Camp Loft Bed with Stair, Junior Height [1]

Transcription

1 [1] Submitted by Ana White [2] on Wed, :30 [1] Additional Photos Page 1 of 28

2 [3] [4] [5] [6] PLAN UPDATE: I have revised step 1 of this plan to increase the safety of the platform, so there is no more than a 3" gap between the stair rungs. If you have built this bed, you can simply add another "rung" to the stair part to increase the safety at the platform area. Before we get to a plan, I simply must warn you. Do not build this bed if you want any of the following to happen: Page 2 of 28

3 Your kids to play independently in their room for hours and hours and hours... if you build this bed, you will see your kids 30-40% less... Page 3 of 28

4 Do NOT build this bed if you want your kids to take a nap, all by themselves... It's like a protected nest up there, with rails on all sides, and easy access with stairs. They just climb up there and go to sleep. No snuggling required. Page 4 of 28

5 Page 5 of 28

6 If you build this bed, you will miss out on lots of smiles and laughter and pretend play. And when you come try to join in, they will start giggling and say, Mom! Leave us alone, we're playing horses! Or store or house or pretending the stair platform is a stage. The only reason I built this bed was because the room is so tiny (8x8 with small closet) it was very difficult for the kids to play, and then put their things away in a space the size of a short hallway. We'd done a loft bed years ago, but the loft bed was only accessible by children, and there was no where for guests to sleep in our house. Page 6 of 28

7 Page 7 of 28

8 So we needed a loft bed WITH STAIRS that is sturdy and easy to access in a TINY room. With the window right there, I just didn't know how to make it work. And then one day, I realized that the stairs do NOT need to go all the way up to the bed. They only need to go up about 18" to 24" (normal height of kids mattress above floor) below the mattress. Page 8 of 28

9 The window was previously the obstacle in the way of building stairs. Page 9 of 28

10 Now it's entertainment for the kids as they watch the chickens run around the back yard. Page 10 of 28

11 Page 11 of 28

12 Under the bed, no storage is lost. I've been debating adding some custom sized rolling toy bins but the giant canvas bag is doing fine holding pillows, blankets and stuffed animals. It is no exaggeration to say they play in their ALL DAY. I'm considering making a felt curtain for the front too... Page 12 of 28

13 The best part about this bed is how easy and inexpensive it is to make. That's all 2x4s and 2x6s (I'll share my finishing technique with you later this week) bringing the total cost of lumber up to about $50!!! Page 13 of 28

14 And I don't know how easy this bed was to build personally, all I can say is I printed off the plans and handed them to the Ram and Grandpa Tim and said, I'll be out after I finish my post. Two hours later I headed out to the garage and the bed was DONE! Now it's your turn!!! Summary: Loft bed plans with stairs. Junior height loft bed plans free from Ana-White.com CategoriesProject Type: Bunk Bed [7] Twin [8] Beds [9] Room: Kids and Toys [10] Skill Level: Beginner [11] Style: Children's and Kid's Room Furniture and Toy Plans [12] Dimensions: Dimensions shown above. Fits twin. Dimensions: Page 14 of 28

15 14 8 feet long 4 8 feet long 2 8 feet long 1 8 feet long 2 ½ PH screws Tools: Page 15 of 28

16 [13] [14] [15] Page 16 of 28

17 [16] [17] Cut List: 4 65 ½ 2 37 ½ 5 37 ½ ½ 2 37 ½ 1 41 ½ 2 20 ½ (both ends cut 45 degrees off square, ends NOT parallel) to be trimmed down in later steps 6 7 ¾ (both ends cut at 45 degrees off square 6 20 ½ General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Step 1 Page 17 of 28

18 [18] Build the ladder end as shown in diagram with 1 1/2" PHs and 2 1/2" PH screws. Use glue to fasten - these joints are permanent. If you are building this loft bed without the stair platform, add 2x4s all the way down to make a "ladder" for the kids to climb up. Step 2 Page 18 of 28

19 [19] Build front end of loft bed same as ladder end. Step 3 Page 19 of 28

20 [20] Now here's where we skip the glue. To make this loft bed easy to disassemble, I did not use glue here. The inside width for the mattress area should be 39", insetting the side rails 1 1/4" from outsides. I did this so your PH screws have lots of board to grab into. This bed has NOT been weight tested or guaranteed. If you feel you need extra support - add metal brackets under the 2x6s. An alternative method is to attach metal bed brackets directly to the ends if you have those. Notice the cleat is added in this step to. I used 2 1/2" screws and glue to attach, screws every 6-8" all the way down. Page 20 of 28

21 This bed is designed to work with a bunkie board, but we just used 2x6s cut to length as the bed slats. Step 4 [21] Now we'll start building the stair platform for the loft bed with stairs. Step 5 Page 21 of 28

22 [22] Build the floor framing section and attach to the floor legs. I recommend 1 1/2" PHs and 2 1/2" PH screws and glue here. Step 6 Page 22 of 28

23 [23] And then the decking is placed on top of the stair platform. Step 7 Page 23 of 28

24 [24] The stairs are easy to build - just 45 degree angles! We went ahead and drilled 1 1/2" PHs along top edge of the stairs to connect the stairs to the bed later on. Step 8 Page 24 of 28

25 [25] Then we added the stair treads. We also drilled 1 1/2" PHs along ends of the stair treads and attached with 2 1/2" PH screws just for extra strength. Everything gets glued. Step 9 Page 25 of 28

26 [26] Step 9 Instructions: The bed was finished outside and then assembled in the room. TIP: We haven't found our bed needs it, but for extra support, you could add another 75" (at $2 a 2x4, cheap insurance) to the base of the bed to further support the bottoms. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color Page 26 of 28

27 evenness and adhesion. Use primer or wood conditioner as needed. Source URL: d-stair-junior-height Links [1] -height [2] [3] jpg [4] jpg [5] jpg [6] jpg [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] jpg [19] jpg [20] jpg [21] jpg [22] jpg [23] jpg Page 27 of 28

28 [24] jpg [25] jpg [26] jpg Page 28 of 28