Greenhouse Plans_Part Two Cutting & Assembly
|
|
- Jerome Flowers
- 5 years ago
- Views:
Transcription
1 Greenhouse Plans_Part Two Cutting & Assembly When I did drafting for a living, it wasn t a good idea to start out by announcing that I was going to make mistakes because that s a good way to not get the job. I had to do everything conventionally to look like engineering and architectural drawings with dimensions, title blocks, notes and all that
2 monkey business. But I m doing this for fun and I m not getting paid for it so I can be as folksy and artsy-fartsy as I want to be. Screw-up is the human condition.look at General Motors and Toyota. I don t care who you are or how good you get, you re still going to get it wrong sometimes and I am among the world s best examples.
3 The whole thing is just a bunch of rectangles.
4 The front and back rectangles are slanted at the top.
5
6 Back
7
8 Front
9 Of course, if you have a Miter Saw, it s all easier. Once you get your angle marked, you just set the saw and no more angle marking.
10 My angle turned out to be 38.
11 When building for myself, a trick I use whenever possible is to design with precut (Factory) lengths. 2 x 4 s come in 8, 10, 12 etc. lengths. If you make you thing (whatever it is) 8, 10 or 12 long to start with, you make less cuts and end up with less waste. The Raised Bed box was already 8 long so I had to buy 10 pieces for the Greenhouse and do a lot of cutting.
12 All the other rectangles are just simple boxes.
13 The first thing I did was to build the front, back and sides. Yours may be different but the dimensions here are: Back Legs 4-1 ½ long side, Side Legs 1-6, Front Legs 1-10 ¾ long side, Back and Front Base & Top 8 8 and Side Base & Top 2-7. The legs are all 2 x 4. The Bases and Side Tops are all 1 x 4 and the back and front Tops are 1 x 6.
14 The tops of the front and back rectangles form the top and bottom of the first layer of the roof. This goofy statement will be make sense later. When using the bigger screws ( I predrilled the holes.
15 I built the whole thing in two days. Before power tools, it would probably have taken two weeks..maybe a month.
16 Next I added the sides of the first layer of the roof. My dimension on these sides is 3-2 1/8 but you should measure yours in place to be sure.
17 Possible mistake: I could have put these together with StrongTie Plates but I was too lazy to go back to the store so I just glued and toe nailed them together with screws.
18 Next I added the 2 nd layer of the roof. In this picture I colored the 2 nd Roof Layer Blue so you can see the difference between it and the 1 st Layer. Whereas the 1 st Layer is made of 1 x 6 s, the 2 nd Layer is made with 1 x 4 s. It s just glued and screwed down using the 1- ¼ Yellow Screws. Don t go by my dimensions..they are off the CAD drawing and allow no tolerance. Measure these pieces in place.
19 This shows the 1 st and 2 nd Layers of the Roof. The 1 st Layer is 1 x 6 and the 2 nd Layer is 1 x 4.
20 Next I put the Lid together. It fits inside the 2 nd Roof Layer and I have colored it purple so that you can see the difference between them. The Lid is also made of 1 x 4 s. Again, do not go by the Lid dimensions here. Measure your pieces in place.
21 This time I hauled my lazy butt up to the store and bought the Simpson StrongTie Angle Brackets to pin the Lid together.
22 I used a pencil for a spacer between the lid and the Second Roof Layer (all the way around) to be sure there would be enough clearance between them. This is why I said not to use my dimensions and to measure all the top parts in place.
23 When I got the Lid assembled, I added the Hinges. I put one in the center and one at each end.
24 I put the whole thing together in the garage first.
25 Leaving the rectangles and as much as possible intact, I took it apart and hauled it around to the back yard. The back sits on the Raised Bed Box and almost flush against the fence. You leave a small space (about ½ unless you buy thicker Foam Board) between the fence and back rectangle for the Foam Board which will be inserted later.
26 Now would have been the best time to do it..and when you should do it. The Sides and Front are screwed into the Bed Box so that the insides of them are flush with the inside of the Bed Box.
27 This means the Sides and Front will overhang the Bed Box on the outside about 2.
28 I was able to keep most of the front intact and still manage to move it to the backyard.
29 With the entire frame assembled, I inserted the lid and reattached the hinges.
30 After getting it all together, I noticed that when I propped the Lid up in the center, it sagged on the sides a little.
31 So I had to add a 1 x 4 to stiffen it.
32 Cutting the Plastic: You can reverse a fine tooth circular saw blade if you have a lot to cut and I have done it for bigger projects.
33 For something small like this, I find it s less trouble to just use scissors.
34 I started with the front. As unusual luck would have it, 4 pieces cut to length worked out just right for the front.
35 Set a board along the bottom and about 2 below the base, to rest the plastic on.
36 Put the top of the Plastic even with the top of the 1 st Roof Layer and over hang it a little (1 ½ maybe) on the sides to wrap it around the corner. Here is another oversight: When I got to this point, I realized that I didn t have anything to screw the plastic to.
37
38 So I had to add a 1 x 4.
39 And offset the center post to accommodate it.
40 When you get your first piece measured and cut, use an ink marker like a Scripto or Sharpie to mark and cut the others. Do the same for the angled pieces on the sides.
41 This time, mine didn t work out like the front and I had to cut some odd pieces.
42 Now you need some kind of adhesive to attach the Foam Closure strips. I put the adhesive on both these things (Square Horizontal Foam Closure) and whatever I was sticking them to.
43 Then you stick them all around the edges of the Plastic wherever the heat might escape.
44 I had to cut it into small pieces to fit on the angle sides.
45 Run a temporary board around the bottom and about 2 below the base to rest the plastic on while you screw it on.
46 Overlap, bend and screw the plastic around the corners.
47 Run the plastic long on the lid all the way around to completely cover the top and over hang an inch or so to prevent any water from getting in.
48 At the top, run the plastic to about the center of the top of the Lid and just low enough to be out of the way of the hinges. When the Lid is open, the plastic needs to be able to clear this piece of drip edge that I put there to keep leaves from accumulating in the crack.
49 When the plastic is all attached, add a short piece of wood at the bottom of the lid and attach the handle.
50 Well dumb me, here s another screw up. It would have been easier to put the Foam Board in before attaching the Plastic.
51 But it s not impossible; you just have to wiggle it around until you have it where you want it. Also, I forgot, I squirted the Foam Board Adhesive all over the fence before I added the Foam Board.
52 It wasn t long enough so I had to cut another piece.
53 And tape the seam with this reflective tape.
54 When it started getting down to freezing, I decided to seal up all the cracks with Weather Strip.
55 I m not going to try to tell you everyplace to put it. Just look around all over the thing for anyplace where heat might escape..all around where the lid closes and any other spots you might notice. It s all pretty well assembled now and this thing is getting to damn long so I think I ll do it in three parts. Part Three
Greenhouse Plans_Part_One Tools & Materials
Greenhouse Plans_Part_One Tools & Materials Materials: All lumber is treated. I don t know what size yours will be and I don t remember well (anything) but this is approximately what I bought for mine:
More informationHow to Build a Raised Bed Cold Frame
How to Build a Raised Bed Cold Frame Protect your plants from frost with a cold frame that sits right on top of your existing 4' x 4' raised bed. The lid is held open with screen door closers, and the
More information2.9 WINDOW & DOOR BUCKS
2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationREGENCY TIMBER BUILDINGS
REGENCY TIMBER BUILDINGS TEL 01948 830460 UNIT 22 PENLEY IND EST, PENLEY.WREXHAM. LL13 0LQ 1 Garage fitting instructions Tools needed handsaw, hammer, Stanley knife with hook blade, tape measure, battery
More informationAl Keller s Inexpensive Backyard Greenhouse Plans
Al Keller s Inexpensive Backyard Greenhouse Plans There are many ways to construct low cost greenhouses for your property. This is just one man s design, using easily obtainable and fairly inexpensive
More informationWanderlust Suitcase Vanity
Wanderlust Suitcase Vanity If you re like me, you re always up for an adventure. When I saw some examples of DIY reclaimed suitcases, paired with the exciting new Wanderlust embroidery design collection,
More informationInstallation Instructions Split Shake, Staggered Shake, Shingle, Perfection Shingle, and Shapes
Installation Instructions Split Shake, Staggered Shake, Shingle, Perfection Shingle, and Shapes General Guidelines These instructions show one type of installation and are intended for the professional
More informationA Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.
A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationOutdoor Storage Locker
Easy To Build Outdoor Storage Locker A little shed that spells big relief for a crowded garage Complexity: Simple Cost: $100-$500 Assemble this easy-to-build storage locker for your outdoor tools. It's
More informationOutdoor Cooler Cart. Outdoor Cooler Cart Construction Instructions
Outdoor Cooler Cart Outdoor Cooler Cart Construction Instructions Make the Legs and Side Panels. Cut the eight long and short leg pieces to length. See Material List on next page.. Apply a bead of glue
More informationSkybolt V2 Construction Manual
Skybolt V2 Construction Manual Property of www.ppgplans.com Do not duplicate or make public. Warnings & Disclaimers. This product shows how to build a basic frame only for Powered Paragliding. It is the
More informationThe easy way to an affordable kitchen
quality, affordable, pre-assembled The easy way to an affordable kitchen In association with All Insta-Cupboard carcass units are supplied pre-assembled to simplify installation Choose the colour of your
More informationRouter Table-Mate. Everything you'd want in a router table for just $50.
Router Table-Mate Everything you'd want in a router table for just $50. Commercially made router tables are everywhere these days. Some of them come with more gizmos and gadgets than a 59 Edsel. By the
More informationSmall Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)
1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x
More informationirdhouse Table Special Tools and Techniques Materials and Supplies Hardware
B irdhouse Table This whimsical table is one of our favorite projects, because it never fails to produce a smile on the faces of our backyard guests. Not only is it cheerful to behold but the glass top
More informationInstalling Your New Creature From The Black Lagoon Tail Light DMD Panel MOD
Installing Your New Creature From The Black Lagoon Tail Light DMD Panel MOD A few things before we start: The wooden speaker panel provided in this MOD was manufactured using a Precision CNC machine and
More informationShop Projects. Plans NOW. Each Built from One Sheet of Plywood!
Plans NOW www.plansnow.com 5 Shop Projects Each Built from One Sheet of Plywood! Tool Tote - Sawhorse - Workbench - Wood Bin - Wall Cabinet PLUS: 7 SHOP SECRETS Working with Plywood Dread the thought of
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationMaterials for Peppermint Candy Pillow
Peppermint Candy Pillow Tutorial This adorable Peppermint Candy Pillow by BERNINA Ambassador Nancy Mahoney will give your decor a new look, whether for your bed or a decorative pillow for your couch. The
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationCastle loft bed [1] Additional Photos. Castle loft bed Published on Ana White (http://www.ana-white.com)
[1] Submitted by fsmumford [2] on Tue, 2011-10-18 21:51 [1] Additional Photos [3] [4] Page 1 of 31 [5] [6] [7] Summary: I stumbled upon Ana s blog about a year ago. Since, like many of you, I have become
More informationGambrel Barn with Overhang Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationHow to install a leather Redline Goods armrest cover on your Audi B5 ( A4, S4)
How to install a leather Redline Goods armrest cover on your Audi B5 (1996-2001 A4, 2000-2002 S4) The following pictures are of my U.S. 2001.5 Audi S4 with light gray factory interior, installing a black
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationCONSTRUCTION GUIDE 21ft Wide and 24ft Wide SHEEP HOUSE
The Outside, Inside CONSTRUCTION GUIDE 21ft Wide and 24ft Wide SHEEP HOUSE Thank you for purchasing a Premier Sheep House. Please take the time to carefully read through this Construction Guide before
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationPLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED
PLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED DIMENSIONS: 82" X 70" X 45" DIFFICULTY LEVEL: INTERMEDIATE TOOLS REQUIRED ONE+ Circular Saw ONE+ AirStrike 16GA Finish Nailer ONE+ Impact Driver ONE+
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationPassport Cover. You will need:
Passport Cover Got that seasonal wanderlust? Ready to break in that new passport? Worried about losing said passport to wear and tear? Or maybe you just want to make a statement and glam up that plain
More informationCabinetry Installation
Cabinetry Installation Easy to follow step-by-step kitchen cabinet installation Hammer Pry bar Screwdriver Phillips Flathead Level TOOL AND MATERIAL LIST Tape measure Pencil Straight edge Drill 3/16" drill
More informationTrunk. Hood. Roof 1 15/16 3 1/4 2 9/16 3 1/4 3 1/4 5 1/4
Hood Trunk 1 15/16 3 1/4 2 9/16 3 1/4 2 5 1/4 3 1/4 Roof WARNING All the instructions in this are just from how I have done on my car so I don t guarantee anything if you follow these instructions and
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING BASEMENT EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail
More informationT-Top Headliner Repair Guide With detailed instructions
T-Top Headliner Repair Guide With detailed instructions Supplies: Fabric: 1 ¼ yards will do -You can use any kind of fabric you want. Some fabrics will be harder to install than others. I d highly recommend
More information10 Easy-to-Build. Plywood Projects
10 Easy-to-Build Plywood Projects Ten shop projects ten sheets of plywood. These rock-solid essentials take just a couple hours to build and will help you make the most of the space in your shop. All content
More informationInstallation Instructions for Siding
Smart-Shingle TM System "The new smart way to install cedar shingles." - This Old House Installation Instructions for Siding V3.2 INSTALLATION GUIDE MARKS Shingle-Strip 0 1 2 3 4 5 6 7 8 9 10 11 12 13
More informationI found the job quite straightforward and would have done it in about half an hour if I hadn t kept stopping to take pictures and write notes.
SmartStart Installation The following describes how I installed a Dometic SmartStart Model #4220040 on the Dometic 600312.331 Penguin Air Conditioner on my Escape 19 Trailer. I had no problems following
More informationFrameSaver Jamb Bottom Replacement Instructions
FrameSaver Jamb Bottom Replacement Instructions 8817 West Market Street Colfax, NC 27235 800.334.2006 www.enduraproducts.com Utility Knife Straight Edge Circular Saw Reciprocating Saw Miter Saw Shims Screws
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL
ASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL January 2013 The SL500A is a square upright glass cabinet with a single hinged lockable door. It has five adjustable shelves plus the base. It also has an optional
More informationmermaid quilt a sewing pattern by
a sewing pattern by mermaid quilt This project is a simple and straightforward piece for applique lovers. I personally designed it for a coworker s daughter -- a sweet little girl who s current obsession
More informationconstruction? I use a lot of construction terms. Hips and valleys comes from roofing actually. And there we go, just like that. Nice and easy, right?
Hey everybody, welcome back to Man Sewing. I m so glad you re following along. I ve got another fantastic quilt tutorial for you today. Now the reason I say it s fantastic is because I think I came up
More informationINSTALLATION PROCEDURE
Vinyl Siding INSTALLATION PROCEDURE Tools Needed and Preparation MOST ESSENTIAL TOOLS The proper tools, materials and equipment can make the installation of Durabuilt Vinyl Siding much easier. Here are
More informationInstallation Instructions Palladium Wall Panels - Demountable Factory Finished Edges and Field Cut Edges
Please read all instructions before installing Palladium Wall Panel System. 1. Before installation: a. Acclimate Palladium Panels, reveals, adhesives and wall substrates to room temperature 24 hours before
More informationINS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...
INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...
More informationThe Process of Building Cabinets As a result of the questions and input during the skill topic portion of the May and June meetings I ve put this
The Process of Building Cabinets As a result of the questions and input during the skill topic portion of the May and June meetings I ve put this article together. It occurred to me (at least from where
More informationInstallation Guidelines
TM TM Installation Guidelines * Guidelines also apply to installation of astroeco products More For Pre-Engineered Metal and Post-Frame Buildings icient, Safer To Use and Easier To Install Than Regular
More informationour strips. So it made really good use of this roll up. So we hope you enjoyed this tutorial on the Stair Step block from the MSQC.
Hi I m Jenny from the MSQC. And I ve got a really fun project for you today. Take a look at this quilt behind me. Isn t this gorgeous? I love these fabrics. I love the blues. It just makes me feel like
More informationA Simple, Inexpensive Gun Cart By Marauder
In The Beginning... A Simple, Inexpensive Gun Cart By Marauder When I first started shooting Cowboy Action, it was obvious that I needed something to easily carry my guns and stuff. So I made a simple
More informationMetro Series Sauna. installation instructions
Metro Series Sauna installation instructions Please immediately check for any hidden damage that may have occurred in shipping. If any damage is found you must notify the delivering carrier within seven
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationHood stripes Tools needed from AutoZone or any auto parts store: bottle spray, squeegee, a towel that you re using to clean you car up after washing,
WARNING These following pages are instruction for C5 CE stripes; however, it is the same method applying vinyl. Please spend time to read thru these pages. At the end, it is your C5 ME 1 stripes instruction.
More informationWheelchair Quilts. A guide to make fitted quilts for those in a wheelchair
Wheelchair Quilts A guide to make fitted quilts for those in a wheelchair Table of Contents Introduction Creating a Template Fitting the Template p. 2 p. 3 p. 5 Sew Blocks or Pattern p. 8 Quilt Top Assembly
More informationBuild It: The Most Amazing Cooler Bench Ever
Build It: The Most Amazing Cooler Bench Ever wooditsreal.com/2017/04/28/build-it-cooler-bench-free-plans/ A bench. A cooler. Put them together and what do you get? The most amazing Cooler Bench you ve
More informationWARNING These following pages are instruction for C5 CE stripes; however, it is the same method applying vinyl. Please spend time to read thru these
WARNING These following pages are instruction for C5 CE stripes; however, it is the same method applying vinyl. Please spend time to read thru these pages. At the end, it is your C5 side stripes' instruction.
More informationTutori-O: Spacer How to Make a Mini Miter Box. /mini-miter-box-tutorial. DIY Dork Tutori-O: How to Make a Mini Miter Box
1 DIY Dork Tutori-O: Spacer How to Make a Mini Miter Box www. /mini-miter-box-tutorial 2 Published by: Kevin Torrence kevin@diydork.com Copyright 2011 - Kevin Torrence. All rights are reserved. No part
More informationWallpaper. the Right Way. Wallpaper is trendy again, both with designers, who are speccing it more often, and
Wallpaper the Right Way Installed correctly, this wall covering should last a lifetime and come off easily once it has worn out its welcome By John Clift Wallpaper is trendy again, both with designers,
More informationMach Wall Installation Instructions
Mach Wall Installation Instructions Planning the Job Since Mach Wall is an innovative product that accomplishes 3 tasks at the same time (frame, insulate and drywall) and it replaces traditional framing,
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More informationGIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
More informationLUX INSTALLATION GUIDE. LUX Panel V Groove Installation. Installation Guide. February
LUX Panel V Groove Installation Installation Guide February 2017 www.luxpanel.ca LUX Panel V Groove Installation LUX panel steel cladding is designed to be installed vertically, horizontally, diagonally
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationAbove are the offsets for the plywood panels.
DinkyDink Plans Bottom Panel Half Station X Y X2 Y2 1 1/4 3/4 0 11 5/16 2 4 9/16 4 12 9/16 3 11 11/16 1/4 11 7/16 14 1/2 4 18 5/8 1/16 18 5/8 15 11/16 5 25 3/4 0 25 3/4 16 5/16 6 32 13/16 0 32 13/16 16
More informationPocket Door Installation Instructions
Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code
More informationBuilding dimensions supplied by the #1 supplier of cornhole bags and boards on the internet.
Building dimensions supplied by www.cornhole-game.org, the #1 supplier of cornhole bags and boards on the internet. SUPPLIES QUANTITY (1) ½ FIBERBOARD (PLYWOOD) SHEET - 4 X 8 (3) 2 X 4 BOARDS - 8 LONG
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e Download 12,000 More Shed Plans
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e Download 12,000 More Shed Plans Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationRoofing Training - Basics. Sandy Wesch
Roofing Training - Basics Sandy Wesch Tools Hammer Measuring Tape Chalk Line & Chalk Speed Square Framing Square Utility Knife Metal Snips Extension Ladder(s) 2 Safety Any tools or material up on the roof
More informationCUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS
20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air
More information10 x 10 Flat Top Pergola
0 x 0 Flat Top Pergola A S S E M B L Y G U I D E Models: Venetian, Tuscany, Luxor, Acadia O P T I O N A L A C C E S S O R I E S Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post)
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationgravity feeder GRAVITY FEEDER
Z5979i_pg066-077.indd 68 3//10 4:09:48 PM gravity feeder USING A TRIED-AND-TRUE DESIGN, GRAVITY feeders can hold a large amount of chow. The wide opening at the bottom accommodates a seed mix containing
More informationINSTALLATION INSTRUCTIONS FOR A&L PRODUCTS
INSTALLATION INSTRUCTIONS FOR A&L PRODUCTS AUGUST 2017 1 RECOMMENDED BUILDING IN-DETAIL Should you require further information, please contact A&L Windows on 1800 441 414 2 IMPORTANT IMPORTANT Allow Vinyl
More information3/ /
SUNGLAZE system is designed for both rafter and purlin construction options. Recommended minimum roof slope for Sunglaze applications is 5 o. Where lower slopes are necessary, we recommend rafter construction.
More informationSTORAGE SHED. Storage Shed Project Plan #854 Sheet 1 of Riverside Dr., Suite 212 Metairie, LA SouthernPine.com SouthernPineDecks.
STORAGE SHED Project Plan #854 Sheet 1 of 6 Enjoying your backyard can be relaxing, but it can also get crowded. There s lawn furniture, gardening tools and supplies, camping gear, maybe even pool equipment.
More informationCONTENTS. Transitions Board and Batten Vertical Installation... 10,11
INSTALLATION MANUAL CONTENTS Important Notes... 2-4 Weather Protective Barriers... 2 Storage and Transportation... 2 Tools and Equipment... 2 Fastener Choices... 3 Wall Preparation... 3,4 Flashing... 4
More informationinstallation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty
installation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty Installation Instructions As with any building project, use proper
More information1. Make sure the bender board is free of knots with at least one good edge and no cracks the full length to 2 ¾ wide
MATERIALS: 2-18 ft x ½ redwood bender boards 1-6 ft redwood 2 x 4 (for the rails or feet) In the video I say one 18 foot piece of bender board. You have to do everything right to get all you need out of
More informationHAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this.
HAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this. Tool (Name & Nut drivers Speed Square Adjustable Bevel Square CONSTRUCTION TOOLS: Tool (Name
More informationClassic Saltbox Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box
More informationMax and Emily s Corner: Garden Shed. Please excuse our mess, it s still a work in progress!
Max and Emily s Corner: Garden Shed Please excuse our mess, it s still a work in progress! B elow you will find the sketches that I drew up for building our 10 x12 garden shed project. I won t be providing
More informationWave Profile Installation Guide
Wave Profile Installation Guide American Pa o Covers Plus Proudly Builds With Tools & Hardware Wave Profile Installation Guide Tape Measure Square Level Felt tipped Marker and/or grease pencil 3/8" Nut
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationScratch Build a Water Tower
Here s some Prototype details Photos Courtesy of Rodney Doster Water Spout and Discharge Pipe Tank Bands Here s some more Prototype details Photos Courtesy of Rodney Doster Weather Vane as a Finial Using
More informationI love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal
Limbert Chair 9 I love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal camp chair for under $20. But when you
More informationMcCue Bumper Installation Instructions
McCue Bumper Installation Instructions McCue 8" Bumper Tools Required: Saw with 10-12" blade Tape measure Flat head screwdriver Phillips screw driver Pencil or chalk line Drill with Philips driver bit
More informationlondon calling bag a sewing pattern by
a sewing pattern by london calling bag This project on its own is a very big gusseted bag with a zippered top closure. But the optional details include a front pocket with Union Jack applique, buckle adjustable
More informationHow to make a paper mache skull
http://www.spookyblue.com/halloween/skulls/paper mache skull.htm How to make a paper mache skull Materials List Resin skull from Anatomical Chart Company What?! Spend $25 on a skull? Hear me out. A good
More informationAlmost Heaven Saunas THE AUTHENTIC SAUNA EXPERIENCE. Worthington Sauna Installation & Owner s Manual
Almost Heaven Saunas THE AUTHENTIC SAUNA EXPERIENCE Worthington Sauna Installation & Owner s Manual Read this entire manual through to the end before proceeding with the assembly. ELECTRICAL REQUIREMENTS
More informationAngel Pets Memorial Mug Rug PDF Pattern
Angel Pets Memorial Mug Rug PDF Pattern Finished Size: 6 1/2 x 8 inches If you are only making one animal, be sure to print only that page. Use these with a snack, or hang on your wall. They also make
More information15 - Interior. Interior. February GGG Page 15-1
Interior February 2003 15-GGG Page 15-1 15 - Interior This Page Intentionally Left Blank Page 15-2 15-GGG February 2003 Contents 15.0 - Chapter Preface...15-4 15.0.1 - Parts List...15-4 15.0.2 - Tools
More informationSweet Pea Garden Bunk Bed Roof and Pergola [1]
[1] Submitted by Ana White [2] on Wed, 2012-09-26 15:34 Page 1 of 22 [1] Page 2 of 22 Hello Sweet Pea Bunk Bed Builders! To add maximum cuteness to the Sweet Pea Bunk Bed [3], one must of course add a
More informationHow to make a Wendy house Part One: The Floor and the Frame
How to make a Wendy house Part One: The Floor and the Frame The Wendy House. This wendy house is basically a playhouse with a few feminine touches added. A wendy house can give children hours of enjoyment.
More informationIt can be either a 2½ seater bench seat (2 adult and a kid), or a 5 seater picnic table.
Page 1 Folding picnic table in both bench-seat and picnic table mode Introduction Description A single bench seat that can be changed into a picnic table with ease. This 'Bench come Picnic Table' is ideal
More informationPage 1. FIG. #1 - Shower Door Assembly SHOWER & BATH ENCLOSURES BUILT TO LAST A LIFETIME HANDLE ASSEMBLIES REMOVED FOR CLARITY.
FIG. #1 - Shower Door Assembly 29 1 2 1 6 9 9 5 HANDLE ASSEMBLIES REMOVED FOR CLARITY. 25 25 PLEASE REFER TO FIG. #2 FOR INSTALLATION 26 12 17 18 18 17 10 3 11 7 10 8 Page 1 FIG. #2 - Top View 5 21 10
More informationHow To Install Asphalt Shingles. Part 1 of 3: Preparing the Roof. Tutorial
Tutorial How To Install Asphalt Shingles Installing new shingles yourself can save considerable time and money, and you can follow the same steps they do to achieve the same professional look. Re-doing
More information