RF RANGE REFERENCE GUIDE. 2.4 GHz

Transcription

1 RF RANGE REFERENCE GUIDE 2.4 GHz 1. Maximum RF Range Data Chart 2. Cable Attenuation/Signal Loss 3. Non-Directional vs Directional Antenna 4. RSSI & Other Helpful Information 5. Antenna Specifications 23 Hubble Irvine, CA Phone: (Toll-free) / Fax: Sales@OleumTech.com OleumTech Corporation. All rights reserved. WIO and BreeZ are registered trademarks of OleumTech Corporation in the United States. Other trademarks are the property of their respective owners. Specifications, design, and product descriptions subject to change without notice. Document ID: AN a

2 MAXIMUM RF RANGE GUIDE TRANSMITTER to GATEWAY ,000 bit RATE Transmit Receive BULKHEAD ANTENNA, 3 db TRANSMITTER TX POWER GATEWAY TX POWER RF RANGE* 10dBm 10dBm 1000 ft / 305 m 18dBm 18dBm 1250 ft / 381 m Transmit Receive OMNI ANTENNA 24-IN, 8 dbi TRANSMITTER TX POWER GATEWAY TX POWER RF RANGE* 10dBm 10dBm 2800 ft / 853 m 18dBm 18dBm 5500 ft / 1.7 Km Transmit Receive YAGI ANTENNA, 16 dbi TRANSMITTER TX POWER GATEWAY TX POWER RF RANGE* 10dBm 10dBm 7500 ft / 2.3 Km 18dBm 18dBm 8500 ft / 2.6 Km *Field tested with clear line of sight with antennas raised to 9 to 15 ft above ground at sea level (tested for point-to-point values only). Actual wireless RF range may vary depending on location, antenna and cable setup, and line of sight. Graphs not to scale.

3 CABLE ATTENUATION 2.4 GHz ATTENUATION / COAX CABLE LOSS IN db CABLE TYPE 1 ft / 0.3 m 10 ft / 3 m 25 ft / 7.6 m 50 ft / 15.2 m 100 ft / 30.5 m 200 ft / 61 m RG db 7.5 db 18.8 db 37.5 db 75 db 150 db LMR db 0.7 db 1.7 db 3.4 db 6.8 db 13.6 db RG-174 Type N Male to MMCX Connection Available in 6, 24, 35, and 48 inch lengths. ATX-195 Type N Male to N Male Connection Available in 15 ft length. LMR-400 Type (Low-Loss) N Male to N Male Connection Available in 30, 50, 75, and 100 ft lengths.

4 NON-DIRECTIONAL vs DIRECTIONAL ANTENNA NON-DIRECTIONAL ANTENNA (OMNI /BULKHEAD) UP RADIO ENERGY RADIO ENERGY OMNI ANTENNA SHOWN AS EXAMPLE DOWN GROUND RADIALS ANGLED DOWNWARD The Omni antenna is designed to be usable from any direction (hence its name). As a result, it doesn t have the straight-line range of the Yagi, but because it distributes its radio energy in more of a donut shape, be sure to have the main part oriented straight up and down with the feed line at the bottom. Omni antennas should be used for receiving data from multiple units scattered around the field (point-to-multipoint). DIRECTIONAL ANTENNA (YAGI) DIRECTION OF RADIO ENERGY In order to have "Gain, a Yagi antenna takes its signal strength from all around and points it in one general direction. This makes the Yagi "Directional. That means that it has to be oriented one particular way so the radio signal is pointed toward the antenna of the device with which you want to communicate. Yagi antennas should be used for relaying data to another unit (point-to-point only). ANTENNA INSTALLATION Omni Antenna 1. Position the antenna in the mounting bracket. 2. Align the antenna so that the metal base is even with or above the top of the mast tubing. 3. Tighten the mounting bracket until the antenna is secure on the mast. 4. Connect the antenna cable to the antenna. Yagi Antenna 1. Assemble Yagi antenna if needed. 2. Position the antenna in the mounting bracket. 3. Align the antenna so that the metal base of the mounting bracket is even with or above the top of the mast tubing. 4. Point the antenna to its corresponding receiver.

5 RSSI & OTHER RECOMMENDATIONS RSSI To check the RSSI (Received Signal Strength Indication) from incoming WIO Devices, connect the Base Unit Configuration Cable to either WIO Base Unit or DH2 Wireless Gateway. Using BreeZ 3.0 click on the debug tab at the bottom of the window in the Output section, it should display incoming RF Packets. If RSSI value is higher than 90 it means that the incoming signal is weak and you should increase the TX Power to improve signal quality. EXCELLENT SIGNAL = RSSI GOOD SIGNAL = RSSI POOR SIGNAL = RSSI USING A SPLITTER - Connect a splitter to the WIO Base Unit or DH2 Wireless Gateway. - Connect the Omni antenna to the 30% side of the splitter and a Yagi antenna to the 70% side of the splitter. - This will allow the device to receive data from surrounding monitors with the Omni antenna and allow the long range transmission of data with the Yagi antenna. OMNI YAGI 30% SPLITTER 70% BASE UNIT or DH2 OTHER RECOMMENDATIONS - Always weather-proof the cable connection. Failure to do so will degrade the antenna signal over time. - Lightning Arrestor should be installed outside of the enclosure. - Antenna should be installed at a height of 15 ft to improve line of sight. - If using a NEMAX enclosure the hole for the antenna wire or antenna should be made at the bottom of the enclosure to prevent from water leaks. - When building a custom antenna cable it is recommend to use LMR400 Coaxial Cable with low db loss N-Type male connector and low db loss MMCX male connector.

6 Innovative Technology for a Connected World Phantom 800 MHz-5.8GHz Antennas Phantom antenna is ideal for Cell, GSM, PCE, WiFi, and Bluetooth wireless applications Laird Technologies unique patented Phantom is a tough low-profile antenna for outdoor or indoor applications. Measuring only 2.7 tall, the Phantom 800 MHz to 5.8 GHz antenna models revolutionary design features field diversity with both vertical and horizontal polarization components. This gives the antenna diversity, frequency agility, low visibility, wide bandwidth and a low angle radiation pattern that is superior to traditional gain antennas in most applications. The industry standard NMO mounting socket mates with all Laird Technolgies magnetic, trunk lid, and hole mounts. A threaded permanent stud mount model is also available for vandal resistant mounting on brackets, panels, ceilings or any other kind of housing. The Phantom patented technology is beneficial when high performance is desired and extreme ruggedness and low profile is required. Features True Field Diversity design ensures uninterrupted transmissions in urban canyons and rural drop off areas Phantom outperforms a 3dB whip in many applications U.S. Patent Nos. 5,977,931 6,292,156 and 7,209,096 Markets Cell GSM and PCS WiFi Bluetooth wireless applications Antenna Patterns Elevation Pattern (Y, Z, or H-plane) Azimuth Pattern (X,Y, or E-plane) global solutions: local support TM Americas: IAS-AmericasEastSales@lairdtech.com Europe: IAS-EUSales@lairdtech.com Asia: IAS-AsiaSales@lairdtech.com

7 Innovative Technology for a Connected World Phantom 800 MHz-5.8GHz Antennas SPECIFICATIONS MODEL AND ORDERING INFORMATION ELECTRICAL VSWR < 2.1 Nominal Gain Maximum Power Nominal Impedance Polarization Pattern Half-Power Beamwidth (Elevation x Azimuth ) Coaxial Cable Length & Type Terminations 3 db-m.e.g. 100 W 50 Ω Vertical & Horizontal Omnidirectional 130 x 360 None NMO Socket or, type N-female MODEL TRA8063 TRA8213 TRA8903 TRA9023 TRA18503 TRA24003 TRA58003 TRADCAGP Sealtube3 DESCRIPTION MHz 3 db-meg Phantom ¾ NMO, White Radome MHz 3 db-meg Phantom ¾ NMO, White Radome MHz 3 db-meg Phantom ¾ NMO, White Radome MHz 3 db-meg Phantom ¾ NMO, White Radome GHz 3dB-MEG Phantom ¾ NMO, White Radome GHz 3 db-meg Phantom ¾ NMO, White Radome GHz 3 db-meg Phantom ¾ NMO, White Radome G - Drop ceiling antenna adaptor for P-mount Phantom w/ 6 x6 x0.016 ground plane Heat shrink tubing 3 x1 DIA install (use for jaw protector on installation wrench) Mechanical Add B to model number for black radome. Example: TRAB8063 Add P to model number for Permanent Mount. Example: TRA8063P Color Black or White Height (initially) 2¾ Diameter Weight Material Mounting Information Noise Suppressor lb ABS NMO (PN: MB8, MAB8) Sold Separately BlackHawk NS VOLT, 15 Amp Noise Suppessor (Sold Separately) Permanent Mounting Option: Please order by antenna model and insert letter P to indicate permanent mounting option (TRA8063P). ANT-DS-PHANTOM MHz 0310 Any information furnished by Laird Technologies, Inc. and its agents is believed to be accurate and reliable. All specifications are subject to change without notice. Responsibility for the use and application of Laird Technologies materials rests with the end user, since Laird Technologies and its agents cannot be aware of all potential uses. Laird Technologies makes no warranties as to the fitness, merchantability or suitability of any Laird Technologies materials or products for any specific or general uses. Laird Technologies shall not be liable for incidental or consequential damages of any kind. All Laird Technologies products are sold pursuant to the Laird Technologies Terms and Conditions of sale in effect from time to time, a copy of which will be furnished upon request. Copyright 2010 Laird Technologies, Inc. All Rights Reserved. Laird, Laird Technologies, the Laird Technologies Logo, and other marks are trade marks or registered trade marks of Laird Technologies, Inc. or an affiliate company thereof. Other product or service names may be the property of third parties. Nothing herein provides a license under any Laird Technologies or any third party intellectual property rights.

8 Laird Technologies Web site: Item # FG24008, Fiberglass Omnidirectional Wireless Antennas Fiberglass Omnidirectional Wireless Antennas Includes VHF through 2.4 GHz models High performance and reliable collinear J-pole design surrounded by durable high density fiberglass Durable gold anodized sleeve and cap will not oxidize Custom tuning available FedEx/UPS shippable on most models SPECIFICATIONS Model 2.4 GHZ Models Frequency Range MHz Tuned Frequency 2450 MHz Gain 8 dbi Length 24 inches Max. Power 100 watts Options 4 Inch Wall Mount 9 Inch Standoff (2) Fiberglass Mounting Bracket (2) Stainless Steel U-Bolt Mount (2) 3/7/2012 Page 1 of 1

9 Innovative Technology for a Connected World Vagi Series Antenna VA MHz VAGI SERIES ANTENNA The Vagi Series antenna system offered by Laird Technologies is constructed of die cast aluminum alloy with anti-corrosion alodine finish. They come standard with a choice of an N female or N male connector and an adjustable 45 tilt galvanized steel QuikClamp bracket which accommodates a 1 to 1.5 inch pole diameter. The Vagi Series antenna can be used in a wide variety of wireless systems where low cost, good performance and low wind loading are important factors. Because of their low visual impact, they have been approved for use by many homeowner associations with strict CC&R restrictions. Various frequency options are available between 1700 and 2700 MHz (contact Laird Technologies for different frequency or connector options). FEATURES Compact, low profile 16 dbi antenna gain Low cost compared to other 16 dbi gain antennas Very low wind loading aesthetic design QuikClamp bracket for 1.0 to 1.5 in pole diameter 45 tilt and 360 rotation adjustments Vertical or horizontal polarization 24 in pigtail with type N female or N male connector Rugged, lightweight, and waterproof Frequency options available between 1700 and 2700 Mhz MARKETS 2.4 GHz ISM band applications Wireless broadband systems WISP CPE equipment Wireless internet access Point-to-multi-point systems Building-to-building high speed links WiMAX ANTENNA PATTERNS global solutions: local support TM Americas: IAS-AmericasEastSales@lairdtech.com Europe: IAS-EUSales@lairdtech.com Asia: IAS-AsiaSales@lairdtech.com

10 Innovative Technology for a Connected World Vagi Series Antenna VA24-16 SPECIFICATIONS PARAMETER Frequency range Input return loss (S11) MHz -14 db VSWR 1.5:1 Impedance Input power Pole diameter (OD) Operating temperature Gain 50 ohm 50 watts 1 to 1.5 in (25 to 38 mm) -45 to +70 C 16 dbi 3dB beam angle (E-plane) vertical polarity 25 3dB beam angle (H-plane) horizontal polarity 30 Front to back Rated wind velocity Weight Dimension L x W x H > 19 db 125 mph 1.5 lbs (0.56 kg) 22 x 3 x 4 in (559 x 76 x 102 mm) SYSTEM ORDERING VA24-16M 16 dbi Vagi Series 2.4 GHz Antenna with N Male Connector VA24-16F 16 dbi Vagi Series 2.4 GHz Antenna with N Female Connector NOTES All shipments F.O.B. Schaumburg, IL Laird Technologies does not supply the mounting pole. 16 dbi Vagi Shown in Vertical Polarization ANT-DS-VA Any information furnished by Laird Technologies, Inc. and its agents is believed to be accurate and reliable. All specifications are subject to change without notice. Responsibility for the use and application of Laird Technologies materials rests with the end user, since Laird Technologies and its agents cannot be aware of all potential uses. Laird Technologies makes no warranties as to the fitness, merchantability or suitability of any Laird Technologies materials or products for any specific or general uses. Laird Technologies shall not be liable for incidental or consequential damages of any kind. All Laird Technologies products are sold pursuant to the Laird Technologies Terms and Conditions of sale in effect from time to time, a copy of which will be furnished upon request. Copyright 2011 Laird Technologies, Inc. All Rights Reserved. Laird, Laird Technologies, the Laird Technologies Logo, and other marks are trade marks or registered trade marks of Laird Technologies, Inc. or an affiliate company thereof. Other product or service names may be the property of third parties. Nothing herein provides a license under any Laird Technologies or any third party intellectual property rights.