Simtools - Installation
|
|
- Bathsheba Evans
- 5 years ago
- Views:
Transcription
1 Simtools - Installation Go to X-simulator.net and download the last version of SimTools : or Create an account login or Sign up Then install SimTool
2 Game Engine Connect the 2 USB cable to your PC. Normally, windows must download and install automatically the right driver. (if not go to then click right on CDM20802_Setup.exe and run as administrator, redo the operation : click right on CDM20802_Setup.exe and run as administrator) Launch the game engine and game manager of Simtool and see the icon near the time, click on the arrow and click on customize the icon notification. We recommend you to customize the icon notification of SimTools game manager and game engine in order to show the icon and all the notifications
3 Inside Game Engine Go to Settings-> Interface 1 and fill the 8 point Speed to and Acceleration to 500. For Interface 1 select COM3. For Interface 2 select COM4. Interface 3 select COM5 Interface 4 select COM6 Interface 5 select COM7 Notice: if you have COM10 or superior, you must change the COM port (see the end of this document) For Interface 1 select Axis 1. For Interface 2 select Axis 2. For interface 3 select Axis 3 For Interface 4 select Axis 4 For Interface 5 select Axis 5 Click on Save for Interface 1 and Save for Interface 2. Save (green button) then quit Game Engine and game manager (see under)
4 Launch the game engine and normally if all is right the 5 actuators should move. If the actuators don t move, see if you have powered the actuators, the 5 small box in grey colour (aluminium) must have green led. Do you put the power supply? Remove power cable, wait 10 seconds and put another time power cable. Verify that you have correctly filled the Interface 1 and interface 2. Restart the game engine and the 5 actuators must move, if not, contact us.
5
6 Take a paper and pen Go to Output testing -> axis testing then click on Turn On and select Axis Output (under Output Type). Move slowly the Axis 1 and verify that your right front actuators move, if it s the wrong actuator, you must write on your paper the actuator (interface) that move. Instead. Move slowly the Axis 2 and verify that your left front actuators move, if it s the wrong actuator, you must write on your paper the actuator (interface) that move. Instead. Move slowly the Axis 3 and verify that your rear right actuators move, if it s the wrong actuator, you must write on your paper the actuator (interface) that move. Instead. Move slowly the Axis 4 and verify that your rear left actuators move, if it s the wrong actuator, you must write on your paper the actuator (interface) that move. Instead. Move slowly the Axis 5 and verify that your 5 actuators move, if it s the wrong actuator, you must write on your paper the actuator (interface) that move. Instead.
7 1-Click turn Off. 2-Go to Interface settings and change/put the good Assigned Axis for each interface 1,2,3,4,5. Use your paper notes for this. 3- Verify that you have only once Axis 1, Axis 2, Axis 3, Axis4, Axis 5 for each interface settings 4- Press save for each Interface settings
8 Go a second time to Output testing -> axis testing then click on Turn On and select Axis Output (under Output Type). Move slowly the Axis 1 and verify that your right front actuators move, if it s the wrong actuator, you must write on your paper the actuator that move. Instead. Move slowly the Axis 2 and verify that your left front actuators move, if it s the wrong actuator, you must write on your paper the actuator that move. Instead. Move slowly the Axis 3 and verify that your rear right actuators move, if it s the wrong actuator, you must write on your paper the actuator that move. Instead. Move slowly the Axis 4 and verify that your rear left actuators move, if it s the wrong actuator, you must write on your paper the actuator that move. Instead. Move slowly the Axis 5 and verify that your 5 actuators move, if it s the wrong actuator, you must write on your paper the actuator that move. Instead. This settings is very important in order to have a good simulation experience with the profile below
9 Re-launch game manager and game engine, the 5 actuators must move. Go to axis assignment -> axis limiting and put axis 1 & 2 & 3 &4 & 5 to 90%. it s the software limitation of the actuators then save settings
10 Go to axis assignement -> axis Assignement and fill the default profil (Under Game List) for DOF1 to DOF5 : it s the force repartition between the 5 actuators. And save settings
11 Heave, surge et sway : it s force for the vehicle movement. Heave : when the car jump under bump Surge : acceleration and braking Sway : right and left turn. Roll, Pitch, et Yaw : it s force for the tilt of the road Pitch : when the road ascend and descend Roll : when the road lean to the right /left Yaw : when the road turn Extra1 : use for the traction loss only with 3 and 5 actuators. If you have 3 actuators, filled like this : The Default profil is very important, each time you will add a new games, the default profil will be used and copy to your new games profile. Do a save settings when you have finished. You could modify the Default profil or the profil of you game (under Game list), remember that you must Save at the end. When you will play with your New game (later in the documentation), you must verify the different point (stop the game and change value if necessary) : If you feel that the force: - Acceleration braking (Surge) are inversed : just color (or uncolored) the 2 orange square (Axis1 &2) - Right and left turn (Sway) are inversed : just color (or uncolored) the axis 1 and uncolored (or colored) the axis 2 : the 2 axis must be opposed in orange colored. - road ascend and you feel descend (pitch) : just uncolored (or colored) the 2 axis -road tilt to the right and you feel left (Roll) : just color (or uncolored) the axis 1 and uncolored (or colored) the axis 2 : the 2 axis must be opposed in orange colored.
12 Remember to Save Settings with the good games! Add a new game Close Game Manager and Game Engine Download the plugin of your game on X-Simulator.net or Launch SimToolsPluginUpdater (start->all Programs->Simtools-> SimToolsPluginUpdater or C:\Program Files (x86)\simtools)
13 Drag and drop the plugin (with zip) inside the GamePluginUpdater. Close GamePluginUpdater. Launch the game engine and notice that your default profil has been copied inside the Rfactor profil (under Axis assignements-> Axis assignements -> Game List)
14 Launch the Game manager, select your game (here Rfactor) click on Patching then Edit path Notice : For patching some games, you need to launch the Game manager in administrator mode : just click right to the game manager icon and select Run as administrator )
15 For codemasters games ( DIRT, GRID F12010,11,12,13,14... ) you have to patch the My Documents / my games / Your codemasters games. For other games ( not Codemaster ), go generally in the installation directory of the game or steam directory installation games. The game under steam are here : C:\Program Files (x86)\steam\steamapps\common\ your game or here your drive :\SteamLibrary\steamapps\common
16
17 Click on Patch Game
18
19 If you want to install a new plugin for the same game, you must remove the old plugin before doing this.
20 Game Manager Go to game manager - > profile editor The main level is very important: during the game, you could tune the feeling of the 2 actuators! Do a pause of your game and change to or 85%, you will notice a big change between these 3 values. The actuators will react with more or less smooth movement.
21
22
23 You could change (during the game do a pause) the force of the vehicle and effect of the road. When you increase the forces: the actuators rod end will have a bigger movement (more amplitude). Heave, surge et sway : it s force for the vehicle movement. Heave : when the car jump under bump Surge : acceleration and braking Sway : right and left turn. Roll, Pitch, et Yaw : it s force for the tilt of the road Pitch : when the road ascend and descend Roll : when the road lean to the right /left Yaw : when the road If you want to feel more forces of the vehicle -> increase the Heave, surge, sway and reduce the pitch roll yaw. Tune a force one by one and do test inside the game. If you want to feel the effect of the road -> do the opposite above. If you want to feel more of all forces : increase all the forces.
24 You could save several profil with profil editor, just copy and name a new profil, then you could create new profil. It s auto-save.
25 For each new game : the telemetry is not very accurate, you need to use the Tuning center : it will recalibrate the telemetry min, max and send good telemetry to the actuators. (right click on GameEngine) Click on capture MinMax, then reset, then drive your car as fast as possible during 1 lap without any crashes and with acceleration, braking, turn to the left, right..
26 When you have finished : click on Save Settings then Stop capture. After this, reload your track and drive your car, the feeling must be very accurate. Tips When game manager is alone Not Connected in red
27 When Game manager and game engine are launching Connected in green When the telemetry data of the game are well detected Game running in blue
28 COM port changing Go to Start> Configuration Panel> Système> Device manager->com LPT
29 Change the number of the COM port to 3 and 4 and save then restart the PC.
Make sure you have any plugins saved separately in a different folder.
How to set up simulator Heres a guide to get you going with Simtools 1.2 Make sure you have any plugins saved separately in a different folder. Uninstall Simtools 3.1 and remove all settings. Restart PC.
More informationSimCraft Control Panel CraftCon Usage Manual
SimCraft Control Panel CraftCon Usage Manual Published Date October 2, 2007 Revision Date October 8th, 2013 Revision Date February 1st, 2014 Revision Date May 8 th, 2017 Revision Date July 9 th, 2018 Revision
More informationStuduino Icon Programming Environment Guide
Studuino Icon Programming Environment Guide Ver 0.9.6 4/17/2014 This manual introduces the Studuino Software environment. As the Studuino programming environment develops, these instructions may be edited
More informationPWM P108. Programming Instructions v 3.2 PWM Controller Software
PWM P108 Programming Instructions v 3.2 PWM Controller Software PWM P108 Programming Instructions v 3.2 for PWM Controller Software Download / Install & Run Driver (Must be installed for software to work)
More informationOmniverse Setup Instructions
Omniverse Setup Instructions Hello Omni customer, Please follow the steps outlined below to get your Omni ready for Omniverse! Let us know if you have questions or issues at any time at support@virtuix.com.
More informationDXXX Series Servo Programming...9 Introduction...9 Connections HSB-9XXX Series Servo Programming...19 Introduction...19 Connections...
DPC-11 Operation Manual Table of Contents Section 1 Introduction...2 Section 2 Installation...4 Software Installation...4 Driver Installastion...7 Section 3 Operation...9 D Series Servo Programming...9
More informationTable of Contents. Chapter 1: Software Installation...1. Chapter 2: Running the Software II. Daily Practical Operation...10
Product Manual Table of Contents Chapter 1: Software Installation.................................1 Chapter 2: Running the Software............................... 2 I. The Initial Defining in Lock Management
More informationMBC DG GUI MBC INTERFACE
MBC DG GUI MBC INTERFACE User Manual Version 2.6 Table des matières Interface - Introduction... 3 Interface - Setup... 3 Minimum Computer Requirements... 3 Software installation... 3 Hardware Setup...
More informationIssue No: MG025 Date: 05 June McMurdo SmartFind R5 GMDSS Radio IMO MSC. 1/Circ Update procedure
Installation SERVICE BULLETIN Issue No: MG025 Date: 05 June 2017 McMurdo SmartFind R5 GMDSS Radio IMO MSC. 1/Circ. 1460 Update procedure Product Affected: McMurdo R5 GMDSS VHF Handheld Radio Reason: Compliance
More information1. ASSEMBLING THE PCB 2. FLASH THE ZIP LEDs 3. BUILDING THE WHEELS
V1.0 :MOVE The Kitronik :MOVE mini for the BBC micro:bit provides an introduction to robotics. The :MOVE mini is a 2 wheeled robot, suitable for both remote control and autonomous operation. A range of
More informationHandbook. Antenna Rotator Controller
Handbook Controller 3S design GmbH 2. Südwieke 231 26817 Rhauderfehn Germany www.3sdesign.de Tel. +49-4952-921950 Contents I Table of content Part I 1 1 Operating... 1 2 Installation... 2 1 1 1.1 Operating
More informationTel & Fax : Install and Operate Sharp Shape USB3D Foot Scanner Copyright, Sharp Shape, July 2014
12891 Lantana Ave. Saratoga, CA 95070 Sharp Shape not just any shape www.sharpshape.com Tel & Fax : 408-871-1798 Install and Operate Sharp Shape USB3D Foot Scanner Copyright, Sharp Shape, July 2014 The
More informationThe SilverLink 5. For Silver Reed & Knitmaster electronic machines
The SilverLink 5 For Silver Reed & Knitmaster electronic machines This cable link enables DesignaKnit to control interactive knitting on the Silver Reed modular electronic knitting machines SK830, SK840,
More informationsmraza Getting Start Guide Contents Arduino IDE (Integrated Development Environment)... 1 Introduction... 1 Install the Arduino Software (IDE)...
Getting Start Guide Contents Arduino IDE (Integrated Development Environment)... 1 Introduction... 1 Install the Arduino Software (IDE)...1 Introduction... 1 Step 1: Get an Uno R3 and USB cable... 2 Step
More informationThe quantitative relationship between distance, time and speed
The quantitative relationship between distance, time and speed Introduction In order to understand motion, it is important to consider the basic definition in terms of distance and time. When we say a
More informationIMU: Get started with Arduino and the MPU 6050 Sensor!
1 of 5 16-3-2017 15:17 IMU Interfacing Tutorial: Get started with Arduino and the MPU 6050 Sensor! By Arvind Sanjeev, Founder of DIY Hacking Arduino MPU 6050 Setup In this post, I will be reviewing a few
More informationMomo Software Context Aware User Interface Application USER MANUAL. Burak Kerim AKKUŞ Ender BULUT Hüseyin Can DOĞAN
Momo Software Context Aware User Interface Application USER MANUAL Burak Kerim AKKUŞ Ender BULUT Hüseyin Can DOĞAN 1. How to Install All the sources and the applications of our project is developed using
More informationA MANUAL FOR FORCECONTROL 4.
A MANUAL FOR 4. TABLE OF CONTENTS 3 MAIN SCREEN 3 CONNECTION 6 DEBUG 8 LOG 9 SCALING 11 QUICK RUN 14 Note: Most Force Dynamics systems, including all 301s and all 401cr models, can run ForceControl 5.
More informationA3 Pro INSTRUCTION MANUAL. Oct 25, 2017 Revision IMPORTANT NOTES
A3 Pro INSTRUCTION MANUAL Oct 25, 2017 Revision IMPORTANT NOTES 1. Radio controlled (R/C) models are not toys! The propellers rotate at high speed and pose potential risk. They may cause severe injury
More information2020 DRAWBOT INSTALLATION AND USE. Robert Ashford Henry Arnold 4-H OABB
2020 DRAWBOT INSTALLATION AND USE Robert Ashford Henry Arnold 4-H OABB 2020 DrawBot Software If you are viewing this document, you probably just finished assembling your 2020 DrawBot. In order to use your
More informationHTC VIVE Installation Guide
HTC VIVE Installation Guide Thank you for renting from Hartford Technology Rental. Get ready for an amazing experience. To help you setup the VIVE, we highly recommend you follow the steps below. Please
More informationHow2 create your first world in Kodu
How2 create your first world in Kodu When you open Kodu Game Lab, you will see a window that has a number of options. To create your own world in Kodu, select New World. A new window will open with a patch
More informationVinyl Cutter Instruction Manual
Vinyl Cutter Instruction Manual 1 Product Inventory Inventory Here is a list of items you will receive with your vinyl cutter: Product components (Fig.1-4): 1x Cutter head unit complete with motor, plastic
More informationOperating Manual. itech IMPAXX Digital Monument Engraver
Operating Manual itech IMPAXX Digital Monument Engraver Copyright 2013 Allen Datagraph Systems - All Rights Reserved Manual Date August 2013 Congratulations on your new purchase! Thank You for Selecting
More informationInstruction Manual. Ultrasonic and Radar
Instruction Manual ABM Gateway Software for 3 & 4 wire Ultrasonic and Radar Instruction Manual Revision 5.8 NOTE: Windows 7 and 8 users are asked to use default screen size (100%). To change from Larger
More informationThe ideal K-12 science microscope solution. User Guide. for use with the Nova5000
The ideal K-12 science microscope solution User Guide for use with the Nova5000 NovaScope User Guide Information in this document is subject to change without notice. 2009 Fourier Systems Ltd. All rights
More informationIntroduction. Overview. Outputs Normal model 4 Delta wing (Elevon) & Flying wing & V-tail 4. Rx states
Introduction Thank you for purchasing FrSky S6R/S8R (SxR instead in this manual) multi-function telemetry receiver. Equipped with build-in 3-axis gyroscope and accelerometer, SxR supports various functions.
More informationName: First-Order Response: RC Networks Objective: To gain experience with first-order response of RC circuits
First-Order Response: RC Networks Objective: To gain experience with first-order response of RC circuits Table of Contents: Pre-Lab Assignment 2 Background 2 National Instruments MyDAQ 2 Resistors 3 Capacitors
More informationDPC-10. DPC-10 Software Operating Manual. Table of Contents. Section 1. Section 2. Section 3. Section 4. Section 5
Table of Contents Section 1 Section 2 Section 3 Section 4 Section 5 About the Software Test Function Programming Functions Connections Basic Mode Connection RC Mode Connection Using the DPC-10 Test Functions
More informationSoftware Club 402: Create THREAD VELVET Embroidery
Software Club 402: Create THREAD VELVET Embroidery By Janie Lantz, Embroidery Software Specialist Create THREAD VELVET embroidery with its unique velvety plush texture, using 5D Design Creator in the 5D
More informationThe DesignaKnit USB E6000 Link 1 & 2
The DesignaKnit USB E6000 Link 1 & 2 for the Passap / Pfaff Electronic 6000 USB E6000 Link 1 USB E6000 Link 2 What these links do The USB E6000 Link 1 enables downloading of stitch patterns from DesignaKnit
More informationQuick Start Guide for the PULSE PROFILING APPLICATION
Quick Start Guide for the PULSE PROFILING APPLICATION MODEL LB480A Revision: Preliminary 02/05/09 1 1. Introduction This document provides information to install and quickly start using your PowerSensor+.
More informationHead Tracker Range Checking
Head Tracker Range Checking System Components Haptic Arm IR Transmitter Transmitter Screen Keyboard & Mouse 3D Glasses Remote Control Logitech Hardware Haptic Arm Power Supply Stand By button Procedure
More informationDMMDRV 2017 Software User Manual. Version: A1324 / December 2017 Manual Code: DSFEN A
DMMDRV 2017 Software User Manual Version: A1324 / December 2017 Manual Code: DSFEN A1324 1217 Contents Section 1. General Software Safety Precautions 1.1 DYN2 System Safety 1.2 DYN4 System Safety 1.3 Servo
More informationFLL Programming Workshop Series
FLL Programming 2017 Workshop Series 2017 1 Prerequisites & Equipment Required Basic computer skills Assembled EV3 Educational robot or equivalent Computer or Laptop with LEGO Mindstorms software installed
More informationA3 SUPER 3 INSTRUCTION MANUAL. For Firmware Version 1.0, Data Version 1.0 Oct 25, 2017 Revision.
A3 SUPER 3 INSTRUCTION MANUAL For Firmware Version 1.0, Data Version 1.0 Oct 25, 2017 Revision support@hobbyeagle.com 1 CONTENTS IMPORTANT NOTES.....3 1. Introduction......4 2. Setup Procedure Overview...5
More informationLegacy FamilySearch Overview
Legacy FamilySearch Overview Legacy Family Tree is "Tree Share" Certified for FamilySearch Family Tree. This means you can now share your Legacy information with FamilySearch Family Tree and of course
More informationSWI-CP5. Universal Steering Wheel Control Retention Interface. Steering Wheel Control Interface. Introduction and Features.
SWI-CP5 Universal Steering Wheel Control Retention Interface Introduction and Features The SWI-CP5 interface allows the retention of steering wheel controls (SWC), rear seat controls (RSC) and retained
More informationPhysical Inventory System User Manual. Version 19
Physical Inventory System User Manual Version 19 0 Physical Inventory System User Manual 1 Table of Contents 1. Prepare for Physical Inventory... 2. Chapter 1: Starting Inventory... 2.1. CDK/ADP... 3.
More informationVirtual Flight Academy - Quick Start Guide
Virtual Flight Academy - Quick Start Guide Ready to get started learning to fly or maintaining proficiency? EAA Virtual Flight Academy will help you build the confidence and competence to get it done!
More informationInsight VCS: Maya User s Guide
Insight VCS: Maya User s Guide Version 1.2 April 8, 2011 NaturalPoint Corporation 33872 SE Eastgate Circle Corvallis OR 97339 Copyright 2011 NaturalPoint Corporation. All rights reserved. NaturalPoint
More informationSDA100 Software Release Mustang **** Preliminary ****
SDA100 Software Release Mustang **** Preliminary **** 12/20/16 Mustang Firmware User's Guide (Release 1304150051) Page 1 Table of Contents Purpose... 3 Release History... 3 Theory... 4 Operate Mode...
More informationIntroduction to the Analog Discovery
Introduction to the Analog Discovery The Analog Discovery from Digilent (http://store.digilentinc.com/all-products/scopes-instruments) is a versatile and powerful USB-connected instrument that lets you
More informationQUICK SETUP GUIDE: Firewire/mLAN MACINTOSH OSX Cubase AI4 / Studio Manager / Motif XS Editor / Mac OSX
QUICK SETUP GUIDE: Firewire/mLAN MACINTOSH OSX Cubase AI4 / Studio Manager / Motif XS Editor / Mac OSX Install Install Cubase AI4 on your Mac. Update to the latest version at www.steinberg.net Download
More informationChanalyzer Lab. Chanalyzer Lab by MetaGeek USER GUIDE page 1
Chanalyzer Lab Chanalyzer Lab by MetaGeek USER GUIDE page 1 Chanalyzer Lab spectrum analysis software Table of Contents Control Your Wi-Spy What is a Wi-Spy? What is Chanalyzer Lab? Installation 1) Download
More informationDMMDRV Software User Manual. Version: A10 50 / December 2015 Manual Code: DSFEN A
DMMDRV Software User Manual Version: A10 50 / December 2015 Manual Code: DSFEN A1050 1215 Contents Section 1. General Software Safety Precautions 1.1 DYN2 System Safety 1.2 DYN4 System Safety 1.3 Servo
More informationMidi Fighter 3D. User Guide DJTECHTOOLS.COM. Ver 1.03
Midi Fighter 3D User Guide DJTECHTOOLS.COM Ver 1.03 Introduction This user guide is split in two parts, first covering the Midi Fighter 3D hardware, then the second covering the Midi Fighter Utility and
More informationGetting Started with EAA Virtual Flight Academy
Getting Started with EAA Virtual Flight Academy What is EAA Virtual Flight Academy? Imagine having a Virtual Flight Instructor in your home or hangar that you could sit down and get quality flight instruction
More informationGXCapture 8.1 Instruction Manual
GT Vision image acquisition, managing and processing software GXCapture 8.1 Instruction Manual Contents of the Instruction Manual GXC is the shortened name used for GXCapture Square brackets are used to
More informationAn Escape Room set in the world of Assassin s Creed Origins. Content
An Escape Room set in the world of Assassin s Creed Origins Content Version Number 2496 How to install your Escape the Lost Pyramid Experience Goto Page 3 How to install the Sphinx Operator and Loader
More informationLego Nxt in Physical Etoys
Lego Nxt in Physical Etoys Physical Etoys is a software Project which let us control, in real time, Lego Mindstorms Nxt s Robots using a Bluetooth connection. SqueakNxt is a module of the Physical Etoys
More informationActivity 1 Position, Velocity, Acceleration PHYS 010
Name: Date: Partners: Purpose: To investigate and analyse basic properties of motion using a Vernier Go! Motion Detector and logging software. Materials: 1. PC with Logger Lite Software installed. 2. Go!
More informationWhite Balance and Colour Calibration Workflow in Photoshop with the X -Rite ColorChecker Passport
White Balance and Colour Calibration Workflow in Photoshop with the X -Rite ColorChecker Passport White Balance an the Temperature of Light One of the basic ways of controlling colour when we are taking
More informationTopcon Receiver Utility: GNSS Receiver Firmware Update Process. Oscar R. Cantu
Topcon Receiver Utility: GNSS Receiver Firmware Update Process Oscar R. Cantu TRU: GNSS Receiver Firmware Update Topcon Receiver Utility (TRU), product definition Office Processing and Reporting Software
More informationOculus Rift Getting Started Guide
Oculus Rift Getting Started Guide Version 1.23 2 Introduction Oculus Rift Copyrights and Trademarks 2017 Oculus VR, LLC. All Rights Reserved. OCULUS VR, OCULUS, and RIFT are trademarks of Oculus VR, LLC.
More informationJEOL 6500 User Manual
LOG IN to your session on the computer to the left of the microscope. Starting Conditions 1. Press Ctrl-Alt-Del and log on to the microscope computer. Click on JEOL PC SEM 6500 icon. Click yes if message
More information2.2 Laser Etching with BoXZY. This manual will get you started laser etching with BoXZY. Written By: BoXZY boxzy.dozuki.
2.2 Laser Etching with BoXZY This manual will get you started laser etching with BoXZY. Written By: BoXZY 2018 boxzy.dozuki.com/ Page 1 of 18 INTRODUCTION This manual will guide you through a two-part
More informationPractical Assignment 1: Arduino interface with Simulink
!! Department of Electrical Engineering Indian Institute of Technology Dharwad EE 303: Control Systems Practical Assignment - 1 Adapted from Take Home Labs, Oklahoma State University Practical Assignment
More informationLab book. Exploring Robotics (CORC3303)
Lab book Exploring Robotics (CORC3303) Dept of Computer and Information Science Brooklyn College of the City University of New York updated: Fall 2011 / Professor Elizabeth Sklar UNIT A Lab, part 1 : Robot
More informationMini Hexapodinno. 18-DOF Robot
Mini Hexapodinno 18-DOF Robot Instruction Manual Version 1.11 Trademark Innovati,, and BASIC Commander, are registered trademarks of Innovati Inc. InnoBASIC and cmdbus are trademarks of Innovati Inc. Copyright
More informationLet s start by making a pencil that can be used to draw on the stage.
Paint Box Introduction In this project, you will be making your own paint program! Step 1: Making a pencil Let s start by making a pencil that can be used to draw on the stage. Activity Checklist Open
More informationPiezo Driver MTAD4002
Piezo Driver MTAD002 Instruction Manual Contents. Overview 2 2. List of contents 2 3. Specifications 2~3. Operation 3~. Signal Generation Software ~3. Precautions 3 Published on th Sept 20 Overview Piezo
More informationRecording your Voice Tutorials 2 - Setting the Computer Setting Audacity Wayne B. Dickerson
Recording your Voice Tutorials 2 - Setting the Computer Setting Audacity Wayne B. Dickerson In this tutorial we want to insure that your computer and Audacity will do the best recording job they can do
More informationAn Introduction to Programming using the NXT Robot:
An Introduction to Programming using the NXT Robot: exploring the LEGO MINDSTORMS Common palette. Student Workbook for independent learners and small groups The following tasks have been completed by:
More informationHandbook for the Starlight Xpress AO unit Issue 1 21/8/2005 Handbook for the Starlight Xpress SXV-AO unit
Handbook for the Starlight Xpress SXV-AO unit Thank you for purchasing an SXV-AO active optics unit. This device should give you much improved guiding accuracy with almost any telescope and mount. Please
More informationOculus Rift Getting Started Guide
Oculus Rift Getting Started Guide Version 1.7.0 2 Introduction Oculus Rift Copyrights and Trademarks 2017 Oculus VR, LLC. All Rights Reserved. OCULUS VR, OCULUS, and RIFT are trademarks of Oculus VR, LLC.
More information1 Overview Introduction Acronyms & abbreviations...2
Revision A, January 2018 Antenna Sharing Configuration using CommScope RET Controller Systems Table of Contents 1 Overview...2 1.1 Introduction...2 1.2 Acronyms & abbreviations...2 2 Antenna Sharing Configuration
More informationIX Feb Operation Guide. Sequence Creation and Control Software SD011-PCR-LE. Wavy for PCR-LE. Ver. 5.5x
IX000693 Feb. 015 Operation Guide Sequence Creation and Control Software SD011-PCR-LE Wavy for PCR-LE Ver. 5.5x About This Guide This PDF version of the operation guide is provided so that you can print
More informationIVCAD VNA Base Load Pull with Active/Hybrid Tuning. Getting Started v3.5
IVCAD VNA Base Load Pull with Active/Hybrid Tuning Getting Started v3.5 1 Setting and Configuration Block Diagram... 3 1.1 VNA setup... 5 1.2 RF source setup... 6 1.3 Power meter setup... 7 1.4 Source
More informationUsing CME 2 with AccelNet
Using CME 2 with AccelNet Software Installation Quick Copy (with Amplifier file) Quick Setup (with motor data) Offline Virtual Amplifier (with no amplifier connected) Screen Guide Page 1 Table of Contents
More informationThe DesignaKnit USB Brotherlink 3
The DesignaKnit USB Brotherlink 3 For the Brother PPD What this link does Uploading and downloading patterns between DesignaKnit and a PPD cartridge in the modes for KH270, KH930, KH940, KH950i, KH965,
More informationMinolta Scanner Plugin
Minolta Scanner Plugin For a list of Minolta digitizers and Geomagic software products with which this plugin is compatible, see Release Notes for Geomagic Minolta Plugin 7.6.0.3. Copyright 2005, Raindrop
More informationTEMScripts Auto Image Measurement (Particle) Manual. TEMScripts LLC. Last updated: 12/5/2016
TEMScripts Auto Image Measurement (Particle) Manual TEMScripts LLC. Last updated: 12/5/2016 TS Auto Image Measurement- Particle Installation Close Digital Micrograph Copy following files to \\Gatan\DigitalMicrograph\PlugIns
More informationUser Manual Version 1.0
1 Thank you for purchasing our products. The A3 Pro SE controller is the updated version of A3 Pro. After a fully improvement and optimization of hardware and software, we make it lighter, smaller and
More informationTable of Contents. Vizit s Carousel Menu Gallery Play Favorite Remove Rotate Fill Screen Friends Block Lock Screen Settings Reply Share
User Guide Table of Contents VIZIT, VIZITME.COM, VIZIT SEE.TOUCH.FEEL, and the Vizit logo are trademarks and/or registered trademarks of Isabella Products, Inc. Other marks are owned by their respective
More informationMobile Application Training
Mobile Application Training NPMStaffing.com Ready to Work on Your Terms? At NPM Staffing, your next job is now at your fingertips. Our mobile application is easy to use and allows you to work when you
More informationAnalog Discovery Arbitrary Function Generator for Windows 7 by Mr. David Fritz and Ms. Ellen Robertson
Analog Discovery Arbitrary Function Generator for Windows 7 by Mr. David Fritz and Ms. Ellen Robertson Financial support to develop this tutorial was provided by the Bradley Department of Electrical and
More informationAbout the DSR Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
About the DSR 100-15 Dropout, Surge, Ripple Simulator and AC/DC Voltage Source Congratulations on your purchase of a DSR 100-15 AE Techron dropout, surge, ripple simulator and AC/DC voltage source. The
More informationObjective Motion Cueing Test for Driving Simulators
DLR.de Chart 1 Objective Motion Cueing Test for Driving Simulators Martin Fischer, Andreas Seefried, Carsten Seehof DLR.de Chart 2 Looking in the rear mirror Is your simulator appropriate for my research?
More informationManually Save Gta Iv Pc Game Location Windows
Manually Save Gta Iv Pc Game Location Windows 7 Grand Theft Auto IV, 2008 2.1 Configuration file(s) location, 2.2 Save game data location, 2.3 Save game cloud syncing 7 VR support, 8 Issues unresolved
More informationDetrum MSR66A Receiver
Motion RC User Guide for the Detrum MSR66A Receiver Version 1.0 Contents Review the Receiver s Features... 1 Review the Receiver s Ports and Connection Orientation... 2 Bind the Receiver to a Transmitter
More informationApplication Note. Communication between arduino and IMU Software capturing the data
Application Note Communication between arduino and IMU Software capturing the data ECE 480 Team 8 Chenli Yuan Presentation Prep Date: April 8, 2013 Executive Summary In summary, this application note is
More informationStart Here. Installing your Microtek ScanMaker i280
Start Here Installing your Microtek ScanMaker i280 Step 1: Unpack Contents Unpack your scanner package and check for major components. 1. ScanMaker i280 scanner 2. Hi-Speed USB cable 3. Software CDs/DVDs
More informationSWI-CP5 Universal Steering Wheel Control Retention Interface
Introduction & Features The interface allows the retention of steering wheel controls (SWC), rear seat controls (RSC) and retained accessory power (RAP) whenever replacing a factory radio. Use of this
More informationKongsberg Seatex AS Pirsenteret N-7462 Trondheim Norway POSITION 303 VELOCITY 900 HEADING 910 ATTITUDE 413 HEAVE 888
WinFrog Device Group: Device Name/Model: Device Manufacturer: Device Data String(s) Output to WinFrog: WinFrog Data String(s) Output to Device: WinFrog Data Item(s) and their RAW record: GPS SEAPATH Kongsberg
More informationLPR SETUP AND FIELD INSTALLATION GUIDE
LPR SETUP AND FIELD INSTALLATION GUIDE Updated: May 1, 2010 This document was created to benchmark the settings and tools needed to successfully deploy LPR with the ipconfigure s ESM 5.1 (and subsequent
More informationCAUTION DO NOT ATTEMPT TO ALTER THE TUNING OF THE RADIO EQUIPMENT. DO NOT USE RADIO CONTROL EQUIPMENT IN THUNDERSTORMS.
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com TX-5vL Digital Proportional R/C TABLE OF CONTENTS
More informationMIST A Musical Interactive Space for Therapy
MIST A Musical Interactive Space for Therapy INSTRUCTION MANUAL 1.0 GENERAL INFORMATION 1.1 System Overview The software runs on Mac requires 2 GB RAM and 500 MB of available disc space. A Microsoft Kinect
More informationSpellodrome Student Console
Spellodrome Student Console A guide to using the Spellodrome learning space Spellodrome is a captivating space which provides learners with all the tools they need to be successful, both in the classroom
More informationCreo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
More informationSubmittals Quick Reference Guide
This topic provides a reference for the Project Center Submittals activity center. Purpose The Submittals activity center in Newforma Contract Management enables you to effectively log submittals and track
More informationCONCEPTS EXPLAINED CONCEPTS (IN ORDER)
CONCEPTS EXPLAINED This reference is a companion to the Tutorials for the purpose of providing deeper explanations of concepts related to game designing and building. This reference will be updated with
More informationEasy Input Helper Documentation
Easy Input Helper Documentation Introduction Easy Input Helper makes supporting input for the new Apple TV a breeze. Whether you want support for the siri remote or mfi controllers, everything that is
More informationCONTENTS INTRODUCTION ACTIVATING VCA LICENSE CONFIGURATION...
VCA VCA Installation and Configuration manual 2 Contents CONTENTS... 2 1 INTRODUCTION... 3 2 ACTIVATING VCA LICENSE... 6 3 CONFIGURATION... 10 3.1 VCA... 10 3.1.1 Camera Parameters... 11 3.1.2 VCA Parameters...
More informationHARDWARE SETUP GUIDE. 1 P age
HARDWARE SETUP GUIDE 1 P age INTRODUCTION Welcome to Fundamental Surgery TM the home of innovative Virtual Reality surgical simulations with haptic feedback delivered on low-cost hardware. You will shortly
More informationLab 7: Introduction to Webots and Sensor Modeling
Lab 7: Introduction to Webots and Sensor Modeling This laboratory requires the following software: Webots simulator C development tools (gcc, make, etc.) The laboratory duration is approximately two hours.
More informationSKF TKTI. Thermal Camera Software. Instructions for use
SKF TKTI Thermal Camera Software Instructions for use Table of contents 1. Introduction...4 1.1 Installing and starting the Software... 5 2. Usage Notes...6 3. Image Properties...7 3.1 Loading images
More informationGetting Started. Right click on Lateral Workplane. Left Click on New Sketch
Getting Started 1. Open up PTC Pro/Desktop by either double clicking the icon or through the Start button and in Programs. 2. Once Pro/Desktop is open select File > New > Design 3. Close the Pallet window
More informationLEGO Mindstorms Class: Lesson 1
LEGO Mindstorms Class: Lesson 1 Some Important LEGO Mindstorm Parts Brick Ultrasonic Sensor Light Sensor Touch Sensor Color Sensor Motor Gears Axle Straight Beam Angled Beam Cable 1 The NXT-G Programming
More informationJoneSoft Generic Mod Enabler v2.6
JoneSoft Generic Mod Enabler v2.6 User Guide 8 August 2010 Contents Introduction... 2 Installation... 3 1. Central installation... 3 2. Separate installation... 4 Installing over an existing installation...
More information