POWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK ISO P11P, P13P and P13B mm SERVICE MANUAL
|
|
- Mitchell Hodge
- 5 years ago
- Views:
Transcription
1 POWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK PP, PP and PB ISO 900 C E R T Y F I K A T 4 mm SERVICE MANUAL
2 Contents Page. APPLICATION BASIC REQUIREMENTS.... TRANSDUCER SET TECHNICAL DATA.... INSTALLATION Fixing Connection diagrams Measurement of active power in a single-phase network Measurement of active power in a -phase -wire network Measurement of reactive power in a -phase -wire network.... CODING AND ORDERING MAINTENANCE AND GUARANTEE... 2
3 . APPLICATION The PP transducer is destined for the conversion of active or reactive a.c. power into a d.c. current or d.c. voltage standard signal. The input, output and supply circuits are galvanically isolated (transformer separation) The conversion frequency range enables the correct measurement of power when currents and voltages are distorted (up to 2 th harmonic). The pulse feeder ensures the operation in a width range of values and frequency of the supply voltage. The measurement is realised through the analogue multiplier function with the pulse modulation (TDM). These transducers are destined to operate in industrial conditions and can be mounted in optional position. Transducer housings are made of a self-extinguishing plastic and are adapted to be fixed on mm DIN rail (DIN EN 022-). PP - transducer destined for active power measurement in a single-phase network. PP - transducer destined for active power measurement in a symmetrically loaded -phase -wire network. PB - transducer destined for reactive power measurement in a symmetrically loaded -phase -wire network. 2. BASIC REQUIREMENTS, OPERATIONAL SAFETY Symbols located in this service manual mean: Especially important, one must acquaint with this before connecting the transducer. The non-observance of notices! marked by these symbols can occasion the damage of the transducer. One must take note of this when the transducer is working? inconsistently to the expectations. In the security scope the transducer meets the requirements of the EN - standard.
4 Remarks concerning the operator safety:! PP, PP and PB transducers are destined to be mounted on mm DIN rails. In the range of operational safety they are in conformity with the EN -standard requirements. l The installation and transducer connection should be operated by a qualified personnel. l One must take into consideration all accessible protection requirements. l Before switching the instrument on, one must check the correctness of the network lead connection. l In case of the protection terminal connection with a separate lead one must remember to connect it before the connection of network leads. l Do not connect the instrument to the network through an auto-transformer. l Before taking the transducer housing out, one must turn the supply off. l The removal of the transducer housing during the guarantee contract period may cause its cancellation. The programmer connector is destined only for the PD programmer connection. After the transducer programming, one should put the hole plug of the programmer connector.. TRANSDUCER SET The transducer set includes: - PP or PP or PB transducer pc - service manual pc - guarantee card pc 4
5 4. TECHNICAL DATA Basic parameters: - input current A (X/ A), A (X/ A) - input voltage /Ö V, V, 2 V, 400 V, 0 V, 90 V, X/ V - output signals ma, ma, 4... ma, V - accuracy class 0. - output load resistance: - for ma current output W - for ma current output W - for V voltage output ³ 0 W - circuit consumption: - voltage measurement 0. VA - current measurement 0. VA - supply VA - preheating time of the transducer min. - set-up time of the output signal (0/90%) 0. s - insulation test voltage.2 kv - limitation of output current 28 ma ± % Nominal reference and operating conditions: - ambient temperature C - supply voltage V or V a.c./d.c. - frequency of the supply voltage Hz - frequency of the input current (voltage) Hz - input voltage Un - power factor (cos fi) input current In - peak factor of the measured current
6 - peak factor of the measured voltage 2 - storage temperature C - air relative humidity (condensation inadmissible) % - external magnetic field A/m - working position any Additional Errors caused by the influence of: - frequency of the input quantity < 0.0 k/ Hz - ambient temperature < 0. k/ C - external magnetic field < 0. k/ A/m. Input overload: Voltage: - short duration 2 Un - long-lasting.2 Un Current: - short duration In - long-lasting.2 In Ensured protection degree: - through the housing IP - from the terminal side IP Dimensions: 4 x x mm Weight: 2 g Compliance to standards: - service security, requirements and tests EN - - insulation ensured by the housing double - insulation between circuits basic - installation category III - pollution level 2 - maximal working voltage in relation to earth 0 V
7 Electromagnetic compatibility: - immunity EN emission EN INSTALLATION. Fixing PP, PP or PB transducers are designed to be installed on a mm DIN rail acc. DIN EN On the external side of the transducer there are screw or self-locking terminal strips enabling the connection of 2. mm 2 external leads (supply and output) and up to. mm 2 leads (input). 4 PP 9 4 mm DIN rail Fig. Overall dimensions and fixing way of the transducer 7
8 .2. Connection diagrams.2.. Measurement of active power in a single-phase network by a PP transducer. a) Direct measurement of single-phase active power Supply Output 9 PP 2 L NorL2 b) Measurement of singlephase active power through a current transformer Supply Output 9 PP 2 L NorL2 S P S2 P2 8
9 c) Measurement of single-phase active power through a current and voltage transformer Supply Output 9 PP 2 a A L NorL2 b S B P S2 P Measurement of active power in a -phase -wire network by a PP transducer (Symmetrically loaded) a) Direct measurement of active power in a -phase -wire network symmetrically loaded Supply Output 9 PP 2 8 L L2 L 9
10 b) Measurement of active power in a -phase -wire network symmetrically loaded through a current transformer Supply Output 9 PP 2 8 L L2 L S P S2 P2 c) Measurement of active power in a -phase -wire network symmetrically loaded through a current and a voltage transformer Supply Output 9 PP 2 8 L a A b B a A b S B P S2 P2 L2 L
11 .2.. Measurement of reactive power in a -phase -wire network by a PP Transducer (Symmetrically loaded) a) Direct measurement of reactive power in a -phase -wire network symmetrically loaded Supply Output 9 PB 8 L L2 L b) Measurement of reactive power in a -phase -wire network symmetrically loaded through a current transformer Supply Output 9 PB 8 L L2 L S P S2 P2
12 c) Measurement of reactive power in a -phase -wire network symmetrically loaded through a current and a voltage transformer Supply Output 9 PB 8 L a A b S B P S2 P2 L2 L. CODING AND ORDERING Coding example: The PP- A-C code means: the execution of a transducer for measurement of active power in a single-phase system, input: In = A, Un = 2 V, nominal power: 0 W, permanent fastening screw terminals, standard execution, without an extra quality inspection certificate. 2
13 Execution codes of PP, PP and PB transducers Table POWER TRANSDUCER - P XX XX X X X X XX X Kind of transducer: measurement of -phase active or reactive power... P measurement of active power in -phase -wire systems, symmetric load... P measurement of reactive power in -phase -wire systems, symmetric load... B Input current: write down the range code (from A to Z and B to Z) from the table 2: A... A 000/ A... Z A... B 000/ A... Z on order* Input voltage: write down the range code (from A to V) from the table 2: /Ö V... A / V... W on order*... 9 Output range: 0... ma, R obc. = W ma, R obc. = W ma, R obc. = W V, R obc. ³ 0 W ma, R obc. = W ma, R obc W V, R obc. ³ 0 W... 7 on order*... 9 Supply: V d.c. or a.c. ( Hz) V d.c. or a.c. ( Hz)... 2 on order*... 9 Kind of terminals: permanent fastening screws... socket - screw plug... 2 socket - self-locking plug... Execution: standard custom-made *... XX Acceptance test: without an extra quality inspection certificate... 0 with an extra quality inspection certificate... acc user s agreement* *... X * Custom-made execution, one must agree with the producer ** The producer will settle the execution code number
14 Un [V] Measurement of single-phase active power Measurement of -phase -wire active or reactive power in a symmetrically loaded network P P B ln/x ; /x /x /x /x /x /x 7/x /x /x 0/x 0/x 400/x 0/x 800/x 0/x 0/x 0/x 00/x 00/x In code Power unit x= x= A B B C C D D E E F F G G H H I I J J K K L L M M N N P P R R S S T T U U V V W kw; kvar Table Un code A B C D E G H I K L M N P R S T U V W
15 7. MAINTENANCE AND GUARANTEE The PP, PP and PB transducers do not require any periodical maintenance. In case of some incorrect unit operations:. In the 8 months period from the date of shipment: One should return the transducer to the LUMEL s Quality Control Dept. If the unit has been used in compliance with the instructions, LUMEL S.A. guarantees to repair it free of charge. The disassembling of the housing causes the cancellation of the granted guarantee. 2. After the guarantee period: One should turn over the transducer to repair it in a certified service workshop. Spare parts are available for the period of ten years from the date of purchase. LUMEL S.A. reserves the right to make changes in design and specifications of any products as engineering advances or necessity requires. 4000/x W W /x X X /x Y Y 0 000/x Z Z MW; 2 Mvar
16 Lubuskie Zak³ady Aparatów Elektrycznych LUMEL S.A. ul. Sulechowska -9 Zielona Góra - Poland Tel.: (48-8) (exchange) Fax: (48-8) lumel@lumel.com.pl Export Department: Tel. (48-8) Fax (48-8) export@lumel.com.pl April 02
TRANSDUCER of TEMPERATURE and STANDARD SIGNALS P20 type
TRANSDUCER of TEMPERATURE and STANDARD SIGNALS P20 type USER S MANUAL Contents 1. APPLICATION...5 2. TRANSDUCER SET...5 3. OPERATIONAL SAFETY...6 4. INSTALLATION...7 4.1. Fitting way...7 4.2. External
More informationSEPARATOR P20G TYPE USER S MANUAL
SEPARATOR P20G TYPE USER S MANUAL 1 2 Contents 1. APPLICATION... 5 2. SEPARATOR SET... 5 3. OPERATIONAL SAFETY... 6 4. FITTING... 7 4.1. Fixing Way... 7 4.2. External Connection Diagrams... 8 5. SERVICE...
More informationPROGRAMMABLE TRANSDUCER OF DC CURRENT AND DC VOLTAGE SIGNALS P20H TYPE
PROGRAMMABLE TRANSDUCER OF DC CURRENT AND DC VOLTAGE SIGNALS P20H TYPE USER S MANUAL 1 2 Contents: 1. APPLICATION... 5 2. TRANSDUCER SET...5 3. OPERATIONAL SAFETY... 6 4. INSTALLATION... 7 4.1. Fixing
More informationDIGITAL PANEL METER N24 AND N25 METER SERIES
DIGITAL PANEL METER N24 AND N25 METER SERIES USER S MANUAL Contents 1. APPLICATION...5 2. METER SET...5 3. OPERATIONAL SAFETY...6 4. INSTALLATION...7 4.1 Fixing Way...7 4.2 External Connection Diagrams...8
More informationRAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL
RAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL 1 Contents 1. Application... 5 2. meter set... 6 3. BASIC REQUIREMENTS, OPERATIONAL SAFETy... 6 4. installation... 10 4.1. Mounting... 10 4.2. External
More informationDIGITAL SYNCHRONIZING UNIT KS3.2 SERVICE MANUAL. 144 x 144 x 77 mm C E R T I F I E D
DIGITAL SYNCHRONIZING UNIT KS3.2 C E R T I F I E D 144 x 144 x 77 mm SERVICE MANUAL 1 CONTENTS 1. APPLICATION... 3 2. DELIVERY SPECIFICATION... 3 3. BASIC SAFETY REQUIREMENTS AND USER S SAFETY... 4 4.
More informationTEMPERATURE CONTROLLER RE21 TYPE
TEMPERATURE CONTROLLER RE21 TYPE USER S MANUAL 1 2 Contents 1. Application... 5 2. Controller set... 5 3. Preparation of the controller to work... 6 3.1. Safety... 6 3.2. Controller installation... 9 3.3.
More informationEA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters
EA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters EA12 EA19 EA17 EA16 EB16 APPLICATION EA16, EB16, EA17, EA19 and EA12 moving-iron meters are intended for measuring AC voltage or
More informationN100. example of application Ethernet www/ ftp. Ethernet TCP IP RS X MeaSUreMent of power network parameters.
cat iii Electrical Safety N100 - power network analyzer Measurement of power network parameters in 3 or 4-wire, balanced or unbalanced systems. two-color led display (red, green). Four quadrant energy
More informationnew! nd30 - METER OF POWER NETWORk PARAMETERS EXAMPlE OF APPliCATiON MEASUREMENT AND ViSUAliZATiON OF POWER NETWORk PARAMETERS
new! cat iii Electrical Safety nd30 - METER OF POWER NETWORk PARAMETERS Measurement of power network parameters in 3- or 4-wire balanced and unbalanced systems. Color graphic display: lcd TFT 3,5, 320
More informationN24, N25 DIGITAL PANEL METER
DIGITAL PANEL METER www.sifamtinsley.co.uk USER S MANUAL Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters DIGITAL PANEL METER Current Transformers
More informationnd30 EXAMPlE OF APPliCATiON MEASUREMENT AND ViSUAliZATiON OF POWER NETWORk PARAMETERS Ethernet www/ ftp Modbus TCP Modbus RS-485
cat iii Electrical Safety nd30 - METER OF POWER NETWORk PARAMETERS Measurement and recording of 54 power network parameters, including current and voltage harmonics up to 51st, in 1-phase 2-wire or 3-phase
More informationnd30pnet - METER Of POwER NETwORk PARAMETERS with profinet EXAMPlE Of APPlICATION MEASUREMENT ANd VISUAlIZATION Of POwER NETwORk PARAMETERS
nd30pnet tri Measurement of 54 power network parameters, including current and voltage harmonics up to 51st, in 1-phase 2-wire or 3-phase 3 or 4-wire balanced and unbalanced systems. graphical color display:
More informationPOWER CONTROLLER RP1 type
Prodaja in zastopa: Materm d.o.o. Morje, morska cesta 6, 2313 Fram tel: 02 608 90 10, www.materm.si POWER CONTROLLER RP1 type USER S MANUAL 2 POWER CONTROLLER RP1 type USER S MANUAL CONTENTS 1. APPLICATION...5
More informationTEMPERATURE CONTROLLER. MOUNTED ON A 35 mm RAIL RE60 TYPE USER S MANUAL
TEMPERATURE CONTROLLER MOUNTED ON A 35 mm RAIL RE60 TYPE USER S MANUAL 1 2 Contents 1. Application... 5 2. Controller set... 5 3. Preparing the controller for opereation... 6 3.1. Security... 6 3.2. Controller
More informationa * example of application MeaSUreMent and ViSUalization of power network parameters Ethernet TCP IP RS-485 USB HOST /SD CARD
3x 0/4...20 ma 8x nd40 ṉ - power network analyzer / recorder Measurement and recording of over 500 electric energy quality parameters acc. to en 50160, en 61000-4-30, en 61000-4-7 standards. Measuring
More informationTHREE-PHASE POWER CONTROLLER RP3 Type
Prodaja in zastopa: Materm d.o.o. Morje, morska cesta 6, 2313 Fram tel: 02 608 90 10, www.materm.si THREE-PHASE POWER CONTROLLER RP3 Type USER S MANUAL 2 THREE-PHASE POWER CONTROLLER RP3 Type USER S MANUAL
More informationHigh power radio transmission module MR03 type
High power radio transmission module MR03 type User s manual CONTENTS 1. APPLICATION...3 2. MR03 MODULE SET...4 3. INSTALLATION...4 3.1 Module assembly...4 3.2 Connection diagrams...5 3.3 Connection way
More informationN30P DIGITAL PANEL METER
N30P DIGITAL PANEL METER Features: NEW Measurement of single-phase network parameters: voltage, current, active, reactive and apparent power, cosj, tgj, j, frequency, active, reactive and apparent energy,
More informationND40 V V. Ethernet www/ ftp / smtp. Ethernet TCP IP RS-485 USB HOST /SD CARD.
ND40 - power network analyzer / recorder Measurement and recording of over 500 electric energy quality parameters acc. to EN 50160, EN 61000-4-30, EN 61000-4-7 standards. Measuring class A - for 3 second
More informationTRANSDUCER OF NETWORK PARAMETERS P43 TYPE
TRANSDUCER OF NETWORK PARAMETERS P43 TYPE USER S MANUAL Contents 1. Application... 5 2. Transducer Set... 6 3. Basic Requirements and Operational Safety... 6 4. Installation... 7 5. Service... 12 6. Archive
More informationTEMPERATURE CONTROLLER RE55 TYPE USER S MANUAL
TEMPERATURE CONTROLLER RE55 TYPE USER S MANUAL CONTENTS 1. APPLICATION...5 2. CONTROLLER SET...5 3. CONTROLLER PREPARATION to WORK...5 3.1. Safety...5 3.2. Controller installation in the panel...6 3.3.
More information4-CHANNEL MODULE OF ANALOG INPUTS SM2 TYPE
4-CHANNEL MODULE OF ANALOG INPUTS SM2 TYPE USER S MANUAL 1 2 CONTENTS 1. APPLICATION...5 2. MODULE SET...6 3. BASIC REQUIREMENTS AND OPERATIONAL SAFETY...6 4. INSTALLATION...9 4.1. Way of fixing...9 4.2.
More informationPOWER NETWORK MEASUREMENTS Analysers, Multimeters & Transducers
POWER NETWORK MEASUREMENTS Analysers, Multimeters & Transducers Measurements of electrical energy and 1 or network parameters belong to the LUMEL s main competence area. We offer in the scope of devices
More informationEnergy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302
Energy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302 Direct connection up to 65 A (WSx10x) Connection with current transformer (WSx30x) Industrial or meters
More information02/11/2015
35 mm - 1 Relay 8A OUR3 Part number 88867103 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
More informationTVA 080 / 100 / 120 / 180 / 200 / 220 Isolation amplifier active
Technical manual BA 0318 Signal converter Isolation amplifier active for galvanic isolation, conversion and adjustment of electrical standard signals Evaluable input signals Direct voltage 0...10V / 0...1V
More information02/11/2015
35 mm - 2 Relays 8A PL2R1 Part number 88867455 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
More informationALPHA 20 MULTIFUNCTION METER (ALPHA SERIES)
Alpha Series www.sifamtinsley.co.uk Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current Transformers Analogue Panel Meters Shunts ALPHA
More informationUSER S MANUAL POWER SUPPLY - ISOLATOR - SIGNAL CONVERTER ZSP 41 POWER SUPPLY - ISOLATOR - SIGNAL CONVERTER SIGNAL MULTIPLIER ZSP 41/2
(ENG) DECEMBER 2017 USER S MANUAL POWER SUPPLY - ISOLATOR - SIGNAL CONVERTER ZSP 41 POWER SUPPLY - ISOLATOR - SIGNAL CONVERTER SIGNAL MULTIPLIER ZSP 41/2 ISOLATOR - SIGNAL CONVERTER TYPE SP 11 CURRENT
More informationN E W functions! Modbus. Wireless transmission - SM ma TCP IP ma. NA5 meter with bargraph. k *
FEATURES: 21 points charact. Password protection INPUT: DC RTC OUTPUT: + - U RS 485 GALVANIC ISOLATION: Zasilanie Ethernet econ Program Ethernet RS 485 RS 485 +48 68 45 75 139/ 233/ 276/ 386 LUMEL S.A.
More informationPOWER NETWORK PARAMETER METER N13 SERVICE MANUAL
POWER NETWORK PARAMETER METER N13 SERVICE MANUAL CONTENTS POWER NETWORK PARAMETER METER - N13 SERVICE MANUAL 1. APPLICATION and PROPERTIES... 3 2. METER SET... 4 3. BASIC REQUIREMENTS - SAFETY INFORMATION...
More informationPRELIMINARY DATA SHEET RI-D140. Three Phase Multifunction DIN Rail Energy Meter (MID Certified) MID
RI-D140 Three Phase Multifunction DIN Rail Energy Meter (MID Certified) Four module DIN rail mounted Energy pulse LED True RMS measurement Cost effective and accurate Modbus communication -/1A or -/5A
More information3 PHASE ENERGY ELECTRONIC METERS MKT & MKT2. (Code to ) INSTRUCTION MANUAL ( M / 00 A ) (c) CIRCUTOR S.A.
3 PHASE ENERGY ELECTRONIC METERS MKT & MKT2 (Code 7 71 071 to 7 71 083) INSTRUCTION MANUAL ( M 981 200 / 00 A ) (c) CIRCUTOR S.A. ----- MKT- MKT2 - ELECTRONIC METERS -------- M-981 200 --- Page Nº 2 3
More informationnew! nd40 example of application MeaSUreMent and ViSUalization of power network parameters Ethernet www/ ftp / smtp Ethernet TCP IP RS-485
new! nd40 - power network analyzer / recorder Measurement and recording of over 500 electric energy quality parameters acc. to en 50160, en 61000-4-30, en 6100-4-7 standards. Measuring class a - for 3
More informationND40 - POWER NETWORK ANALYZER /RECORDER
ND40 - POWER NETWORK ANALYZER /RECORDER EXAMPLE OF APPLICATION 0/4..20 ma Ethernet www/ftp/smtp T Ethernet TCP IP T2 RS-485 Pt00 USB HOST/ SDCARD Pt00 MEASUREMENT AND VISUALIZATION OF POWER NETWORK PARAMETERS
More informationRI-F200 Series. Single and Three Phase Multifunction Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-F200 Series Single and Three Phase Multifunction Energy Meter DIN 96 panel mounted -/1A or -/5A current transformer input Single phase or three phase network compatible Programmable voltage and current
More information08/07/2015
17.5 mm - 1 Solid State Relay 0.7A MUS2 Part number 88827004 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external
More informationSINEAX U 553 Transducer for AC Voltage
With power supply RMS value measurement Carrying rail housing P/0 Application he transducer SINEAX U 55 (Fig. ) converts a sinusoidal or a distorted AC voltage into a load independent DC current or a load
More information22/10/2012
22.5 mm DIN rail mounting TUR1 Part number 88865105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator Option of connecting an external power supply
More informationRISH EM 3490 SS Kilowatt Hour Energy Meter With Rs485 RISH EM 3490 SS. Application : Product Features: Indication: Pulse Indication:
Application : RISH Master 3490 SS is a 96mm x 96mm panel mounted kilowatt hour meter it measures active energy with class 1.0 accuracy having auto-resetting 8 digit seven segment LED counter. The unit
More informationApplication Alpha 20 Measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel meters
Technical Data Sheet Alpha 20 Alpha 20 is a compact multifunction instrument which Measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel
More informationMeasuring Transducer MT4xx series Programmable AC Current Transducer MT418
Measuring Transducer MT4xx series Programmable AC Current Transducer MT418 o RMS AC current or frequency measurements o Current auto range measurements up to 12 A o Frequency measurement range 16 400 Hz
More informationMOVING-IRON METERS EA16, EB16, EA17, EA19, EA12 TYPES
MOVING-IRON METERS EA16, EB16, EA17, EA19, EA12 TYPES AMMETERS and VOLTMETERS EA12 EA19 EA17 EA16 EB16 EA16, EB16, EA17, EA19 and EA12 moving-iron meters are intended for measuring AC voltage or AC current.
More informationPowerLogic power-monitoring units. PM700 series power meter. Technical data sheet
PowerLogic power-monitoring units PM700 series power meter Technical data sheet 2009 Functions and characteristics The PowerLogic PM700 series power meter offers all the measurement capabilities required
More informationData Sheet 066.8e. Transducers for Active and Reactive Power EW+B 2.2 DGW+B 2.2 VGW+B 2.2 DUW+B 2.2 VUW+B 2.2
Data Sheet 066.8e Transducers for Active and Reactive Power EW 2.2 DGW 2.2 VGW 2.2 DUW 2.2 VUW 2.2 Application The E/DG/VG/DU/VU W 2.2 power transducers convert all forms of active and reactive power polarity
More informationMeasuring centers MC3x0 series Energy Meters with Power Display Energy Meter WQ0217 & WQ1217 Energy Meter with analogue pointer WQ0207 & WQ2207
Measuring centers MC3x0 series Energy Meters with Power Display Energy Meter WQ0217 & WQ1217 Energy Meter with analogue pointer WQ0207 & WQ2207 o 7 digits electromechanical register o Up to 2 registers
More informationRI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
More informationEA16, EB16, EA17, EA19
MOVING-IRON METERS EA16, EB16, EA17, EA19 and EA12 TYPES AMMETERS and VOLTMETERS CATEGORIES OF METER CLIMATIC VERSIONS If it is not written otherwise in the order, these meters are intended to use in moderate
More information08/07/2015
17.5 mm - 1 Relay 8A MUR1 Part number 88827105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external load connection
More information27/04/2015
Modular Carril DIN 35 mm HIL Part number 84871120 Control of AC and DC currents Automatic recognition of AC/DC Measurement ranges from 2 ma to 10 A Choice between over and undercurrent True RMS measurement
More informationDATA SHEET Selectable AC transducer TAS-311DG
DATA SHEET Selectable AC transducer Measuring on AC networks Class 0.5 (IEC688) measurement Supply/measur. voltage up to 690 V Easy configuration via PC interface possible DEIF A/S Frisenborgvej 33 DK-7800
More information02/11/2015
DIN Rail Mount 17.5 mm MXR1 Part number 88826185 Just one digit differentiates the new range part number from the old range's Previous part number : 88 826 XXX / new part number : 88 827 XXX Part numbers
More informationNotes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 320VAC 360VAC 400VAC 400VAC
Features DIN-Rail 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection Parallel
More informationMCR-SL-CUC Universal current transducer. Data sheet _en_05. 1 Description
Universal current transducer Data sheet 104059_en_05 PHOENIX CONTACT 2011-03-09 1 Description MCR-SL-CUC-...-I and MCR-SL-CUC-...-U active current transducers convert DC, AC, and distorted currents into
More information12/2 Product overview. 12/3 7KT1 14, 7KT1 53 E-counters. 12/9 7KT1 11, 7KT1 12 digital measuring devices. 12/11 7KT1 0 analog measuring devices
BETA Measuring /2 Product overview /3 7KT1 14, 7KT1 53 E-counters /9 7KT1 11, 7KT1 digital measuring devices /11 7KT1 0 analog measuring devices / 7KT5 8 time and pulse counters /14 7KT5 5, 7KT5 6 time
More information400,440Vac Vdc V, A, W, VA, var, Hz, V, Avg. A cos phi, sin phi and phi measurement kwh, kvarh (via Pulse Output)
MODEL EM4000ACF Multifunction Transducer for alternating voltage and current Power supply voltages: Suitable for DIN-rail mounting 85 240Vac 400,440Vac 24 65Vdc 100..330Vdc V, A, W, VA, var, Hz, V, Avg.
More informationHigh precision measurement system for current and voltage IHC-A/B-RM01/03
Measurement Offset-free and low-noise 16 bit data acquisition system ISA-ASIC Internal sample rate 3,500 Hz Communication Standard RS232- or RS485 interface Advantages Direct measurement on the bus bar
More informationRISH EM 3490 DS Dual Source Energy Meter (With All Display Parameters) RISH EM 3490 DS. Application : Product Features:
(With All Display Parameters) Application : RISH EM 3490 DS measures important electrical parameters of Utility (in normal mode) & Generators (in Power back up) in three phase and single phase Network
More informationPOWER NETWORK PARAMETER ANALYSER N10
POWER NETWORK PARAMETER ANALYSER N10 SERVICE MANUAL 2 POWER NETWORK PARAMETER ANALYSER N10 Service manual 1. APPLICATION... 5 2. METER SET... 5 3. INSTALLATION... 6 3.1. FITTING... 6 3.2. EXTERNAL CONNECTION
More informationJewell DPM Power / Power Factor Size 96/96 BEST IN CLASS
Application: The Jewell DPM Power 96x96 series measures system active Power (Import/Export), Reactive Power (Import/Export), Apparent Power & Power Factor of Three Phase and Single Phase Network. It has
More informationTheta 20A / 20V. Technical Data Sheet. Special Features
Technical Data Sheet Theta 20A / 20V Theta 20A / 20V is used to measure and convert AC Voltage or Current input into a load independent DC current or voltage output signal. Special Features Available in
More informationProgrammable AC Current Transducer MT418
Programmable AC Current Transducer MT418 RMS AC current measurements Current auto range measurements up to 12 A Frequency measurement range 16 400 Hz AC or universal wide auiliary power supply range 24
More informationPhase control Single function phase control relay - 7.5 mm Control of -phase networks: phase sequence, total phase failure Multi-voltage from x 08 to x 480 V Controls its own supply voltage True RMS measurement
More informationn True RMS measurement n Fully onsite programmable input voltage range (for CIP-V)
Tranducers for alternating current/voltage n True RMS measurement n Fully onsite programmable input voltage range (for CIP-V) and input current range (for CIP-I) n Available in single or dual output type
More informationNotes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 400VAC
Features DIN-Rail Description 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection
More informationDT1100 xx xx xx PS. Isolators, Isolator / Power Supplies. Operating Instructions
Isolators, Isolator / Power Supplies Operating Instructions EN Contents 1. About this document...4 1.1. Function... 4 1.2. Target group... 4 1.3. Symbolism used... 4 2. For your safety...5 2.1. Authorized
More information02/11/2015
DIN Rail Mount 17.5 mm MURc3 Part number 88826503 DIN Rail Mount 17.5 mm MURc3 Part number 88826503 Just one digit differentiates the new range part number from the old range's Previous part number : 88
More informationRISH Master Digital Multifunction Instrument with onsite pluggable output options. Application : Product Features:
Application : RISH Master 3430 measures important electrical parameters in 3 phase and single phase Network & replaces the multiple analog panel meters. It measures electrical parameters like AC current,
More informationDEIF A/S. TAS-311DG Selectable AC transducer J (UK) Installation and start up instructions
Installation and start up instructions TAS-311DG Selectable AC transducer Voltage, current, frequency or phase angle transducer Supply voltage up to 690V DEIF A/S Configuration via PC-interface possible
More informationALPHA 50 MULTIFUNCTION METER (ALPHA SERIES)
Alpha Series www.sifamtinsley.co.uk Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current Transformers Analogue Panel Meters Shunts ALPHA
More informationSeries P. Applications
Ratings 25 800 VA Voltage Primary 230 / 400 / 460 V range Secondary 6 / 12 V 12 / 24 V 24 / 48 V 115 / 230 V Voltage selection by means of metal connection bridges, offering the full rated power at any
More information11/03/2013
17.5 mm DIN rail mounting MUR1 Part number 88826105 TO BE SOON REPLACED BY THE NEW CHRONOS 2 RANGE (ref. 88827...) Relay or solid state output Multi-function or mono-function Multi-range Multi-voltage
More informationRISH Master 3430 DIGITAL MULTI-FUNCTION TRANSDUCER. Electro-Meters
measures important electrical parameters in phase and single phase etwork & replaces the multiple analog panel meters. It measures electrical parameters like AC current, Voltage, frequency, Power, Energy
More informationPIR6WT-1Z interface - time relays
1 9-functions electronic time relays compliance with standard PN-EN 612-1 Time relay PIR6WT-1Z consists of: - universal socket with electronic PI6WT-1Z with screw terminals, - changeover relay RM699V,
More informationAMIK 200 / 201 Technical Data Sheet
AMIK 200 / 201 Technical Data Sheet AMIK Special Features MODBUS (RS-485) Communication available only on Amik 201 On site Programmable CT/PT Ratios User selectable CT Secondary 1A/5A User selectable PT
More informationTransducing electrical quantities Iskra MIS d.d. Measuring Transducers. Features
Measuring Transducers Transducing electrical quantities Iskra MIS d.d. Measuring Transducers Features AC, DC POWER SYSTEM MEASUREMENT MICROPROCESSOR CONTROL HOUSING FOR DIN RAIL MOUNTING IN COMPLIANCE
More informationPrecipition Sensor with analogue Intensity Output ,
THE WORLD OF WEATHER DATA - THE WORLD OF WEATHER DATA - THE WORLD OF WEATHER DATA Instruction for use 021335/11/09 Precipition Sensor with analogue Intensity Output 5.4103.20.041, 5.4103.20.741 ADOLF THIES
More informationProgrammable AC Voltage Transducer MT416
Programmable AC Voltage Transducer MT416 RMS AC voltage or frequency measurements Voltage auto measurements up to 600 V L-N Frequency measurement 16 400 Hz AC or universal wide auiliary power 24 300 Vdc,
More informationPART NUMBERING SYSTEM
Plug-In Timer 11 pins Multifunction or monofunction Compact body for space saving Wide time range (from 0.5 seconds to 10 days delay) Universal power supply (12-240 Vz) 1 or 2 relay outputs (SPDT / Changeover)
More informationSINEAX I 552 Transducer for AC current
SNEAX 55 With power supply RMS value measurement, with measuring ranges Carrying rail housing P/0 Application he transducer SNEAX 55 (Fig. ) converts a sinusoidal or a distorted AC current into a load
More informationEMBSIN 281 G Power factor transducer
EMBSI 8 G Carrying rail housing MBS/SP Application The transducer EMBSI 8 G (Fig. ) measures the power factor between current and voltage of a single or 3-phase balanced network having a sine wave form.
More informationV2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC
P AC/DC voltage monitoring Multifunction Supply voltage 24 V DC or 230V AC/DC Supply circuit = Measuring circuit 1 change-over contact Width 22,5 mm Control elements Tripping delay Maximum threshold Minimum
More information24/07/2012
17.5 mm DIN rail mounting MURc3 Part number 88826503 Relay or solid state output Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version)
More informationTheta Hz. Technical Data Sheet. Special Features
Technical Data Sheet Theta Hz Theta Hz the transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent
More informationDT1100 E xx xx (PS) Galvanic Isolators. Operating Instructions
DT1100 E xx xx (PS) Galvanic Isolators Operating Instructions Contents 1. About this document...4 1.1. Function... 4 1.2. Target group... 4 1.3. Symbolism used... 4 2. For your safety...5 2.1. Authorized
More informationFeatures. Regulated Converter RAC05- SK/C14. RAC 5 Watt Single Output RAC05-3.3SK/C14. AC/DC Converter
Features Regulated Converter Unique, patent-pending design Isolated power supply with integrated mains filter Packaged inside of line filter case Safe, touchable DC outputs Easy installation Worldwide
More information02/11/2015
17.5 mm - 1 Relay 5A EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer
More informationTRIO-PS/1AC/24DC/ 5. Extract from the online catalog. Order No.:
Extract from the online catalog TRIO-PS/1AC/24DC/ 5 Order No.: 2866310 DIN rail power supply unit, primary-switched mode, 1-phase, output: 24 V DC / 5 A Commercial data EAN 4046356046640 Pack 1 pcs. Customs
More informationMETRATESTER 5+ Tester for DIN VDE /6.15
3-348-817-03 15/6.15 Applications Electrical safety testing of electrical equipment: per DIN VDE 0701-0702: 2008 by means of measurement of: Protective conductor resistance Insulation resistance Protective
More informationInstallation and Operational Instructions for ROBA -multiswitch Type 019._00.2
Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EU Low Voltage Directive 2014/35/ EU and the Electromagnetic Compatibility (EMC)
More informationMETRAClip87 and 88 Clamp Multimeters
3-349-795-03 1/7.14 Current and frequency measurement via clamp meter: METRAClip87: 1500 A AC TRMS and 1500 A DC METRAClip88: 2000 A AC TRMS and 3000 A DC Multimeter functions via connector sockets: V
More informationSINEAX G 536 Phase Angle or Power Factor Transducer
SIEAX G Carrying rail housing P/0 Application The transducer SIEAX G (Fig. ) measures the phase angle or power factor between current and voltage of a single or -phase balanced network having a sine wave
More informationN. TEST TEST DESCRIPTION
Multi function system for testing substation equipment such as: current, voltage and power transformers, all type of protection relays, energy meters and transducers Primary injection testing capabilities
More informationZelio Control Measurement Relays
Selection Guide Application Voltage control Current control Functions 3-phase Single-phase and d.c. Integrated current transformer - Overvoltage and between phases - Overvoltage and between phases and
More informationInstallation and Operational Instructions for ROBA -switch Type 017._00.2
OBA -switch Type 017._00.2 Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EC Low Voltage Directive 2014/35/ EC and the EMC Directive
More informationType Nominal voltage (V) Code HSV V
Speed control Speed control relay - mm Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - -wire PNP or NPN, Namur, voltage 0-0V or volt-free contact type Works
More informationUNIVERSAL MEASURING INSTRUMENTS. TNM 34xx. TNM 3410 / 3420 / 3430 / 3440 Universal measuring instrument 1/49
TNM 3410 / 3420 / 3430 / 3440 Universal measuring instrument True RMS measurement User-friendly programing Four different types for optimal specification RS485 interface For 3- or 4-wire connection Compact
More informationTheta 60R. Technical Data Sheet. Special Features. Fig. 2 Theta R, 2 channel version, in housing S17 hole mounting brackets pulled out.
Technical Data Sheet Theta 60R 60 R 60 R Fig. Theta R, channel version, in housing S7 clipped on to a top - hat rail. Fig. Theta R, channel version, in housing S7 hole mounting brackets pulled out. Theta
More informationV2IM10AL10 Art.Nr.: V2IM10AL10P Art.Nr.: Control element. Tripping delay. Function selector. Status indication 24...
P AC/DC current monitoring Multifunction Supply voltage 24-240V DC or 110-240V AC 1 change-over contact Width 22,5 mm Control element Tripping delay Maximum threshold Minimum threshold Function selector
More information