INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Julia Williams
5 years ago
Views:

1 Accessory Application Publications No. INSTALLATION INSTRUCTIONS AERO 2009 TSX BII Issue Date APRIL 2008 PARTS LIST TOOLS AND SUPPLIES REQUIRED Front aero bumper Phillips screwdriver Flat-tip screwdriver Drill 3 mm, 6 mm, and 10 mm Drill bits 16 mm Hole saw File Lower grille Ratchet 10 mm Socket Pushpin Utility knife Plastic Trim Tool (T/N SILTRIMTL10) Right air spoiler Container Blanket or cardboard Illustration of the Front Aero Bumper Installed on the Vehicle Left air spoiler 15 Bolts 8 Self-tapping screws AERO AT 10 Nuts 2008 American Honda Motor Co., Inc. All Rights Reserved. BII (0804) 08P02-TL2-2A of 8

2 INSTALLATION Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 2. Remove the two self-tapping screws, ten short clips, and two long clips from the front bumper. NOTE: Be extremely careful not to damage the body. To prevent damage, rest the front bumper on a blanket or cardboard during the installation. Before removing parts, note their locations so that they can be reinstalled in their original locations properly. 1. Open the hood and remove the radiator cover (eight clips). 2 LONG CLIPS 10 SHORT CLIPS 2 SELF-TAPPING CT 8 CLIPS 3. Release the eight tabs on one side of the vehicle, and pull the front bumper toward you. Release the eight tabs on the other side of the vehicle the same way. 5 TABS 3 TABS RADIATOR COVER T Pull AT 2 of 8 BII (0804) 2008 American Honda Motor Co., Inc. All Rights Reserved.

3 4. Remove the front bumper (unplug the two fog light connectors). Have an assistant help you when removing and installing the front bumper. Place the front bumper on the blanket to prevent damage. 6. Remove the center induction plate from the front bumper (five self-tapping screws, four clips, and four retaining tabs). 4 RETAINING TABS CENTER FOG LIGHT CONNECTOR 5 SELF-TAPPING BT AT 7. Remove the left fog light from the front bumper (three self-tapping screws). Remove the right fog light the same way. 5. Remove induction plate A from the front bumper (four clips and five bolts). A LEFT FOG LIGHT 5 BOLTS (Discard.) AT 3 SELF-TAPPING AT 2008 American Honda Motor Co., Inc. All Rights Reserved. BII (0804) 3 of 8

4 8. Remove the left induction plate from the front bumper (one self-tapping screw and two hooks). Remove the right induction plate the same way. 11. Remove the two screws and the four clips from the back of the front bumper. Unhook and remove the front grille from the front bumper. LEFT Slide. HOOK 2 2 HOOKS SELF-TAPPING SCREW BT AT 9. Remove the two bolts and the self-tapping screw from the front bumper, and remove the license plate frame. 12. Using a pushpin, mark the front aero bumper at the center of the marks in the positions shown. This marks the location of the middle license plate frame screw. LOWER PUSHPIN 2 NUTS 2 BOLTS SELF-TAPPING SCREW LICENSE FRAME AT 10. Remove the two nuts from the front lower grille. MARK AERO BT 4 of 8 BII (0804) 2008 American Honda Motor Co., Inc. All Rights Reserved.

5 13. While wearing eye protection, drill the center induction plate at the two points in the positions shown using a 3 mm bit, and then a 6 mm drill bit. 14. Using a 16 mm hole saw, enlarge the two holes from the opposite side of the center induction plate. APPROX. 45 DRILL 16 mm HOLE SAW CENTER 16 mm HOLE SAW DRILL BIT 16 mm HOLE SAW HOLE CENTER DRILL (3 mm 6 mm BIT) DRILL (3 mm 6 mm BIT) BT AT 15. Use a file to remove any burrs from the edge of the holes. 16. Install the front grille on the front aero bumper reusing the two screws and four clips that you removed in step 11. Slide. HOOK 2 AERO AT 2008 American Honda Motor Co., Inc. All Rights Reserved. BII (0804) 5 of 8

6 17. Install the lower grille on the front aero bumper using eight self-tapping screws. AERO 6 RETAINING TABS 20. Install the left induction plate on the front aero bumper reusing two self-tapping screws (one from step 6, and the other from step 8). Reinstall the right induction plate the same way. LEFT AERO 8 SELF-TAPPING 8 RETAINING TABS LOWER AT 18. Reinstall the two nuts removed in step 10 onto the front lower grille. AERO LOWER SELF-TAPPING SCREW Removed in step 8. SELF-TAPPING SCREW Removed in step Install the left fog light on the front aero bumper reusing the three self-tapping screws that you removed in step 7. Install the right fog light the same way. AERO AT 2 NUTS 2 BOLTS SELF-TAPPING SCREW LICENSE FRAME AT 19. Install the license plate frame on the front aero bumper reusing the two bolts and the self-tapping screw that you removed in step 9. 3 SELF-TAPPING LEFT FOG LIGHT AT 6 of 8 BII (0804) 2008 American Honda Motor Co., Inc. All Rights Reserved.

7 22. Reinstall the center induction plate on the front aero bumper reusing three self-tapping screws and four clips that you removed in step Install the left air spoiler on the front aero bumper using five bolts and five nuts. Install the right air spoiler the same way. 3 SELF-TAPPING CENTER 5 NUTS LEFT AIR SPOILER AERO AERO 5 BOLTS AT BT 23. Reinstall the induction plate A on the front under spoiler using five bolts and reusing the four clips that you removed in step Install the front aero bumper, and reconnect the fog light connectors. A FOG LIGHT CONNECTOR 5 BOLTS AERO AT AERO BT 2008 American Honda Motor Co., Inc. All Rights Reserved. BII (0804) 7 of 8

8 26. Secure the front aero bumper reusing two self-tapping screws, ten short clips, and two long clips you removed in step 2. AERO 2 LONG CLIPS 10 SHORT CLIPS 2 SELF-TAPPING CT 27. Reinstall the radiator cover. 8 of 8 BII (0804) 2008 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver