Fusible, Non-Flammable Metal Film Leaded Resistors

Transcription

1 NFR25, NFR25H Fusible, Non-Flammable Metal Film DESCRIPTION A homogeneous film of metal alloy is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned connecting wires of electrolytic copper are welded to the end-caps. The resistors are coated with a grey, flame retardant lacquer which provides electrical, mechanical, and climatic protection. The encapsulant is resistant to all cleaning solvents in accordance with IEC FEATURES Technology: Metal film Overload protection without risk of fire Wide range of overload currents (refer Fusing Characteristics graphs) Lead (Pb)-free solder contacts Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes Compatible to RoHS directive 22/95/EC APPLICATIONS Audio Video TECHNICAL SPECIFICATIONS DESCRIPTION UNIT NFR25 NFR25H Resistance Range () Ω.22 to 5k.22 to 5k Resistance Tolerance % ± 5 ± 5 Resistance Series E24 E24 Rated Dissipation, P 7 W.33.5 Thermal Resistance (R th ) K/W 24 5 Temperature Coefficient.22 Ω R 4.7 Ω ± 2 ± 2 ppm/k 4.7 Ω < R 5 Ω ± 2 ± 5 Ω < R 5 kω ± ± Operating Voltage, U max. DC or RMS V Basic Specifications IEC 6 5- IEC 6 5- Climatic Category (IEC 668-) 55/55/56 55/55/56 Max. Resistance Change for Resistance Range, ΔR max., after: Load ( h, P 7 ): ± ( % R +.5 Ω) ± ( % R +.5 Ω) Long Term Damp Heat Test (56 Days): ± ( % R +.5 Ω) ± ( % R +.5 Ω) Soldering (26 C, s): ± (.25 % R +.5 Ω) ± (.25 % R +.5 Ω) Notes R value is measured with probe distance of 24 mm ± mm using 4-terminal method () Ohmic values (other than resistance range) are available on request For technical questions, contact: filmresistorsleaded@vishay.com Document Number: Revision: 3-Mar-

2 Fusible, Non-Flammable Metal Film NFR25, NFR25H PACKAGING MODEL TAPING AMMOPACK REEL PIECES CODE PIECES CODE NFR25, NFR25H Axial, 52 mm 5 A5 A 5 R5 NFR25, NFR25H Radial 4 N4 - - DIMENSIONS L Ø d Ø D L 2 Outline DIMENSIONS (Resistor Types, Mass and Relevant Physical Dimensions) TYPE D max. (mm) L max. (mm) L 2 max. (mm) Ø d (mm) MASS (mg) NFR25 NFR25H ±.5 2 PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: NFR25227JA N F R J A MODEL/SIZE VARIANT TCR/MATERIAL VALUE TOLERANCE PACKAGING () SPECIAL NFR25 J = ± 5 % NFR25H = Neutral Z = Value overload (Special) PRODUCT DESCRIPTION: NFR25 5 % A R22 = Standard 3 digit value digit multiplier MULTIPLIER 7 = * -3 8 = * -2 9 = * - = * = * 2 = * 2 NFR25 5 % A R22 Notes The PART NUMBER is shown to facilitate the introduction of a unified part numbering system for ordering products () Please refer packaging table N4 A5 A R5 The 2 digits are used for all special parts. = Standard MODEL/SIZE TOLERANCE PACKAGING () RESISTANCE VALUE NFR25 NFR25H ± 5 % N4 A5 A R5 K = kω 4R7 = 4.7 Ω Document Number: For technical questions, contact: filmresistorsleaded@vishay.com Revision: 3-Mar- 2

3 NFR25, NFR25H Fusible, Non-Flammable Metal Film PRODUCTS WITH RADIAL LEADS (NFR25, NFR25H) P 2 P H H H L L W W F P P D DIMENSIONS (Radial Taping) SYMBOL PARAMETER VALUE TOLERANCE UNIT P Pitch of components 2.7 ±. mm P Feed-hole pitch 2.7 ±.2 mm P Feed-hole centre to lead at topside at the tape 3.85 ±.5 mm P 2 Feed-hole center to body center 6.35 ±. mm F Lead-to-lead distance /- mm W Tape width 8. ±.5 mm W Minimum hold down tape width mm H Component height 29. Max. mm H Lead wire clinch height 6.5 ±.5 mm H Height of component from tape center 9.5 ± mm D Feed-hole diameter 4. ±.2 mm L Maximum length of snipped lead. - mm L Minimum lead wire (tape portion) shortest lead mm Note Please refer document number 2872 Packaging for more detail MARKING The nominal resistance and tolerance are marked on the resistor using four colored bands in accordance with IEC 662, marking codes for resistors and capacitors. For ease of recognition a fifth ring is added, which is violet for type NFR25 and white for type NFR25H. FUNCTIONAL PERFORMANCE, PRODUCT CHARACTERIZATION Standard values of nominal resistance are taken from the E24 series for resistors with a tolerance of ± 5 %. The values of the E24 series are in accordance with IEC 663. OUTLINES The length of the body (L ) is measured by inserting the leads into holes of two identical gauge plates and moving these plates parallel to each other until the resistor body is clamped without deformation (IEC 6294). LIMITING VALUES TYPE LIMITING VOLTAGE U () (V) LIMITING POWER P 7 NFR NFR25H 35.5 Note () The maximum voltage that may be continuously applied to the resistor element, see IEC 65-. The maximum permissible hot-spot temperature is 55 C. For technical questions, contact: filmresistorsleaded@vishay.com Document Number: Revision: 3-Mar-

4 Fusible, Non-Flammable Metal Film NFR25, NFR25H DERATING The power that the resistor can dissipate depends on the operating temperature. P max. (% P rated ) 5 Maximum dissipation (P max. ) in percentage of rated power as a function of the ambient temperature (T amb ) FUSING CHARACTERISTICS T amb ( C) The resistors will fuse without the risk of fire and within an indicated range of overload. Fusing means that the resistive value of the resistor increases at least times. The fusing characteristic is measured under constant voltage. 5 3 t 2 3 t P overload NFR25 This graph is based on measured data which may deviate according to the application. Fusing Characteristics: Ω P overload NFR25 This graph is based on measured data which may deviate according to the application. Fusing Characteristics: Ω R 5 Ω 3 t P overload NFR25 This graph is based on measured data which may deviate according to the application. Fusing Characteristics: 5 Ω R 5 kω Document Number: For technical questions, contact: filmresistorsleaded@vishay.com Revision: 3-Mar- 4

5 NFR25, NFR25H Fusible, Non-Flammable Metal Film FUSING CHARACTERISTICS 3 t 2 3 t P overload NFR25H This graph is based on measured data which may deviate according to the application. Fusing Characteristics: Ω P overload NFR25H This graph is based on measured data which may deviate according to the application. Fusing Characteristic: Ω R 5 kω PULSE LOADING CAPABILITIES 3 Pˆ max. 2 t p /t i = t i NFR25 Pulse on a regular basis; maximum permissible peak pulse power (Pˆ max. ) as a function of pulse duration (t i ),.22 Ω R < 5 Ω 3 Pˆ max. 2 t p /t i = ti NFR25 Pulse on a regular basis; maximum permissible peak pulse power (Pˆ max. ) as a function of pulse duration (t i ), 5 Ω R 5 kω For technical questions, contact: filmresistorsleaded@vishay.com Document Number: Revision: 3-Mar-

6 Fusible, Non-Flammable Metal Film NFR25, NFR25H PULSE LOADING CAPABILITIES 6 ˆ (V) 5 U max t i NFR25 Pulse on a regular basis; maximum permissible peak pulse voltage (Uˆ max. ) as a function of pulse duration (t i ) 3 Pˆ max. 2 t p /t i = ti NFR25H Pulse on a regular basis; maximum permissible peak pulse power (Pˆ max. ) as a function of pulse duration (t i ) 2 ˆ (V) U max t i NFR25H Pulse on a regular basis; maximum permissible peak pulse voltage (Uˆ max. ) as a function of pulse duration (t i ) Document Number: For technical questions, contact: filmresistorsleaded@vishay.com Revision: 3-Mar- 6

7 NFR25, NFR25H Fusible, Non-Flammable Metal Film APPLICATION INFORMATION ΔT (K) 8 ΔT (K) P NFR25 Hot-spot temperature rise (ΔT) as a function of dissipated power P NFR25H Hot-spot temperature rise (ΔT) as a function of dissipated power 5 ΔT (K) 4 5 ΔT (K) 4 5 mm mm mm 5 mm 3 2 mm 5 mm P Minimum distance from resistor body to P.C.B. = mm NFR25 Temperature rise (ΔT) at thr lead end (soldering point) as a function of dissipated power at various lead lengths after mounting P Minimum distance from resistor body to P.C.B. = mm NFR25H Temperature rise (ΔT) at thr lead end (soldering point) as a function of dissipated power at various lead lengths after mounting TESTS AND REQUIREMENTES Essentially all tests are carried out in accordance with IEC 65- specification, category LCT/UCT/56 (rated temperature range: Lower category temperature, upper category temperature; damp heat, long term, 56 days). The tests are carried out in accordance with IEC xx test method, Recommended basic climatic and mechanical robustness testing procedure for electronic components and under standard atmospheric conditions according to IEC 668-, 5.3. In the Test Procedures and Requirements table the tests and requirements are listed with reference to the relevant clauses of IEC 65- and IEC xx test methods. A short description of the test procedure is also given. In some instances deviations from the IEC recommendations were necessary for our method of specifying. For inflammability requirements reference is made to IEC 65-. All soldering tests are performed with mildly activated flux. For technical questions, contact: filmresistorsleaded@vishay.com Document Number: Revision: 3-Mar-

8 Fusible, Non-Flammable Metal Film NFR25, NFR25H TEST PROCEDURES AND REQUIREMENTS IEC 65- CLAUSE IEC TEST METHOD TEST PROCEDURE NFR25 REQUIREMENTS NFR25H 4.4. Visual examination No holes; clean surface; no damage Dimensions (outline) Gauge (mm) See Dimensions Table (Tb) (Xa) Resistance (refer note on first page for measuring distance) Resistance to soldering heat Component solvent resistance (Ta) Solderability Solderability (after aging) Voltage proof on insulation Robustness of terminations: Applied voltage (+ %/- %): R < Ω:. V Ω R < Ω:.3 V Ω R < kω: V kω R < kω: 3 V kω R 5 kω: V Thermal shock: s; 26 C; 3 mm from body Isopropyl alcohol or H 2 O followed by brushing 2 s; 235 C: Solder bath method; SnPb4 3 s; 245 C: Solder bath method; SnAg3Cu.5 8 h steam or 6 h, 55 C; leads immersed 6 mm; for 2 s at 235 C: Solder bath (SnPb4) for 3 s at 245 C: Solder bath (SnAg3Cu.5) method U RMS = 5 V during min; metal block method R - R nom. : max. ± 5 % ΔR max.: ± (.25 % R +.5 Ω) No visual damage Good tinning ( 95 % covered); no damage Good tinning ( 95 % covered); no damage No breakdown or flashover (Ua) Tensile all samples Load N; s Number of failures < x (Ub) Bending half number of samples (Uc) Torsion other half of samples 3 x 36 in opposite directions (Eb) Bump 3 x 5 bumps in 3 directions; 4 g (Fc) Vibration (Na) Rapid change of temperature Load 5 N; 4 x 9 Number of failures < x -6 Frequency Hz to 5 Hz; displacement.5 mm or acceleration g; 3 directions; total 6 h (3 x 2 h) 3 min at LCT and 3 min at UCT; 5 cycles 4.23 Climatic sequence: (Ba) Dry heat 6 h; 55 C (Db) Damp heat (accelerated) st cycle 24 h; 55 C; 9 % to % RH (Aa) Cold 2 h; - 55 C (M) Low air pressure 2 h; 8.5 kpa; 5 C to 35 C (Db) Damp heat (accelerated) remaining cycles 5 days; 55 C; 95 % to % RH (Cab) Damp heat (steady state) Endurance (at 7 C) Endurance at upper category temperature 4.8 Temperature coefficient 56 days; 4 C; 9 % to 95 % RH; loaded with. P 7 (IEC steps: V to V) h; loaded with P 7 or U max. ;.5 h ON and.5 h OFF No damage ΔR max.: ± (.25 % R +.5 Ω) No damage ΔR max.: ± (.25 % R +.5 Ω) No damage ΔR max.: ± (.25 % R +.5 Ω) No visual damage ΔR max.: ± (.25 % R +.5 Ω) R ins min.: 3 MΩ ΔR max.: ± (.5 % R +. Ω) R ins min.: 3 MΩ ΔR max.: ± ( % R +.5 Ω) ΔR max.: ± ( % R +.5 Ω) h; no load ΔR max.: ± ( % R +.5 Ω) Between - 55 C and + 55 C.22 Ω R 4.7 Ω 4.7 Ω < R 5 Ω 5 Ω < R 5 kω ± 2 ppm/k ± 2 ppm/k ± ppm/k 4.2 Noise IEC 695 <. μv/v 4.26 Accidental overload Cheese-cloth Non flammable Insulation resistance Maximum voltage U max. DC = 5 V after min; metal block method R ins min.: 4 MΩ ± 2 ppm/k ± ppm/k ± ppm/k Document Number: For technical questions, contact: filmresistorsleaded@vishay.com Revision: 3-Mar- 8

9 NFR25, NFR25H Fusible, Non-Flammable Metal Film 2NC INFORMATION FOR HISTORICAL CODING REFERENCE The resistors have a 2 digit numeric code starting with 23 Last Digit of 2NC Indicating Resistance Decade The subsequent 7 digits indicate the resistor type and packaging The remaining 3 digits indicate the resistance value: - The first 2 digits indicate the resistance value - The last digit indicates the resistance decade RESISTANCE DECADE.22 Ω to.9 Ω Ω to 9. Ω Ω to 9 Ω Ω to 9 Ω LAST DIGIT kω to 9. kω 2 kω to 5 kω 3 2NC (Resistors Type and Packaging) 2NC Example The 2NC of a NFR25 resistor with value 75 Ω, supplied on a bandolier of units in ammopack is: TYPE BANDOLIER IN AMMOPACK BANDOLIER ON REEL RADIAL TAPED STRAIGHT LEADS STRAIGHT LEADS 4 UNITS UNITS 5 UNITS 5 UNITS NFR NFR25H For technical questions, contact: filmresistorsleaded@vishay.com Document Number: Revision: 3-Mar-

10 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2/65/EU of The European Parliament and of the Council of June 8, 2 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 22/95/EC. We confirm that all the products identified as being compliant to Directive 22/95/EC conform to Directive 2/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS79A standards. Please note that some Vishay documentation may still make reference to the IEC definition. We confirm that all the products identified as being compliant to IEC conform to JEDEC JS79A standards. Revision: 2-Oct-2 Document Number: 9