Photo: HBD-E3100 SPECIFICATIONS. Inputs (Analog)

Transcription

1 SERVICE MANUAL Ver..7.6 HBD-E is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN, Bluetooth, NFC and FM tuner section in BDV-E. HBD-E is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN, Bluetooth, NFC and FM tuner section in BDV-E. HBD-E is the amplifier, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN, Bluetooth, NFC and FM tuner section in BDV-E. HBD-E is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN, Bluetooth, NFC and FM tuner section in BDV-E. HBD-E6 is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN, Bluetooth, NFC and FM tuner section in BDV-E6. Model Name Using Similar Mechanism Mechanism Type Optical Pick-up Block Name HBD-E/E/E/E/ E6 Photo: HBD-E BDP-S BPX-7 KEM8AAA US Model HBD-E/E Canadian Model Singapore Model HBD-E/E/E/E6 AEP Model Taiwan Model HBD-E/E/E6 UK Model HBD-E/E/E Chinese Model HBD-E/E6 E Model HBD-E/E/E/E/E6 Argentina Model BDV-E/E Australian Model HBD-E/E6 Russian Model Saudi Arabia Model Thai Model HBD-E/E/E6 South African Model HBD-E/E/E6 PX Model HBD-E Amplifier Section US model only: AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC) Front L + Front R: F8-.6 With ohms loads, both channels driven, from 8 Hz -, Hz; rated watts per channel minimum RMS power, with no more than % total harmonic distortion from milliwatts to rated output. BDV-E6/BDV-E/BDV-E/BDV-E BDV-E (Except UK model): POWER OUTPUT (rated) Front L/Front R: POWER OUTPUT (reference) Front L/Front R/Surround L/Surround R: 7 W + 7 W (at ohms, khz, % THD) W (per channel at ohms, khz) W (at 6 ohms, khz) W (at 6 ohms, 8 Hz) Center: Subwoofer: Inputs (Analog) AUDIO IN Sensitivity: V/ mv MIC / Sensitivity: mv (Singapore model) Inputs (Digital) TV (Audio Return Channel/OPTICAL) Supported formats: LPCM CH (up to 8 khz), Dolby Digital, DTS BDV-E (UK model) POWER OUTPUT (rated) Front L/Front R: POWER OUTPUT (reference) Front L/Front R/Surround L/Surround R: 7 W + 7 W (at ohms, khz, % THD) W (per channel at ohms, khz) Center: W (at 6 ohms, khz) Subwoofer: W (at 6 ohms, 8 Hz) BDV-E/ BDV-E6 (Chinese model) POWER OUTPUT Front L/Front R/Surround L/Surround R: 7 W (per channel at ohms, khz) Sony Corporation Published by Sony EMCS (Malaysia) PG Tec SPECIFICATIONS Center: W (at 6 ohms, khz) Subwoofer: W (at 6 ohms, 8 Hz) Inputs (Analog) AUDIO IN Sensitivity: V/ mv Inputs (Digital) TV (Audio Return Channel/OPTICAL) Supported formats: LPCM CH (up to 8 khz), Dolby Digital, DTS HDMI Section Connector Type A (9 pin) BD/DVD/CD System Signal format system NTSC/PAL (except US, PX and Canadian models) NTSC (US, PX and Canadian models) USB Section (USB) port: Type A (For connecting USB memory, memory card reader, digital still camera, and digital video camera) LAN Section LAN () terminal BASE-TX Terminal Wireless LAN Section Standards Compliance Frequency and Channel Frequency band IEEE 8. b/g/n US, Canadian, Argentina and Taiwan models:. GHz band: channels Other models:. GHz band: channels. GHz -.8 GHz Bluetooth Section Communication system Bluetooth Specification version. Output Bluetooth Specification Power Class Maximum communication range Line of sight approx. m ) (except US, PX and Canadian models) Line of sight approx. m (ft) ) (US, PX and Canadian models) Frequency band. GHz band. GHz -.8 GHz Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible Bluetooth profiles ) ADP. (Advanced Audio Distribution Profile) AVRCP. (Audio Video Remote Control Profile) Supported Codecs ) SBC ), AAC Transmission range (ADP) Hz, Hz (Sampling frequency. khz, 8 khz) ) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, antenna s performance, operating system, software application, etc. ) Bluetooth standard profiles indicate the purpose of Bluetooth communication between devices. ) Codec: Audio signal compression and conversion format ) Subband Codec BLU-RAY DISC/DVD RECEIVER

2 HBD-E/E/E/E/E6 Ver.. FM Tuner Section System Tuning range Antenna (aerial) General Power requirements Power consumption PLL quartz-locked digital synthesizer 87. MHz - 8. MHz ( khz step) (except US, PX and Canadian models) 87. MHz - 8. MHz ( khz step) (US, PX and Canadian models) FM wire antenna (aerial) US and Canadian models: VAC, 6 Hz Taiwan model: V AC, /6 Hz Latin-American, V AC area in E model and PX models: V V AC, /6 Hz Saudi Arabia model: 7 V V AC, /6 Hz Other models: V V AC, /6 Hz On: 9 W Standby:. W Dimensions (w/h/d) (approx.) mm. mm 96 mm (7 in in ¾ in) incl. projecting parts Mass (approx.).7 kg ( lb 6 oz) Design and specifications are subject to change without notice. Standby power consumption:. W. Over 8% power efficiency of amplifier block is achieved with the full digital amplifier, S-Master. This system incorporates with Dolby* Digital and Dolby Pro Logic adaptive matrix surround decoder and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-d symbol are trademarks of Dolby Laboratories. ** Manufactured under license under U.S. Patent Nos:,96,67;,97,8; 6,6,66; 6,87,; 7,,87; 7,,99; 7,9,9; 7,7,67 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved. This system incorporates High-Definition Multimedia Interface (HDMI TM ) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Java is a trademark of Oracle and/or its affiliates. DVD logo is a trademark of DVD Format/ Logo Licensing Corporation. Blu-ray Disc, Blu-ray, Blu-ray D, BD-LIVE, BONUSVIEW, and logos are trademarks of the Blu-ray Disc Association. Blu-ray Disc, DVD+RW, DVD-RW, DVD+R, DVD-R, DVD VIDEO, and CD logos are trademarks. BRAVIA is a trademark of Sony Corporation. AVCHD D/Progressive and the AVCHD D/Progressive logo are trademarks of Panasonic Corporation and Sony Corporation., XMB, and xross media bar are trademarks of Sony Corporation and Sony Computer Entertainment Inc. Playstation is a registered trademark of Sony Computer Entertainment Inc. Sony Entertainment Network logo and Sony Entertainment Network are trademarks of Sony Corporation. Music and video recognition technology and related data are provided by Gracenote. Gracenote is the industry standard in music recognition technology and related content delivery. For more information, please visit CD, DVD, Blu-ray Disc, and music and video-related data from Gracenote, Inc., copyright -present Gracenote. Gracenote Software, copyright -present Gracenote. One or more patents owned by Gracenote apply to this product and service. See the Gracenote website for a nonexhaustive list of applicable Gracenote patents. Gracenote, CDDB, MusicID, MediaVOCS, the Gracenote logo and logotype, and the Powered by Gracenote logo are either registered trademarks or trademarks of Gracenote, Inc. in the United States and/or other countries. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. Content owners use Microsoft PlayReady content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReady-protected content and/or WMDRM-protected content. If the device fails to properly enforce restrictions on content usage, content owners may require Microsoft to revoke the device s ability to consume PlayReady-protected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. Opera Devices SDK from Opera Software ASA. Copyright 99- Opera Software ASA. All rights reserved. All other trademarks are trademarks of their respective owners. Other system and product names are generally trademarks or registered trademarks of the manufacturers. and marks are not indicated in this document. End User License Information Gracenote End User License Agreement This application or device contains software from Gracenote, Inc. of Emeryville, California ( Gracenote ). The software from Gracenote (the Gracenote Software ) enables this application to perform disc and/or file identification and obtain music-related information, including name, artist, track, and title information ( Gracenote Data ) from online servers or embedded databases (collectively, Gracenote Servers ) and to perform other functions. You may use Gracenote Data only by means of the intended End-User functions of this application or device. You agree that you will use Gracenote Data, the Gracenote Software, and Gracenote Servers for your own personal non-commercial use only. You agree not to assign, copy, transfer or transmit the Gracenote Software or any Gracenote Data to any third party. YOU AGREE NOT TO USE OR EXPLOIT GRACENOTE DATA, THE GRACENOTE SOFTWARE, OR GRACENOTE SERVERS, EXCEPT AS EXPRESSLY PERMITTED HEREIN. You agree that your non-exclusive license to use the Gracenote Data, the Gracenote Software, and Gracenote Servers will terminate if you violate these restrictions. If your license terminates, you agree to cease any and all use of the Gracenote Data, the Gracenote Software, and Gracenote Servers. Gracenote reserves all rights in Gracenote Data, the Gracenote Software, and the Gracenote Servers, including all ownership rights. Under no circumstances will Gracenote become liable for any payment to you for any information that you provide. You agree that Gracenote, Inc. may enforce its rights under this Agreement against you directly in its own name. The Gracenote service uses a unique identifier to track queries for statistical purposes. The purpose of a randomly assigned numeric identifier is to allow the Gracenote service to count queries without knowing anything about who you are. For more information, see the web page for the Gracenote Privacy Policy for the Gracenote service. The Gracenote Software and each item of Gracenote Data are licensed to you AS IS. Gracenote makes no representations or warranties, express or implied, regarding the accuracy of any Gracenote Data from in the Gracenote Servers. Gracenote reserves the right to delete data from the Gracenote Servers or to change data categories for any cause that Gracenote deems sufficient. No warranty is made that the Gracenote Software or Gracenote Servers are error-free or that functioning of Gracenote Software or Gracenote Servers will be uninterrupted. Gracenote is not obligated to provide you with new enhanced or additional data types or categories that Gracenote may provide in the future and is free to discontinue its services at any time. GRACENOTE DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NON-INFRINGEMENT. GRACENOTE DOES NOT WARRANT THE RESULTS THAT WILL BE OBTAINED BY YOUR USE OF THE GRACENOTE SOFTWARE OR ANY GRACENOTE SERVER. IN NO CASE WILL GRACENOTE BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY LOST PROFITS OR LOST REVENUES. Gracenote, Inc. 9 Wi-Fi, Wi-Fi Protected Access and Wi-Fi Alliance are registered marks of the Wi-Fi Alliance. Wi-Fi CERTIFIED, WPA, WPA and Wi-Fi Protected Setup are marks of the Wi-Fi Alliance. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android is a trademark of Google Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. MPEG Layer- audio coding technology and patents licensed from Fraunhofer IIS and Thomson. This product incorporates proprietary technology under license from Verance Corporation and is protected by U.S. Patent 7,69,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright - Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CAUTION Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiation exposure. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

3 HBD-E/E/ E/E/E6 Ver.. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed. ma ( microamperes.). Leakage current can be measured by any one of three methods.. A commercial leakage tester, such as the Simpson 9 or RCA WT-A. Follow the manufacturers instructions to use these instruments.. A battery-operated AC milliammeter. The Data Precision digital multimeter is suitable for this job.. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is.7 V, so analog meters must have an accurate low-voltage scale. The Simpson and Sanwa SH-6Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set. μf. kω AC voltmeter (.7 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage.

4 HBD-E/E/E/E/E6 Ver.. TABLE OF CONTENTS. SERVICING NOTES.... DISASSEMBLY -. Disassembly Flow How To Bend FFC Case Panel Loading Assy Front Panel Assy BD Drive (BPX-7) POWER KEY Board, WLAN/BT COMBO Card, KARAOKE Board (SP, RU), PANEL Board MB Board AMP Board SWITCHING REGULATOR (SWR) Optical Pick-up Block (KEM8AAA), Wire (Flat Type).... TEST MODE Printed Wiring Board - PANEL Board Schematic Diagram - PANEL Board Printed Wiring Board - KARAOKE Board (SP, RU) Schematic Diagram - KARAOKE Board (SP, RU) Printed Wiring Board - POWER KEY Board Schematic Diagram - POWER KEY Board EXPLODED VIEWS 7-. Case Section Front Panel Section Chassis Bottom Section Chassis Section BD Drive Section (BPX-7) ELECTRICAL PARTS LIST ELECTRICAL CHECK.... TROUBLESHOOTING DIAGRAMS 6-. Block Diagram - SERVO Section Block Diagram - MEMORY/HDMI Section Block Diagram - MAIN Section Block Diagram - AMP Section Block Diagram - POWER SUPPLY Section Printed Wiring Board - MB Board (Component Side) Printed Wiring Board - MB Board (Conductor Side) Schematic Diagram - MB Board (/6) Schematic Diagram - MB Board (/6) Schematic Diagram - MB Board (/6) Schematic Diagram - MB Board (/6) Schematic Diagram - MB Board (/6) Schematic Diagram - MB Board (6/6) Printed Wiring Board - AMP Board (Component Side) Printed Wiring Board - AMP Board (Conductor Side) Schematic Diagram - AMP Board (/) Schematic Diagram - AMP Board (/) Schematic Diagram - AMP Board (/) -... This appliance is classified as a CLASS R LASER product. Visible and invisible laser radiation is emitted when the laser protective housing is opened, so be sure to avoid direct eye exposure. This marking is located on the laser protective housing inside the enclosure. This appliance is classified as a CLASS LASER product. This marking is located on the rear exterior. The nameplate is located on the bottom exterior. NOTES ON CHIP COMPONENT REPLACEMENT Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. FLEXIBLE CIRCUIT REPAIRING Keep the temperature of soldering iron around 7 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within times). Be careful not to apply force on the conductor when soldering or unsoldering.

5 HBD-E/E/E/E/E6 SECTION Ver.. SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than cm away from the objective lens. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. RELEASING THE DISC TRAY LOCK The disc tray lock function for the antitheft of an demonstration disc in the store is equipped. Releasing Procedure:. Press the [?/] button to turn on the system.. Touch the [FUNCTION] sensor to select BD/DVD.. Touch the [x] and [Z] sensors simultaneously and hold down until D. OFF displayed on the fluorescent indicator tube (around seconds). Note: When D. LOCK is displayed, the disc tray lock is not released by turning power on/off with the [?/] button. ABOUT THE LENS CLEANING Do not do the lens cleaning with the cotton bud etc. It causes the trouble. NOTE OF REPLACING THE IC, IC, IC, IC, IC, IC6, IC76, IC8 AND IC ON THE MB IC, IC, IC, IC, IC, IC6, IC76, IC8 and IC on the MB board cannot exchange with single. When these parts on the MB board are damaged, exchange the entire mounted board. NOTE OF REPLACING THE IC AND IC ON THE MB Replacement of IC and IC on the MB board used in this unit requires a special tool. TEST DISC Part No. Description Layer J A BLX- Single Layer J-69--A BLX- Dual Layer J--7-A CD (HLX-A) J---A HLX- Single Layer (NTSC) J--6-A HLX- Dual Layer (NTSC) J A HLX-6 Single Layer (PAL) J A HLX-7 Dual Layer (PAL) Note: Refer to the service manual of BDP-BX/S (Part No []) (page - to -E) for the use of BLX-/. Operation and Display:. BLX- Procedure:. Select.976Hz/8p.. Play.Motion picture.. Check whether player can play back or not.. Check each outputs. Video: Composite/S Video/component/HDMI. Audio: Speaker out. * When 8/p monitor is nothing, 8i (9.9Hz or Hz) can use instead of 8/p. However this is temporary correspondence.. BLX- Procedure:. Select 8i (9.9Hz or Hz).. Play.Motion picture.. Check whether player can play back or not (Check the picture and sound output).. CD (HLX-A) Procedure: Check whether player can play back or not (Check the sound output).. HLX-/ (NTSC), HLX-6/7 (PAL) Procedure:. After displayed Main Menu, select.video Signal.. Play.Color bar % (Check the picture and sound output).. Return to Menu.. Play Demonstration : or Demonstration 6:9 (Check the picture and sound output).

6 HBD-E/E/E/E/E6 Ver.. NOTE OF REPLACING THE OPTICAL DEVICE (KEM8AAA) OR MB The password will be supplied to only service HQ, and service center name, q ty and all of software registered information should be maintained by service HQ, and Audio will ask to report the registration information. Optical device (KEM8AAA) for BD requires precise read out functions and secure contents protection system for more than past DVD/CD. Therefore, in the case repaired as follows, the writing work of the OP data is necessary. When the optical device (KEM8AAA) is replaced (The MB board doesn t replace). When both the optical device (KEM8AAA) and MB board are replaced. When the MB board is replaced (The optical device (KEM8AAA) doesn t replace) (In this case, do the work of. Optical device (KEM8AAA) replacement other than the replacement of new optical device). Note: The servo adjustment is done while writing the OP data. The manual adjustment is unnecessary. LD ON TIME history doesn t carry over. Do not touch any optical block parts, turn table and during replacing. BD laser diode is very sensitive.. Preparation -. ESD Countermeasure It is necessary to confirm the state of static electricity in the work space before the repair is started. The static electricity resistance of the BD laser is weaker than that of the DVD/CD laser. Do work space and worker s ESD countermeasures to prevent destruction by ESD. -. Jig Digital camera (Recommend with macro mode) USB memory PC Barcode decoder (Refer to -. Barcode decoder (BDPRdec) ) -. Barcode decoder (BDPRdec) Jig name : BDPRdec.exe Release :.8. Version :... Software contents : BDPRdec.exe : Barcode decoder software SavePath.ini : Decoded file destination setting file (Initial destination is C:\BD\BuData.txt ) TasmanBars.dll : Decode dll Uninst.exe : Uninstall the BDPRdec.exe from PC Install procedure:. Unzip the barcode decoder files to any PC folder.. Check the attached D code photo (OK_sample.JPG) drag & drop onto BDPRdec.exe. When the barcode decoder is used for the first time, the password is necessary. It is unnecessary since the second times. Note : The password will be supplied to only service headquarters, and service center name/q ty/all of software registered information should be maintained by service headquarters. Note : Do not change the decoded file name BuData.txt.. When.NET frame work requirements is displayed, download following applications from Microsoft download site. Microsoft.NET Framework Version. Redistributable Package (x86) g=en&familyid=86eacb-6-bd-8edd-aabcef Microsoft.NET Framework. Service Pack (x86) g=en&familyid=79bcb77-ec-ad-aacf-a76f76ba How to use: Case Drag & drop D code photo onto BDPRdec.exe. Case Drag & drop BU data file onto BDPRdec.exe. Data file name be changed to specify format and end of 7 character are defined. You can also enter the file path at the prompt. 6

7 HBD-E/E/E/E/E6 Ver... Pass-fail judgment of the optical device (KEM8AAA) Perform pass-fail judgment to judge whether the repair of the optical device (KEM8AAA) is necessary. -. Flow of drive section check Confirm whether BD (BLX-) can be reproduced YES NO Confirm whether the drive voltage is the following values Q pin : V Q6 pin : V NO Confirm F, F, F on the MB board, and replace it when it is open. YES Confirm OP FFC cable (Part No ) and SPD FFC cable (Part No ), and replace it when it has been damaged Then, confirm whether this unit operates normally NO Confirm whether the optical device IOP is normal in the service mode (Refer to -. Flow of optical device IOP check ) NO Replace the optical device (KEM8AAA) (Refer to. Optical device (KEM8AAA) replacement ) YES Confirm whether DVD (HLX-)/ CD (HLX-A) can be reproduced NO OK Note: Refer to -. OPTICAL PICK-UP BLOCK (KEM8AAA), WIRE (FLAT TYPE) (page ) about how to remove the COVER, DRIVE. -. Flow of optical device IOP check Turn the power on, and change function to BD/DVD Press the buttons on the remote commander in order of [DISPLAY], [], [], [] [SUBTITLE], and enter the service mode Confirm whether value is the specification value Specification value: BD : ±6 ma DVD/CD: ±9 ma YES OK NO Replace the optical device (Refer to. Optical device (KEM8AAA) replacement ) Press the buttons on the remote commander in order of [8], [7], [], [ ], and the diop value is displayed 7

8 \/ \/ HBD-E/E/E/E/E6 Ver... Optical device (KEM8AAA) replacement Flow of replacement: Note: The photo in flow is an image. Barcode label on new optical device (KEM8AAA) bottom side Save the text data to USB memory (memory capacity need not be 8GB) Connect USB memory with front USB connector on this unit, and read the text data by the service mode Take photo (JPEG) by digital camera Change photo into the text data with the barcode decoder Procedure:. Remove the INSULATOR ( pieces) and broken optical device (KEM8AAA) from LOADING ASSY.. Take photo of the barcode on new optical device (KEM8AAA) bottom side by digital camera. Front view (E) (E/E/E6) Front USB connector Front USB connector. Assemble the INSULATOR ( pieces) to new optical device (KEM8AAA), fix (Torque value: kgf) it to LOADING ASSY with screw, and assemble this unit.. Drag & drop the taken photo by step to BDPRdec.exe, and make the text data (File name: BuData.txt).. Save the text data to USB memory. 6. Connect USB memory with front USB connector on this unit, and turn the power on. 7. Press the [FUNCTION] button on the remote commander to select BD/DVD. 8. Press the buttons on the remote commander in order of [DISPLAY], [], [], [], [SUBTITLE], and enter the service mode. 9. Press the buttons on the remote commander in order of [8], [], [ENTER], and execute [] Drive OP data Write. BDV must select Mode.. Turn the power off after writing the OP data.. Turn the power on, and enter the service mode again.. Press the buttons on the remote commander in order of [8], [7], [], [ENTER], and the diop value is displayed.. Confirm value is the following specification value, and turn the power off. Specification value: BD : 6 ma DVD/CD : 9 ma. Turn the power on, confirm playback performance of the BD (BLX-)/DVD (HLX-)/CD (HLX-A).. Completely assemble this unit, and complete the repair. 8

9 HBD-E/E/E/E/E6 Ver.. NOTE OF REPLACING MB OR WLAN/ BT COMBO CARD When the MB board or WLAN/BT COMBO card are replaced, please execute the below service mode.. Please update FW to M6.R.7. Whenever replace MB board or WLAN/BT COMBO CARD please execute Reset to Factory Default Settings from XMB. Procedure: [Home menu Setup Resetting Reset to Factory Default Settings All Settings] Next, go to service menu and execute () Bluetooth Enable and () Write Bluetooth device address to Registry. Finally check one touch NFC listening function at normal power on. Note: The operation in this mode must use a remote commander and TV monitor.. Connect this unit with TV monitor.. Press the (\/) button to turn the power on.. Press button in order of the [DISPLAY] [] [] [] [SUBTITLE] on the remote commander. (Make the interval when each button is pressed within two seconds). Enter the BD service mode. The OSD menu on TV monitor can be operated by remote commander.. Press [m] and Enter Diag. 6. Press [,] and Enter Bluetooth Device Test (Screen ). 7. Enter () Bluetooth Enable, wait until the display show Status : Bluetooth Enable Successful (Screen ). 8. Enter () Write Bluetooth device address to Registry, wait until the display show Bluetooth Device Address and Status : Write Successfull (Screen ). 9. Enter [RETURN] to the selection of test category. NOTE THE BD DRIVE (BPX-7) PARTS REPLACING The mechanism blocks except optical device of BD drive (BPX-7) are chiefly composed of the following parts. HOLDER, CHUCK ASSY LOADING ASSY COVER, DRIVE These parts are produced by two venders, it is not compatible. Therefore, HOLDER, CHUCK ASSY and LOADING ASSY are supplied by one pair as repair parts. Please exchange both HOLDER, CHUCK ASSY and LOADING ASSY at the same time. COVER, DRIVE need not be exchanged at the same time. Note : The laser caution label is not pasted to LOADING FOR SER- VICE. Please peel off an original laser caution label, and paste it to LOADING FOR SERVICE when you use LOADING FOR SERVICE. LABEL, LASER CAUTION LOADING FOR SERVICE HOLDER, CHUCK ASSY LOADING ASSY (Screen ) Diag Category: Bluetooth Device Test Diag Category: Bluetooth Device Test [] Bluetooth Enable [] Bluetooth Disable [] Write Bluetooth device address to Registry [] Bluetooth Inquiry Test COVER, DRIVE Note : If laser caution label is a condition of the figure below, it is acceptable. Status : Bluetooth Enable Successful! (Screen ) HELP: [UP][DOWN][ENT][RET] (Screen ) Diag Category: Bluetooth Device Test [] Bluetooth Enable [] Bluetooth Disable [] Write Bluetooth device address to Registry [] Bluetooth Inquiry Test Bluetooth device address : ::6::FD:CF Status : Write Successful! HELP: [UP][DOWN][ENT][RET] 9

10 HBD-E/E/E/E/E6 Ver.. MODEL IDENTIFICATION - Rear view - Part No. Model Part No. E [] E [] E [] E [] E [] NOTE OF REPLACING THE IC AND IC ON THE AMP AND THE COMPLETE AMP When IC and IC on the AMP board and the complete AMP board are replaced, it is necessary to spread the compound (GREASE (G-77)) KG) (Part No ) between parts and heat sink. Spread the compound referring to the figure below. AMP Board (Component Side) CAPACITOR ELECTRICAL DISCHARGE PROCESSING When checking the board, the electrical discharge is necessary for the electric shock prevention. Connect the resistor to both ends of respective capacitors. Switching regulator C7, C, C, C, C IC IC SWITCHING REGULATOR (Conductor Side) C C C C C7 IC IC (To both ends of each capacitor) 8 / W

11 HBD-E/E/E/E/E6 Ver.. CHECKING METHOD OF NETWORK OPERATION It is necessary to check the network operation, when replacing the MB board. Check the operation of wireless and wired LAN, according to the following method.. Checking Method of Wireless LAN Operation Check that access point is recognized surely. Necessary Equipment: Wireless access point with router function (AP) Procedure:. Press the [HOME] button on the remote commander to enter the home menu.. Press the [m]/[m]/[<]/[,] buttons on the remote commander to select Network Settings Internet Settings, and press the [ ] button on the remote commander.. Press the [m]/[m] buttons on the remote commander to select Wireless Setup (built-in), and press the [ ] button on the remote commander.. The system starts searching for access points, and displays a list of up available network name (SSID).. Check that access point (SSID) is displayed on the searching result. Note: Refer to the instruction manual about details of the setting method.. Checking method of wired LAN operation Check that access point is recognized surely. Procedure:. Connect the main unit to the router or the hub, etc. with the LAN cable.. Press the [HOME] button on the remote commander to enter the home menu.. Press the [m]/[m]/[<]/[,] buttons on the remote commander to select Network Settings Internet Settings, and press the [ ] button on the remote commander.. Press the [m]/[m] buttons on the remote commander to select Wired Setup, and press the [ ] button on the remote commander.. Press the [m]/[m] buttons on the remote commander to select Auto, and press the [ ] button on the remote commander. 6. Press the [,] button on the remote commander. 7. Press the [m]/[m] buttons on the remote commander to select Save & Connect, and press the [ ] button on the remote commander. 8. When Internet Settings is now complete. appears, then press the [ ] button on the remote commander. 9. Press the [HOME] button on the remote commander to enter the home menu.. Press the [m]/[m]/[<]/[,] buttons on the remote commander to select Network Settings Network Connection Diagnostics, and press the [ ] button on the remote commander.. Press the [<]/[,] buttons on the remote commander to select IPV or IPV6, and press [ ] button on the remote commander.. Press the [<]/[,] buttons on the remote commander to select Start, and press the [ ] button on the remote commander.. Check that IP address can be acquired. Note: Refer to the instruction manual about details of the setting method.

12 HBD-E/E/E/E/E6 Ver..7 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF Note : After the case is removed, this work is done. Note : Please prepare the thin wire (clip etc. processed to the length of 8 cm or more). Remove the case. (Illustration of disassembly is omitted.) hole Side view Insert the clip etc. processed to the length of 8 cm or more in the hole on the side of the chassis and push. BD drive tray Insert the clip etc. 8 cm or more tray Note: Push after it inserts it in this hole well. Top view SERVICE POSITION MB board BD drive (BPX-7) AMP board POWER KEY board switching regulator (SWR) (L9W-) (US, CND, AEP, UK, SAF, SP, TW, AUS, TH, CH) (L9W) (E, E, PX, EA, E, E, RU, MX6, AR) RC-S8/A (WW) card, WLAN/BT COMBO PANEL board NON-KARAOKE board (EXCEPT SP, RU) KARAOKE board (SP, RU) Abbreviation AR : Argentina model AUS : Australian model CH : Chinese model CND : Canadian model E : V AC area in E model E : V AC area in E model E : V AC area in E model E : Chilean and Peruvian models EA : Saudi Arabia model MX6 : Latin-American model PX : PX model RU : Russian model SAF : South African model SP : Singapore model TH : Thai model TW : Taiwan model

13 This set can be disassembled in the order shown below. -. DISASSEMBLY FLOW HBD-E/E/E/E/E6 SECTION Ver.. DISASSEMBLY SET -. HOW TO BEND FFC (Page ) -. CASE (Page ) -. PANEL LOADING ASSY (Page ) -. FRONT PANEL ASSY (Page 6) -6. BD DRIVE (BPX-7) (Page 6) -7. POWER KEY, WLAN/BT COMBO CARD, KARAOKE (SP, RU), PANEL (Page 7) -8. MB (Page 8) -9. AMP (Page 8) -. SWITCHING REGULATOR (SWR) (Page 9) -. OPTICAL PICK-UP BLOCK (KEM8AAA), WIRE (FLAT TYPE) (Page )

14 HBD-E/E/E/E/E6 Ver.. -. HOW TO BEND FFC : Mountain fold : Valley fold wire (flat type) (8 core), length 6 mm (Ref. No. ) RC-S8/A (WW) The upper side is contact side. mm mm º MB (CN86) The upper side is contact side. wire (flat type) ( core), length mm (Ref. No. 7) (EXCEPT SP, RU) MB board (CN8) The upper side is contact side. mm mm º º 8 mm mm PANEL board (CN) The upper side is contact side. wire (flat type) ( core), length mm (Ref. No. 7) (SP, RU) MB board (CN8) The upper side is contact side. mm º º wire (flat type) ( core), length mm (Ref. No. ) mm mm mm mm PANEL board (CN) The upper side is contact side. MB board (CN77) The upper side is contact side. AMP board (CN) The upper side is contact side. wire (flat type) (9 core), length mm (Ref. No. 6) 9 mm 78 mm mm mm mm MB board (CN66) The lower side is contact side. º º º 9 mm mm 97 mm mm BD drive (BPX-7) The lower side is contact side. flexible flat cable ( core), length mm (Ref. No. 7) 6 mm 9 mm 9 mm mm 6 mm MB board (CN) º º BD drive (BPX-7) The upper side is contact side. mm 9 mm The upper side is contact side. wire (flat type) ( core), length 76 mm (Ref. No. 8) MB board (CN67) The lower side is contact side. mm 6 mm 9 mm º º º 8 mm mm 8 mm 9 mm mm BD drive (BPX-7) The lower side is contact side.

15 HBD-E/E/E/E/E6 Ver.. Note: Follow the disassembly procedure in the numerical order given. -. CASE four screws (+BV (-CR)) 6 7 case five claws A four screws (+BV (-CR)) A -. PANEL LOADING ASSY panel loading assy hole Side view Insert the clip etc. processed to the length of 8 cm or more in the hole on the side of the chassis and push. BD drive four claws Insert the clip etc. 8 cm or more tray Note: Push after it inserts it in this hole well. Top view

16 HBD-E/E/E/E/E6 Ver.. -. FRONT PANEL ASSY Abbreviation RU : Russian model SP : Singapore model :LUH VHWWLQJ switching regulator (SWR) MB board front side wire (flat type) (8 core) (CN86) (E) (E/E/E6) three claws three claws front panel assy four claws four claws 6 8 (SP) -6. front panel assy BD DRIVE (BPX-7) wire (flat type) ( core) (CN67) 7 sheet, sound wire (flat type) (9 core) (CN66) four screws (+BV (-CR)) flexible flat cable ( core) (CN) 8 BD drive BPX-7 boss Note: When you install the BD drive (BPX-7), please match the position of the boss two places. 6 6

17 HBD-E/E/E/E/E6 Ver POWER KEY, WLAN/BT COMBO CARD, KARAOKE (SP, RU), PANEL switching regulator (SWR) front side front side MB board harness USB MB board switching regulator (SWR) CN8 (P) 7 wire (flat type) ( core) (CN) (SP, RU) wire (flat type) ( core) (CN) (EXCEPT SP, RU) CN (P) POWER KEY board one screw (+BV (-CR)) one screw (+BV (-CR)) 6 card, WLAN/BT COMBO D F G E 9 harness (USB) CN (P) switching regulator (SWR) (SP, RU) D F E 8 CN (6P) front side two screws (+BV (-CR)) qs one screw (+BV (-CR)) qa PANEL board G qd KARAOKE board (EXCEPT SP, RU) D MB board F E qa PANEL board Abbreviation RU : Russian model SP : Singapore model Note: When replacing the WLAN/BT COMBO card, refer to CHECKING METHOD OF NETWORK OPERATION (page ). two screws (+BV (-CR)) qf NON-KARAOKE board 7

18 HBD-E/E/E/E/E6 Ver MB five screws (+BV (-CR)) 8 MB board 6 one screw (+BV (-CR)) 7 one screw (+B ) CN (P) wire (flat type) ( core) (CN77) tape CN (8P) -9. AMP switching regulator (SWR) AMP board rear side three screws (+BV (-CR)) four screws (+BV (-CR)) heat sink (AMP.CH) CN (P) CN (P) 7 AMP board 6 two screws (+BV (-CR)) 8

19 HBD-E/E/E/E/E6 Ver SWITCHING REGULATOR (SWR) five screws (+BV (-CR)) switching regulator (SWR) (L9W-) (US, CND, AEP, UK, SAF, SP, TW, AUS, TH, CH) (L9W) (E, E, PX, EA, E, E, RU, MX6, AR) four claws insulation, bottom CN (P) rear side switching regulator (SWR) Abbreviation AR : Argentina model AUS : Australian model CH : Chinese model CND : Canadian model E : V AC area in E model E : V AC area in E model E : V AC area in E model E : Chilean and Peruvian models EA : Saudi Arabia model MX6 : Latin-American model PX : PX model RU : Russian model SAF : South African model SP : Singapore model TH : Thai model TW : Taiwan model 9

20 HBD-E/E/E/E/E6 Ver.. -. OPTICAL PICK-UP BLOCK (KEM8AAA), WIRE (FLAT TYPE) four claws holder, chuck assy (T) two claws 6 two screws (S), float insulator qa device, optical KEM8AAA qs tape, non-halogene qf tape, FFC insulator 9 insulator qd wire (flat type) ( core) qg flexible flat cable ( core) 7 8 Insert the thin wire (clip etc.). qk cover, drive qj qh wire (flat type) (9 core) loading assy (T) Bottom view Note: This illustration sees the loading assy (T) from bottom side. wire (flat type) (9 core) Through the hole flexible flat cable ( core) Fold Through the hole tape, FFC 9 cover, drive 7 tape, non-halogene terminal face Fold terminal face 8 6 wire (flat type) ( core) loading assy (T) Under the guide Under the guide (Fold area)

21 HBD-E/E/E/E/E6 SECTION Ver.. TEST MODE COLD RESET The cold reset clears certain data in this system without initialize Personal Information and some BD operation data. Execute this mode when returning the unit to the customers. Procedure:. Press the [?/] button to turn the power on.. Press the [x] and [VOL ] buttons simultaneously and hold down (around seconds).. The message WAIT appears then RESET appears on fluorescent indicator tube, then becomes standby states. DEMO MODE This mode let you lock the disc tray. When this mode is activated, the disc will not eject when the [Z] button is pressed. The message D. LOCK will be displayed on the fluorescent indicator tube. Procedure:. Press the [?/] button to turn the power on.. Press the [FUNCTION] button to select the BD/DVD.. Insert a disc.. During stop condition, press the [x] and [Z] buttons simultaneously and hold down (around seconds) until D. LOCK displayed on the fluorescent indicator tube. Releasing method: Press the [x] and [Z] buttons simultaneously and hold down (around seconds) until D. OFF displayed on the fluorescent indicator tube. PANEL TEST Procedure:. Press the [?/] button to turn the power on.. Press button in order of the [DISPLAY] [] [] [] [SUBTITLE] on the remote commander (Make the interval when each button is pressed within two seconds).. All segments in fluorescent indicator tube are lighted up. And half segments in fluorescent indicator tube are lighted up, others half segments in fluorescent indicator tube are lighted up, then all segments in fluorescent indicator tube are lighted up. This operation is repeated.. In the state of step, press the [VOL +] button on the remote commander and model information is displayed on the fluorescent indicator tube. Each time the [VOL +] button on the remote commander is pressed, the display changes from destination information, STR version, special mode in this order, and returns to the model information display.. In the state of step, press the [FUNCTION] button on the remote commander and K is displayed on the fluorescent indicator tube. K value increases whenever a button or sensor on the unit is pressed. However, once a button or sensor has been pressed, it is no longed taken into account. All button and sensors on the unit are pressed, OK and K 9 are alternately displayed on the fluorescent indicator tube. Releasing method: To release from this mode, press the [?/] button. FACTORY INITIALIZE Return all of the unit setting to their factory defaults. Note : Disconnect the following connections when you use this mode. USB LAN Note : The operation in this mode must use a remote commander and TV monitor. Procedure:. Press the [?/] button to turn the power on.. Press the [HOME] button on the remote commander, and the home menu is displayed.. Select Setup Resetting, and press the [ ] button on the remote commander. Easy Network Settings Resetting. Select Initialize Personal Information, and press the [ ] button on the remote commander.. Select OK, and press the [ ] button on the remote commander. Initialize Personal Information OK Reset to Factory Default Settings Initialize Personal Information Delete personal data when disposing The information below will be deleted. Do you want to proceed? - Playback history - Internet video utilization information Cancel

22 HBD-E/E/E/E/E6 Ver.. 6. The message Close appears, and press the [ ] button on the remote commander. Initialize Personal Information Initialization complete. Close 7. Select Reset to Factory Default Settings, and press the [ ] button on the remote commander. Reset to Factory Default Settings Restore each setting to the factory d Initialize Personal Information 8. Select All Settings, and press the [ ] button on the remote commander. BD SERVICE MODE Note: The operation in this mode must use a remote commander and TV monitor. Setting method of the BD service mode:. Connect this unit with TV monitor.. Press the [?/] button to turn the power on.. Press button in order of the [DISPLAY] [] [] [] [SUBTITLE] on the remote commander. (Make the interval when each button is pressed within two seconds). Enter the BD service mode. The OSD menu on TV monitor can be operated by remote commander.. Main Functions Diag Performs unit test of devices installed on the board. Log Error log is displayed. Displayed contents can also be saved in an USB memory device. Factory Initialize Restores the unit to its factory settings. Network Checks the wired network connection. Version Up System Information Displays the system information of the unit. Displays information such as the software version, drive information, etc. EMC Test Mode Not used. Drive Write drive OP data and check drive. HDD Mode Not used. Reset to Factory Default Settings Screen Settings Audio Settings BD/DVD Viewing Settings Parental Control Settings System Settings Network Settings All Settings 9. Select Start, and press the [ ] button on the remote commander. All Settings Restore all settings to the factory default settings. The system will turn off after reset. Start Cancel. Initialization ends when the message HELLO on the fluorescent indicator tube disappears.

23 HBD-E/E/E/E/E6 Ver... Menu Tree Service ode enu [] [] Dia [] [] Lo [] [] Factory Initialize [] [] Network [] [] Version Up [6] [6] System Information [7] [8] Drive Dia Device Test Video Test Video output test udio Test udio output test udio Input Test Only wireless model used Not used Not used Transcorder Test Not used Lo Displays Error Error Lo Displays error lo Not used Factory Initialize Start Initialize Network twork di View network status Version Up DISC update Start Update System Information Displays system information Not used Drive Write drive OP data and check drive Not used

24 HBD-E/E/E/E/E6 Ver... Service Mode Menu (Top Menu) This is the top menu of service mode. Each function is accessed from this screen. Operation: [] Moves to Diag screen [] Moves to Log screen [] Moves to Factory Initialize screen [] Moves to Network screen [] Moves to Version Up (DISC version update) screen [6] Moves to System Information screen [7] Moves to EMC test mode screen (Not used) [8] Moves to Drive screen [9] Moves to HDD mode (Not used) [M]/[m] Moves the cursor [ ] Moves to the screen of the item selected with the cursor (Screen ) Diag Category: Device Test Diag Category: Device Test Device: USB Host Front USB Media check... OK Checking... * Cursor is not displayed when the menu is first displayed. (Screen ) HELP: [RIGHT] [UP] [ENT] [RET] Service Mode Menu [] Diag [] Log [] Factory Initialize [] Network [] Version Up [6] System Information [7] EMC Test Mode [8] Drive [9] HDD mode HELP : [UP] [DOWN] [ENT] [NUM] HELP (currently available keys, etc.) is displayed. Diag (Device Test) This screen is used to test devices mounted on the board. Screen : Selects the test category Operation: [<]/[,] Selects the category [m]/[ ] Moves to the selected category [RETURN] Returns to the service top menu Screen : Device test Selects the device to test after selecting Device Test in screen. Operation: [<]/[,] Selects the device to test [ ] Executes the test [M] Returns to selection of test category [RETURN] Returns to selection of test category List of test categories Device Test Video Test Audio Test Audio Input Test Wireless LAN Test Mic Test (Not used) HDMI Input Test (Not used) Transcorder Test (Not used) Bluetooth Device Test Device Test: List of devices USB Host : USB media check (front). Only one time.. Diag (Video/Audio Test) This screen performs video and audio tests. Screen : When video test category is selected Operation: [ ] Shows Color Bar [M]/[RETURN] Returns to the selection of test category Screen : When audio test category is selected Operation: [ ] Generate TONE Sound [M]/[RETURN] Returns to the selection of test category Video test: Outputs a color bar (HDMI). Audio test: TONE sound output (speaker & HDMI). (Screen ) (Screen ) Diag Category: Video Test Diag Category: Audio Test HELP: [UP][ENT][RET] HELP: [UP] [ENT] [RET] [ENT] Show Color Bar [ENT] Generate TONE Sound

25 HBD-E/E/E/E/E6 Ver.. 6. Diag (Audio Input Test) This screen performs audio input test. Screen : Select Audio Input Test Category Operation: [<]/[,] Selects the category [m]/[ ] Activate the selected category [RETURN] Returns to the service top menu Screen : Select Input Device After Audio Input Test selects in Screen, the device to test is chosen. Operation: [M]/[m] Selects Device [ ] Activate and Start Test/Stop [RETURN] Returns to the selection of test category Device Test : Device List Digital Input : CXD99R-BA is inputted from Optical Digital Input : CXD99R-BA is inputted from ARC Analog Input : CXD99R-BA is inputted from AUDIO Audio Input Test CXD99R-BA is inputted from DIR/analog and outputs LineOut (8ch) L and R. Check tone sound by speaker connected with LineOut (8ch) L and R. (Input; LPCM 8kHz ch) Diag Category: Diag Audio Input Test Category: Audio Input Test Device: Digital Input Digital Input Analog Input 7. Diag (Wireless LAN Test) This screen performs wireless LAN test. Screen : Selects the Wireless LAN test category Operation: [<]/[,] Selects the category [m]/[ ] Moves to the selected category [RETURN] Returns to the service top menu Screen : Wireless LAN test [] Show WLAN Hwinfo [] Connect to AccessPoint [] Start display RSSI value. [] Start Ping Test Operation: [M]/[m] Selects the test [ ] Executes the test [RETURN] Returns to selection of test category Screen : Select [] Show WLAN HwInfo Viewing the display Serial : Serial Number Hard : Hardware Version Mac : Mac Address Screen : Select [] Connect to AccessPoint Connect Access Point only with the following AP settings. CERT: NO-ENCRYPT WEPKEY: abcdef PMK: ABCDE SSID: SONY-Test-R IPADDR: NETMASK:... BROADCAST: When connect to AP, Status is Connected! When cannot connect to AP, Status is can t Connect! Screen : Select [] Start Display RSSI Value Display RSSI value. (Screen ) [ENT] Start Input Sound Screen : Select [ ] Start Ping Test Ping Test. IP address use the value of (Screen ) HELP: [LEFT] [RIGHT] [UP] [DOWN] [ENT] [RET] [ ] [ ] Diag Category: Audio Input Test Device: Digital Input Digital Input Analog Input [ENT] Stop Input Sound HELP: [LEFT] [RIGHT] [UP] [DOWN] [ENT] [RET]