DATA SHEET Selectable AC transducer TAS-311DG
|
|
- Shauna Joleen Jennings
- 5 years ago
- Views:
Transcription
1 DATA SHEET Selectable AC transducer Measuring on AC networks Class 0.5 (IEC688) measurement Supply/measur. voltage up to 690 V Easy configuration via PC interface possible DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: Fax: info@deif.com Document no.: I SW version:
2 Contents Application Example of dual slope Connection diagram General technical specifications Specific technical specifications Available variants Available accessories Order specifications (examples) Accessories Dimensions in mm (inches) Mounting instructions Disclaimer...10 DEIF A/S Page 2 of 10
3 Contents Application is a micro-controller based AC transducer with 1 analogue output for measurement of RMS voltages, RMS current, phase angle or frequency on an AC-network. can be delivered pre-configured or it can be delivered un-configured for customer configuration through the PC interface. The PC configuration software allows free choice of voltage, current, phase angle or frequency measurement including configuration of the measuring range and output range without any mechanical settings or adjustments inside the transducer. The transducer holds no mechanical moving parts like potentiometers, and the calibration stability is excellent. can be configured as a normal linear transducer or with up to three slopes giving the possibility for a higher resolution in one or two ranges of the measurement. See figure below for an example of two slopes. Upper and lower output limitations can also be configured Example of dual slope For further examples, see data sheets for TAS-321DG/TAS-331DG. Output Current (ma) Upper limit End value Value at point 1 4 Start value Input Voltage (V) DEIF A/S Page 3 of 10
4 1.1.3 Connection diagram VOLTAGE/FREQUENCY CURRENT AUX SUPPLY + ~ ~ - OUTPUT AUX SUPPLY + ~ ~ - OUTPUT AUX SUPPLY + ~ ~ - OUTPUT X1 X X1 X X1 X2 N L IL1 24 N L IL1 24 N L IL1 24 L1 L1 L1 S1 S2 L3 DELTA L3 N STAR L3 P1 P2 PHASE ANGLE AUX SUPPLY + ~ ~ - OUTPUT AUX SUPPLY + ~ ~ - OUTPUT X1 X X1 X2 N L1 IL1 N L1 IL L1 S1 S2 L1 S1 S2 P1 P2 P1 P2 L3 WC3 I L3 N WC1 Coupling /24 WC3 I L1 L1 WC3 II L3 L1 WC3 III L3 L1 L1 With voltages above 480 V phase-phase! The secondary side of the current transformer MUST be connected to earth. Alternatively, a double insulated current transformer can be used. DEIF A/S Page 4 of 10
5 1.1.4 General technical specifications Accuracy Voltage/current: Class 0.5 ( C) according to IEC 688 Frequency: Class 0.2 of f max. ( C) according to IEC 688 Phase angle: Class 1.0 ( C) according to IEC 688 Meas. current (In) Overload, currents Load Meas. voltage (Un) Overload, voltages Load Frequency range Indication Output Standard range Limit Output load Output cable out/ Rload Ambient temperature 0.75/1.5/3.0/6.0 A Meas. range (I n ): 0 200% 20 A max., continuously 75 A max. for 10 s 240 A max. for 1 s Max. 0.5 VA 73/140/254/400 V phase to neutral Meas. range (U n ): 1 120% 127/240/440/690 phase to phase Meas. range (U n ): 1 120% 1.2 x U n max., continuously 2 x U n max. for 10 s Min. 480 kω Hz Red LED function: (The LED is located behind the front plate) Calibration error = flash frequency 5 Hz Configuration error = flash frequency 1 Hz 1 analogue output Output ( %): ma, 0 5 ma, ma, ma, V, V, V Output ( %): ma, ma, ma, ma, V, V, V Output ( %): ma, ma, ma, ma, V, V, V Output ( %): ma, ma, ma, ma, V, V, V Other ranges possible Max. ±120% of nominal output Current: Max. 10 V (max. 1 kω) Voltage: Max. 20 ma Max. length 30 m 10 V, 5 V, 1 V, 20 ma ranges according to IEC ma, 5 ma, 1 ma ranges ±0.5% C (nominal) C (operating) C (storage) DEIF A/S Page 5 of 10
6 Temperature coefficient Max. ±0.2% of full scale per 10 C Response time Current voltage: <105 ms in the range % of nominal input according to IEC 688 <300 ms in the range % of nominal input <85 ms in the range % of nominal input Frequency: <75 ms, typical value 50 ms Phase angle: <275 ms, typical value 200 ms Ripple Twice the class index (peak to peak measurement) according to IEC 688 Galvanic separation AC aux. models: Between inputs, outputs and aux. : 3750 V-50 Hz-1 min. DC aux. models: Between inputs and outputs: 3750 V-50 Hz-1 min. Between inputs and : 3750 V-50 Hz-1 min. Between and outputs: 1500 V-50 Hz-1 min V ac ±20% V dc -25/+30% (Aux. ) 3.5 VA/2 W Climate HSE, to DIN EMC According to EN /2/3/4 Protection Housing: IP40. Terminals: IP20 to IEC 529 and EN Aux. voltage Consumption Connections Materials Max. 2.5 mm² multi-stranded Max. 4.0 mm² single-stranded All plastic parts are self-extinguishing to UL94 (V1) DEIF A/S Page 6 of 10
7 1.1.5 Specific technical specifications Voltage Measuring voltage V ac Start value End value Connection Current Measuring current A Start value End value 0 67% of end value % of measuring voltage Star connection (UL1-N): 57 V 400 V ac Delta connection (UL1-): 100 V 690 V ac % of end value 100% of measuring current Frequency Measuring range 20 Hz...80 Hz Start value End value Measuring span 20 Hz...76 Hz 40 Hz...80 Hz 4 Hz < end value - start value Connection Star connection (UL1-N): 57 V 400 V ac. Meas. range (Un): % Delta connection (UL1-): 100 V 690 V ac. Meas. range (Un): % Phase angle Reference Delta phi = 180, Sine wave Un and Inom (Inom = 1 A or 5 A) Voltage influence 1.5 % between % Un Current influence 1.5 % between % Inom, 2.5 % between % Inom Measuring range Start value End value 0 60 /360 electrical degrees Measuring span 60 < difference between start and end values <360 Connection WC1: (IL1 and UL1-N) or (I and U-N) or (IL3 and UL3-N): V ac WC3 I: (IL1 and UL1-): V ac WC3 II: (IL1 and U-L3): V ac WC3 III: (IL1 and UL3-L1): V ac Meas. range (Un): % DEIF A/S Page 7 of 10
8 1.1.6 Available variants Type Variant no. Description Item no. Note, voltage 01, customised - AC voltage aux., voltage 02, customised - DC voltage aux., phase angle, phase angle, frequency, frequency 03, customised - AC voltage aux. 04, customised - DC voltage aux. 05, customised - AC voltage aux. 06, customised - DC voltage aux., current 07, customised - AC voltage aux., current 08, customised - DC voltage aux. 09, unconfigured - AC voltage aux. 10, unconfigured - DC voltage aux Available accessories Type Description Item no. Note Accessories for TAS TAS configuration kit Accessories for TAS 30 extra labels DEIF A/S Page 8 of 10
9 1.1.8 Order specifications (examples) The examples below are order specifications for pre-configured transducers. For un-configured transducers, only auxiliary voltage must be specified. Item no Type Voltage Current Frequency Phase angle Variant no Measuring range 0 kv 8 kv 12 kv A Hz cap ind Connection Delta (phase-phase) NA Star (phase-neutral) WC3 I VT ratio 10 kv/100 V NA - - Input voltage V NA 400 V ac 400 V CT ratio NA 100/1 A NA 500/5 A Input current NA 1.2 A NA 5 A Transfer curve Dual slope Single slope Single slope Triple slope Output start value 0 ma 4 ma 4 ma -10 V Threshold 1 4 ma V Mid value 12 ma - 12 ma 0 V Threshold V Output end value 20 ma 20 ma 20 ma 10 V Output lower limit Output upper limit 0 ma 0 ma 4 ma -12 V 22 ma 24 ma 21.5 ma 12 V Auxiliary voltage 100 V ac 110 V dc 400 V ac 220 V dc Accessories Please order separately: PC configuration kit containing connection cable and software for customer configuration Extra labels DEIF A/S Page 9 of 10
10 Dimensions in mm (inches) 99.7 (3.93) 85.0 (3.35) 4.5 (0.18) 75.0 (2.95) 61.0 (2.40) (4.33) Mounting instructions The transducer is designed for panel mounting, being mounted in a 35 mm DIN rail, or by means of two 4 mm screws. The design of the transducer makes mounting of it close to similar equipment possible, however make sure that there is min. 50 mm between the top and bottom of the transducer and other equipment. The DIN rail must always be placed horizontally when several transducers are mounted on the same rail Disclaimer DEIF A/S reserves the right to change any of the contents of this document without prior notice. DEIF A/S Page 10 of 10
DEIF A/S. TAS-311DG Selectable AC transducer J (UK) Installation and start up instructions
Installation and start up instructions TAS-311DG Selectable AC transducer Voltage, current, frequency or phase angle transducer Supply voltage up to 690V DEIF A/S Configuration via PC-interface possible
More informationDATA SHEET AC current single function transducer TAC-311DG/TAC-321DG
DATA SHEET AC current single function transducer TAC-311DG/TAC-321DG Compact design, 55 x 75 mm Easily accessible terminals Accuracy class 0.5 35 mm DIN rail or base mounting DEIF A/S Frisenborgvej 33
More informationDATA SHEET Reverse power relays, RMP-121D ANSI code 32
DATA SHEET Reverse power relays, RMP-121D ANSI code 32 Protection against "motoring" Single phase measurement LED indication of fault condition Timer-controlled tripping LED indication for activated relay
More informationRMV-122D, RMV-132D ANSI
DATA SHEET Voltage relays, RMV-112D, RMV-122D, RMV-132D ANSI codes 27/59, 59, 27 Under-voltage/over-voltage 3-phase measurement LED indication of fault condition Timer-controlled tripping LED indication
More informationTransducers for AC measurement. Types TAP, TAQ, TMF, TAA, TAV, TAC. Measurement of: watt, var, frequency, phase angle, voltage, current
Transducers for AC measurement Types TAP, TAQ, TMF, TAA, TAV, TAC 4921220002E Measurement of: watt, var, frequency, phase angle, voltage, current DEIF A/S Accuracy class 0.5 For mounting on DIN rail Compact
More informationDATA SHEET Differential current relays, RMC-131D ANSI code 87
DATA SHEET Differential current relays, RMC-131D ANSI code 87 Measurement of 3-phase currents Non-stabilised measurement Timer-controlled tripping Extra change-over relay contact for signalling DEIF A/S
More informationProtection relays and controllers. Types TRANSAL DC-2TF, ACV-3TF, ACI-3TF, PFC-2TF TRANSAL DC-2TB, AVC- 3TB, ACI-3TB, PFC-2TB
Protection relays and controllers Types TRANSAL DC-2TF, ACV-3TF, ACI-3TF, PFC-2TF TRANSAL DC-2TB, AVC- 3TB, ACI-3TB, PFC-2TB 4921250026C Transal TF Transal TB DEIF A/S Available for the following inputs:
More informationFunction. Adjustment. Extra functions included. Modes. Housing
Electronic Electronic potentiometer potentiometer DATA DATA SHEET SHEET Function Replaces normal motor potentiometers Adjustment Integrating time (like variable gearboxes) Output start value Output end
More informationDATA SHEET. Switchboard instruments,
DATA SHEET Switchboard instruments, types Standard DIN sizes Quadratic instruments: Q48 Q144 Edgewise instruments: 48 x 24 144 x 72 mm Slim edgewise instruments: 72 x 24 144 x 36 mm Accuracy class 1.5
More informationDATA SHEET. Voltmeters and Ammeters,
DATA SHEET Voltmeters and Ammeters, Moving Coil (type ) Q48, Q72, Q96, Q144 90 or 240 pointer Accuracy class 1.5 Exchangeable scale (type x) Document no.: 4921210012S Application: Moving-coil instruments
More informationDEIF A/S. Insulation monitor. Type SIM-Q
Insulation monitor 4921232C Monitoring of insulation resistance on ungrounded AC networks (IT network) Working voltage up to 69V AC, withstands up to V DC Measuring range 1...Mohm or 1...Mohm Alarm on
More information400,440Vac Vdc V, A, W, VA, var, Hz, V, Avg. A cos phi, sin phi and phi measurement kwh, kvarh (via Pulse Output)
MODEL EM4000ACF Multifunction Transducer for alternating voltage and current Power supply voltages: Suitable for DIN-rail mounting 85 240Vac 400,440Vac 24 65Vdc 100..330Vdc V, A, W, VA, var, Hz, V, Avg.
More informationDEIF A/S. Insulation monitor. Type SIM-Q/SIM-Q LF
/ LF Insulation monitor Monitoring of insulation resistance on ungrounded AC networks (IT network) Working voltage up to 69V AC, withstands up to V DC Measuring range...kω or 1...MΩ Working frequency down
More informationDATA SHEET. CIO multi-inputs. CAN bus-based I/O module
DATA SHEET CAN bus-based I/O module 8 multi-functional inputs Selectable as: o Digital input, 0(4) to 20 ma, 0 to 10 V, RMI, Pt100, Pt1000, Thermocouple type E, J, K, N, R, S or T Wire break detection
More informationDATA SHEET. Paralleling relays, HAS-111DG ANSI code 25
DATA SHEET Paralleling relays, ANSI code 25 Synchronisation of generator to busbar Setting of phase angle difference Setting of frequency and diff. LED indication of status LED for synchronising signal
More informationPrimary winding current transformer, type WSK
Technical documentation winding transformer, type DEIF /S Frisenborgvej 33 DK-7800 Sive Tel.: +45 9614 9614 Fax: +45 9614 9615 info@deif.com www.deif.com Document no.: 4921210115D Current transformers
More informationTheta 20A / 20V. Technical Data Sheet. Special Features
Technical Data Sheet Theta 20A / 20V Theta 20A / 20V is used to measure and convert AC Voltage or Current input into a load independent DC current or voltage output signal. Special Features Available in
More informationInstallation and start up instructions. Detection of vector shift. Detection of over- and underfrequency. Generator disconnection on mains failure
Installation and start up instructions G59 Relay Package uni-line 4189340236C (UK) Detection of df/dt (rate of change of frequency R.O.C.O.F.) Detection of vector shift Detection of over- and underfrequency
More informationUniversal measuring transducer
Universal measuring transducer EM4000 Compact housing High accuracy Full galvanic separation MODbus (RS232/RS485) 3 Analogue + 1 Pulse output Direct voltagemeasurement up to 690V 48 hour service EXW ELEQ
More informationTCM-2 Thyristor Control Module DATA SHEET
TCM-2 Thyristor Control Module TCM-2 Thyristor DATA DATA SHEET Control Module DATA SHEET Insulation monitors, Warning delay and power-up delay Indication of set point on front Measuring range up to 440
More informationRISH Ducer E13 3 channel transducer for AC current and voltage
RISH Ducer E13 3 channel transducer for C current and voltage The RISH Ducer E13 ( Fig. 1) converts 3 sine wave C current or C voltage into 3 output signals that can serve several receiving instruments
More informationData Sheet 066.8e. Transducers for Active and Reactive Power EW+B 2.2 DGW+B 2.2 VGW+B 2.2 DUW+B 2.2 VUW+B 2.2
Data Sheet 066.8e Transducers for Active and Reactive Power EW 2.2 DGW 2.2 VGW 2.2 DUW 2.2 VUW 2.2 Application The E/DG/VG/DU/VU W 2.2 power transducers convert all forms of active and reactive power polarity
More informationn True RMS measurement n Fully onsite programmable input voltage range (for CIP-V)
Tranducers for alternating current/voltage n True RMS measurement n Fully onsite programmable input voltage range (for CIP-V) and input current range (for CIP-I) n Available in single or dual output type
More informationPaladin Transducers 250 Series Class 0.5 and Class 0.2
Paladin Transducers 250 Series Class 0.5 and Class 0.2 An extensive range of transducers providing measurement, isolation and conversion of electrical parameters into industry standard DC output signals.
More informationAutomatic synchronising relay
Synchronising relays Types FAS-2N, FAS-3N, HAS-2N 4921250029D FAS-3N High accuracy (±3 el.) and fast synchronisation DEIF A/S Circuit breaker time compensation Test switch Voltage matching (type FAS-3N)
More informationSINEAX I 503 / SINEAX U 504 Transducer for AC current or AC voltage
Application The transducers SINEAX I 503/U 504 (Figs. 1 and 2) are designed to convert a sinusoidal AC current or voltage into a load independent DC signal proportional to the measured value. This output
More information27/04/2015
Modular Carril DIN 35 mm HIL Part number 84871120 Control of AC and DC currents Automatic recognition of AC/DC Measurement ranges from 2 ma to 10 A Choice between over and undercurrent True RMS measurement
More informationInstallation and start up instructions. Paralleling relay type HAS-111DG uni-line G (UK) Synchronisation of generator to busbar
Installation and start up instructions Paralleling relay type HAS-111DG uni-line 4189340146G (UK) Synchronisation of generator to busbar Setting of phase angle difference Setting of frequency and voltage
More informationRISH Ducer TV 808, 2 channels Isolating amplifier unipolar / bipolar
Fig. 1. Isolating amplifier RISH Ducer TV 808 in housing S 17 clipped onto a top - hat rail or screw hole mounting brackets pulled out. Features and Benefits Electric Isolation between input, and power
More informationSummation current transformers, type KSU/SUSK
Technical documentation Summation transformers, type KSU/SUSK DEIF /S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614 Fax: +45 9614 9615 info@deif.com www.deif.com Document no.: 4921210113E Data sheet
More informationTemperature transmitter itemp PCP DIN rail TMT 121
Technical information TI 087R/09/en 510 03671 Temperature transmitter itemp PCP DIN rail TMT 121 Universal temperature transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage
More informationInstallation and start up instructions. Synchroniser type FAS-115DG uni-line H (UK) Synchronisation of generator to busbar
Installation and start up instructions Synchroniser type FAS-115DG uni-line Synchronisation of generator to busbar With voltage matching Circuit breaker time compensation LED indication of status DEIF
More informationDEIF A/S. User s manual. Read synchroscope type RSQ-3. Precision LED synchronoscope. High immunity to harmonic distortion F (UK)
User s manual Read synchroscope type RSQ-3 4189340264F (UK) Precision LED synchronoscope High immunity to harmonic distortion DEIF A/S DEIF A/S Tel.: (+45) 9614 9614 Frisenborgvej 33, DK-7800 Skive Fa:
More informationInstallation / Monitoring Technique
Installation / Monitoring Technique VARIMETER RCM Residual Current Monitor, Type B for AC and DC Systems IP 5883 0249633 IP 5883 ND 5018/035 ND 5018/030 According to IEC/EN 62 020, VDE 0663 For AC and
More informationTransducing electrical quantities Iskra MIS d.d. Measuring Transducers. Features
Measuring Transducers Transducing electrical quantities Iskra MIS d.d. Measuring Transducers Features AC, DC POWER SYSTEM MEASUREMENT MICROPROCESSOR CONTROL HOUSING FOR DIN RAIL MOUNTING IN COMPLIANCE
More informationInstallation and start up instructions. Synchroniser type FAS-113DG uni-line F (UK) Synchronisation of generator to busbar
Installation and start up instructions Synchroniser type FAS-113DG uni-line Synchronisation of generator to busbar Circuit breaker time compensation LED indication of status LED indication for activated
More informationEMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description.
Electronic monitoring relay for voltage monitoring in three-phase networks INTERFACE Data sheet 102110_en_03 1 Description PHOENIX CONTACT - 09/2009 Features Increasingly higher demands are being placed
More informationTheta Hz. Technical Data Sheet. Special Features
Technical Data Sheet Theta Hz Theta Hz the transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent
More informationZelio Control Measurement Relays
Selection Guide Application Voltage control Current control Functions 3-phase Single-phase and d.c. Integrated current transformer - Overvoltage and between phases - Overvoltage and between phases and
More informationSINEAX TV 808, 2 channels Isolating Amplifier Unipolar/Bipolar
SINEAX TV 808, channels For electrically insulating, amplifying and converting DC signals Application The purpose of the isolating amplifi er SINEAX TV 808 (Fig. ) is to electrically insulate input and
More informationSINEAX U 553 Transducer for AC Voltage
With power supply RMS value measurement Carrying rail housing P/0 Application he transducer SINEAX U 55 (Fig. ) converts a sinusoidal or a distorted AC voltage into a load independent DC current or a load
More informationEnergy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302
Energy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302 Direct connection up to 65 A (WSx10x) Connection with current transformer (WSx30x) Industrial or meters
More informationMeasuring Transducer MT4xx series Programmable AC Current Transducer MT418
Measuring Transducer MT4xx series Programmable AC Current Transducer MT418 o RMS AC current or frequency measurements o Current auto range measurements up to 12 A o Frequency measurement range 16 400 Hz
More informationSeries P. Applications
Ratings 25 800 VA Voltage Primary 230 / 400 / 460 V range Secondary 6 / 12 V 12 / 24 V 24 / 48 V 115 / 230 V Voltage selection by means of metal connection bridges, offering the full rated power at any
More informationPOWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK ISO P11P, P13P and P13B mm SERVICE MANUAL
POWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK PP, PP and PB ISO 900 C E R T Y F I K A T 4 mm SERVICE MANUAL Contents Page. APPLICATION... 2. BASIC REQUIREMENTS.... TRANSDUCER SET... 4 4. TECHNICAL
More informationPhase control Single function phase control relay - 7.5 mm Control of -phase networks: phase sequence, total phase failure Multi-voltage from x 08 to x 480 V Controls its own supply voltage True RMS measurement
More informationPOWER TRANSDUCERS ACTIVE AND REACTIVE SERIES: T-W WATT T-V VAR
POWER TRANSDUCERS ACTIVE AND REACTIVE SERIES: T-W WATT T-V VAR The T-W or T-V power transducer converts ac current and voltage signals into a load independent dc signal proportional to active power (watts)
More informationRISH Ducer E13 Transducer For Ac Current Or Ac Voltage With Different Characteristics
RISH Ducer E13 Transducer For c Current Or c Voltage With Different Characteristics Data Sheet For Measurement of C Current or C Voltage Fig. 1. RISH Ducer E13 clipped onto a top - hat rail. Fig. 2. RISH
More informationTheta 60R. Technical Data Sheet. Special Features. Fig. 2 Theta R, 2 channel version, in housing S17 hole mounting brackets pulled out.
Technical Data Sheet Theta 60R 60 R 60 R Fig. Theta R, channel version, in housing S7 clipped on to a top - hat rail. Fig. Theta R, channel version, in housing S7 hole mounting brackets pulled out. Theta
More informationPower analyzers and Energy Meters. Multifunction indicator. Type WM12-DIN. Product Description. How to order WM12-DIN AV5 3 D X.
Power analyzers and Energy Meters Multifunction indicator Type WM12-DIN Accuracy ±0.5 F.S. (current/voltage) Multifunction indicator Display of instantaneous variables: 3x3 digit Variable system and phase
More informationEA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters
EA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters EA12 EA19 EA17 EA16 EB16 APPLICATION EA16, EB16, EA17, EA19 and EA12 moving-iron meters are intended for measuring AC voltage or
More informationEnergy Management Three-phase energy meter with output modules Type EM4-DIN
Energy Management Three-phase energy meter with output modules Type EM4-DIN Class 1 (active energy) Class 2 (reactive energy) Three-phase multi-function energy meter Back-lighted LCD display 3 1 / 2 DGT
More informationitemp HART DIN rail TMT112
Temperature transmitter itemp HART DIN rail TMT112 Universal temperature transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage transmitters, incorporating HART protocol Application
More informationCP-T range Benefits and advantages
Benefits and advantages Characteristics Rated output voltages V, V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output currents 5 A, 10 A, A, A Rated output powers
More informationType Nominal voltage (V) Code HSV V
Speed control Speed control relay - mm Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - -wire PNP or NPN, Namur, voltage 0-0V or volt-free contact type Works
More informationSINEAX TV 808, 1 channel Isolating Amplifier unipolar/bipolar
For electrically insulating, amplifying and converting DC signals 0102 II (1) G Application The purpose of the isolating amplifi er SINEAX TV 808 (Fig. 1 and 2) is to electrically insulate input and output
More informationProgrammable AC Voltage Transducer MT416
Programmable AC Voltage Transducer MT416 RMS AC voltage or frequency measurements Voltage auto measurements up to 600 V L-N Frequency measurement 16 400 Hz AC or universal wide auiliary power 24 300 Vdc,
More informationElectronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet
CDC 0 F0t07 Features Rated control supply voltage -8 V DC, -0 V AC Single-function timer with star-delta change-over One device includes 7 time ranges (0.0 s - 0 min) n/o contacts LEDs for status indication
More informationLED Driver Constant voltage
Driver LCU 60W 12/24V IP20 EXC excite series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to 50,000 h (at ta
More information* Short-circuit detection at On pushbutton. Applications. Indication. S M6801_a S11 A3 S12 S21 S23 S22 S (+)
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
More informationElectronic timer CT-SDS.22
CDC 0 F0t07 Features Rated control supply voltage 8 V DC, 0 V AC Single function timer with star delta change over One device includes 7 time ranges (0.0 s 0 min) n/o contacts LEDs for status indication
More informationPower analyzers and Energy Meters Power Analyzer Type WM14-DIN
Power analyzers and Energy Meters Power Analyzer Type WM14-DIN Optional RS422/485 serial port Alarms (visual only) V LN, An Class 2 (active energy) Class 3 (reactive energy) Accuracy ±0.5 F.S. (current/voltage)
More informationEnergy Management Energy Meter with plug-in Output Modules Type EM4-DIN
Energy Management Energy Meter with plug-in Output Modules Type EM4-DIN Degree of protection (front): IP 40 Front dimensions: 9 DIN modules RS 422/485 Serial port by means of optional module Dual pulse
More informationCP-T range Product group picture
Product group picture /1 ABB Catalog Electronic Products and Relays 1/1 2CDC 110 00 C09 Table of contents CP-T range Product group picture /1 Table of contents /2 Benefits and advantages / Ordering details
More informationEnergy Management Modular Smart Power Transducer Type SPT-90
Energy Management Modular Smart Power Transducer Type SPT-90 Class 0.5 (current/voltage) 16-bit µp-based modular smart power transducer Measurements of: W, Wavg, VA, VAr, PF, Wh, VAh, VArh, Amax (among
More informationMeasuring current transformers of the W, W series
Measuring current transformers of the W, W -8000 series W(-8000)_D00078_01_D_XXEN/09.2015 Measuring current transformers of the W, W -8000 series Product description The highly sensitive W and W -8000
More informationEnergy Management Power Analyzer with plug-in Output Modules Type W M22-DIN
Energy Management Power Analyzer with plug-in Output Modules Type W M22-DIN Front dimensions: 9 DIN modules Analogue output by means of optional module (20mA or 10VDC) RS 422/485 Serial port by means of
More informationHigh-quality digital indicator for panel mounting Model DI35-M, with multi-function input Model DI35-D, with two inputs for standard signals
Accessories High-quality digital indicator for panel mounting Model DI35-M, with multi-function input Model DI35-D, with two inputs for standard signals WIKA data sheet AC 80.03 Applications Machine building
More informationTemperature Transmitter itemp RTD DIN rail TMT 127
Technical Information TI 095R/09/en No. 51004790 Temperature Transmitter itemp RTD DIN rail TMT 127 Temperature Transmitter for Pt100 Resistance Thermometer Application Temperature transmitter with fixed
More informationInstallation- / Monitoring technique
Installation- / Monitoring technique ifferential current monitor IP 5883, Type B for AC and C systems varimeter 0249633 IP 5883 N 5018/035 N 5018/030 According to IEC/EN 62 020, VE 0663 To detect earth
More informationElectronic timer CT-MFS.21
2CDC 251 053 F0t07 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c Rotary switch for the preselection of the
More informationXUA1 AC Voltage and phase balance relay. (August 1996) Manual XUA1 (Revision New)
XUA1 AC Voltage and phase balance relay (August 1996) Manual XUA1 (Revision New) Woodward Manual XUA1 GB Woodward Governor Company reserves the right to update any portion of this publication at any time.
More informationAssembly. Front view. Parametrization interface. Power Bus
Temperature Converter Features Assembly 1-channel signal conditioner 24 V DC supply Thermocouple, RTD, potentiometer or mv input Input for PTC thermistor Current and voltage output Line fault (LFD) and
More informationDATASHEET - ETR4-70-A. Delivery program. Timing relay, 2W, 0.05s-100h, multi-function, VAC/DC, potentiometer connection
DATASHEET - ETR4-70-A Delivery program Timing relay, 2W, 0.05s-100h, multi-function, 24-240VAC/DC, potentiometer connection Part no. ETR4-70-A Catalog No. 031888 Eaton Catalog No. XTTR6A100H70B EL-Nummer
More informationCircuit Breakers. Excerpt from Master Catalogue. Circuit Breakers. Specifically For You
Circuit Breakers Excerpt from Master Catalogue Circuit Breakers Specifically For You Hydraulic-magnetic technology ensures reduced nuisance tripping with temperature variance Always holds 00% rated current
More informationEnergy Management Energy Meter Type EM110
Energy Management Energy Meter Type EM110 Single phase energy meter Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Electro-mechanical display Energy readout on display: 6+1 digit
More informationVariTrans P Compact automation solutions can be implemented thanks to the 17.5 mm modular housing and operation at temperatures up to 70 C.
ProLine Interface Technology Transducers for High Voltage / Shunt Applications Compact high voltage transducers with VariPower broad-range power supply and genuine calibrated range selection. The Task
More informationDifferential pressure sensors
1 912 1912P02 QBM64/ 1912P01 QBM63/ Differential pressure sensors for air and non-aggressive gases, with a diaphragm sensing element QBM63/ QBM64/ With choice of pressure-linear or extracting-the-root
More informationW DATA SHEET Current Transformer 40 x 10, A
W DATA SHEET Current Transformer 40 x 10, 250 600A W SCHRACK-INFO Current transformers for low-voltage network accuracy Single-phase current transformer Passing cable/ bus bar primary Primary current 250
More informationElectronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.23 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.
More informationNote The module converts unipolar and bipolar input signals
PROGRAMMABLE ANALOG SIGNAL CONVERTER THREE WAY GALVANIC ISOLATOR - 19 input scales - 7 output scales - 1 SPDT alarm contact - input/output isolation 3kV - auxiliary supply output for loop powered sensors
More informationEnergy Management. Type WM12-DIN. Product Description. How to order WM12-DIN AV5 3 D X. Type Selection. Input specifications
Energy Management Multifunction indicator Type WM12-DI Accuracy ±0.5 F.S. (current/voltage) Multifunction indicator Display of instantaneous variables: 3x3 digit Variable system and phase measurements:
More informationMeasuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC
2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from
More informationType CP-S, CP-C & CP-A Switch mode
Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting
More informationElectronic timer CT-SDD.22
CDC 099 F0t0 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied W
More informationPositive-guided relay outputs: 8 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Contact expander module for increasing the number of available contacts Approvals Unit features Positive-guided relay outputs: 8 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous
More informationPRELIMINARY DATA SHEET RI-D140. Three Phase Multifunction DIN Rail Energy Meter (MID Certified) MID
RI-D140 Three Phase Multifunction DIN Rail Energy Meter (MID Certified) Four module DIN rail mounted Energy pulse LED True RMS measurement Cost effective and accurate Modbus communication -/1A or -/5A
More informationFluke Fluke-Direct.ca. Three-Phase Power Logger. Technical Data
Fluke 1735 Three-Phase Power Logger Technical Data Electrical load studies, energy consumption testing, and general power quality logging The Fluke 1735 Three-Phase Power Logger is the ideal electrician
More informationProgrammable AC Current Transducer MT418
Programmable AC Current Transducer MT418 RMS AC current measurements Current auto range measurements up to 12 A Frequency measurement range 16 400 Hz AC or universal wide auiliary power supply range 24
More informationXP2-R Power and Reverse Power Relay
XP2-R Power and Reverse Power Relay Manual XP2-R (Revision C) Woodward Manual XP2-RE Woodward reserves the right to update any portion of this publication at any time. Information provided by Woodward
More information5 years! Modular Housings. VariTrans P Warranty
Modular Housings VariTrans P 27000 The Multimeter among the isolators. With 480 switchable calibrated ranges and broad-range power supply. The Task A wide range of measuring signals need to be galvanically
More informationAccessories. Accessories
Accessories Accessories Voltage transformer Voltage transformer Powerful and precise Input, 3-pole Output is 3-pole + N Use in IT networks without neutral line For reducing the measurement voltage for
More informationPECA 30E. Analyseur de signaux alternatifs Signal Analyser for Electrical Networks
Analyseur de signaux alternatifs Signal Analyser for Electrical Networks Tout type de réseau : monophasé, triphasé équilibré avec ou sans neutre All types of network: single phase, 3-phase balanced, unbalanced,
More informationRI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
More informationISOMETER IRDH575. Approvals
Insulation monitoring device for unearthed AC, DC and AC/DC systems (IT systems) with control and display function for EDS insulation fault location systems IRDH575_D00089_02_D_XXEN/09.2018 Insulation
More informationSAX..P. Electromotoric actuators for valves ACVATIX. with a 20 mm stroke
s 4 509 ACVATIX Electromotoric actuators for valves SAX..P with a 20 mm stroke SAX31P.. Operating voltage AC 230 V, 3-position control signal SAX61P.. Operating voltage AC/DC 24 V, control signal DC 0
More informationElectronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with true OFF-delay and 10 time ranges. All electronic timers from
More informationProtection relays and transformers
NEW ZEALAND WWW.LPINZ.CO.NZ Unit 6/22 Moselle Ave, Henderson, Auckland, New Zealand PO Box 21-872, Henderson, Auckland, New Zealand Phone:+64 9 833 5749 Email:info@LPINZ.co.nz Web: www.lpinz.co.nz Protection
More informationMicro Contactors. Micro Contactor Relays 10. Micro Contactors 11. Micro Contactors With Solder Pins 12. Coil voltages 12. Micro Reversing Contactor 13
Micro Contactor Relays 10 Micro Contactors 11 Micro Contactors With Solder Pins 12 Coil voltages 12 Micro Reversing Contactor 13 Technical Data 14 Dimensions 18 D946E 9 Micro Contactor Relays 4-pole AC
More informationIsolators A3/1. Temperature Transmitter Field Circuit Non-Ex i Series
Temperature Transmitter Series 9182 > One unit for nearly all temperature sensors indivdually configurable > Signal duplication possible > Galvanic isolation between input, output, power supply and configuration
More information