LEXUS

Transcription

1 - Retains factory features in select Lexus, Scion and Toyota vehicles with JBL Harman-Becker Digital- Synthesis Amplifier, including JBL (Pioneer-made) amplifiers while functioning with an aftermarket radio. - Pre-programmed to retain factory Steering Wheel Controls. - iphone Recognition (VR) feature from SWC on select Kenwood, Pioneer, Alpine and JVC radios. - Variable audio gain adjustment to level match the aftermarket radio and factory amplifier. - Retains OEM 3.5mm Auxiliary Audio Input. - Supports BT-HF/A2DP/AVRCP profile on select aftermarket radio models. - Supports Pick Up/, Pick up and Toggle between 1st and 2 nd incoming call, AVRCP Track, Seek. - EIA color coded wiring for easy installation. LEXUS SCION ES300 IS300 LS430 FRS im iq tc xa xb xc TOYOTA Runner Avalon Camry Camry Solara Corolla FJ Cruiser Highlander Matrix Prius Rav4 Sequoia Sienna Tacoma Tundra Venza Yaris TY-61J Interface Module TY-A Harness (For Newer ls) TY-B Harness (For Older ls) 3.5MM to 4-pin SWC Cables OEM Camera Retention Harness 1 / 5 16 to 24 Pin Camera Adapter

2 2 / 5

3 IMPORTANT INSTALLATION NOTES: 1. In some Lexus/Toyota vehicles 2006 and older, the mute circuit is located in the same pin location as the amplifier turn-on on the OEM harness. If no audio is heard after the installation is complete, disconnect the BLUE/WHITE wire on the TY-61J T-Harness from the aftermarket radio AMP Turn-on wire. Insulate with tape to avoid short circuits. 2. Before connecting the 3.5mm SWC Cable, thoroughly wipe it clean with the alcohol cleansing pad provided. This will ensure a solid contact with the aftermarket radio SWC circuit. 3. To retain the factory AUXILIARY INPUT option in the vehicle, the aftermarket radio must have an Auxiliary Audio Input feature. Please check your aftermarket radio manual for details. SETTING THE AFTERMARKET RADIO BRAND This step is done on the TY-61J SWC Module. With the key in the off position, set the DIP switches to the corresponding radio listed below. 4-PIN SWC CABLE The TY-61J SWC Module allows for both types of connections: OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached) OPTION B is used for BOSS, DUAL, FAHRENHEIT, JENSEN, POWER ACOUSTIK, PIONEER, SONY and SOUND STREAM units. NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used. Special Note: Left-Right Balance Audio Control is supported. Front-Rear Audio Fading is not supported, use P/N SOHTL-20 if front to rear fading is required. GAIN ADJUSTMENTS Use the gain adjustment to level match the aftermarket radio audio output with the OE amplifier input. DIP SETTING db Volts OFF OFF OFF OFF OFF ON OFF ON OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF ON ON ON 0 db 1.7 db 3.5 db 5.2 db 7.2 db 9.1 db 11 db 12.9 db +7mV +9mV +10mV +15mV +18mV +22mV +27mV 3 / 5

4 STEERING WHEEL CONTROL BUTTON FUNCTIONS PIONEER Preset Up Preset Down Pick Up Call* Activate VR/Deactivate VR Continuous BT Active: = Toggle between ALPINE Pick Up Call Activate VR*/Deactivate VR* N/A BT Active: = Toggle between CLARION Preset Up Preset Down Pick Up Call Mute NOTE: BT Active: = Toggle between 4 / 5

5 JVC Pick Up Call* Activate VR M- M- BT Active: User must End 1st call in order to pick up 2nd incoming call. Deactivate VR: Say Cancel or remain silent until it times out Auto switch back to previous. KENWOOD BOSS Radio SWC Programming SWC Radio Wiring connection Pick Up Call/ Call History On/Off / Deactivate VR Activate VR Continuous SWC Key1 (Brown-wire) connect to Female 3.5 mm Jack - Brown wire SWC Key2 (White-wire) connect to Female 3.5 mm Jack - Brown/White wire SWC GND (Black-Wire) connect to Radio Negative wire (Black) Programming the Radio Press: [SETTING] > [STEER] > [RESET] > [High Z] Press the Steering Wheel Control (SWC) buttons set the values as listed below: Vol [ 4.07] Vol + [ 3.66] Seek [ 3.37] Seek + [ 2.98] [1.39] [ 0.00] The Value in the bracket [X.XX] will vary and will be used as parameter for each assigned function. Press: [Assign] > [4.07] > [Vol-], then the [4.07] will be replaced with [ Vol-] With [Assign] highlighted: Press: [3.66] > [Vol+], then the [3.66] will be replaced with [Vol+] Press: [3.37] > [Seek-], then the [3.37] will be replaced with [Seek-] Press: [2.98] > [Seek+], then the [2.98] will be replaced with [Seek+] Press: [1.39] > [], then the [1.39] will be replaced with [] Press: [0.00] > [Call], then the [0.00] will be replaced with [Call] Press: [Enter] for Save the setting and Exit 5 / 5