Reclaimed Wood Look Bedside Table [1]

Transcription

1 [1] Submitted by Ana White [2] on Thu, :27 Page 1 of 18

2 [1] Additional Photos Page 2 of 18

3 [3] Featured photo by brick [4] This rustic three drawer nightstand is easy to build with off the shelf lumber and basic tools. Summary: Rustic bedside table or nightstand - farmhouse style. Free plans from ANA-WHITE.com CategoriesProject Type: Side and End Table Plans [5] Nightstands [6] Room: Bedroom [7] living room [8] Skill Level: Intermediate [9] Style: Cottage Style Furniture Plans [10] Farmhouse Style Furniture Plans [11] Estimated Cost: $50 - $100 [12] Dimensions: Dimensions shown above Page 3 of 18

4 8 feet long 8 feet long 8 feet long 8 feet long 10 feet long 1/4" plywood for back 3 knobs or pulls 3 sets 16" White Euro style drawer slides like shown in this plan [13] Common Materials: 2 1/2 inch screws Dimensions: Page 4 of 18

5 1 1/4 inch finish nails 2 inch finish nails 1-1/4" Pocket Hole Screws [14] 2-1/2" Pocket Hole Screws [15] Elmer's Wood Glue [16] Elmer's Wood Filler [17] 120 grit sandpaper primer wood conditioner paint paint brush Tools: Page 5 of 18

6 [18] [19] [20] [21] [22] Page 6 of 18

7 [23] Cut List: 14" (Side Trim) 23 1/4" (Side Panels) 27 1/4" (Legs) 16" (Front/Back Tie ins) 14" (Center Tie In) 1-1/4" 19" x 23 1/4" (Back) 21" (Top) 21" (Top) 21" (Top Front) Drawer cut list in plan Cutting Instructions: Dire to the success of this project is using straight boards that measure true to width as follows: 1x6-5 1/2" wide 1x4-3 1/2" wide 1x3-2 1/2" wide 2x2-1 1/2" x 1 1/2" If your boards do not measure to these widths, you will need to adjust the plan. If your boards are not straight namely the 1x4 side panels, you could have trouble with the drawers. General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Page 7 of 18

8 [24] If you have a Kreg Jig [18], attach the panel boards to each other first with 1 1/4" pocket hole screws, with your jig set for 3/4" stock. This will make the panel a solid piece. Attach with 1 1/4" finish nails and wood glue the panel trim, flush to top and bottom. Ensure that your panels are square (very important!) Step 1 Page 8 of 18

9 If your panel boards are not coming out flat, do this sort of thing with additional 1x2s - lined up with the front tie ins. Page 9 of 18

10 [25] Now attach legs to ends of panels as shown in diagram, flush to tops. Step 2 Page 10 of 18

11 [26] Whenever you build for drawers it is crucial that your project is very very square, or your drawers will not slide correctly. Attach the front/back tie ins, and check the entire project for square, measuring from opposite leg to opposite leg on both the top and bottom of the legs. You can also use 2 1/2" screws and wood glue to attach tie ins, with predrilled screws and wood glue. Step 3 Page 11 of 18

12 [27] Add the center support as shown above. Step 4 Page 12 of 18

13 [28] Attach back plywood with finish nails and wood glue. Step 5 Page 13 of 18

14 [29] Now the top, start at the back with the 1x2 and attach flush to the back, 1" overhangs on both sides. Continue adding 1x4s, and finally, the front is a 1x3... Would be super cute to leave the top wood and paint the base a distressed finish. Step 6 Page 14 of 18

15 [30] Now the drawers... Super important to build square drawers. Your drawer boxes should be built 1" less in width than the drawer housing (the interior of the project) to give clearance for drawer slides. The "perfect" measurements are shown here, but you may need to adjust for differing board thicknesses 14 1/2" (Sides) 15" (Fronts and Backs) 3-1/4" 16" x 15" (Drawer Bottoms) /4" (Drawer Faces) Don't add the drawer faces quite yet. For a drawer with higher sides, you can also use 1x4s. Step 7 Page 15 of 18

16 [31] Install drawer boxes as shown above, inset by 3/4" from the front of the project. Make sure your drawers slide well. Then position the drawer faces over the drawer boxes until there is an even 1/8" gap on all sides and nail drawer faces on. Be aware of hardware locations so you don't have to drill through nails later. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as Step 8 Page 16 of 18

17 needed. Source URL: Links [1] [2] [3] son%20bedside%20table%2011.png [4] ght-stand [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] TF8&camp=1789&creative=390957&creativeASIN=B U2&linkCode=as2&tag=knooffwoo-20&linkId=5AJJ GUAWGYX2TT7E [15] TF8&camp=1789&creative=390957&creativeASIN=B00 0BN7DLU&linkCode=as2&tag=knooffwoo-20&linkId=XL DYGROR7GI4SHLA [16] [17] struction# [18] [19] [20] [21] [22] [23] [24] Page 17 of 18

18 ason%20bedside%20table%203.png [25] ason%20bedside%20table%204.png [26] ason%20bedside%20table%205.png [27] ason%20bedside%20table%206.png [28] ason%20bedside%20table%207.png [29] ason%20bedside%20table%208.png [30] ason%20bedside%20table%209.png [31] ason%20bedside%20table%2010.png Page 18 of 18