TL062. Low power JFET dual operational amplifiers. Features. Description + -
|
|
- Shana Harrison
- 5 years ago
- Views:
Transcription
1 Low power JFET dual operational amplifiers Features Very low power consumption : 0µA Wide common-mode (up to V + CC ) and differential voltage ranges Low input bias and offset currents Output short-circuit protection N DIP8 (Plastic package) High input impedance JFET input stage Internal frequency compensation Latch up free operation High slew rate : 3.5V/µs Description D SO-8 (Plastic micropackage) The, A and B are high-speed JFET input single operational amplifiers. Each of these JFET input operational amplifiers incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. 2 - Pin connections (top view) Output 2 - Inverting input 3 - Non-inverting input - V CC Non-inverting input Inverting input Output V CC + July 07 Rev 2 /
2 Schematic diagram Schematic diagram Figure. Schematic diagram V CC 2 Ω Inverting Input Non-inverting Input 6 Ω Output /2 5k Ω 270 Ω 3.2k Ω.2k Ω 0 Ω V CC 2/
3 Absolute maximum ratings and operating conditions 2 Absolute maximum ratings and operating conditions Table. Absolute maximum ratings Symbol Parameter Value M, AM, BM I, AI, BI C, AC, BC Unit V CC Supply voltage () ±8 V V i Input voltage (2) ±5 V V id Differential input voltage (3) ±30 V P tot Power dissipation 680 mw Output short-circuit duration () Infinite T stg Storage temperature range -65 to to to +50 C R thja Thermal resistance junction to (5) (6) ambient SO-8 DIP C/W R thjc ESD Thermal resistance junction to (5) (6) case SO-8 DIP8 HBM: human body model (7) 900 V MM: machine model (8) 50 V CDM: charged device model (9).5 kv 0 C/W. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between V + CC and V - CC. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 5 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 0pF discharged through a.5kω resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 0pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Table 2. Operating conditions Symbol Parameter M, AM, BM I, AI, BI C, AC, BC Unit V CC Supply voltage range 6 to 36 V T oper Operating free-air temperature range -55 to to +5 0 to +70 C 3/
4 Electrical characteristics 3 Electrical characteristics Table 3. Symbol V CC = ±5V, T amb = +25 C (unless otherwise specified) M I C Parameter Min Typ Max Min Typ Max Min Typ Max Unit V io Input offset voltage (R S = 50Ω) T amb = +25 C T min T amb T max DV io Temperature coefficient of input offset voltage (R S = 50Ω) Input offset current () I io T amb = +25 C 5 0 T min T amb T max Input bias current () I ib T amb = +25 C 30 0 T min T amb T max V icm Input common mode voltage range ±.5-2 V opp A vd Output voltage swing (R L = kω) T amb = +25 C T min T amb T max Large signal voltage gain R L = kω, V o = ±V, T amb = +25 C T min T amb T max ± ± mv μv/ C pa na pa na V 27 V GBP Gain bandwidth product T amb = +25 C, R L =kω, C L = 0pF MHz R i Input resistance Ω CMR SVR I CC V o /V o2 P D SR Common mode rejection ratio R S = 50Ω Supply voltage rejection ratio R S = 50Ω Supply current, no load T amb = +25 C, no load, no signal Channel separation A v = 0, T amb = 25 C Total power consumption T amb = +25 C, no load, no signal Slew rate V i =V, R L = kω, C L = 0pF, A v = 6 V/mV db db μa db mw V/μs /
5 Electrical characteristics Table 3. Symbol V CC = ±5V, T amb = +25 C (unless otherwise specified) (continued) M I C Parameter Min Typ Max Min Typ Max Min Typ Max Unit t r Rise time V i = mv, R L = kω, C L = 0pF, A v = μs K ov Overshoot factor (see Figure 5) V i = mv, R L = kω, C L = 0pF, A v = % e n Equivalent input noise voltage R S = 0Ω, f = khz nv Hz. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive.pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. Table. Symbol V CC = ±5V, T amb = +25 C (unless otherwise specified) AC, AI, AM BC, BI, BM Parameter Min. Typ. Max. Min. Typ. Max. Unit V io Input offset voltage (R S = 50Ω) T amb = +25 C T min T amb T max DV io Temperature coefficient of input offset voltage (R S = 50Ω) Input offset current () I io T amb = +25 C 5 0 T min T amb T max 3 Input bias current () I ib T amb = +25 C 30 0 T min T amb T max 7 V icm V opp A vd Input common mode voltage range Output voltage swing (R L = kω) T amb = +25 C T min T amb T max Large signal voltage gain R L = kω, V o = ±V, T amb = +25 C T min T amb T max ± mv µv/ C 27 6 ± pa na na 27 V GBP Gain bandwidth product T amb = +25 C, R L =kω, C L = 0pF MHz R i Input resistance 2 2 Ω CMR Common mode rejection ratio R S = 50Ω 6 V/mV db 5/
6 Electrical characteristics Table. Symbol V CC = ±5V, T amb = +25 C (unless otherwise specified) (continued) AC, AI, AM BC, BI, BM Parameter Min. Typ. Max. Min. Typ. Max. Unit SVR I CC V o /V o2 P D SR t r Supply voltage rejection ratio R S = 50Ω Supply current, no load T amb = +25 C, no load, no signal Channel separation A v = 0, T amb = +25 C Total power consumption T amb = +25 C, no load, no signal Slew rate V i = V, R L = kω, C L = 0pF, A v = Rise time V i = mv, R L = kω, C L = 0pF, A v = K ov Overshoot factor (see Figure 5) V i = mv, R L = kω, C L = 0pF, A v = e n Equivalent input noise voltage R S = 0Ω, f = khz db µa mw V/μs μs % 2 2 nv Hz. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive.pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. 6/
7 Electrical characteristics Figure 2. Maximum peak-to-peak output voltage versus supply voltage Figure 3. Maximum peak-to-peak output voltage versus free air temp Figure. Maximum peak-to-peak output voltage versus load resistance Figure 5. Maximum peak-to-peak output voltage versus frequency Figure 6. Differential voltage amplification versus free air temperature Figure 7. Large signal differential voltage amplification and phase shift versus frequency DIFFERENTIAL VOLTAGE AMPLIFICATION (V/mV) 7 2 V CC = 5V R L = kω FREE AIR TEMPERATURE ( C) DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) PHASE SHIFT (right scale) V CC = 5V to 5V R L = 2kΩ T amb = +25 C DIFFERENTIAL VOLTAGE AMPLIFICATION (left scale) 80 0 k k 0k M M FREQUENCY (Hz) /
8 Electrical characteristics Figure 8. Supply current per amplifier versus supply voltag Figure 9. Supply current per amplifier versus free air temperature SUPPLY CURRENT (μa) T amb = +25 C No signal No load SUPPLY VOLTAGE ( V) SUPPLY CURRENT (μa) V CC No signal No load = 5V FREE AIR TEMPERATURE ( C) Figure. Total power dissipated versus free air temperature Figure. Common mode rejection ratio versus free air temperature TOTAL POWER DISSIPATED (mw) = 5V V CC No signal No load FREE AIR TEMPERATURE ( C) COMMON MODE REJECTION RATIO (db) V CC = 5V R L = kω FREE AIR TEMPERATURE ( C) Figure 2. Normalized unity gain bandwidth slew rate, and phase shift versus temperature Figure 3. Input bias current versus free air temperature NORMALIZED UNITY-GAIN BANDWIDTH AND SLEW RATE.3.2. UNITY-GAIN-BANDWIDTH (left scale) PHASE SHIFT (right scale) SLEW RATE (left scale) V CC = 5V R L = kω f = B for phase shift FREE AIR TEMPERATURE ( C) NORMALIZED PHASE SHIFT INPUT BIAS CURRENT (na) 0 V CC = 5V FREE AIR TEMPERATURE ( C) 8/
9 Electrical characteristics Figure. Voltage follower large signal pulse response Figure 5. Output voltage versus elapsed time INPUT AND OUTPUT VOLTAGES (V) INPUT V CC = 5V R = kω L C L = 0pF T amb = +25 C OUTPUT TIME (μs) OUTPUT VOLTAGE (mv) OVERSHOOT % 90% V CC = 5V R L = kω T t amb = +25 C r TIME (μs) Figure 6. Equivalent input noise voltage versus frequency EQUIVALENT INPUT NOISE VOLTAGE (nv/vhz) VCC = 5V R S = 0Ω T amb = +25 C k k k 0k 0k FREQUENCY (Hz) Parameter measurement information Figure 7. Voltage follower Figure 8. Gain-of- inverting amplifier k Ω - /2 - e o e I k Ω - /2 e o e I C L = 0pF R = k Ω L R L C L = 0pF 9/
10 Typical applications Typical applications Figure 9. 0KHz quadrature oscillator N 8 8k Ω * -5V 8pF 8pF k Ω 88.k Ω - /2 8pF 6 sin ω t 88.k Ω - /2 k Ω 6 cos ω t 88.k Ω N 8 8k Ω * +5V. These resistor values may be adjusted for a symmetrical output. 5 Package information In order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: /
11 Package information Figure. Ref. DIP8 package mechanical data Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. A A A b b c D E E e ea eb L /
12 Package information Figure 2. Ref. SO-8 package mechanical data Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. A A A b c D H E e h L k 8 8 ccc /
13 Ordering information 6 Ordering information Table 5. Part number Order codes Temperature range Package Packing Marking MN AMN BMN MD/MDT AMD/AMDT BMD/BMDT -55 C, +25 C DIP8 SO-8 Tube Tube or tape & reel MN AMN BMN 062M 062AM 062BM IN AIN BIN ID/IDT AID/AIDT BID/BIDT -0 C, +5 C DIP8 SO-8 Tube Tube or tape & reel IN AIN BIN 062I 062AI 062BI CN ACN BCN CD/CDT ACD/ACDT BCD/BCDT 0 C, +70 C DIP8 SO-8 Tube Tube or tape & reel CN ACN BCN 062C 062AC 062BC 7 Revision history Table 6. Document revision history Date Revision Changes 28-Mar-0 Initial release. 27-Jul-07 2 Added values for R thja and R thjc in Table : Absolute maximum ratings. Added Table 2: Operating conditions. Updated format. 3/
14 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 07 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America /
LF253 LF353. Wide bandwidth dual JFET operational amplifiers. Features. Description
Wide bandwidth dual JFET operational amplifiers Features Low power consumption Wide common-mode (up to V CC + ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationTL064. Low power JFET quad operational amplifier. Features. Description
Low power JFET quad operational amplifier Features Very low power consumption: 0 µa Wide commonmode (up to V + CC ) and differential voltage ranges Low input bias and offset currents Output shortcircuit
More informationLF253, LF353. Wide bandwidth dual JFET operational amplifiers. Features. Description
Wide bandwidth dual JFET operational amplifiers Features Low power consumption Wide common-mode (up to + ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationMC33172 MC Low power dual bipolar operational amplifiers. Features. Description
Low power dual bipolar operational amplifiers Features Good consumption/speed ratio: only 200 µa for 2.1MHz, 2V/µs Single (or dual) supply operation from +4 V to +44V (±2V to ±22V) Wide input common mode
More informationTL084. General purpose JFET quad operational amplifier. Features. Description
General purpose JFET quad operational amplifier Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Output shortcircuit protection High input impedance
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
Low noise JFET quad operational amplifier Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ) Output shortcircuit protection
More informationMC Low noise quad operational amplifier. Features. Description
MC3379 Low noise quad operational amplifier Features Low voltage noise: 4.5 nv/ Hz High gain bandwidth product: 15 MHz High slew rate: 7 V/µs Low distortion:.2% Large output voltage swing: +14.3 V/-14.6
More informationTS522. Precision low noise dual operational amplifier. Features. Description
Precision low noise dual operational amplifier Datasheet production data Features Large output voltage swing: +14.3 V/-14.6 V Low input offset voltage 850 μv max. Low voltage noise: 4.5 nv/ Hz High gain
More informationTS27L4. Very low power precision CMOS quad operational amplifiers. Features. Description
Very low power precision CMOS quad operational amplifiers Features Very low power consumption: µa/op Output voltage can swing to ground Excellent phase margin on capacitive loads Unity gain stable Two
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
Low noise JFET quad operational amplifier Datasheet production data Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ)
More informationNon-inverting input 1. Part Number Temperature Range Package Packing Marking. 4558C MC4558CPT TSSOP8 Tape & Reel MC4558IN
Wide Bandwidth Dual Bipolar Operational Amplifier Internally compensated Short-circuit protection Gain and phase match between amplifier Low power consumption Pin-to-pin compatible with MC1458/LM358 Gain
More informationLM248, LM348. Four UA741 quad bipolar operational amplifiers. Description. Features
Four UA741 quad bipolar operational amplifiers Description Datasheet - production data Features D SO14 Pin connections (top view) Low supply current: 0.53 ma per amplifier Class AB output stage: no crossover
More informationObsolete Product(s) - Obsolete Product(s)
Low power quad operational amplifier Features Wide gain bandwidth: 1.3 MHz Extended temperature range: -40 C to +150 C Input common-mode voltage range includes negative rail Large voltage gain: 100 db
More informationTL062 TL062A - TL062B
TL62 TL62A TL62B LOW POWER JFET DUAL OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO + ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
More informationTL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
More informationOrder code Temperature range Package Packaging Marking
Micropower quad CMOS voltage comparator Datasheet production data Features Extremely low supply current: 9 μa typ./comp. Wide single supply range 2.7 V to 16 V or dual supplies (±1.35 V to ±8 V) Extremely
More informationTS3704. Micropower quad CMOS voltage comparators. Features. Description
Micropower quad CMOS voltage comparators Features Push-pull CMOS output (no external pull-up resistor required) Extremely low supply current: 9μa typ per comparator Wide single supply range 2.7V to 6V
More informationTL072 TL072A - TL072B
TL072 TL072A - TL072B Low noise J-FET dual operational amplifiers Features Wide common-mode (up to V + CC ) and differential voltage range Low input bias and offset current Low noise e n = 15nV/ Hz (typ)
More informationLM2903H. Low-power dual voltage comparator. Features. Description
LM23H Low-power dual voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent
More informationTL084. General purpose JFET quad operational amplifiers. Features. Description
General purpose JFET quad operational amplifiers Datasheet production data Features Wide commonmode (up to V + CC ) and differential voltage range Low input bias and offset current Output shortcircuit
More informationLM2903W. Low-power, dual-voltage comparator. Features. Description
Low-power, dual-voltage comparator Datasheet production data Features Wide, single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationLM2901. Low power quad voltage comparator. Features. Description
Low power quad voltage comparator Features Wide single supply voltage range or dual supplies for all devices: +2 V to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of supply voltage
More informationTL064 TL064A - TL064B
TL6 TL6A TL6B LOW POWER JFET QUAD OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
More informationTL082 TL082A - TL082B
TL082 TL082A - TL082B GENERAL PURPOSE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationTS391. Low-power single voltage comparator. Features. Description
Low-power single voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.2 ma) independent of supply
More informationTL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationLM723CN. High precision voltage regulator. Features. Description
High precision voltage regulator Features Input voltage up to 40 V Output voltage adjustable from 2 to 37 V Positive or negative supply operation Series, shunt, switching or floating operation Output current
More informationLMV321-LMV358-LMV324. Low cost low power input/output rail-to-rail operational amplifiers. Features. Applications. Description LMV321ILT (SOT23-5)
Low cost low power input/output rail-to-rail operational amplifiers Features Operating range from V CC = 2.7V to 6V Rail-to-rail input and output Extended V icm (V DD -.2V to V CC +.2V) Low supply current
More informationLM139, LM239, LM339. Low-power quad voltage comparators. Features. Description
, LM239, LM339 Low-power quad voltage comparators Features Wide single supply voltage range or dual supplies for all devices: +2 to +36 V or ±1 V to ±18 V Very low supply current (1.1 ma) independent of
More informationTL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
More informationTSL channel buffers for TFT-LCD panels. Features. Application. Description
14 + 1 channel buffers for TFT-LCD panels Datasheet production data Features Wide supply voltage: 5.5 V to 16.8 V Low operating current: 6 ma typical at 25 C Gain bandwidth product: 1 MHz High current
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. -LM258-LM358 A-LM258A-LM358A Low power dual operational amplifiers Features
More informationTS982. Wide bandwidth dual bipolar operational amplifier. Features. Applications. Description
Wide bandwidth dual bipolar operational amplifier Features Operating from V CC = 2.5 V to 5.5 V 0 ma output current on each amplifier High dissipation package Rail-to-rail input and output Unity gain stable
More informationFeatures. Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking
Micropower quad CMOS voltage comparator Features Datasheet - production data D SO14 (plastic micropackage) P TSSOP14 (thin shrink small outline package) Pin connections top view Extremely low supply current:
More informationTS27M2, TS27M2A, TS27M2B
Low-power CMOS dual operational amplifiers Features Wide supply voltage range: 3 to 6 V Ultra-low consumption: 50 µa/op typ Output voltage swing to ground Excellent phase margin on capacitive load Gain
More informationTL082 TL082A - TL082B
TL082 TL082A - TL082B General purpose J-FET dual operational amplifiers Features Wide common-mode (up to V + CC ) and differential voltage range Low input bias and offset current Output short-circuit protection
More informationTS V micropower shunt voltage reference. Features. Applications. Description
2. micropower shunt voltage reference Features 2.5 typical output voltage Ultra low current consumption: 4µA typ. High precision @ 25 C ±2% (standard version) ±1% (A grade) High stability when used with
More informationTL072, TL072A, TL072B
Low noise JFET dual operational amplifiers Datasheet production data Features Wide common-mode (up to V CC + ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz
More informationLM2902. Low power quad operational amplifier. Features. Description
Low power quad operational amplifier Features Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes negative rail Large voltage gain: 100dB Very low supply current per amp: 375µA Low input
More informationTL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC
I, AI, BI, C, AC, BC General purpose JFET quad operational amplifiers Datasheet production data Features Wide commonmode (up to V CC + ) and differential voltage range Low input bias and offset current
More informationLM193, LM193A, LM293, LM293A, LM393, LM393A
, A, LM293, LM293A, LM393, LM393A Low Power Dual oltage Comparators Wide single-supply voltage range or dual supplies: +2 to +36 or ± to ±8 ery low supply current (.4mA) independent of supply voltage (mw/comparator
More informationLM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
More informationLow noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
More informationTL081 TL081A - TL081B
TL8 TL8A - TL8B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION HIGH
More informationTL071 TL071A - TL071B
TL7 TL7A TL7B LOW NOISE JFET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 5nV/ Hz (typ) OUTPUT SHORTCIRCUIT
More information2STC4468. High power NPN epitaxial planar bipolar transistor. Features. Application. Description
High power NPN epitaxial planar bipolar transistor Features High breakdown voltage V CEO = 140 V Complementary to 2STA1695 Typical f t = 20 MHz Fully characterized at 125 o C Application Audio power amplifier
More informationTSC1021. High-side current sense amplifier. Features. Description. Applications
High-side current sense amplifier Features Wide common-mode operating range independent of supply: 2.8 to 30 V Wide common-mode surviving range: -32 to 60 V (reversed battery and load-dump conditions)
More informationTL072 TL072A - TL072B
A - B LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORT-CIRCUIT PROTECTION
More information2STN2540. Low voltage fast-switching PNP power bipolar transistor. Features. Applications. Description
2STN2540 Low voltage fast-switching PNP power bipolar transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface mounting device in
More informationObsolete Product(s) - Obsolete Product(s)
High gain Low Voltage PNP power transistor Features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current Applications Power management in portable
More informationLM224A, LM324A. Low-power quad operational amplifiers. Features. Description
Low-power quad operational amplifiers Features Datasheet - production data D SO14 (plastic micropackage) Wide gain bandwidth: 1.3 MHz Input common mode voltage range includes ground Large voltage gain:
More informationSTD1802T4-A. Low voltage fast-switching NPN power transistor. Features. Description. Applications
Low voltage fast-switching NPN power transistor Features This device is qualified for automotive application Very low collector to emitter saturation voltage High current gain characteristic Fast-switching
More informationL4940xx5 L4940V5 L4940D2T5-TR 5 V L4940xx85 L4940V85 L4940P85 L4940D2T85-TR 8.5 V L4940xx10 L4940D2T10-TR 10 V L4940xx12 L4940D2T12-TR 12 V
Very low drop 1.5 A regulator Features Precise 5, 8.5, 10, 12 V outputs Low dropout voltage (450 mv typ. at 1 A) Very low quiescent current Thermal shutdown Short circuit protection Reverse polarity protection
More informationLM193, LM293, LM393. Low power dual voltage comparators. Features. Description
, LM293, LM393 Low power dual voltage comparators Features Wide single-supply voltage range or dual supplies: +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply voltage
More informationBD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
More informationTL084 TL084A - TL084B
A B GENERAL PURPOSE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORTCIRCUIT PROTECTION HIGH INPUT IMPEDANCE
More informationPart Number Temperature Range Package Packing Marking. DIP14 Tube LM2902N LM2902D/DT SO-14 Tube or Tape & Reel
Low Power Quad Operational Amplifier Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes ground Large voltage gain: 1dB Very low supply current per amp: 375µA Low input bias current: 2nA
More information2STA1943. High power PNP epitaxial planar bipolar transistor. Features. Application. Description
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO > -230V Complementary to 2STC5200 Fast-switching speed Typical f T = 30 MHz Application Audio power amplifier Description
More informationLM323. Three-terminal 3 A adjustable voltage regulators. Features. Description
Three-terminal 3 A adjustable voltage regulators Features Output current: 3 A Internal current and thermal limiting Typical output impedance: 0.01 W Minimum input voltage: 7.5 V Power dissipation: 30 W
More informationObsolete Product(s) - Obsolete Product(s)
High Gain Low Voltage PNP Power Transistor General features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current In compliance with the 2002/93/EC
More information2STX2220. High Gain Low Voltage PNP Power Transistor. General features. Description. Internal schematic diagram. Applications.
High Gain Low Voltage PNP Power Transistor General features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current In compliance with the 2002/93/EC
More informationTS27M4C, TS27M4I, TS27M4M
Precision low power CMOS quad operational amplifiers Features Low power consumption: 50 µa/op Output voltage can swing to ground Excellent phase margin on capacitive loads Unity gain stable Two input offset
More informationObsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s)
5 A low dropout fast response positive voltage regulator adjustable Features Typical dropout 1.2 V Fast transient response Three terminal adjustable Guaranteed output current up to 5 A Output tolerance
More informationOrder codes Marking Package Packaging 2STF SOT-89 2STN2550 N2550 SOT-223. November 2008 Rev 1 1/8
2STF2550 2STN2550 Low voltage high performance PNP power transistors Preliminary Data Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface
More informationMJE182 Low voltage high speed switching NPN transistor Features Applications Description High speed switching NPN device
Low voltage high speed switching NPN transistor Features High speed switching NPN device Applications Audio amplifier High speed switching applications Description This device is an NPN low voltage transistor
More information2STC5242. High power NPN epitaxial planar bipolar transistor. Features. Application. Description
2STC5242 High power NPN epitaxial planar bipolar transistor Features High breakdown voltage V CEO = 230 V Complementary to 2STA1962 Fast-switching speed Typical f T = 30 MHz Application Audio power amplifier
More informationD44H8 - D44H11 D45H8 - D45H11
D44H8 - D44H11 D45H8 - D45H11 Complementary power transistors Features. Low collector-emitter saturation voltage Fast switching speed TAB Applications Power amplifier Switching circuits 1 2 3 Description
More informationObsolete Product(s) - Obsolete Product(s)
PNP power Darlington transistor Features Monolithic Darlington configuration Integrated antiparallel collector-emitter diode Application Linear and switching industrial equipment Description The TIP145
More informationObsolete Product(s) - Obsolete Product(s)
2 W mono amplifier Features 2 W output power into 8 Ω at 12 V, THD = 10% Internally fixed gain of 32 db No feedback capacitor No boucherot cell Thermal protection AC short-circuit protection SVR capacitor
More informationOrder codes Marking Package Packaging. STD2805T4 D2805 DPAK Tape & reel STD D2805 IPAK Tube. June 2007 Rev 1 1/9
Low voltage fast-switching PNP power transistor Preliminary Data Features Very low collector to emitter saturation voltage High current gain characteristic Fast-switching speed Surface-mounting DPAK (TO-252)
More informationTSH110-TSH111-TSH112-TSH113-TSH114
Wide band low noise operational amplifiers Features Low noise: 3nV/ Hz Low supply current: 3.2mA 47mA output current Bandwidth: 100MHz 5V to 12V supply voltage Slew rate: 450V/μs Specified for 100Ω load
More informationObsolete Product(s) - Obsolete Product(s)
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO = -250 V Complementary to 2STC5949 Typical f t = 25 MHz Fully characterized at 125 o C Application Audio power amplifier
More information2STD1665. Low voltage fast-switching NPN power transistor. Features. Applications. Description
Low voltage fast-switching NPN power transistor Features Very low collector to emitter saturation volatage High current gain characteristic Fast-switching speed Through-hole IPAK (TO-251) power package
More informationBUL39D. High voltage fast-switching NPN power transistor. Features. Application. Description
High voltage fast-switching NPN power transistor Features Integrated antiparallel collector-emitter diode High voltage capability Low spread of dynamic parameters Minimum lot-to-lot spread for reliable
More information2N2219AHR. Hi-Rel NPN bipolar transistor 40 V A. Features. Description
Hi-Rel NPN bipolar transistor 40 V - 0.8 A Features BV CEO 40 V I C (max) 0.8 A H FE at 10 V - 150 ma > 100 Operating temperature range - 65 C to + 200 C Hi-Rel NPN bipolar transistor Linear gain characteristics
More informationSTB High voltage fast-switching NPN power transistor. Features. Applications. Description
High voltage fast-switching NPN power transistor Features Low spread of dynamic parameters Minimum lot-to-lot spread for reliable operation Very high switching speed Through hole TO-262 (I 2 PAK) power
More informationRT2904WH. RobuST low-power dual operational amplifier. Applications. Features. Description
RobuST low-power dual operational amplifier Datasheet - production data Features D SO8 (plastic micropackage) Pin connections (top view) Frequency compensation implemented internally Large DC voltage gain:
More informationLMV321, LMV358, LMV324
Low cost, low power, input/output rail-to-rail operational amplifiers Features Operating range from V CC = 2.7 V to 6 V Rail-to-rail input and output Extended V icm (V DD -.2 V to V CC +.2 V) Low supply
More informationBD533 BD535 BD537 BD534 BD536
BD533 BD535 BD537 BD534 BD536 Complementary power transistors Features. BD533, BD535, and BD537 are NPN transistors Description The devices are manufactured in Planar technology with Base Island layout.
More informationLD1085CXX. 3 A low-drop, adjustable positive voltage regulator. Features. Description
3 A low-drop, adjustable positive voltage regulator Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable output voltage Guaranteed output current up to 3 A Output tolerance ± 2 % at 25 C and
More information2STR SOT-23 Tape and reel 2STR1230G 130G SOT-23 Tape and reel
Low voltage fast-switching NPN power transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Miniature SOT-23 plastic package for surface
More informationTSH103. Low cost triple video buffer/filter for standard video. Features. Applications. Description
Low cost triple video buffer/filter for standard video Features Triple channels Internal 6 MHz reconstruction filter (4 th order) 6 db gain buffer for lines 5 V single supply Bottom of video signal close
More informationObsolete Product(s) - Obsolete Product(s)
Three-terminal 5 A adjustable voltage regulators Features Guaranteed 7 A peak output current Guaranteed 5 A output current Adjustable output down to 1.2 V Line regulation typically 0.005 %/V Load regulation
More informationLM158-LM258-LM358. Low power dual operational amplifiers. Features. Description
-LM258-LM358 Low power dual operational amplifiers Features Internally frequency compensated Large DC voltage gain: 100 db Wide bandwidth (unity gain): 1.1 MHz (temperature compensated) Very low supply
More informationSTD840DN40. Dual NPN high voltage transistors in a single package. Features. Applications. Description
Dual NPN high voltage transistors in a single package Datasheet production data Features Low V CE(sat) Simplified circuit design Reduced component count Fast switching speed Applications Compact fluorescent
More informationTS881. Rail-to-rail 0.9 V nanopower comparator. Description. Features. Applications
Rail-to-rail 0.9 V nanopower comparator Description Datasheet - production data SC70-5 (top view) SOT23-5 (top view) The TS881 device is a single comparator featuring ultra low supply current (210 na typical
More informationTL1431. Programmable voltage reference. Features. Description
Programmable voltage reference Features Adjustable output voltage: V REF to 36 V Sink current capability: 1 to 100 ma Typical output impedance: 0.22 Ω 0.4% and 0.25% voltage precision Description The TL1431
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
TL074 Low noise JFET quad operational amplifier Features Wide commonmode (up to V CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ) Output shortcircuit
More informationESDALCL6-4P6A. Multi-line low capacitance and low leakage current ESD protection. Features. Applications. Description
Multi-line low capacitance and low leakage current ESD protection Features Datasheet production data Diode array topology: 4 lines protection Low leakage current: 10 na at 3 V 1 na at 1 V Very low diode
More informationNE555 SA555 - SE555 General-purpose single bipolar timers Features Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
More information2STA1695. High power PNP epitaxial planar bipolar transistor. Features. Applications. Description
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO = -140 V Complementary to 2STC4468 Typical f t = 20 MHz Fully characterized at 125 C Applications 1 2 3 Audio power
More informationLow noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
More information3STL2540. Low voltage high performance PNP power transistor. Features. Applications. Description
Low voltage high performance PNP power transistor Datasheet production data Features Very low collector-emitter saturation voltage High current gain characteristic Small, thin, leadless SMD plastic package
More informationBDX53B - BDX53C BDX54B - BDX54C
BDX53B - BDX53C BDX54B - BDX54C Complementary power Darlington transistors Features Good h FE linearity High f T frequency Monolithic Darlington configuration with integrated antiparallel collector-emitter
More informationHCF4093. QUAD 2-input NAND Schmidt trigger. Features. Description
QUAD 2-input NAND Schmidt trigger Features Schmidt trigger action on each input with no external components Hysteresis voltage typically 0.9 V at V DD =5V and 2.3 V at V DD =10 V Noise immunity greater
More informationKF25B, KF33B KF50B, KF80B
KF25B, KF33B KF50B, KF80B Very low drop voltage regulators with inhibit Datasheet production data Features Very low dropout voltage (0.4 V) Very low quiescent current (typ. 50 µa in OFF mode, 500 µa in
More informationL78S00 series. 2A Positive voltage regulators. Feature summary. Description. Schematic diagram
2A Positive voltage regulators Feature summary Output current to 2A Output voltages of 5; 7.5; 9; 10; 12; 15; 18; 24V Thermal overload protection Short circuit protection Output transition SOA protection
More informationST26025A. PNP power Darlington transistor. Features. Applications. Description
ST26025A PNP power Darlington transistor Features High current monolithic Darlington configuration Integrated antiparallel collector-emitter diode Applications Automotive fan control Linear and switching
More information