LM101A, LM201A, LM301A HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
|
|
- Marcus Camron Kelly
- 6 years ago
- Views:
Transcription
1 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS D9, OCTOBER 979 REVISED SEPTEMBER 990 Low Input Currents Low Input Offset Parameters Frequency and Transient Response Characteristics Adjustable Short-Circuit Protection Offset-Voltage Null Capability No Latch-Up Wide Common-Mode and Differential Voltage Ranges Same Pin Assignments as ua709 Designed to be Interchangeable with National Semiconductor and description symbol The, LM20A, and are highperformance operational amplifiers featuring very low input bias current and input offset voltage and current to improve the accuracy of highimpedance circuits using these devices. The high common-mode input voltage range and the absence of latch-up make these amplifiers ideal for voltage-follower applications. The devices are protected to withstand short circuits at the output. The external compensation of these amplifiers allows the changing of the frequency response (when the closed-loop gain is greater then unity) for applications requiring wider bandwidth or higher slew rate. A potentiometer may be connected between the offset-null inputs (N and N2), as shown in Figure 7, to null out the offset voltage. The is characterized for operation over the full military temperature range of 55 C to 25 C, the LM20A is characterized for operation from 25 C to 5 C, and the is characterized for operation from 0 C to 70 C. Noninverting Input IN+ Inverting Input IN + N2 N/ Output N/ IN IN+ V CC N/ IN IN+ V CC N/ IN IN+ V CC D, JG, OR P PACKAGE (T0P VIEW) W FLAT PACKAGE (T0P VIEW) U FLAT PACKAGE (T0P VIEW) V CC+ OUT OFFSET N2 V CC+ OUT OFFSET N2 V CC+ OUT OFFSET N2 FK CHIP-CARRIER PACKAGE (T0P VIEW) IN IN+ N/ CC V N2 No internal connection V CC+ OUT PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 99, Texas Instruments Incorporated POST OFFICE BOX 550 DALLAS, TEXAS
2 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS PACKAGE TA VIO MAX SMALL OUTLINE CHIP CARRIER CERAMIC DIP PLASTIC DIP FLAT at 25 C PACK FLAT PACK (D) (FK) (JG) (P) (U) (W) 0 C to 70 C 7.5 mv D P PACKAGE AVAILABLE OPTIONS 25 C to 5 C 2 mv LM20AD LM20AP 55 C to 25 C 2 mv D FK JG P U W The D package is available taped and reeled. Add the suffix R to the device type, (i.e., DR). absolute maximum ratings over operating free-air temperature range (unless otherwise noted) LM20A UNIT Supply voltage VCC+ (see Note ) V Supply voltage VCC (see Note ) V Differential input voltage (see Note 2) ±0 ±0 ±0 V Input voltage (either input, see Notes and ) ±5 ±5 ±5 V Voltage between either offset null terminal (N/N2) and VCC 0.5 to to to 2 V Duration of output short-circuit (see Note ) unlimited unlimited unlimited Continuous total power dissipation See Dissipation Rating Table Operating free-air temperature range 55 to25 25 to5 0to70 C Storage temperature range 5 to50 5 to50 5 to50 C Case temperature for 0 seconds: FK package 20 C Lead temperature, mm (/ inch) from case for 0 seconds JG, U, or W package 00 C Lead temperature, mm (/ inch) from case for 0 seconds D or P package C NOTES:. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC. 2. Differential voltages are at the noninverting input terminal with respect to the inverting input terminal.. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 5 V, whichever is less.. The output may be shorted to ground or either power supply. For the only, the unlimited duration of the short-circuit applies at (or above) 25 C case temperature or 75 C free-air temperature. For the LM20A only, the unlimited duration of the short-circuit applies at (or below) 5 C case temperatuare or 75 C free-air temperature. DISSIPATION RATING TABLE TA 25 C DERATING DERATE TA = 70 C TA = 5 C TA = 25 C POWER RATING FACTOR ABOVE TA POWER RATING POWER RATING POWER RATING D 500 mw 5. mw/ C C mw 77 mw 5 mw FK 500 mw.0 mw/ C 05 C 500 mw 500 mw 275 mw JG 500 mw. mw/ C 90 C 500 mw 500 mw 20 mw P 500 mw.0 mw/ C 7 C 500 mw 500 mw 200 mw U 500 mw 5. mw/ C 57 C 2 mw 5 mw 5 mw W 500 mw.0 mw/ C 7 C 500 mw 500 mw 200 mw recommended operating conditions MIN MAX UNIT Supply voltage, VCC+ 5 V Supply voltage, VCC POST OFFICE BOX 550 DALLAS, TEXAS 7525
3 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS electrical characteristics at specified free-air temperature, C C = 0 pf (see Note 5), LM20A PARAMETER TEST CONDITIONS UNIT MIN TYP MAX MIN TYP MAX 25 C VIO Input offset voltage VO = 0 mv Full range 0 Average temperature coefficient of αvio VO = 0 Full range 5 0 µv/ C input offset voltage 25 C IIO Input offset current na Full range TA = 55 C to 25 C Average temperature coefficient of TA = 25 C to MAX αiio na/ C input offset current TA = 0 C to 25 C TA = 25 C to 70 C C IIB Input bias current na Full range VICR Common-mode input voltage range See Note Full range ±5 ±2 V VCC± = ±5 V, 25 C Maximum peak-to-peak output RL = 0 kω Full range 2 2 VOPP V voltage swing VCC± = ±5 V, 25 C RL = 2 kω Full range VCC± = ±5 V, Large-signal differential voltage 25 C AVD VO = ±0 V, V/mV amplification RL 2 kω Full range 25 5 ri Input resistance 25 C MΩ 25 C CMRR Common-mode rejection ratio VIC = VICR min db Full range 0 70 Supply voltage rejection ratio 25 C ksvr db ( VCC/ VIO) Full range 0 70 No load, ICC Supply current VO = 0, 25 C.. ma See Note MAX All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Full range for is 55 C to 25 C, for LM20A is 25 C to 5 C, and for is 0 C to 70 C. NOTES: 5. Unless otherwise noted, VCC± = ±5 V to ±20 V for and LM20A, and VCC± = ±5 V to ±5 V for. All typical values are at VCC± = ±5 V.. For and LM20A, VCC± = ±20 V. For, VCC± = ±5 V. POST OFFICE BOX 550 DALLAS, TEXAS
4 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS TYPICAL CHARACTERISTICS INPUT OFFSET CURRENT FREE-AIR TEMPERATURE VCC ± = ±5 V 00 VCC ± = ±5 V INPUT BIAS CURRENT FREE-AIR TEMPERATURE IIO Input Offset Current na 2I LM20A Input Bias Current na IIB LM20A TA Free-Air Temperature C TA Free-Air Temperature C Figure Figure 2 V OPP Maximum Peak-to-Peak Output Voltage V MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (WITH SINGLE-POLE ENSATION) FREQUEY VCC ± = ±5 V RL = 0 KΩ TA = 25 C CC = 0 pf 0 k 0 k 00 k M 0 M f Frequency Hz CC = pf A VD Differential Voltage Amplification V/mV OPEN-LOOP LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION SUPPLY VOLTAGE RL = 2 KΩ TA = 25 C LM20A VCC± Supply Voltage V Figure Figure 2 POST OFFICE BOX 550 DALLAS, TEXAS 7525
5 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS TYPICAL CHARACTERISTICS A VD Differential Voltage Amplification OPEN-LOOP LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION FREQUEY VCC ± = ±5 V RL = 2 kω CC = 0 pf TA = 25 C Input and Output Voltages V VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE Output Input VCC ± = ±5 V RL = 2 kω CL = 00 pf CC = 0 pf TA = 25 C k 0 k 00 k f Frequency Hz M 0 M 00 M t Time µs Figure 5 Figure TYPICAL APPLICATION DATA R2 VCC+ V O V I R2 R R C C R 0 pf R R2 VI R + VO RL 2 kω R R R2 R R2 VCC N 5 MΩ N2 CC 5. MΩ Figure 7. Inverting Circuit with Adjustable Gain, Single-Pole Compensation, and Offset Adjustment POST OFFICE BOX 550 DALLAS, TEXAS
6 HIGH-PERFORMAE OPERATIONAL AMPLIFIERS 2 POST OFFICE BOX 550 DALLAS, TEXAS 7525
7 IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. TI warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage ( Critical Applications ). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI products in such applications requires the written approval of an appropriate TI officer. Questions concerning potential risk applications should be directed to TI through a local SC sales office. In order to minimize risks associated with the customer s applications, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does TI warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. Copyright 99, Texas Instruments Incorporated
8 This datasheet has been downloaded from: Datasheets for electronic components.
LM101A, LM201A, LM301A HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
HIGH-PERFORMAE OPERATIONAL AMPLIFIERS D9, OCTOBER 99 REVISED SEPTEMBER 99 Low Input Currents Low Input Offset Parameters Frequency and Transient Response Characteristics Adjustable Short-Circuit Protection
More informationua747c, ua747m DUAL GENERAL-PURPOSE OPERATIONAL AMPLIFIERS
No Frequency Compensation Required Low Power Consumption Short-Circuit Protection Offset-Voltage Null Capability Wide Common-Mode and Differential Voltage Ranges No Latch-Up Designed to Be Interchangeable
More informationLM148, LM248, LM348 QUADRUPLE OPERATIONAL AMPLIFIERS
µa741 Operating Characteristics Low Supply Current Drain...0.6 ma Typ (per amplifier) Low Input Offset Voltage Low Input Offset Current Class AB Output Stage Input/Output Overload Protection Designed to
More informationRC4136, RM4136, RV4136 QUAD GENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Continuous-Short-Circuit Protection Wide Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Unity Gain Bandwidth... MHz Typ Gain and Phase
More informationGENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Short-Circuit Protection Offset-Voltage Null Capability Large Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Designed to Be Interchangeable
More informationNE5532, NE5532A DUAL LOW-NOISE OPERATIONAL AMPLIFIERS
Equivalent Input Noise Voltage 5 nv/ Hz Typ at 1 khz Unity-Gain Bandwidth... 10 MHz Typ Common-Mode Rejection Ratio... 100 db Typ High dc Voltage Gain... 100 V/mV Typ Peak-to-Peak Output Voltage Swing
More informationRC4558, RC4558Y, RM4558, RV4558 DUAL GENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Continuous-Short-Circuit Protection Wide Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Unity Gain Bandwidth...3 MHz Typ Gain and Phase
More informationMC1458, MC1558 DUAL GENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Short-Circuit Protection Wide Common-Mode and Differential oltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Designed to Be Interchangeable With Motorola MC1/MC1 and Signetics
More informationTL070 JFET-INPUT OPERATIONAL AMPLIFIER
Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion.3% Typ Low Noise V n = 8 nv/ Hz Typ
More informationGENERAL-PURPOSE OPERATIONAL AMPLIFIERS
查询 UA71 供应商 捷多邦, 专业 PCB 打样工厂, 小时加急出货 µa71, µa71y Short-Circuit Protection Offset-Voltage Null Capability Large Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption
More informationAVAILABLE OPTIONS CERAMIC DIP (J) 6 mv ua747cd ua747cn. 5 mv ua747mj ua747mw ua747mfk
SLOS9A D97, FEBRUARY 97 REVISED OCTOBER 99 No Frequency Compensation Required Low Power Consumption Short-Circuit Protection Offset-Voltage Null Capability Wide Common-Mode and Differential Voltage Ranges
More informationMC1458, MC1558 DUAL GENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Short-Circuit Protection Wide Common-Mode and Differential oltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Designed to Be Interchangeable With Motorola MC/MC and Signetics
More informationAVAILABLE OPTIONS CERAMIC DIP (J) CERAMIC DIP (JG) TL071CPWLE 6 mv TL071ACD TL071ACP 3 mv TL071BCD TL071BCP TL072CP
Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion.3% Typ TL7, TL7A, TL7B, TL72 Low
More informationLM139, LM139A, LM239, LM239A, LM339 LM339A, LM339Y, LM2901, LM2901Q QUAD DIFFERENTIAL COMPARATORS SLCS006C OCTOBER 1979 REVISED NOVEMBER 1996
Single Supply or Dual Supplies Wide Range of Supply Voltage 2 V to 36 V Low Supply-Current Drain Independent of Supply Voltage... 0.8 ma Typ Low Input Bias Current...25 na Typ Low Input Offset Current...3
More information15 DEVICES COVER COMMERCIAL, INDUSTRIAL, AND MILITARY TEMPERATURE RANGES AVAILABLE OPTIONS CERAMIC DIP (J) CERAMIC DIP (JG)
TL7, TL7A, TL7B, TL72 SLOS8D SEPTERMBER 978 REVISED AUGUST 996 Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection
More informationua733c, ua733m DIFFERENTIAL VIDEO AMPLIFIERS
-MHz Bandwidth -kω Input Resistance Selectable Nominal Amplification of,, or No Frequency Compensation Required Designed to be Interchangeable With Fairchild ua7c and ua7m description The ua7 is a monolithic
More informationAVAILABLE OPTIONS CERAMIC DIP (J) CERAMIC DIP (JG) TL071CPWLE 6 mv TL071ACD TL071ACP 3 mv TL071BCD TL071BCP TL072CP
Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion.3% Typ TL7, TL7A, TL7B, TL72 Low
More informationLM139, LM139A, LM239, LM239A, LM339, LM339A, LM339Y, LM2901 QUAD DIFFERENTIAL COMPARATORS
Single Supply or Dual Supplies Wide Range of Supply Voltage...2 V to 36 V Low Supply-Current Drain Independent of Supply Voltage... 0.8 ma Typ Low Input Bias Current... 25 Typ Low Input Offset Current...3
More informationLM111, LM211, LM311, LM311Y DIFFERENTIAL COMPARATORS WITH STROBES
Fast Response Times Strobe Capability Maximum Input Bias Current...3 na Maximum Input Offset Current...7 na Can Operate From Single -V Supply Designed Be Interchangeable With National Semiconducr LM, LM,
More informationTL494M PULSE-WIDTH-MODULATION CONTROL CIRCUIT
Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More information24 DEVICES COVER COMMERCIAL, INDUSTRIAL, AND MILITARY TEMPERATURE RANGES. High Input Impedance...JFET-Input Stage Wide Common-Mode and Differential
SLOS8C FEBRUARY 977 REVISED SEPTEMBER 996 2 DEVICES COVER COMMERCIAL, INDUSTRIAL, AND MILITARY TEMPERATURE RANGES Low Power Consumption High Input Impedance...JFET-Input Stage Wide Common-Mode and Differential
More informationGENERAL-PURPOSE OPERATIONAL AMPLIFIERS
Short-Circuit Protection Offset-Voltage Null Capability Large Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Designed to Be Interchangeable
More informationTL494C, TL494I, TL494M, TL494Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationTL594C, TL594I, TL594Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationLM124, LM124A, LM224, LM224A LM324, LM324A, LM2902 QUADRUPLE OPERATIONAL AMPLIFIERS
Wide Range of Supply Voltages: Single Supply...3 V to 30 V (LM2902 3 V to 26 V) or Dual Supplies Low Supply Drain Independent of Supply Voltage... 0.8 Typ Common-Mode Input Voltage Range Includes Ground
More informationTL1451AC, TL1451AY DUAL PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS4C FEBRUARY 983 REVISED OCTOBER 995 Complete PWM Power Control Circuitry Completely Synchronized Operation Internal Undervoltage Lockout Protection Wide Supply Voltage Range Internal Short-Circuit
More informationMC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS
MC89, MC89A, SN89, SN89A, SN789, SN789A SLLS9B SEPTEMPER 97 REVISED MAY 99 Input Resistance... kω to 7 kω Input Signal Range...± V Operate From Single -V Supply Built-In Input Hysteresis (Double Thresholds)
More informationTHS MHz HIGH-SPEED AMPLIFIER
THS41 27-MHz HIGH-SPEED AMPLIFIER Very High Speed 27 MHz Bandwidth (Gain = 1, 3 db) 4 V/µsec Slew Rate 4-ns Settling Time (.1%) High Output Drive, I O = 1 ma Excellent Video Performance 6 MHz Bandwidth
More informationSN54ALS688, SN74ALS688 8-BIT IDENTITY COMPARATORS
Compare Two -Bit Words Totem-Pole Outputs () ALS Are Identical to ALS2 Package Options Include Plastic Small-Outline (DW) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J)
More informationIMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the
More informationua9637ac DUAL DIFFERENTIAL LINE RECEIVER
ua967ac Meets or Exceeds the Requirements of ANSI Standards EIA/TIA--B and EIA/TIA--B and ITU Recommendations V. and V. Operates From Single -V Power Supply Wide Common-Mode Voltage Range High Input Impedance
More informationSN54HC04, SN74HC04 HEX INVERTERS
SCLS07B DECEMBER 92 REVISED MAY 997 Package Options Include Plastic Small-Outline (D), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), and Ceramic Flat (W) Packages, Ceramic Chip Carriers (FK),
More informationSN75150 DUAL LINE DRIVER
Meets or Exceeds the Requirement of ANSI EIA/TIA-232-E and ITU Recommendation V.28 Withstands Sustained Output Short Circuit to Any Low-Impedance Voltage Between 25 V and 25 V 2-µs Max Transition Time
More informationTL594 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More information54ACT11020, 74ACT11020 DUAL 4-INPUT POSITIVE-NAND GATES
Inputs Are TTL-Voltage Compatible Flow-Through Architecture to Optimize PCB Layout Center-Pin V CC and GND Configurations to Minimize High-Speed Switching Noise EPIC (Enhanced-Performance Implanted CMOS)
More informationSN54ALS00A, SN54AS00, SN74ALS00A, SN74AS00 QUADRUPLE 2-INPUT POSITIVE-NAND GATES
Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description These devices contain four independent 2-input positive-nand
More informationTL594 PULSE-WIDTH-MODULATION CONTROL CIRCUIT
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationSN54ACT00, SN74ACT00 QUADRUPLE 2-INPUT POSITIVE-NAND GATES
SCAS AUGUST 99 REVISED MAY 99 Inputs Are TTL-Voltage Compatible EPIC (Enhanced-Performance Implanted CMOS) -µm Process Package Options Include Plastic Small-Outline (D), Shrink Small-Outline (DB), Thin
More informationPRECISION VOLTAGE REGULATORS
SLVS057B AUGUST 1972 RESED AUGUST 1995 150-mA Load Current Without External Power Transistor Typically 0.02% Input Regulation and 0.03% Load Regulation (µa723m) Adjustable Current Limiting Capability Input
More informationTIL300, TIL300A PRECISION LINEAR OPTOCOUPLER
ac or dc Signal Coupling Wide Bandwidth...>200 khz High Transfer-Gain Stability...±0.0%/ C 00 V Peak Isolation UL Approval Pending Applications Power-Supply Feedback Medical-Sensor Isolation Opto Direct-Access
More informationTL1431 PRECISION PROGRAMMABLE REFERENCE
PRECISION PROGRAMMABLE REFEREE 0.4% Initial Voltage Tolerance 0.2-Ω Typical Output Impedance Fast Turnon... 500 ns Sink Current Capability...1 ma to 100 ma Low Reference Current (REF) Adjustable Output
More informationAVAILABLE OPTIONS CERAMIC DIP (J) 6 mv ua747cd ua747cn. 5 mv ua747mj ua747mw ua747mfk
SLOS9A D971, FEBRUARY 1971 REVISED OCTOBER 199 No Frequency Compensation Required Low Power Consumption Short-Circuit Protection Offset-Voltage Null Capability Wide Common-Mode and Differential Voltage
More informationSN75158 DUAL DIFFERENTIAL LINE DRIVER
SN78 Meets or Exceeds the Requirements of ANSI EIA/TIA--B and ITU Recommendation V. Single -V Supply Balanced-Line Operation TTL Compatible High Output Impedance in Power-Off Condition High-Current Active-Pullup
More informationOP07C PRECISION OPERATIONAL AMPLIFIERS
OP0C PRECISION OPERATIONAL AMPLIFIERS Low Noise No External Components Required Replace Chopper Amplifiers at a Lower Cost Wide Input-Voltage Range...0 to ± V Typ Wide Supply-Voltage Range...± V to ± V
More informationTLC271, TLC271A, TLC271B LinCMOS PROGRAMMABLE LOW-POWER OPERATIONAL AMPLIFIERS
Input Offset Voltage Drift...Typically. µv/month, Including the First 3 Days Wide Range of Supply Voltages Over Specified Temperature Range: C 7 C...3 V 6 V 4 C 85 C...4 V 6 V 55 C 25 C...5 V 6 V Single-Supply
More informationSN55115, SN75115 DUAL DIFFERENTIAL RECEIVERS
SN, SN7 Choice of Open-Collector or Active Pullup (Totem-Pole) Outputs Single -V Supply Differential Line Operation Dual-Channel Operation TTL Compatible ± -V Common-Mode Input Voltage Range Optional-Use
More information6N135, 6N136, HCPL4502 OPTOCOUPLERS/OPTOISOLATORS
Compatible with TTL Inputs High-Speed Switching... Mbit/s Typ Bandwidth...2 MHz Typ High Common-Mode Transient Immunity... 000 V/µs Typ High-Voltage Electrical Insulation... 3000 Vdc Min Open-Collector
More informationSN55451B, SN55452B, SN55453B, SN55454B SN75451B, SN75452B, SN75453B, SN75454B DUAL PERIPHERAL DRIVERS
PERIPHERAL DRIVERS FOR HIGH-CURRENT SWITCHING AT VERY HIGH SPEEDS Characterized for Use to 00 ma High-Voltage Outputs No Output Latch-Up at 0 V (After Conducting 00 ma) High-Speed Switching Circuit Flexibility
More informationLM158, LM158A, LM258, LM258A LM358, LM358A, LM2904, LM2904Q DUAL OPERATIONAL AMPLIFIERS
Wide Range of Supply oltages: Single Supply...3 to 30 (LM2904 and LM2904Q...3 to 26 ) or Dual Supplies Low Supply-Current Drain Independent of Supply oltage... 0.7 Typ Common-Mode Input oltage Range Includes
More informationTLE2141, TLE2141A, TLE2141Y EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
Low Noise 1 Hz...15 n/ Hz 1 khz...1.5 n/ Hz 1 -pf Load Capability 2-mA Min Short-Circuit Output Current 27-/µs Min Slew Rate High Gain-Bandwidth Product...5.9 MHz Low IO... 5 µ Max at 25 C Single or Split
More informationTLC226x, TLC226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS
Output Swing includes Both Supply Rails Low Noise... 2 nv/ Hz Typ at f = khz Low Input Bias Current... pa Typ Fully Specified for Both Single-Supply and Split-Supply Operation Low Power... µa Max Common-Mode
More informationSN54HC373, SN74HC373 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCLS140B DECEMBER 1982 REVISED MAY 1997
Eight High-Current Latches in a Single Package High-Current -State True s Can Drive up to LSTTL Loads Full Parallel Access for Loading Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline
More informationTL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationSN54HC573A, SN74HC573A OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCLS147B DECEMBER 1982 REVISED MAY 1997
High-Current -State s Drive Bus Lines Directly or up to LSTTL Loads Bus-Structured Pinout Package Options Include Plastic Small-Outline (DW) and Ceramic Flat (W) Packages, Ceramic Chip Carriers (FK), and
More informationdescription V CC 2CLR 2D 2CLK 2PRE 2Q 2Q 1CLR 1D 1CLK 1PRE 1Q 1Q GND 2CLR 1CLR 1CLK NC 1PRE NC 1Q 2CLK 2PRE GND
Package Optio Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs TYPE TYPICAL MAXIMUM CLOCK FREUEY (CL = 0 pf) (MHz) TYPICAL POWER
More informationSN54ALS873B, SN54AS873A, SN74ALS873B, SN74AS873A DUAL 4-BIT D-TYPE LATCHES WITH 3-STATE OUTPUTS SDAS036D APRIL 1982 REVISED AUGUST 1995
3-State Buffer-Type Outputs Drive Bus Lines Directly Bus-Structured Pinout Package Optio Include Plastic Small-Outline (DW) Packages, Ceramic Chip Carriers (FK), and Plastic (NT) and Ceramic (JT) DIPs
More informationPRODUCT PREVIEW SN54AHCT257, SN74AHCT257 QUADRUPLE 2-LINE TO 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS. description
Inputs Are TTL-Voltage Compatible EPIC (Enhanced-Performance Implanted CMOS) Process Package Options Include Plastic Small-Outline (D), Shrink Small-Outline (DB), Thin Very Small-Outline (DGV), Thin Shrink
More informationEE 230 Lecture 16. Nonideal Op Amp Characteristics
EE 230 Lecture 16 Nonideal Op Amp Characteristics Quiz 11 The dc gain of this circuit was measured to be 5 and the 3dB bandwidth was measured to be 600KHz. Determine as many of the following as possible
More informationTLC227x, TLC227xA, TLC227xY Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS190 FEBRUARY 1997
SLOS19 FEBRUARY 1997 Output Swing Includes Both Supply Rails Low Noise...9 nv/ Hz Typ at f = 1 khz Low Input Bias Current...1 pa Typ Fully Specified for Both Single-Supply and Split-Supply Operation Common-Mode
More informationSN5407, SN5417, SN7407, SN7417 HEX BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS SDLS032A DECEMBER 1983 REVISED NOVEMBER 1997
Converts TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping Diodes Simplify System Design Open-Collector Driver for Indicator Lamps and Relays s Fully Compatible With Most TTL Circuits
More informationSN54ALS08, SN54AS08, SN74ALS08, SN74AS08 QUADRUPLE 2-INPUT POSITIVE-AND GATES
SNALS0, SNAS0, SN7ALS0, SN7AS0 Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description These devices contain
More informationTL780 SERIES POSITIVE-VOLTAGE REGULATORS
±1% Output Tolerance at ±2% Output Tolerance Over Full Operating Range Thermal Shutdown description Internal Short-Circuit Current Limiting Pinout Identical to µa7800 Series Improved Version of µa7800
More informationSN54HC373, SN74HC373 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS
Eight High-Current Latches in a Single Package High-Current -State True s Can Drive up to LSTTL Loads Full Parallel Access for Loading Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline
More informationTLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS
Output Swing Includes Both Supply Rails Low Noise... 2 nv/ Hz Typ at f = khz Low Input Bias Current... pa Typ Fully Specified for Both Single-Supply and Split-Supply Operation Low Power... 5 µa Max Common-Mode
More informationTL598 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Function Totem-Pole Outputs for 200-mA Sink or Source Current Output Control Selects Parallel or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either Output
More informationNE556, SA556, SE556, SE556C DUAL PRECISION TIMERS
Two Precision Timing Circuits per Package Astable or Monostable Operation TTL-Compatible Output Can Sink or Source Up to 50 ma Active Pullup or Pulldown Designed to be Interchangeable With Signetics SE556,
More informationSN54HC00, SN74HC00 QUADRUPLE 2-INPUT POSITIVE-NAND GATES
Package Options Include Plastic Small-Outline (D), Thin Shrink Small-Outline (PW), and Ceramic Flat (W) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description
More informationSN54HC245, SN74HC245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
High-Current -State s Drive Bus Lines Directly or up to LSTTL Loads Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), and Ceramic Flat (W) Packages,
More informationMC3487 QUADRUPLE DIFFERENTIAL LINE DRIVER
Meets or Exceeds Requirements of ANSI EIA/TIA-422-B and ITU Recommendation V. -State, TTL-Compatible s Fast Transition Times High-Impedance Inputs Single -V Supply Power-Up and Power-Down Protection Designed
More informationSN54HC365, SN74HC365 HEX BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
High-Current -State s Drive Bus Lines, Buffer Memory Address Registers, or Drive up to LSTTL Loads True s Package Options Include Plastic Small-Outline (D) and Ceramic Flat (W) Packages, Ceramic Chip Carriers
More informationCopyright Each Manufacturing Company.
Free DataSheet Search and Download Site. Free electronic engineering tool that enables you to locate product datasheets from hundreds of electronic component manufacturers worldwide. Copyright Each Manufacturing
More informationSN54HC377, SN74HC377 OCTAL D-TYPE FLIP-FLOPS WITH CLOCK ENABLE
Eight Flip-Flops With Single-Rail Outputs Clock Enable Latched to Avoid False Clocking Applications Include: Buffer/Storage Registers Shift Registers Pattern Generators Package Options Include Plastic
More informationLM1458/LM1458C. Dual Operational Amplifier. Features. Description. Internal Block Diagram.
Dual Operational Amplifier www.fairchildsemi.com Features Internal frequency compensation Short circuit protecion Large common mode and differential voltage range No latch up Low power consumption Description
More informationKA741. Single Operational Amplifier. Features. Description. Internal Block Diagram.
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationSN54HC132, SN74HC132 QUADRUPLE POSITIVE-NAND GATES WITH SCHMITT-TRIGGER INPUTS
Operation From Very Slow Input Transitions Temperature-Compensated Threshold Levels High Noise Immunity Same Pinouts as HC00 Package Options Include Plastic Small-Outline (D), Shrink Small-Outline (DB),
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
More informationTHS6092, THS ma, +12 V ADSL CPE LINE DRIVERS
Remote Terminal ADSL Line Driver Ideal for Both Full Rate ADSL and G.Lite Compatible With 1:2 Transformer Ratio Wide Supply Voltage Range 5 V to 14 V Ideal for Single Supply 12-V Operation Low 2.1 pa/
More informationDual operational amplifier
DESCRIPTION The 77 is a pair of high-performance monolithic operational amplifiers constructed on a single silicon chip. High common-mode voltage range and absence of latch-up make the 77 ideal for use
More informationSN54AHCT174, SN74AHCT174 HEX D-TYPE FLIP-FLOPS WITH CLEAR
Inputs Are TTL-Voltage Compatible EPIC (Enhanced-Performance Implanted CMOS) Process Contain Six Flip-Flops With Single-Rail s Applicatio Include: Buffer/Storage Registers Shift Registers Pattern Generators
More informationUC284x, UC384x, UC384xY CURRENT-MODE PWM CONTROLLERS
Optimized for Off-Line and dc-to-dc Converters Low Start-Up Current (
More informationSN54AS825A, SN74AS825A 8-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SDAS020B JUNE 1984 REVISED AUGUST 1995
Functionally Equivalent to AMD s AM2982 Improved I OH Specificatio Multiple Output Enables Allow Multiuser Control of the Interface Outputs Have Undershoot-Protection Circuitry Power-Up High-Impedance
More informationSN54HC175, SN74HC175 QUADRUPLE D-TYPE FLIP-FLOPS WITH CLEAR
Contain Four Flip-Flops With Double-Rail Outputs Applications Include: Buffer/Storage Registers Shift Registers Pattern Generators Package Options Include Plastic Small-Outline (D), Thin Shrink Small-Outline
More informationTL 072 S G Green G : Green. TL072SG-13 S SOP-8L 2500/Tape & Reel -13
Features General Description Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion 0.003%
More informationSN54ALS873B, SN54AS873A, SN74ALS873B, SN74AS873A DUAL 4-BIT D-TYPE LATCHES WITH 3-STATE OUTPUTS SDAS036D APRIL 1982 REVISED AUGUST 1995
3-State Buffer-Type Outputs Drive Bus Lines Directly Bus-Structured Pinout Package Optio Include Plastic Small-Outline (DW) Packages, Ceramic Chip Carriers (FK), and Plastic (NT) and Ceramic (JT) DIPs
More informationAdvanced Regulating Pulse Width Modulators
Advanced Regulating Pulse Width Modulators FEATURES Complete PWM Power Control Circuitry Uncommitted Outputs for Single-ended or Push-pull Applications Low Standby Current 8mA Typical Interchangeable with
More informationSN75150 DUAL LINE DRIVER
Meets or Exceeds the Requirement of TIA/EIA-232-F and ITU Recommendation V.28 Withstands Sustained Output Short Circuit to Any Low-Impedance Voltage Between 25 V and 25 V 2-µs Maximum Transition Time Through
More informationSN75C1406 TRIPLE LOW-POWER DRIVERS/RECEIVERS
Meet or Exceed the Requirements of ANSI EIA/TIA-232-E and ITU Recommendation V.28 Very Low Power Consumption 5 mw Typ Wide Driver Supply Voltage Range ±4.5 V to ±15 V Driver Output Slew Rate Limited to
More informationREI Datasheet. UC494A, UC494AC, UC495A, UC495AC Advanced Regulatin Pulse Width Modulators. Quality Overview
UC494A, UC494AC, UC495A, UC495AC Advanced Regulatin Pulse Width Modulators REI Datasheet This entire series of PWM modulators each provide a complete pulse width modulation system in a single monolithic
More informationSN54ALS74A, SN54AS74A, SN74ALS74A, SN74AS74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH CLEAR AND PRESET
Package Optio Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs TYPE TYPICAL MAXIMUM CLOCK FREUEY (CL = 0 pf) (MHz) TYPICAL POWER
More information54ACT11109, 74ACT11109 DUAL J-K POSITIVE-EDGE-TRIGGERED FLIP-FLOPS WITH CLEAR AND PRESET
Inputs Are TTL-Voltage Compatible Flow-Through Architecture Optimizes PCB Layout Center-Pin V CC and GND Configuratio Minimize High-Speed Switching Noise EPIC (Enhanced-Performance Implanted CMOS) 1-µm
More informationTLE2227, TLE2227Y, TLE2237, TLE2237Y EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION DUAL OPERATIONAL AMPLIFIERS
Outstanding Combination of DC Precision and AC Performance: Unity-Gain Bandwidth... 15 MHz Typ V n... 3.3 nv/ Hz at f = 1 Hz Typ,.5 nv/ Hz at f = 1 khz Typ V IO... 1 µv Typ A VD... 5 V/µV Typ With R L
More informationTL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
More informationTL497AC, TL497AI, TL497AY SWITCHING VOLTAGE REGULATORS
High Efficiency...60% or Greater Output Current...500 ma Input Current Limit Protection TTL-Compatible Inhibit Adjustable Output Voltage Input Regulation... 0.2% Typ Output Regulation... 0.4% Typ Soft
More informationSN5407, SN5417, SN7407, SN7417 HEX BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS
Converts TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping Diodes Simplify System Design Open-Collector Driver for Indicator Lamps and Relays s Fully Compatible With Most TTL Circuits
More informationTL431, TL431A ADJUSTABLE PRECISION SHUNT REGULATORS
Equivalent Full-Range Temperature Coefficient... 30 ppm/ C 0.2-Ω Typical Output Impedance Sink-Current Capability...1 ma to 100 ma Low Output Noise Adjustable Output Voltage...V ref to 36 V Available in
More informationSN75174 QUADRUPLE DIFFERENTIAL LINE DRIVER
SN Meets or Exceeds the Requirements of ANSI Standards EIA/TIA--B and RS-8 and ITU Recommendation V.. Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments -State s Common-Mode Voltage
More informationTL7702B, TL7705B, TL7702BY, TL7705BY SUPPLY VOLTAGE SUPERVISORS
Power-On Reset Generator Automatic Reset Generation After Voltage Drop Output Defined From V CC 1 V Precision Voltage Seor Temperature-Compeated Voltage Reference True and Complement Reset Outputs Externally
More informationSN54HCT373, SN74HCT373 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS
Inputs Are TTL-Voltage Compatible Eight High-Current Latches in a Single Package High-Current -State True s Can Drive up to LSTTL Loads Full Parallel Access for Loading Package Optio Include Plastic Small-Outline
More informationKA3303/KA3403. Quad Operational Amplifier. Features. Description. Internal Block Diagram.
Quad Operational Amplifier www.fairchildsemi.com Features Output voltage can swing to GND or negative supply Wide power supply range; Single supply of 3.0V to 36V Dual supply of ±1.5V to ±18V Electrical
More informationSN QUADRUPLE HALF-H DRIVER
-A -Current Capability Per Driver Applications Include Half-H and Full-H Solenoid Drivers and Motor Drivers Designed for Positive-Supply Applications Wide Supply-Voltage Range of 4.5 V to 6 V TTL- and
More information