SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z KIMBALL ELECTRONIC LABORATORY, INC W 21st Lane Hialeah, FL Javier Balceiro Phone: CALIBRATION Valid To: June 30, 2020 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Dimensional Parameter/Equipment Range CMC 2, 3 (±) Comments Calipers Up to 24 in ( L) in Gage blocks Gage Blocks Up to 4 in ( L) in Tesa UPC comparator with gage blocks Micrometers Up to 12 in ( L) in Gage blocks Plug Gages Up to 4 in 48 in ULM-600C II. Electrical DC/ Low Frequency Parameter/Equipment Range CMC 2, 4 (±) Comments DC Voltage Generate (0 to ) mv (0.33 to 3.299) V (3.3 to ) V (33 to ) V (330 to 1000) V 60 V/V + 3 V 50 V/V + 5 V 50 V/V + 50 V 55 V/V V 55 V/V mv (A2LA Cert. No ) 05/21/2018 Page 1 of 10

2 Parameter/Equipment Range CMC 2, 4, 5 (±) Comments DC Voltage Measure Up to 100 mv (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V 13 V/V V 14 V/V V 14 V/V V 14 V/V + 31 V 14 V/V + 90 V HP 3458A DC Current Generate (0.3 to 3.29) ma (3.3 to 32.9) ma (33 to 329.9) ma 330 ma to 1 A (1 to 10) A % A % A % A % + 43 A % A DC Current Measure 100 A to 1 ma (1 to 10) ma (10 to 100) ma 100 ma to 1 A 18 A/A A 18 A/A A 28 A/A A % + 44 A HP 3458A Resistance Generate (0 to 11) (11 to 33) (33 to 110) (110 to 330) (330 to 1100) (1.1 to 3.3) k (3.3 to 11) k (11 to 33) k (33 to 110) k (110 to 330) k (330 to 1100) k (1.1 to 3.3) M (3.3 to 11) M (11 to 33) M (33 to 110) M (110 to 330) M % + 8 m % + 15 m % + 15 m % + 15 m % + 56 m % + 60 m % m % m % % % % % % % k 0.51 % + 17 k (A2LA Cert. No ) 05/21/2018 Page 2 of 10

3 Parameter/Equipment Range CMC 2, 5 (±) Comments Resistance Measure (0 to 10) (10 to 100) (0.1 to 1) k (1 to 10) k (10 to 100) k (0.1 to 1) M (1 to 10) M (10 to 100) M 10 / m 11 / m 14 / m 18 / m 18 / + 93 m 23 / / % HP 3458A Parameter/Range Frequency CMC 2, 4 (±) Comments AC Voltage Generate (1 to 33) mv (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (100 to 500) khz 0.35 % + 20 V 0.15 % + 20 V 0.21 % + 20 V 0.25 % + 20 V 0.35 % + 33 V 1.0 % + 60 V (33 to 330) mv (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz (100 to 500) khz 0.25 % + 50 V 0.05 % + 21 V 0.10 % + 20 V 0.16 % + 40 V 0.24 % V 0.70 % V 330 mv to 3.3 V (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz 0.15 % V 0.03 % + 60 V 0.08 % + 60 V 0.14 % V 0.24 % V (3.3 to 33) V (10 to 45) Hz 45 Hz to 10 khz (10 to 20) khz 0.15 % V 0.04 % V 0.08 % mv 0.19 % + 5 mv 0.24 % + 17 mv (33 to 330) V (1 to 10) khz (10 to 20) khz 0.05 % mv 0.08 % + 15 mv 0.09 % + 33 mv (A2LA Cert. No ) 05/21/2018 Page 3 of 10

4 Parameter/Range Frequency CMC 2, 4, 5 (±) Comments AC Voltage Generate (cont) (330 to 1000) V (5 to 10) khz 0.05 % + 81 mv 0.21 % mv 0.21 % mv AC Voltage Measure (1 to 10) mv (1 to 40) Hz (1 to 20) khz (100 to 300) khz % V % V % V % V % + 11 V 3.3 % + 75 V HP 3458A (10 to 100) mv (1 to 40) Hz (1 to 20) khz (100 to 300) khz % V % V % V % V % V 0.27 % + 50 V 100 mv to 1 V (1 to 40) Hz (1 to 20) khz (100 to 300) khz % + 39 V % + 21 V % + 21 V % + 32 V % + 25 V 0.31 % mv (1 to 10) V (1 to 40) Hz (1 to 20) khz % mv % mv % mv % mv % mv (10 to 100) V (1 to 20) khz % mv % mv % mv 0.13 % mv (100 to 700) V % + 20 mv (A2LA Cert. No ) 05/21/2018 Page 4 of 10

5 Parameter/Range Frequency CMC 2, 4 (±) Comments AC Current Generate (30 to 330) A (5 to 10) khz 0.25 % A 0.13 % A 0.13 % A 0.40 % A 1.3 % A (0.33 to 3.3) ma (5 to 10) khz 0.20 % A 0.10 % A 0.10 % A 0.20 % A 0.60 % A (3.3 to 33) ma (5 to 10) khz 0.20 % + 3 A 0.10 % + 3 A 0.09 % + 3 A 0.20 % + 3 A 0.60 % + 3 A (33 to 330) ma 0.20 % + 30 A 0.10 % + 30 A 0.09 % + 30 A 0.20 % + 30 A (0.33 to 1) A (10 to 45) Hz 0.22 % ma 0.13 % ma 0.81 % ma (1 to 10) A (45 to 65) Hz (65 to 500) Hz 500 Hz to 1 khz 0.07 % ma 0.10 % ma 0.33 % ma (A2LA Cert. No ) 05/21/2018 Page 5 of 10

6 Parameter/Range Frequency CMC 2, 5 (±) Comments AC Current Measure Up to 100 A (45 to 100) Hz 100 Hz to 5 khz 0.40 % A 0.15 % A 0.06 % A 0.06 % A HP 3458A 100 A to 1 ma (45 to 100) Hz 100 Hz to 5 khz 0.41 % A 0.15 % A 0.06 % A 0.03 % A (1 to 10) ma (45 to 100) Hz 100 Hz to 5 khz 0.40 % + 2 A 0.15 % + 2 A 0.06 % + 2 A 0.03 % + 2 A (10 to 100) ma (45 to 100) Hz 100 Hz to 5 khz 0.40 % + 20 A 0.15 % + 20 A 0.06 % + 20 A 0.03 % + 20 A 100 ma to 1A (45 to 100) Hz 100 Hz to 5 khz 0.40 % A 0.16 % A 0.08 % A 0.10 % A Parameter/Equipment Range CMC 2, 4 (±) Comments Capacitance Generate (0.5 to 1.1) nf (1.1 to 3.3) nf (3.3 to 11) nf (11 to 33) nf (33 to 110) nf (110 to 330) nf (0.33 to 1.1) F (1.1 to 3.3) F (3.3 to 11) F (11 to 33) F (33 to 110) F (110 to 330) F 330 F to 1.1 mf 0.45 % + 11 pf 0.51 % + 10 pf 0.50 % + 11 pf 0.26 % pf 0.26 % pf 0.26 % pf 0.23 % nf 0.36 % + 3 nf 0.36 % nf 0.41 % + 30 nf 0.79 % + 13 nf 0.67 % nf 1.0 % nf (A2LA Cert. No ) 05/21/2018 Page 6 of 10

7 Parameter/Equipment Range CMC 2, 4 (±) Comments Electrical Calibration of Thermocouple Indicating Equipment Type B (600 to 800) o C (800 to 1000) o C (1000 to 1550) o C (1550 to 1820) o C 0.47 o C 0.43 o C 0.33 o C 0.36 o C Type C (0 to 150) o C (150 to 650) o C (650 to 1000) o C (1000 to 1800) o C (1800 to 2316) o C 0.32 o C 0.30 o C 0.34 o C 0.52 o C 0.86 o C Type E (-250 to -100) o C (-100 to -25) o C (-25 to 350) o C (350 to 650) o C (650 to 1000) o C 0.53 o C 0.19 o C 0.18 o C 0.20 o C 0.26 o C Type J (-210 to -100) o C (-100 to -30) o C (-30 to 150) o C (150 to 760) o C 0.29 o C 0.19 o C 0.17 o C 0.20 o C Type K (-200 to -100) o C (-100 to -25) o C (-25 to 120) o C (120 to 1000) o C (1000 to 1372) o C 0.34 o C 0.21 o C 0.19 o C 0.28 o C 0.41 o C (A2LA Cert. No ) 05/21/2018 Page 7 of 10

8 Parameter/Equipment Range CMC 2, 4 (±) Comments Electrical Calibration of Thermocouple Indicating Equipment (cont) Type N (-200 to -100) o C (-100 to -25) o C (-25 to 120) o C (120 to 410) o C (410 to 1300) o C 0.41 o C 0.24 o C 0.22 o C 0.21 o C 0.29 o C Type R (0 to 250) o C (250 to 400) o C (400 to 1000) o C (1000 to 1767) o C 0.58 o C 0.36 o C 0.35 o C 0.41 o C Type S (0 to 250) o C (250 to 1000) o C (1000 to 1400) o C (1400 to 1767) o C 0.48 o C 0.37 o C 0.38 o C 0.47 o C Type T (-250 to -150) o C (-150 to 0) o C (0 to 120) o C (120 to 400) o C 0.64 o C 0.26 o C 0.19 o C 0.17 o C III. Electrical RF/Microwave Parameter/Range Frequency CMC 2, 6 (±) Comments Amplitude Modulation Measure Rate: 50 Hz to 10 khz Depths: 5 % to 99 % 150 khz to 10 MHz 2.0 % % rng HP 8902A with 11722A Rate: 20 Hz to 10 khz Depths: 5 % to 99 % 150 khz to 10 MHz 3.0 % % rng Rate: 50 Hz to 50 khz Depths: 5 % to 99 % (10 to 1300) MHz 1.0 % % rng Rate: 20 Hz to 100 khz Depths: 5 % to 99 % (10 to 1300) MHz 3.0 % % rng (A2LA Cert. No ) 05/21/2018 Page 8 of 10

9 Parameter/Range Frequency CMC 2, 6 (±) Comments Frequency Modulation Measure Rate: 20 Hz to 10 khz Dev: 40 khz Peak 250 khz to 10 MHz 2.0 % % rng HP 8902A with 11722A Rate: 50 Hz to 100 khz Dev: 400 khz Peak (10 to 1300) MHz 0.97 % % rng Rate: 20 Hz to 200 khz Dev: 400 khz Peak (10 to 1300) MHz 5.0 % % rng Distortion Measure 20 Hz to 20 khz (20 to 100) khz 2.3 db 3.0 db HP 8903B IV. Mechanical Parameter/Equipment Range CMC 2, 6 (±) Comments Pressure (Gauges, Transducers, Air Data Test Sets, Pitot Testers) (0.5 to 32) in Hg (32 to 68) in Hg (0 to 20) psig (20 to 50) psig (50 to 100) psig (100 to 1000) psig (1000 to 2500) psig (2500 to 5000) psig in Hg in Hg psig psig psig 1.3 psig 3.4 psig 6.7 psig Ruska 2468A Eaton UPS 3000 (5000 to 7500) psig 4.4 psig Heise HQS (1000 to 6000) psig (3000 to ) psig % of value psig % of value Fluke PPCH-G Torque Measuring Equipment (0 to 2000) ft lbf 1.0 % full scale AKO TSD This laboratory offers commercial calibration service. (A2LA Cert. No ) 05/21/2018 Page 9 of 10

10 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. Where ranges are not specified, the best measurement uncertainty stated is for the cardinal points only. 3 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches. 4 The measurands stated are generated with the. This capability is suitable for the calibration of the devices intended to measure the stated measurand in the ranges indicated. CMC is read as output plus one-year floor specifications where defined. CMCs are expressed as either a specific value that covers the full range or as a combination of the percent or portion of the reading plus a fixed floor specification. 5 The measurands stated are measured with the HP 3458A. This capability is suitable for the calibration of the devices intended to generate the measurand in the ranges indicated. CMCs are expressed as either a specific value that covers the full range or as a combination of the fraction of the reading/output plus a range specification. 6 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification. (A2LA Cert. No ) 05/21/2018 Page 10 of 10

11 Accredited Laboratory A2LA has accredited KIMBALL ELECTRONIC LABORATORY, INC. Hialeah, FL for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSL Z and R205 Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017). Presented this 21 st day of May President and CEO For the Accreditation Council Certificate Number Valid to June 30, 2020 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.