 1/ P BEARING BLOCK PLATE 20 P FENCE BLOCK 69 P LOCK WASHER 5/16 21 P FENCE SWIVEL BASE 70 P TABLE HANDWHEEL W/HANDLE 22 P SET SCR 3/8-16 X 1-1/2, CONE-PT, SLOTTED 71 P FENDER WASHER 8.5 X 23 X 2MM 23 P STUD-DE 3/8-16 X 3-1/8, 3/8 72 P PHLP HD SCR 5/16-18 X 1/2 24 P HEX NUT 3/8-16 THIN 73 P KNOB BOLT 5-LOBE 3/8-16 X 1, D1-3/4 25 P SAFETY PLATE 74 P LATCH 26 P HEX NUT 1/ P HEX NUT 3/ P CAMLOCK STUD 1/2-12 X 1-1/2, 3-1/2L 76 P DUST PORT 4" 28 P CAP SCREW 1/4-20 X 1/2 77 P PHLP HD SCR 1/4-20 X 1/2 29 P FLAT WASHER 1/4 78 P LOCK WASHER 10MM 30 P FENCE BASE 79 P STANDOFF HEX 3/8-16 X 3/4, 3-5/16L 31 P FLAT WASHER 3/8 80 P CABINET STAND 32 P ROLL PIN 4 X P REAR ACCESS PANEL 33 P KEY 9.5 X 9.5 X P FOAM PAD 34 P CAP SCREW 3/8-16 X 1-1/2 83 P V-BELT 350J-7 35" 35 P BEARING BLOCK 84 P FLAT WASHER 5/16 36 P BALL BEARING NSE 85 P HEX BOLT 5/16-18 X 3/4 37 P KEY 5 X 5 X P MOTOR 3HP 230V 1-PH 38 P SET SCREW M6-1 X P KEY 5 X 5 X P CUTTERHEAD PULLEY 86-3 P MOTOR PULLEY 40 P CUTTERHEAD 8" 4-KNIFE (P0855) 86-4 P SET SCREW M6-1 X P COMPRESSION SPRING (P0855) 86-5 P MOTOR LABEL 40-3 P FLAT HD CAP SCR M5-.8 X 12 (P0855) 86-6 P STRAIN RELIEF TYPE-3 PG P KNIFE 8 X 3/4 X 1/8 HSS (P0855) 86-7 P MOTOR CORD 14G 3W 32" 40-5 P KNIFE GIB (P0855) 86-8 P STRAIN RELIEF TYPE-1 3/4" 40-6 P KNIFE GIB BOLT 1/4-28 X 1/4 (P0855) 86-9 P BACKING BOARD 40 P SPIRAL CUTTERHEAD 8" (G0856) P MOTOR FAN COVER 40-2 P FLAT HD TORX SCR T X 1/2 (G0856) P MOTOR FAN 40-3 P CARBIDE INSERT 15 X 15 X 2.5MM (G0856) P CONTACT PLATE 41 P STUD-DE 3/8-24 X 4-3/4, 1/ P CENTRIFUGAL SWITCH 42 P HEX NUT 3/ P S CAPACITOR 400M 125V 1-1/2 X 3-1/2 43 P BELT COVER P R CAPACITOR 70M 250V 1-1/2 X 3-1/2 44 P KNOB 5/16-18, D1-3/4, ROUND P CAPACITOR COVER 45 P CUTTERHEAD GUARD P BALL BEARING 6205-ZZ (FRONT) 46 P STANDOFF-HEX MM 5/16-18 X 3/8, P BALL BEARING 6203-ZZ (REAR) 47 P SET SCREW 1/4-20 X 3/4 87 P WHEEL AXLE 3/8-16 X 1-3/16, 2-1/2L 48 P HEX NUT 1/ P WHEEL 49 P DEPTH STOP BLOCK 89 P LOCK NUT 3/8-16 Model G0855/G0856 (Mfd. Since 07/18) -59-

4 Parts List (Cont.) 90 P KNOB BOLT 6-LOBE 5/16-18 X 3/4 114 P TORSION SPRING 91 P MAG SWITCH KEDU KJD17B-230V-S 115 P ROLL PIN 6 X P CAP SCREW 1/2-12 X 1-3/4 116 P ROLL PIN 5 X P SET SCREW 1/4-20 X 1/4 117 P PUSH BLOCKS 94 P LOCK WASHER 8MM 118 P FLAT WASHER 12MM 95 P CAP SCREW M X P SWITCH BOX 96 P SWITCH PEDESTAL 120 P SWITCH PLATE 97 P CAP SCREW M X 20 W/WASHERS 121 P SWITCH CORD 14G 3W 20" 98 P LOCK WASHER 3/8 122 P POWER CORD 14G 3W 10' 6-20P 99 P LOCK WASHER 1/2 123 P TAP SCREW M6 X P KEY 5 X 5 X P ADJUSTABLE FOOT M P HEX NUT 5/ P HEX NUT M P TABLE BASE 126 P STRAIN RELIEF TYPE-1 5/8" 103 P INFEED TABLE 127 P PHLP HD SCR M4-.7 X P OUTFEED TABLE 128 P PHLP HD SCR M4-.7 X P LEADSCREW SUPPORT 129 P EXT TOOTH WASHER 4MM 106 P LEADSCREW BRACKET 130 P HEX WRENCH 3MM 107 P LEADSCREW 131 P HEX WRENCH 4MM 108 P LEADSCREW COLLAR 132 P HEX WRENCH 5MM 109 P TABLE GIB 133 P WRENCH 8 X 10 OPEN-ENDS 110 P SET SCREW 5/16-18 X 1-1/4 CONE-PT 134 P WRENCH 12 X 14 OPEN-ENDS 111 P KNIFE-SETTING JIG (P0855) 135 P WRENCH 11 X 13 OPEN-ENDS 111 P TORX DRIVER T-25 (G0856) 136 P HEX WRENCH 6MM 112 P GUARD PIVOT SHAFT 137 P GROUND LABEL 113 P EXT RETAINING RING 11MM -60- Model G0855/G0856 (Mfd. Since 07/18)

5 Labels & Cosmetics 202 To reduce risk of death or serious injury, read manual BEFORE using machine. To get a new manual, call (800) or go to Failure to keep hands clear of cutterhead will result in serious personal injury. Cutterhead exposed between these lines. Failure to keep hands clear of cutterhead will result in serious personal injury INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service. 207 DANGER! ROTATING CUTTERHEAD BELOW! Specifications Motor: 3 HP, 230V, Single-Phase, 60 Hz Full-Load Current: 12A Cutterhead: 4-Knife, 3-1/16" Dia. Knife Size: 8" x 3/4" x 1/8" Replacement Knives: H4982 Cutterhead Speed: 5500 RPM Cuts Per Minute: 22,000 Fence Tilt: 45º, 90º, 135º Table Size: 72" x 9" Min. Workpiece Length: 10" Min. Workpiece Thickness: 1/2" Max. Depth of Cut Per Pass: 1/8" Max. Rabbeting Depth: 1/2" Weight: 373 lbs. Mfd. for Grizzly in Taiwan Date S/N MODEL G0855 8" DOVETAIL JOINTER w/mobile BASE To reduce the risk of serious injury when using this machine: 1. Read and understand owner s manual before operating. 2. Always wear approved eye protection and respirator. 3. Only plug power cord into a grounded outlet. 4. Except when rabbeting, keep all guards in place and in proper operating condition. Always replace guard after rabbeting. 5. Never cut workpieces smaller than 10" long and 1/2" thick. 6. Always use push blocks when face planing. 7. Keep hands at least 4" away from cutterhead. 8. Never cut deeper than 1/8" on a single pass. 9. Be aware of "kickback" hazards and how to prevent them. 10. Turn motor OFF and disconnect power before changing blades, adjusting tables/fence, or servicing. 11. Tie back long hair, roll up sleeves, and DO NOT wear loose clothing, gloves, or jewelry. 12. Before starting, ensure tables are adjusted properly, blades are secure, and jointer is stable. 13. Do not joint boards with cracks, loose knots, or any defects. 14. DO NOT expose to rain or use in wet conditions. 15. Always support workpiece against fence and table when cutting. Never attempt any operation free-handed. 16. Always feed workpiece against cutterhead rotation. Never move workpiece backward while feeding. 17. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended. MODEL G0856 8" DOVETAIL JOINTER w/ SPIRAL CUTTERHEAD & MOBILE BASE Use this guard for all possible operations, and immediately reinstall it following operations that require its removal. INJURY HAZARD! To reduce risk of short and long-term injury, wear safety glasses, hearing protection, and a respirator when using this machine. 209 KICKBACK HAZARD! ALWAYS USE PUSH BLOCKS! 1. Ensure outfeed table is even with knives/inserts. 2. Never exceed the maximum depth of cut. 3. Do not stand directly behind workpiece. Push blocks minimize the possibility of operators hands contacting the cutterhead while cutting. Specifications Motor: 3 HP, 230V, Single-Phase, 60 Hz Full-Load Current: 12A Cutterhead: Spiral w/indexable Inserts Insert Size: 15 x 15 x 2.5mm Number of Inserts: 36 Replacement Inserts: H9893 Cutterhead Speed: 5500 RPM Cuts Per Minute: 22,000 Fence Tilt: 45º, 90º, 135º Table Size: 72" x 9" Min. Workpiece Length: 10" Min. Workpiece Thickness: 1/2" Max. Depth of Cut Per Pass: 1/8" Max. Rabbeting Depth: 1/2" Weight: 373 lbs. Mfd. for Grizzly in Taiwan Date S/N To reduce the risk of serious injury when using this machine: 1. Read and understand owner s manual before operating. 2. Always wear approved eye protection and respirator. 3. Only plug power cord into a grounded outlet. 4. Except when rabbeting, keep all guards in place and in proper operating condition. Always replace guard after rabbeting. 5. Never cut workpieces smaller than 10" long and 1/2" thick. 6. Always use push blocks when face planing. 7. Keep hands at least 4" away from cutterhead. 8. Never cut deeper than 1/8" on a single pass. 9. Be aware of "kickback" hazards and how to prevent them. 10. Turn motor OFF and disconnect power before changing inserts, adjusting tables/fence, or servicing. 11. Tie back long hair, roll up sleeves, and DO NOT wear loose clothing, gloves, or jewelry. 12. Before starting, ensure tables are adjusted properly, inserts are secure, and jointer is stable. 13. Do not joint boards with cracks, loose knots, or any defects. 14. DO NOT expose to rain or use in wet locations. 15. Always support workpiece against fence and table when cutting. Never attempt any operation free-handed. 16. Always feed workpiece against cutterhead rotation. Never move workpiece backward while feeding. 17. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended. 210 G0855 G grizzly.com INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service KEEP PANEL CLOSED WHILE OPERATING! 201 P MACHINE ID LABEL (G0855) 208 P EYES EARS LUNGS WARNING LABEL 201 P MACHINE ID LABEL (G0856) 209 P GRIZZLY NAMEPLATE-SMALL 202 P READ MANUAL LABEL 210 P MODEL NUMBER LABEL (G0855) 203 P CUTTERHEAD WARNING LABEL 210 P MODEL NUMBER LABEL (G0856) 204 P CUTTERHEAD EXPOSED LABEL 211 P GRIZZLY.COM LABEL 205 P ELECTRICITY LABEL 212 P PANEL CLOSED WARNING LABEL 206 P DISCONNECT POWER LABEL 213 P TOUCH-UP PAINT, GRIZZLY GREEN 207 P CUTTERHEAD GUARD LABEL 214 P TOUCH-UP PAINT, GREY PUTTY Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) or Model G0855/G0856 (Mfd. Since 07/18) -61-