EN 62479:2010 ASSESSMENT REPORT WIN CHANNEL ELECTRONICS (HK) CO., LTD

Transcription

1 EN 62479:2010 ASSESSMENT REPORT For WIN CHANNEL ELECTRONICS (HK) CO., LTD No.1, Shangxing Road, Shangjiao, Changan Town, Dongguan, Guangdong, China Tested Model: 318EU Multiple Models: 73500, 73506, FREECOMM 200 Report Type: Amended Report Product Type: PMR (Private Mobile Radio) Report Number: RSZ A3 Report Date: Simon Wang Reviewed By: Prepared By: RF Engineer Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: Fax: Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0.

2 Report No.: RSZ A3 TABLE OF CONTENTS DOCUMENT REVISION HISTORY... 3 GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 RELATED SUBMITTAL(S)/GRANT(S)... 4 TEST METHODOLOGY... 4 EUT ALL VIEW... 5 EUT FRONT VIEW... 5 EUT REAR VIEW... 6 EUT TOP VIEW... 6 EUT BOTTOM VIEW... 7 EUT LEFT VIEW... 7 EUT RIGHT VIEW... 8 EUT CHARGER BASE BOTTOM VIEW... 8 EUT ADAPTER VIEW... 9 EUT ADAPTER LABEL VIEW... 9 EUT BATTERY TOP VIEW EUT BATTERY BOTTOM VIEW BELOW IS THE REFERENCED REPORT EN 62479: 2010 Page 2 of 11

3 Report No.: RSZ A3 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Issue 0 RSZ A1 Original Report RSZ A3 Amended Report Note: This is an amended report application based on the original report, the details as below: 1. Changing the applicant to WIN CHANNEL ELECTRONICS (HK) CO., LTD 2. Changing the applicant address to No.1, Shangxing Road, Shangjiao, Changan Town, Dongguan, Guangdong, China 3. Adding a product model of FREECOMM Changing the trade name to WE, NIPCO, Stabo 5. Changing the adapter 6. Changing the battery label Based on the above differences listed, it will not affect any test items, so we only updated the related photos. The other EUT photos and all test data please refer to the original report. EN 62479: 2010 Page 3 of 11

4 Report No.: RSZ A3 GENERAL INFORMATION Product Description for Equipment under Test (EUT) The WIN CHANNEL ELECTRONICS (HK) CO., LTD s product, model number: 318EU in this report is a PMR (Private Mobile Radio), which was measured approximately: 12.3 cm (L) * 5.5 cm (W) * 3.5 cm (H), rated with input voltage: DC 3.6 V from battery or DC 6.0 V from adapter. Adapter information: Model: AS EE020 Input: AC V, 50/60Hz, 0.15 A Output: DC 6.0 V, 0.2 A Notes: This series products model: 73500, 73506, FREECOMM 200 and 318EU are identical; they have the same or similar appearance, structure, PCB, Material and function to the testing products, and only are different for model name. Model 318EU was selected for fully testing, the detailed information can be referred to the declaration which was stated and guaranteed by the applicant. * All measurement and test data in this report was gathered from production sample serial number: (Assigned by BACL, Shenzhen).The EUT supplied by the applicant was received on Objective This report is prepared on behalf of WIN CHANNEL ELECTRONICS (HK) CO., LTD in accordance with EN 62479: 2010 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz). The objective is to determine the compliance of EUT with EN 62479: Related Submittal(s)/Grant(s) No related submittal(s). Test Methodology All measurements contained in this report were conducted with EN 62479: EN 62479: 2010 Page 4 of 11

5 Report No.: RSZ A3 EUT All View EUT Front View EN 62479: 2010 Page 5 of 11

6 Report No.: RSZ A3 EUT Rear View EUT Top View EN 62479: 2010 Page 6 of 11

7 Report No.: RSZ A3 EUT Bottom View EUT Left View EN 62479: 2010 Page 7 of 11

8 Report No.: RSZ A3 EUT Right View EUT Charger Base Bottom View EN 62479: 2010 Page 8 of 11

9 Report No.: RSZ A3 EUT Adapter View EUT Adapter Label View EN 62479: 2010 Page 9 of 11

10 Report No.: RSZ A3 EUT Battery Top View EUT Battery Bottom View EN 62479: 2010 Page 10 of 11

11 Report No.: RSZ A3 BELOW IS THE REFERENCED REPORT EN 62479: 2010 Page 11 of 11

12 EN 62479:2010 ASSESSMENT REPORT For WIN CHANNEL ELECTRONICS COMPANY LTD. No. 85, Tong gu xia Road, Shangjiao Management District, Changan Town, Dongguan City, Guangdong, China Tested Model: 318EU; Multiple Mode: 73500; Report Type: Original Report Product Type: PMR (Private Mobile Radio) Test Engineer: Rocky Kang Report Number: RSZ A1 Report Date: Jimmy Xiao Reviewed By: Prepared By: RF Engineer Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: Fax: Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Shenzhen). This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0.

13 TABLE OF CONTENTS DOCUMENT REVISION HISTORY... 3 GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 RELATED SUBMITTAL(S)/GRANT(S)... 4 TEST METHODOLOGY... 4 TEST FACILITY... 4 RF EXPOSURE MEASUREMENT... 5 EN 62479: & MAXIMUM EMITTED AVERAGE POWER... 8 TEST PROCEDURE... 8 TEST EQUIPMENT LIST AND DETAILS... 8 TEST DATA... 8 EXHIBIT A - CE PRODUCT LABELING... 9 CE LABEL FORMAT... 9 PROPOSED LABEL LOCATION ON EUT... 9 EXHIBIT B - EUT PHOTOGRAPHS EUT TOP VIEW EUT BOTTOM VIEW EUT FRONT VIEW EUT REAR VIEW EUT LEFT SIDE VIEW EUT RIGHT SIDE VIEW EUT BATTERY OFF VIEW EUT COVER OFF VIEW EUT MAIN BOARD TOP VIEW EUT MAIN BOARD TOP SHIELDING OFF VIEW EUT MAIN BOARD BOTTOM VIEW EUT LCD TOP VIEW EUT LCD BOTTOM VIEW EUT ANTENNA VIEW EUT BATTERY VIEW EN 62479:2010 Page 2 of 17

14 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 0 RSZ A1 Original Report EN 62479:2010 Page 3 of 17

15 GENERAL INFORMATION Product Description for Equipment under Test (EUT) The Win Channel Electronics Company Ltd s Model: 318EU or the "EUT" as referred to in this report is a PMR (Private Mobile Radio), which measures 12.3 cm L x 5.5 cm W x 3.5 cm H, rated input voltage: DC 3.6 V battery and DC 6.0 V adapter. Adapter Information: AC-DC ADAPTER. Model: GPG WD00; PRI: 230V AC 50Hz 13 ma; SEC: 6V DC 200mA Note: The series product model 318EU; and 73506, we select 318EU to test and all of the models are electrically identical, only they are named differently, which were explained in the attached declaration letter. * All measurement and test data in this report was gathered from production sample serial number: (Assigned by BACL, Shenzhen). The EUT supplied by the applicant was received on Objective This report is prepared on behalf of WIN CHANNEL ELECTRONICS COMPANY LTD. in accordance with EN 62479:2010 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz). The objective is to determine the compliance of EUT with EN 62479:2010. Related Submittal(s)/Grant(s) No related submittal(s). Test Methodology All measurements contained in this report were conducted with EN 62479:2010. Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section of the FCC Rules on December 06, The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. EN 62479:2010 Page 4 of 17

16 RF Exposure Measurement 1. Introduction This generic standard applies to low power electronic and electrical apparatus for which no dedicated product or product family standard regarding human exposure to electromagnetic fields applies. The frequency range covered is 10 MHz to 300 GHz. The object of this standard is to demonstrate the compliance of such apparatus with the basic restrictions on exposure of the general public to electric, magnetic and electromagnetic fields and contact current. 2. Compliance Criteria 2.1 General considerations Compliance of electromagnetic emissions from electronic and electrical equipment with the basic restrictions usually is determined by measurements and, in some cases, calculation of the exposure level. If the electrical power used by or radiated by the equipment is sufficiently low, the electromagnetic fields emitted will be incapable of producing exposures that exceed the basic restrictions. This standard provides simple EMF assessment procedures for this low power equipment. Any relevant compliance assessment procedure which is consistent with the state of the art, reproducible and gives valid results can be used. For transmitters intended for use with more than one antenna configuration option, the combination of transmitter and antenna(s) which generates the highest available antenna power and/or average total radiated power shall be assessed. Four routes, which as described as follows, can be used to demonstrate compliance with this standard: A Typical usage, installation and the physical characteristics of equipment make it inherently compliant with the applicable EMF exposure levels such as those listed in the bibliography. This low-power equipment includes unintentional (or non-intentional) radiators, for example incandescent light bulbs and audio/visual (A/V) equipment, information technology equipment (ITE) and multimedia equipment (MME) that does not contain radio transmitters. NOTE Equipment is described as A/V equipment, ITE or MME if its main use is playback/recording of music, voice or images, or processing of digital information. B The input power level to electrical or electronic components that are capable of radiating electromagnetic energy in the relevant frequency range is so low that the available antenna power and/or the average total radiated power cannot exceed the low-power exclusion level defined in 2.2. C The available antenna power and/or the average total radiated power are limited by product standards for transmitters to levels below the low-power exclusion level defined in 2.2. D Measurements or calculations show that the available antenna power and/or the average total radiated power are below the low-power exclusion level defined in 2.2. If none of these routes can be used, then the equipment is deemed to be out of the scope of this standard and EMF assessment for conformity assessment purposes shall be made according to other standards, such as IEC or other EMF product standards. EN 62479:2010 Page 5 of 17

17 2.2 Low-power exclusion level (Pmax) Low-power electronic and electrical equipment is deemed to comply with the provisions of this standard if it can be demonstrated using routes B, C or D that the available antenna power and/or the average total radiated power is less than or equal to the applicable low-power exclusion level Pmax. Annex A contains example values for Pmax derived from existing exposure limits listed in the bibliography, such as the ICNIRP guidelines [1], IEEE Std C [2], and IEEE Std C [3]. For wireless devices operated close to a person s body with available antenna powers and/or average total radiated powers higher than the Pmax values given in Annex A, the alternative Pmax values (called Pmax ), described in Annex B can also be used. For low power equipment using pulsed signals, other limits may apply in addition to those considered in Annex A and Annex B. Both ICNIRP guidelines [1] and IEEE standards [2], [3] have specific restrictions on exposures to pulsed fields, and the requirements of those standards with respect to exposure to pulses shall be met. Annex C discusses this topic further. 2.3 Exposure to multiple transmitting sources If equipment under test (EUT) is equipped with multiple intentional radiators, the overall conformity assessment might require more than just the assessment of conformity of each one of the radiators separately. The effect of multiple intentional radiators should be considered in the conformity assessment process. Technical Report IEC [8] provides generic guidance on how to assess the EMFs generated by multiple intentional radiators. 3. Limit 3.1 Annex A EN 62479:2010 Page 6 of 17

18 3.2 Annex B For wireless devices operated close to a person s body with output powers higher than the low-power exclusion levels (P max ) given in Annex A, alternative values (P max ) described in this annex B can be applied. This annex describes formulae to establish Pmax values for the 300 MHz to 6 GHz frequency range for devices that are located within 25 mm of the body. EN 62479:2010 Page 7 of 17

19 EN 62479: & MAXIMUM EMITTED AVERAGE POWER Test Procedure Refer to EN 62479: & 4.2 Test Equipment List and Details Manufacturer Description Model Serial Number Calibration Date Rohde & Schwarz EMI Test Receiver Calibration Due Date ESCI * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Data Average effective radiated power under normal test conditions Analog: Freq. (MHz) Indicated Meter Reading (dbμv) Table Angle Degree Test Antenna Height (m) Polar (H/V) Substituted Level (dbm) Ant. Gain Correction (dbd) Cable Loss (db) EN Absolute Level (dbm) V V V V V V V V Average radiated power = ( )/8 mw = mw Channel Freq. (MHz) Maximum Time Average Output (mw) Limit (mw) Result Pass Pass (mw) Note: 1. According to EUT s specification, the compliance criterion is chapter 4.2, Annex B. 2. The distance between wireless device and user s body is 0 cm. 3. BW= P max = mW % duty cycle applies to FM Modulation. Result:No SAR need test. EN 62479:2010 Page 8 of 17

20 EXHIBIT A - CE PRODUCT LABELING CE Label Format Specifications: The marking set out above must be affixed to the apparatus or to its data plate and have a minimum height of 5 mm. The elements should be easily readable and indelible. They may be placed anywhere on the apparatus case or in its battery compartment. No tool should be needed to view the marking. Note: The label should contain the below content: 1 The name of the manufacturer or the person responsible for placing the apparatus on the market 2 Type 3 Batch and/or serial numbers Proposed Label Location on EUT EN 62479:2010 Page 9 of 17

21 EXHIBIT B - EUT PHOTOGRAPHS EUT Top View EUT Bottom View EN 62479:2010 Page 10 of 17

22 EUT Front View EUT Rear View EN 62479:2010 Page 11 of 17

23 EUT Left Side View EUT Right Side View EN 62479:2010 Page 12 of 17

24 EUT Battery off View EUT Cover off View 1 EN 62479:2010 Page 13 of 17

25 EUT Main Board Top View EUT Main Board Top Shielding off View EN 62479:2010 Page 14 of 17

26 EUT Main Board Bottom View EUT LCD Top View EN 62479:2010 Page 15 of 17

27 EUT LCD Bottom View EUT Antenna View EN 62479:2010 Page 16 of 17

28 EUT Battery View *****END OF REPORT***** EN 62479:2010 Page 17 of 17