TEST REPORT. For ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED EN V9.0.2 ( )

Transcription

1 TEST REPORT For ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED No.161, Xin Min Road, Tong Luo Wei Industrial Zone, Jin Xia, Chang An Town, Dong Guan City, Guang Dong Province, China EN V9.0.2 ( ) Model: M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD-05, MDT501, TP501, MDT511, TP511 Report Type: Original Report Product Type: GPS Test Engineer: Report Number: Jimmy Xiao RSZ Report Date: Merry Zhao Reviewed By: Test Laboratory: EMC Engineer Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: Fax: Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk (Rev.2)

2 TABLE OF CONTENTS GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 RELATED SUBMITTAL(S)/GRANT(S)... 4 TEST METHODOLOGY... 5 TEST FACILITY... 5 SYSTEM TEST CONFIGURATION... 6 JUSTIFICATION... 6 EUT EXERCISE SOFTWARE... 6 SPECIAL ACCESSORIES... 6 EQUIPMENT MODIFICATIONS... 6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS... 6 EXTERNAL I/O CABLE... 6 CONFIGURATION OF TEST SETUP... 7 BLOCK DIAGRAM OF TEST SETUP... 7 SUMMARY OF TEST REPORT RADIATED SPURIOUS EMISSIONS MS ALLOCATED A CHANNEL... 9 APPLICABLE STANDARD... 9 TEST PROCEDURE... 9 TEST EQUIPMENT ENVIRONMENTAL CONDITIONS TEST RESULTS RADIATED SPURIOUS EMISSIONS MS IN IDLE MODE APPLICABLE STANDARD TEST PROCEDURE TEST EQUIPMENT ENVIRONMENTAL CONDITIONS TEST RESULTS EXHIBIT A - CE PRODUCT LABELING PROPOSED CE LABEL FORMAT PROPOSED LABEL LOCATION ON EUT EXHIBIT B - EUT PHOTOGRAPHS EUT FRONT VIEW EUT REAR VIEW EUT TOP VIEW EUT BOTTOM VIEW EUT LEFT SIDE VIEW EUT RIGHT SIDE VIEW EUT UNCOVER VIEW EUT MAIN BOARD WITH SHIELD TOP VIEW EUT MAIN BOARD WITH SHIELD OFF TOP VIEW EUT MAIN BOARD WITH SHIELD OFF TOP VIEW EUT MAIN BOARD WITH SHIELD BOTTOM VIEW EUT MAIN BOARD WITH SHIELD OFF BOTTOM VIEW Report No.: RSZ Page 2 of 39 EN V9.0.2 Test Report

3 EUT LCD TOP VIEW EUT LCD BOTTOM VIEW EUT GPRS MODULE WITH SHIELD TOP VIEW EUT GPRS MODULE WITH SHIELD OFF TOP VIEW EUT GPRS MODULE BOTTOM VIEW EUT GPS MODULE WITH SHIELD TOP VIEW EUT GPS MODULE WITH SHIELD OFF TOP VIEW EUT GPS MODULE BOTTOM VIEW EUT BLUETOOTH ANTENNA VIEW EUT GSM ANTENNA VIEW EUT GSM ANTENNA LOCATION VIEW EUT WIFI ANTENNA TOP VIEW EUT WIFI ANTENNA BOTTOM VIEW EUT ACCESSORY VIEW EUT BATTERY TOP VIEW EUT BATTERY BOTTOM VIEW EUT ADAPTER VIEW EUT ADAPTER INFORMATION VIEW EUT ADAPTER UNCOVERVIEW EUT ADAPTER MAIN BOARD TOP VIEW EUT ADAPTER MAIN BOARD BOTTOM VIEW EXHIBIT C - TEST SETUP PHOTOGRAPHS RADIATED EMISSIONS - FRONT VIEW (BELOW 1 GHZ) RADIATED EMISSIONS - REAR VIEW (BELOW 1 GHZ) RADIATED EMISSIONS - FRONT VIEW (ABOVE 1 GHZ) RADIATED EMISSIONS - REAR VIEW (ABOVE 1 GHZ) PRODUCT SIMILARITY DECLARATION LETTER Report No.: RSZ Page 3 of 39 EN V9.0.2 Test Report

4 GENERAL INFORMATION Product Description for Equipment under Test (EUT) The ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED s product, model number: E500 or the "EUT" as referred to in this report is a GPS, which measures approximately: 14.9 cm (L) x 9.7 cm (W) x 2.3 cm (H), rated input voltage: DC 3.7 V Battery or DC 12-24V power source. Car adapter information: Model: SW A; Input: DC 12-24V 2.5A; Output: DC 5V/2A *Note: The serial product model M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD-05, MDT501, TP501, MDT511, TP511, all the models are electrically identical, only their difference is model name, and we select model E500 for the testing in this report, which was explained in the attached declaration letter. * All measurement and test data in this report was gathered from production sample serial number: (Assigned by Shenzhen BACL). The EUT was received on Objective The following type approved report of a radio equipment and system (RES) is prepared on behalf of the ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED in accordance with EN V9.0.2 ( ), Global System for Mobile communications (GSM); Harmonized EN for mobile stations in the GSM 900 and DCS1800 bands. The objective of the manufacturer is to determine compliance with EN V9.0.2 ( ), Global System for Mobile communications (GSM); Harmonized EN for mobile stations in the GSM 900 and DCS 1800 bands. In order to determine compliance, the manufacturer or a contracted laboratory makes measurements and takes the necessary steps to ensure that the equipment complies with the appropriate technical standards. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product maybe which result in lowering the immunity should be checked to ensure compliance has been maintained (i.e., printed circuit board layout changes, different line filter, different power supply, harnessing and/or I/O cable changes, etc.). Related Submittal(s)/Grant(s) No Related Submittal(s). Report No.: RSZ Page 4 of 39 EN V9.0.2 Test Report

5 Test Methodology All measurements contained in this report were conducted as specified in EN V9.0.2 ( ). All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory Corporation. The radiated testing was performed at an antenna-to-eut distance of 3 meters. Test Facility The Test site used by Bay Area Compliance Laboratories Corp.(Shenzhen) to collect test data is located in the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section of the FCC Rules on December 06, The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratories Corp. (Shenzhen) is an ISO/IEC accredited laboratory, and is accredited by National Voluntary Laboratory Accredited Program (Lab Code ). The current scope of accreditations can be found at Report No.: RSZ Page 5 of 39 EN V9.0.2 Test Report

6 SYSTEM TEST CONFIGURATION Justification The EUT and test equipment were configured for testing according to EN V9.0.2 ( ). The GPRS item test was performed with the EUT operating at engineering mode. EUT Exercise Software N/A. Special Accessories N/A. Equipment Modifications No modifications were made to the EUT. Local Support Equipment List and Details Manufacturer Description Model Serial Number FCC ID R & S Universal Radio commutation tester CMU DoC External I/O Cable Cable Description Length (M) From/Port To Unshielded detachable Power Cable 1.5 adapter EUT Report No.: RSZ Page 6 of 39 EN V9.0.2 Test Report

7 Configuration of Test Setup Horn Antenna CMU200 EUT Block Diagram of Test Setup Horn Antenna CMU 200 AC Power Source EUT 1.0 Meter Non-Conducting Table 150 cm above Ground Plane 1.5 Meter Report No.: RSZ Page 7 of 39 EN V9.0.2 Test Report

8 SUMMARY OF TEST REPORT EN V9.0.2 ( ) Description of Test Result Section Transmitter Frequency error and phase error Compliance* Section Transmitter Frequency error under multi path and interference conditions Compliance* Section Transmitter Frequency error and Phase Error in HSCSD Multi slot Configuration N/A Section Frequency error and phase error in GPRS multi slot configuration Compliance* Section Transmitter output power and burst timing Compliance* Section Transmitter Output RF spectrum Compliance* Section Section Section Transmitter output power and burst timing in HSCSD multi slot configuration Transmitter Output RF spectrum in HSCSD multi slot configuration Transmitter Output RF spectrum for MS supporting the R-GSM frequency band Section Transmitter output power in GPRS multi slot configuration Compliance* Section Output RF spectrum in GPRS multi slot configuration Compliance* Section Conducted spurious emissions MS allocated a channel Compliance* Section Conducted spurious emission MS in idle mode Compliance* Section Conducted spurious emissions for MS supporting the R-GSM frequency band MS allocated a channel N/A Section Conducted spurious emissions for MS supporting the R-GSM frequency band MS in idle mode N/A Section Radiated spurious emissions MS allocated a channel Compliance Section Radiated spurious emissions MS in idle mode Compliance Section Radiated spurious emissions for MS supporting the R-GSM frequency band MS allocated a channel N/A Section Radiated spurious emissions for MS supporting the R-GSM frequency band MS in idle mode N/A Section Receiver blocking and spurious responses speech channels Compliance* Section Receiver blocking and spurious response speech channels for MS supporting the R-GSM frequency band N/A Section Frequency error and modulation accuracy in EGPRS configuration N/A Section Frequency error under multi path and interference conditions in EGPRS configuration N/A Section EGPRS Transmitter output power N/A Section Output RF spectrum in EGPRS configuration N/A Section Blocking and spurious response in EGPRS configuration N/A Compliance*: Please refer to the report number. RFI\MCGA1\RP76921JD02A for Telit Communications S.p.A. issued on 10 May 2010 by RFI Global Services Ltd. N/A N/A N/A Report No.: RSZ Page 8 of 39 EN V9.0.2 Test Report

9 RADIATED SPURIOUS EMISSIONS MS ALLOCATED A CHANNEL Applicable Standard Requirements: According to EN V9.0.2 ( ), section , the radiated spurious power emitted by the MS, when allocated channel, shall be no more than the levels in table 5 under normal and extreme voltage conditions. Table 5 Test Procedure a) Initially the test antenna is closely coupled to the MS and any spurious emission radiated by the MS is detected by the test antenna and receiver in the range 30 MHz to 4 GHz. NOTE 1: This is a qualitative step to identify the frequency and presence of spurious emissions which are to be measured in subsequent steps. b) The test antenna separation is set to the appropriate measurement distance and at each frequency at which an emission has been detected, the MS shall be rotated to obtain maximum response and the effective radiated power of the emission determined by a substitution measurement. In case of an anechoic shielded chamber pre-calibration may be used instead of a substitution measurement. c) The measurement bandwidth, based on a 5 pole synchronously tuned filter, is set according to table 6. The power indication is the peak power detected by the measuring system. The measurement on any frequency shall be performed for at least one TDMA frame period, with the exception of the idle frame. NOTE 2: This ensures that both the active times (MS transmitting) and the quiet times are measured. NOTE 3: For these filter bandwidths some difficulties may be experienced with noise floor above required measurement limit. This will depend on the gain of the test antenna, and adjustment of the measuring system bandwidth is permissible. Alternatively, for test frequencies above 900 MHz, the test antenna separation from the MS may be reduced to 1 meter. d) The measurements are repeated with the test antenna in the orthogonal polarization plane. e) The test is repeated under extreme voltage test conditions (see [annex 1, TC2.2]). Report No.: RSZ Page 9 of 39 EN V9.0.2 Test Report

10 Table 6 Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Rohde & Schwarz Spectrum Analyzer FSEM / HP Amplifier HP8447D 2944A HP Amplifier HP8447E 1937A HP Synthesized Sweeper 8341B 2624A Hewlett-Packard Signal Generator 8657A 3217A A.H. System Horn Antenna SAS-200/ SUNOL SCIENCES Horn Antenna DRH-118 A Rohde & Schwarz Communication, Radio Universal CMU COM POWER Dipole Antenna AD Sunol Sciences Broadband Antenna JB1 A Wellstar DC Power Supply PS N/A N/A * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed per the NVLAP requirements, traceable to the NIST. Report No.: RSZ Page 10 of 39 EN V9.0.2 Test Report

11 Environmental Conditions Temperature: 18 C ~ 22 C Relative Humidity: 45 % ~ 66 % ATM Pressure: kpa ~ kpa * Testing was performed by Jimmy Xiao on Test Results EGSM 900 Band Run # 1-1: Scan 30MHz -4GHz, Middle Channel, and Normal Voltage Condition & High Voltage Condition Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Freq. Reading Degree (m) (H/V) (dbµv) Freq. Antenna Gain Correction (dbd) Cable Loss Absolute Limit Margin V H Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Freq. Reading Degree (m) (H/V) (dbµv) Freq. Antenna Gain Correction (dbi) Cable Loss Absolute Limit Margin V V H H Report No.: RSZ Page 11 of 39 EN V9.0.2 Test Report

12 Run # 1-2: Scan 30MHz -4GHz, Middle Channel, and Low voltage Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Freq. Reading Degree (m) (H/V) (dbµv) Freq. Antenna Gain Correction (dbd) Cable Loss Absolute Limit Margin V H Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Freq. Reading Degree (m) (H/V) (dbµv) Freq. Antenna Gain Correction (dbi) Cable Loss Absolute Limit Margin V V H H Report No.: RSZ Page 12 of 39 EN V9.0.2 Test Report

13 DCS1800 Band Run # 1-1: Scan 30MHz -4GHz, Middle Channel, and Normal Voltage Condition & High Voltage Condition Below 1 GHz Indicated Test Antenna Substituted Table Angle Degree Freq. S.A. Reading (dbµv) Height (m) Polar (H/V) Freq. Antenna Gain Correction (dbd) Cable Loss Absolute Limit Margin V H Above 1 GHz Indicated Test Antenna Substituted Table Angle Degree Freq. S.A. Reading (dbµv) Height (m) Polar (H/V) Freq. Antenna Gain Correction (dbi) Cable Loss Absolute Limit Margin V H V H Report No.: RSZ Page 13 of 39 EN V9.0.2 Test Report

14 Run # 2-2: Scan 30MHz -4GHz, Middle Channel, and Low Voltage Below 1 GHz Indicated Test Antenna Substituted Table Angle Degree Freq. S.A. Reading (dbµv) Height (m) Polar (H/V) Freq. Antenna Gain Correction (dbd) Cable Loss Absolute Limit Margin V H Above 1 GHz Indicated Test Antenna Substituted Table Angle Degree Freq. S.A. Reading (dbµv) Height (m) Polar (H/V) Freq. Antenna Gain Correction (dbi) Cable Loss Absolute Limit Margin V H V H Report No.: RSZ Page 14 of 39 EN V9.0.2 Test Report

15 RADIATED SPURIOUS EMISSIONS MS IN IDLE MODE Applicable Standard Requirements: According to EN V9.0.2 ( ), section , the radiated spurious power emitted by the MS, when in idle mode, shall be no more than the levels in table 7 under normal and extreme voltage conditions. Table 7 Test Procedure a) Initially the test antenna is closely coupled to the MS and any spurious emission radiated by the MS is detected by the test antenna and receiver in the range 30 MHz to 4 GHz. NOTE 1: This is a qualitative step to identify the frequency and presence of spurious emissions which are to be measured in subsequent steps. b) The test antenna separation is set to the appropriate measurement distance and at each frequency at which a spurious emission has been detected the MS is rotated to obtain a maximum response. The effective radiated power of the emission is determined by a substitution measurement. In case of an anechoic shielded chamber pre-calibration may be used instead of a substitution measurement. c) The measurement bandwidth based on a 5 pole synchronously tuned filter shall be according to table 8. The power indication is the peak power detected by the measuring system. The measurement time on any frequency shall be such that it includes the time during which the MS receives a TDMA frame containing the paging channel. NOTE 2: For these filter bandwidths some difficulties may be experienced with noise floor above required measurement limit. This will depend on the gain of the test antenna, and adjustment of the measuring system bandwidth is permissible. Alternatively, for test frequencies above 900 MHz, the test antenna separation from the MS may be reduced to 1 meter. Table 8 d) The measurements are repeated with the test antenna in the orthogonal polarization plane. e) The test is repeated under extreme voltage test conditions (see [Annex 1, TC2.2]). Report No.: RSZ Page 15 of 39 EN V9.0.2 Test Report

16 Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Rohde & Schwarz Spectrum Analyzer FSEM / HP Amplifier HP8447D 2944A HP Amplifier HP8447E 1937A HP Synthesized Sweeper 8341B 2624A Hewlett-Packard Signal Generator 8657A 3217A A.H. System Horn Antenna SAS-200/ SUNOL SCIENCES Horn Antenna DRH-118 A Rohde & Schwarz Communication, Radio Universal CMU COM POWER Dipole Antenna AD Sunol Sciences Broadband Antenna JB1 A Wellstar DC Power Supply PS N/A N/A * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed per the NVLAP requirements, traceable to the NIST. Environmental Conditions Temperature: 18 C ~ 22 C Relative Humidity: 45 % ~ 66 % ATM Pressure: kpa ~ kpa * Testing was performed by Jimmy Xiao on Report No.: RSZ Page 16 of 39 EN V9.0.2 Test Report

17 Frequency Test Results GSM900 Band Run # 1-1: Scan 30MHz -4GHz, Idle Mode and Normal Voltage Condition & High Voltage Condition Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbd) Cable Loss Absolute ( dbm) Limit Margin H V Frequency Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbi) Cable Loss Absolute ( dbm) Limit Margin H V Frequency Run # 1-2: Scan 30MHz -4GHz, Idle Mode and Low Voltage Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbd) Cable Loss Absolute ( dbm) Limit Margin H V Frequency Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbi) Cable Loss Absolute ( dbm) Limit Margin H V Report No.: RSZ Page 17 of 39 EN V9.0.2 Test Report

18 Frequency DCS1800 Band Run # 2-1: Scan 30MHz -4GHz, Idle Mode and Normal Voltage Condition & High Voltage Condition Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbd) Cable Loss Absolute ( dbm) Limit Margin V H Frequency Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbi) Cable Loss Absolute ( dbm) Limit Margin V H Frequency Run # 2-2: Scan 30MHz -4GHz, Idle Mode and Low Voltage Below 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbd) Cable Loss Absolute ( dbm) Limit Margin V H Frequency Above 1 GHz Indicated Test Antenna Substituted Table S.A. Angle Height Polar Frequency Reading Degree (m) (H/V) (dbµv) Antenna Gain Correction (dbi) Cable Loss Absolute ( dbm) Limit Margin V H Report No.: RSZ Page 18 of 39 EN V9.0.2 Test Report

19 EXHIBIT A - CE PRODUCT LABELING Proposed CE Label Format Specifications: Text is black in color and is left justified. Labels are printed in indelible ink on permanent adhesive backing and shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT Report No.: RSZ Page 19 of 39 EN V9.0.2 Test Report

20 EXHIBIT B - EUT PHOTOGRAPHS EUT Front View EUT Rear View Report No.: RSZ Page 20 of 39 EN V9.0.2 Test Report

21 EUT Top View EUT Bottom View Report No.: RSZ Page 21 of 39 EN V9.0.2 Test Report

22 EUT Left Side View EUT Right Side View Report No.: RSZ Page 22 of 39 EN V9.0.2 Test Report

23 EUT Uncover View EUT Main Board with Shield Top View Report No.: RSZ Page 23 of 39 EN V9.0.2 Test Report

24 EUT Main Board with Shield off Top View-1 EUT Main Board with Shield off Top View-2 Report No.: RSZ Page 24 of 39 EN V9.0.2 Test Report

25 EUT Main Board with Shield Bottom View EUT Main Board with Shield off Bottom View Report No.: RSZ Page 25 of 39 EN V9.0.2 Test Report

26 EUT LCD Top View EUT LCD Bottom View Report No.: RSZ Page 26 of 39 EN V9.0.2 Test Report

27 EUT GPRS Module with Shield Top View EUT GPRS Module with Shield off Top View Report No.: RSZ Page 27 of 39 EN V9.0.2 Test Report

28 EUT GPRS Module Bottom View EUT GPS module with Shield Top View Report No.: RSZ Page 28 of 39 EN V9.0.2 Test Report

29 EUT GPS module with Shield off Top View EUT GPS module Bottom View Report No.: RSZ Page 29 of 39 EN V9.0.2 Test Report

30 EUT Bluetooth Antenna View EUT GSM Antenna View Report No.: RSZ Page 30 of 39 EN V9.0.2 Test Report

31 EUT GSM Antenna Location View EUT WIFI Antenna Top View Report No.: RSZ Page 31 of 39 EN V9.0.2 Test Report

32 EUT WIFI Antenna Bottom View EUT Accessory View Report No.: RSZ Page 32 of 39 EN V9.0.2 Test Report

33 EUT Battery Top View EUT Battery Bottom View Report No.: RSZ Page 33 of 39 EN V9.0.2 Test Report

34 EUT Adapter View EUT Adapter Information View Report No.: RSZ Page 34 of 39 EN V9.0.2 Test Report

35 EUT Adapter UncoverView EUT Adapter Main board top View Report No.: RSZ Page 35 of 39 EN V9.0.2 Test Report

36 EUT Adapter Main board bottom View Report No.: RSZ Page 36 of 39 EN V9.0.2 Test Report

37 EXHIBIT C - TEST SETUP PHOTOGRAPHS Radiated Emissions - Front View (Below 1 GHz) Radiated Emissions - Rear View (Below 1 GHz) Report No.: RSZ Page 37 of 39 EN V9.0.2 Test Report

38 Radiated Emissions - Front View (Above 1 GHz) Radiated Emissions - Rear View (Above 1 GHz) Report No.: RSZ Page 38 of 39 EN V9.0.2 Test Report

39 PRODUCT SIMILARITY DECLARATION LETTER *****END OF REPORT***** Report No.: RSZ Page 39 of 39 EN V9.0.2 Test Report