Pin Configuration. Surface Mount 9.00 x 7.01 x 1.50 mm SMP-35B
|
|
- Derek Waters
- 6 years ago
- Views:
Transcription
1 Features For broadband applications Typical 3 bandwidth of 65 High attenuation Singleended operation Ceramic Surface Mount Package (SMP) Replaces Sawtek P/N (BW 3=64 ) Hermetic RoHS compliant (2002/95/EC), Pbfree Pb Package Surface Mount 9.00 x 7.01 x 1. mm SMP35B Pin Configuration Bottom View NOM MAX Singleended Configuration x Pin No. Description 4 Output 5 Output return 9 Input 10 Input return 1,2,3,6,7,8 Case ground Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width +0.10mm/0.15mm Body: Al 2O 3 ceramic Lid: Kovar, Ni plated Terminations: Au plating µm, over a 2 6µm Ni plating Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 1 of 6
2 Electrical Specifications (1) Operating Temperature Range: (2) 0 to +70 o C Parameter (3) Minimum Typical (4) Maximum Unit Center Frequency 140 Minimum Insertion Loss Lower 1 Bandedge (5) Upper 1 Bandedge Lower 3 Bandedge (5) Upper 3 Bandedge Lower 40 Bandedge (5) Upper 40 Bandedge Amplitude Variation pp Phase Linearity deg pp Group Delay Variation ns pp Absolute Delay µsec Relative Attenuation (5) Terminating Source Impedance (6) Ω Terminating Load Impedance (6) Ω Substrate Material 128 LiNbO 3 Temperature Coefficient of Frequency 74 ppm/ o C Notes: 1. All specifications are based on the TriQuint test circuit shown below 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. Electrical margin has been built into the design to account for the variations due to temperature and manufacturing tolerances 4. Typical values are based on average measurements at room temperature 5. All attenuation measurements are measured relative to minimum insertion loss 6. This is the optimum impedance in order to achieve the performance shown Test Circuit: Actual matching values may vary due to PCB layout and parasitics Singleended Input 27nH nH 47pF 33nH 1,2,3,5 22pF 6,7,8,10 Singleended Output Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 2 of 6
3 Electrical Specifications (1) Operating Temperature Range: (2) 40 to +85 o C Parameter (3) Minimum Typical (4) Maximum Unit Center Frequency 140 Minimum Insertion Loss Lower 1.5 Bandedge (5) Upper 1.5 Bandedge Lower 3 Bandedge (5) Upper 3 Bandedge Lower 40 Bandedge (5) Upper 40 Bandedge Amplitude Variation pp Phase Linearity deg pp Group Delay Variation ns pp Absolute Delay µsec Relative Attenuation (5) Terminating Source Impedance (6) Ω Terminating Load Impedance (6) Ω Substrate Material 128 LiNbO 3 Temperature Coefficient of Frequency 74 ppm/ o C Notes: 1. All specifications are based on the TriQuint test circuit shown below 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. Electrical margin has been built into the design to account for the variations due to temperature and manufacturing tolerances 4. Typical values are based on average measurements at room temperature 5. All attenuation measurements are measured relative to minimum insertion loss 6. This is the optimum impedance in order to achieve the performance shown Test Circuit: Actual matching values may vary due to PCB layout and parasitics Singleended Input 27nH nH 47pF 33nH 1,2,3,5 22pF 6,7,8,10 Singleended Output Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 3 of 6
4 Typical Performance (at room temperature) Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 4 of 6
5 Matching Schematics Actual matching values may vary due to PCB layout and parasitics Singleended Input 27nH nH 47pF 33nH 1,2,3,5 22pF 6,7,8,10 Singleended Output Marking PCB Footprint ID dot SAWTEK XXXXXX Date code The date code consists of: day of the current year (Julian, 3 digits), last digit of the year (1 digit) and hour (2 digits) 16.8 Ø330 ID dot Tape and Reel This footprint represents a recommendation only Dimensions shown are nominal in millimeters Ø1.5 A Ø102 Ø20.2 Ø Direction of travel 2.2 Section AA Ø1.5 A Dimensions shown are nominal in millimeters Packaging quantity: 2000 units/reel Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 5 of 6
6 Maximum Ratings Parameter Symbol Minimum Maximum Unit Operating Temperature Range T o C Storage Temperature Range T stg o C Warnings Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure Important Notes RoHS Compliance This product complies with EU directive 2002/95/EC (RoHS) Pb Solderability Compatible with JESD22B102, Pbfree process, 260C peak reflow temperature (see soldering profile) Links to Additional Technical Information PCB Layout Tips Qualification Flowchart Soldering Profile SParameters RoHS Information Other Technical Information TriQuint s liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. TriQuint does not accept any liability for applications, processes, circuits or assemblies, which are implemented using any TriQuint component described in this data sheet. PO Box 6091 Orlando, FL USA Contact Information Phone: +1 (407) Fax: +1 (407) infoproduct@tqs.com Web: Or contact one of our worldwide Network of sales offices, Representatives or distributors Subject to change or obsolescence without notice Rev E 11/07 TriQuint Semiconductor Page 6 of 6
Pin Configuration. Surface Mount x 6.50 x 1.75 mm SMP-75B
Features For broadband applications Typical 3 bandwidth of 4.9 MHz High attenuation Singleended operation Ceramic Surface Mount Package (SMP) Replaces Sawtek P/N 851551 (BW 3=4.5 MHz) Hermetic RoHS compliant
More informationPin Configuration. Surface Mount 7.00 x 5.50 x 1.24 mm
Features For WiBro and WiMAX applications Usable bandwidth 10 MHz High attenuation operation 200 Ω Ceramic Surface Mount Package (SMP) Hermetic RoHS compliant (2002/95/EC), Pbfree Pb 6 MHz SAW Filter Package
More informationPin Configuration. Surface Mount 9.10 x 4.80 x 1.24 mm SMP-35C
Features For multiple applications Usable bandwidth 10 MHz Low loss High attenuation Balanced operation Ceramic Surface Mount Package (SMP) Hermetic RoHS compliant (2002/95/EC), Pbfree Pb Package Surface
More informationPin Configuration. Surface Mount 1.40 x 1.20 x 0.46 mm
Features For Satellite Radio Applications Usable Bandwidth 5 MHz Low Loss Good Selectivity Ceramic Chip Scale Package (CSP) Singleended Input,, 100Ω or 200Ω Hermetic RoHS compliant (2002/95/EC), Pbfree
More informationMHz SAW Filter
Applications Smart metering Remote meter reading wireless modules Licensed band wireless General purpose wireless Product Features Usable bandwidth 15 MHz Low loss Dimensions: 3.80 x 3.80 x 1.27 mm Singleended
More informationMHz SAW Filter
Applications General Purpose For IF applications Product Features Typical 3 db bandwidth of 18.5 MHz Low loss High Attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small Size Dimensions:
More informationMHz SAW Filter
Applications Wireless Infrastructure AMPS, CDMA and TDMA General Purpose RF Filter 4G, MultiStandard Band 1 Uplink Repeaters Product Features SMP12, 3.00 x 3.00 x 1.22 mm Functional Block Diagram 60 MHz
More informationMHz SAW Filter
Applications General Purpose For IF applications Product Features Typical 1 db Bandwidth of 1.2 MHz Low loss High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small Size Dimensions:
More information/881.5 MHz SAW Duplexer
Applications General purpose wireless Femtocells Repeaters Data cards and dongles Product Features Usable bandwidth 25 MHz No matching required for operation at Ω Excellent rejection for Bluetooth and
More informationMHz SAW Filter
Applications Wireless Infrastructure AMPS, CDMA and TDMA General Purpose RF Filter 4G, MultiStandard UMTS Bands 1 and 10 Downlink Repeaters Product Features SMP12, 3.00 x 3.00 x 1.22 mm Functional Block
More informationMHz SAW Filter
Applications Base Station Infrastructure LTE Macrocells General Purpose Wireless Product Features SMP28B 7.1 x 5.51 x 1.63 mm Functional Block Diagram Usable bandwidth of 6 MHz Balanced operation High
More informationGHz WLAN/BT LTE Co-Existence Filter
Applications WiFi bandpass filter that enables the coexistence of 3G/4G/LTE/TDLTE & WiFi signals Highpower WLAN Access Points and Small Cells Bandedge filtering of WiFi signal emissions Smart Meters and
More informationMHz BAW Filter
Applications Satellite Radio antenna modules Satellite Radio devices Suitable for Automotive applications Compliant to the AECQ0 Grade 2 reliability standard CSP 1713, 1.7 X 1.3 X 6 mm Product Features
More informationGHz BAW Filter
Applications WiFi/ ISM notch filter to enable coexistence between WiMAX/LTE/TD-LTE & WiFi/BT/ISM radios Applicable passbands: 2.6 GHz WiMAX/LTE, 2.3 GHz WiMAX/LTE, LTE Bands 7 & 38, TD-LTE Band 40, WCS,
More informationA 2.4 GHz WLAN/BTLTE Co-Existence Filter
Applications Automotive Telematics and Infotainment 2.4 GHz ISM Applications & Smart Energy WiFi bandpass filter that enables the coexistence of 3G/4G/LTE/TD-LTE & WiFi signals WLAN systems (Higher power
More informationTQQ MHz LTE Band 7 Uplink BAW Filter
Applications LTE Band 7 Uplink Infrastructure Base Station General Purpose Wireless 6 Pin 3x3 mm leadless SMT Package Product Features 70 MHz Bandwidth High Attenuation Low Loss 50 Ohm Input/Output Impedance
More informationMHz SAW Filter
85577 Applications General Purpose For WCDMA applications SMP2, 5. x 5. x.32 mm Prouct Features Functional Block Diagram Usable banwith 5 MHz Low loss High attenuation Singleene operation Impeance matching
More informationGHz WLAN/BT LTE Co-Existence Filter
Applications WiFi bandpass filter that enables the coexistence of 4G (WiMAX/LTE/TD-LTE) & WiFi signals Handsets Portable Hotspots Mobile Routers Smart Meters High-power WLAN Access Points Applicable reject
More informationGHz WLAN/BT LTE Co-Existence Filter
Applications WiFi bandpass filter that enables the coexistence of 4G (WiMAX/LTE/TDLTE) & WiFi signals Handsets Portable Hotspots Mobile Routers Smart Meters Highpower WLAN Access Points Applicable reject
More informationDifferential Input / Output Impedance Match SM X 5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week, S=shift) 15 pf
SF1189B-1 Designed for WLAN IF Applications Low Insertion Loss 5.0 x 5.0 x 1.7 mm Suface-Mount Case Single Ended or Differential Input and Output Differential Output Complies with Directive 2002/95/EC
More informationSAW Bandpass Filter F2G12
SAW Bandpass Filter FG Features WCDMA applications Usable bandwidth of 60 MHz No impedance matching require for operation at 50 Ω Ceramic Surface Mounted Device Package (.0 mm *.0 mm ) Singleended Operation
More informationSAW Bandpass Filter F4521
Features RF bandpass filter for CDMA0 CBand Tx. Part Usable bandwidth MHz (0 MHz ~ MHz) High attenuation No matching 0Ω singleended operation Ceramic Surface Mounted Device Package (.8 mm.8 mm ) RoHS compliant
More informationTQQ MHz LTE Band 7 Uplink BAW Filter
Applications LTE Band 7 Uplink Infrastructure Base Station General Purpose Wireless 6 Pin 3 x 3 mm leadless SMT Package Product Features Functional Block Diagram 70 MHz Bandwidth High Attenuation Low Loss
More informationTQQ MHz LTE Band 3 Uplink BAW Filter
Applications LTE Band 3 Uplink Infrastructure Base Station General Purpose Wireless 6 Pin 3 x 3 mm leadless SMT Package Product Features Functional Block Diagram 75 MHz Bandwidth High Attenuation Low Loss
More informationTQQ1013 Band 13 SAW Duplexer
Applications LTE Handsets, Data Cards & Mobile Routers Band 13 777 787 MHz Uplink 746 756 MHz Downlink 8 Pin 2.5 x 2.0 mm Package Product Features NoDrift SAW Technology With Near Zero TCF Low Insertion
More information1640 MHz MHz Temperature Coefficient -30 ppm/ C Operating Temperature T A C
SF1186B-2 Designed for Front End GPS Applications Low Insertion Loss 3.0 x 3.0 x 1.3 mm Surface-Mount Case No Matching Circuit Required Complies with Directive 2002/95/EC (RoHS) Maximum Ratings at +25
More informationTQM EVB B7 BAW Duplexer
Applications LTE handsets, data cards & mobile routers Band 7 2500-2570 MHz Uplink 2620-2690 MHz Downlink 8 Pin 1.6 x 2.0 mm Package Product Features Highly Selective LowDrift BAW Duplexer Low Insertion
More informationTQM EVB. Not for New Designs BC14/BC1/B25 BAW Duplexer. Applications. Functional Block Diagram. Product Features. General Description
TQM96314 Applications CDMA/LTE handset, data card & mobile router applications using the extension PCS band (Band Class 14) / BC1 / B25 8 Pin 2.6 x 2.1 x.88 mm Product Features Excellent Triple Beat Performance:
More informationVectron International Filter specification TFS 243E 1/5
Vectron International Filter specification TFS 243E /5 Measurement condition Ambient temperature T A: 23 C Input power level: 0 dbm Terminating impedance: * Input: 350 Ω -3.8 pf Output: 350 Ω -3.8 pf Characteristics
More informationVectron International Filter specification TFS140AV 1/5
Vectron International Filter specification TFS140AV 1/5 Measurement condition Ambient temperature T A: 23 C Input power level: 0 dbm Terminating impedance: * Input: 50 Ω -78 pf Output: 95 Ω -52 pf Characteristics
More informationSAW BANDPASS FILTER. ACT PART NO.: ACTF9201_2535MHz_DCC6C
SAW BANDPASS FILTER ACT PART NO.: ACTF9201_2535MHz_DCC6C Product Type: SAW Filter Part NO.: Customer: Customer Part NO.: ACTF9201_2535MHz_DCC6C Issued Date: PREPARED BY CHECKED BY APPROVED BY Features
More informationSAW Components Data Sheet B4926
Features Low-loss IF filter for mobile telephone Channel selection in GSM systems Hermetically sealed ceramic SMD package Balanced and unbalanced operation possible No coupling coil required Terminals
More informationACTR Features: ACTR DCC6C v1.1
Features: ACTR9028-934.6-DCC6C v1.1 1-port Resonator Provides reliable, fundamental mode, quartz frequency stabilization i.e. in transmitters or local oscillators Surface Mounted Technology (SMT) Lead-free
More informationVectron International Filter specification TFS1255A 1/5
Vectron International Filter specification TFS1255A 1/5 Measurement condition Ambient temperature T A: 23 C Input power level: m Terminating impedance: Input: 5 Ω Output: 5 Ω Characteristics Remark: The
More informationPART NUMBER: ACTR MHz-DCC6C-75kHz-v1.1 Frequency: MHz
PART NUMBER: ACTR3028-315MHz-DCC6C-75kHz-v1.1 Frequency: 315.000MHz Features 1-port Resonator Provides reliable, fundamental mode, quartz Frequency stabilization i.e. in transmitters or local oscillators
More informationVI TELEFILTER Filter specification TFS 130C 1/5
VI TELEFILTER Filter specification TFS 130C 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 130 Ω -11.6 pf Output: 86 Ω -11.8 pf Characteristics
More informationVectron International Filter specification TFS1590 1/5
Vectron International Filter specification TFS1590 1/5 Measurement condition Ambient temperature T A: 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω Output: 50 Ω Characteristics Remark:
More informationModel BD1631J50100AHF
Model BD1631J51AHF Ultra Low Profile 85 Balun 5Ω to 1Ω Balanced Description The BD1631J51AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output
More informationTGL2201-SM T/R. Wideband Dual Stage VPIN Limiter. Applications. Ordering Information. Part No. ECCN Description
Applications LNA Receiver Chain Protection Military Radar Product Features 2-12 GHz Passive, High Isolation Limiter Low Loss < 1.0 db, X-band Return Loss > 10 db Flat Leakage < 18 dbm Input Power CW Survivability
More informationVectron International Filter specification TFS1575AG 1/5
Vectron International Filter specification TFS1575AG 1/5 Measurement condition Ambient temperature T A: 23 C Input power level: dbm Terminating impedance: Input: 5 Ω Output: 5 Ω Characteristics Remark:
More informationModel C0810J5003AHF. Ultra Low Profile db, 90 Hybrid Coupler
Model C81J53AHF Ultra Low Profile 85 3 db, 9 Hybrid Coupler Description The C81J53AHF is a low cost, low profile sub-miniature high performance 3 db coupler in an easy to use surface mount package. It
More informationVectron International Filter specification TFS246R 1/5
Vectron International Filter specification TFS26R 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedances*): input: 695 Ω -1.9 pf output: 695 Ω -1.9 pf Characteristics
More informationPreliminary. Electrical Characteristics Characteristic Sym Notes Min Typ Max Units
Preliminary SF1202D CDM 450 F-and RF SW Filter 3.8 x 3.8 x 1.4 mm Surface-mount Package Complies with Directive 2002/95/EC (RoHS) bsolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband
More informationModel B0922N7575AHF Rev B. Ultra Low Profile 0404 Balun
Model B9N7575AHF Ultra Low Profile 44 Balun 75Ω to 75Ω Balanced Description The B9N7575AHF is a low profile, low impedance mm square subminiature wideband unbalanced to balanced transformer designed for
More informationModel C2327J5003AHF Rev D
Model C2327J53AHF Ultra Low Profile 85 3 db, 9 Hybrid Coupler Description The C2327J53AHF is a low cost, low profile sub-miniature high performance 3 db coupler in an easy to use surface mount package.
More informationModel BD1722J50100A00
Ultra Low Profile 85 Balun 5Ω to 1Ω Balanced Description The BD1722J51A is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation
More informationModel PD0409J7575S2HF
Model PD49J77SHF Ultra Low Profile 8 Power Divider 7Ω to 7Ω Description The PD49J77SHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49J77SHF is
More informationModel C1517J5003AHF. Ultra Low Profile db, 90 Hybrid Coupler
Model C57J53AHF Ultra Low Profile 85 3 db, 9 Hybrid Coupler Description The C57J53AHF is a low cost, low profile sub-miniature high performance 3 db coupler in an easy to use surface mount package. The
More informationModel PD3150J5050S2HF
Model PD315J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD315J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD315J55S2HF
More informationESDARF02-1BU2CK. Single-line bidirectional ESD protection for high speed interface. Features. Applications. Description
Single-line bidirectional ESD protection for high speed interface Features Datasheet production data Bidirectional device Extra low diode capacitance: 0.2 pf Low leakage current 0201 SMD package size compatible
More informationModel PD2328J5050S2HF
Model PD2328J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD2328J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD2328J55S2HF
More informationVectron International Filter specification TFS455D 1/5
Vectron International Filter specification TFS455D 1/5 Measurement condition Ambient temperature To: 23 C Input power level: dbm Terminating impedance: Input: 5 Ω Output: 5 Ω Characteristics Remark: The
More informationVectron International Filter specification TFS 522 1/5
Vectron International Filter specification TFS 522 1/5 Measurement condition Ambient temperature (T 0): 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω Output: 50 Ω Characteristics Remark:
More informationVectron International Filter specification TFS 400P 1/5
Vectron International Filter specification TFS 400P /5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 280 Ω -6, pf Output: 440 Ω -5,2 pf Characteristics
More informationVS-800 Ultra-Low Jitter High Frequency VCSO
VS-800 Ultra-Low Jitter High Frequency VCSO VS-800 Description The VS-800 is a Voltage Controlled SAW Oscillator that operates at the fundamental frequency of the internal SAW resonator. The SAW resonator
More informationVS-708 Single Frequency VCSO
VS-708 Single Frequency VCSO VS-708 Description The VS-708 is a Voltage Controlled SAW Oscillator that operates at the fundamental or a fraction of the internal SAW filter frequency. The SAW component
More informationVectron International Filter specification TFS180L 1/5
Vectron International Filter specification TFS180L 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 205.51 Ω -23.24 pf Output: 141.63 Ω - 31.49
More informationUM4701/4711/8701/8711
Multi-line ESD/EMI Protection for Color LCD Interfaces UM4701 DFN8 2.0 2.0 UM4711 DFN8 1.7 1.3 UM8701 DFN16 4.0 1.6 UM8711 DFN16 3.3 1.3 General Description The UM4701/UM4711/UM8701/UM8711 is a (L-C) low
More informationVectron International Filter specification TFS /5
Vectron International Filter specification TFS 1226 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 338 Ω -1.6 pf Output: 338 Ω -1.6 pf Characteristics
More informationDetailed Electrical Specifications: Specifications subject to change without notice. Broadband Narrowband 25 C
fee Ultra Low Profile 85 Balun 75Ω to 75Ω Balanced Description The B225J7575AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on
More informationModel BD3238N5050AHF. Ultra Low Profile 0404 Balun
Model BD338N55AHF Ultra Low Profile 44 Balun 5Ω to 5Ω Balanced Description The BD338N55AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and
More informationVectron International Filter specification TFS 1227A 1/5
Vectron International Filter specification TFS 1227A 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω 0 pf Output: 50 Ω 0 pf Characteristics
More informationVVC4 Voltage Controlled Crystal Oscillator
C4 oltage Controlled Crystal Oscillator Features ectron s Smallest CXO, 5.0 X 3.2 X 1.2 mm High Frequencies to 77.70 MHz 5.0 or 3.3 operation Linearity 10% Tri-State Output for testing Low jitter < 1ps
More informationTAT7457-EB. CATV 75 Ω phemt Adjustable Gain RF Amplifier. Applications. Ordering Information
Applications Single-ended and Push-pull Optical Receivers Low-noise Drop Amplifiers Distribution Amplifiers Multi-Dwelling Units Single-ended Gain Block SOT-89 package Product Features Functional Block
More informationVectron International Filter specification TFS /5
Vectron International Filter specification TFS 2096 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 200 Ω -0.38 pf Output: 75 Ω Characteristics
More informationModel BD4859L50100A00 Rev A
Model BD4859L51A Ultra Small Low Profile 63 Balun 5Ω to 1Ω Balanced Description The BD4859L51A is an ultra-small low profile balanced to unbalanced transformer designed for differential inputs and output
More informationVectron International Filter specification TFS 868P 1/5
Vectron International Filter specification TFS 868P 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 80 Ω -1.7 pf Output: 80 Ω -1.7 pf Characteristics
More informationVectron International Filter specification TFS 125P 1/5
Vectron International Filter specification TFS 125P 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 115 Ω -21 pf Output: 110 Ω -35 pf Characteristics
More informationTop View (Near-side) Side View Bottom View (Far-side) ± ±.08. 4x.28. Orientation Marker Balanced port 1.
Model BD2FAHF Ultra Low Profile 168 Balun Ω to Ω Balanced Description The BD2FAHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
More informationTQM BC1/B2 BAW Duplexer
QM2 Not for New Design as an alternative. Applications CDMA / UMTS Handsets Data Cards Mobile Routers PCS Band Class 1 and Band 2 8 Pin 2.6 x 2.1 x 0.0 mm Product Features Functional Block Diagram Excellent
More informationVectron International Filter specification TFS /5
Vectron International Filter specification TFS 2653 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 27,66 Ω -0,01 pf Output: 27,66 Ω -0,01 pf
More informationReturn loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port.
Model BD6N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD6N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output
More informationTGP2107-SM 6 to 18 GHz 6-Bit Digital Phase Shifter ( V C )
TGP217-SM Applications Phased Array Antenna Systems Satellite Communication Systems Electronic Warfare QFN 5x5 mm 32L Product Features Functional Block Diagram Frequency Range: 6 to 18 GHz 6-Bit Digital
More informationVectron International Filter specification TFS 281 1/5
Vectron International Filter specification TFS 281 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 183 Ω -12.5 pf Output: 172 Ω -12.6 pf Characteristics
More informationRF Transformer TCM2-672X+ Surface Mount. 50Ω 1700 to 6700 MHz
Surface Mount top hat RF Transformer 50Ω 1700 to 6700 MHz The Big Deal Wideband, 1700 to 6700 MHz Low insertion loss, 1.1 db Flat insertion loss, ±0.4 db typ. Good input return loss, 12 to 31 db typ. Low
More informationVectron International Filter specification TFS /5
Vectron International Filter specification TFS 2533 1/5 Measurement condition Ambient temperature: 23 C Input power level: dbm Terminating impedance: * Input: 27,22 Ω -,32 pf Output: 27,22 Ω -,32 pf Source:
More informationVI TELEFILTER Filter specification TFS 248F 1/5
VI TELEFILTER Filter specification TFS 248F 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω Output: 200 Ω Characteristics Remark: The reference
More informationVV-701 Voltage Controlled Crystal Oscillator Previous Vectron Model VVC1/VVC2
-701 oltage Controlled Crystal Oscillator Previous ectron Model C1/C2-701 Description ectron s -701 oltage Controlled Crystal Oscillator (CXO) is a quartz stabilized square wave generator with a CMOS output.
More informationQPQ1907SR. 2.4GHz Wi-Fi/BT/LTE Co-Existence BAW Filter. Product Description. Functional Block Diagram. Feature Overview.
2.4GHz Wi-Fi/BT/LTE Co-Existence BAW Filter Product Description The QPQ1907 is a high-performance, high power Bulk Acoustic Wave (BAW) band-pass filter with extremely steep skirts, simultaneously exhibiting
More informationVectron International Filter specification TFS 1632A 1/5
Vectron International Filter specification TFS 1632A 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 183 Ω -0,42 pf Output: 45 Ω -0,47 pf Characteristics
More informationTop View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker.
Model B2F2AHF Ultra Low Profile 168 Balun Ω to 2Ω Balanced Description The B2F2AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
More informationVectron International Filter specification TFS 500 1/5
Vectron International Filter specification TFS 500 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 415 Ω -1 pf Output: 415 Ω -1 pf External
More informationQPQ1237TR7. LTE B3/B7 BAW Diplexer (75MHz/70MHz) Product Overview. Key Features. Functional Block Diagram. Applications.
LTE B3/B7 BAW Diplexer (75MHz/7MHz) Product Overview The is a high performance Bulk Acoustic Wave (BAW) Duplexer designed for Band 3 uplink and Band 7 uplink applications. The provides low insertion loss
More informationModel PD0409J5050S2HF
Model PD49JSHF Ultra Low Profile 8 Power Divider Ω to Ω Description The PD49JSHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49JSHF is ideal for
More informationVectron International Filter specification TFS 737 1/5
Vectron International Filter specification TFS 737 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω Output: 50 Ω Characteristics Remark: The
More informationDescription. Block Diagrams. Figure 1b. Crystal-Based Multiplier w/saw
C-501 oltage Controlled Crystal Oscillator C-501 Description The C-501 is a voltage controlled crystal oscillator that is housed in a hermetic 14.0 x 9.0 x 4.5mm ceramic package. Depending upon the frequency
More informationTGA2583-SM 2.7 to 3.7GHz, 10W GaN Power Amplifier
Applications Commercial and Military Radar QFN 5x5 mm 32L Product Features Functional Block Diagram Frequency Range: 2.7-3.7 GHz P SAT :.5 dbm PAE: > 50 % Small Signal Gain: 33 db Return Loss: > 12 db
More informationMADS T. Schottky Limiter DC - 6 GHz. Features. Functional Schematic. Description. Pin Configuration 3. Ordering Information 1,2.
Features 3 Terminal LPF Broadband Shunt Structure Low Slope Resistance, 7 Ω +3 dbm Peak and CW Power Handling.6 db Shunt Insertion Loss +2 dbm Flat Leakage Power Lead-Free 1. x 1.2 mm 6-lead TDFN Package
More informationTGA2521-SM GHz Linear Driver Amplifier. Key Features. Measured Performance
17-24 GHz Linear Driver Amplifier Key Features Frequency Range: 17-24 GHz 25.5 dbm Nominal Psat, 23.5 dbm Nominal P1dB Gain: 20 db OTOI: 33 dbm Typical Bias: Vd = 5 V, Idq = 320 ma, Vg = -0.5 V Typical
More informationTQP DC-6 GHz Gain Block
Applications Mobile Infrastructure LTE / WCDMA / CDMA / EDGE CATV Point to Point General Purpose Wireless SOT-89 Package Product Features Functional Block Diagram DC-6000 MHz 15.4 db Gain @ 1.9 GHz 4 3.6
More informationUM4501/4511/6501/8501/8511
Multi-line ESD/EMI Protections for Signal ines UM4501 DFN8 2.0 2.0 UM4511 DFN8 1.7 1.3 UM6501 DFN12 3.0 1.6 UM8501 DFN16 4.0 1.6 UM8511 DFN16 3.3 1.3 General Description The UM4501/UM4511/UM6501/UM8501/UM8511
More informationVI TELEFILTER Filter Specification TFS 246 H4 1/5
Filter Specification TFS 246 H4 1/5 Measurement condition Ambient temperature: 2 C Input power level: 0 dbm Terminating impedances *) Input: 490 Ω -2.62 pf Output: 490 Ω -2.62 pf External coil: 270 nh
More informationT1G FS 30W, 28V, DC 6 GHz, GaN RF Power Transistor
Applications Military radar Civilian radar Professional and military radio communications Test instrumentation Wideband or narrowband amplifiers Jammers Product Features Frequency: DC to 6 GHz Output Power
More information50 ohms / matched to ATSAMR21E18 balun transformer, with integrated harmonic filter
50 ohms / matched to ATSAMR21E18 balun transformer, with integrated harmonic filter Datasheet - production data Coated CSP on glass bumpless Description The from STMicroelectronics is an integrated balun,
More informationApplications Ordering Information Part No. ECCN Description TGA2535-SM 3A001.b.2.b X-band Power Amplifier
Applications Point-to-Point Radio X-Band Communications QFN 5x5mm 24L Product Features Functional Block Diagram Frequency Range: 10 12 GHz TOI: 43 dbm Power: 34.5 dbm Psat, 33 dbm P1dB Gain: 24 db Return
More informationVectron International Filter specification TFS1220 1/5
Vectron International Filter specification TFS1220 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 146 Ω -0.9 pf Output: 146 Ω -0.9 pf Characteristics
More informationModel 2425B50-50C Rev. A
rit Model 2425B50-50C Xinger Balun 50Ω to 100Ω Balanced Description The 2425B50-50C is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations
More informationTQP3M9035 High Linearity LNA Gain Block
Applications Repeaters Mobile Infrastructure LTE / WCDMA / CDMA / GSM General Purpose Wireless TDD or FDD systems Product Features 2x2mm 8-lead DFN plastic package Functional Block Diagram 5-4 MHz.66 db
More information17-35GHz MPA/Multiplier TGA4040SM
Not Recommended for New Designs Advance Product Information 17-35GHz MPA/Multiplier TriQuint Recommends the TGA43-SM or TGA431-SM be used for New Designs Key Features Product Description The TriQuint TG44SM
More informationTGA2521-SM GHz Linear Driver Amplifier Key Features Measured Performance
17-24 GHz Linear Driver Amplifier Key Features Frequency Range: 17-24 GHz 25.5 dbm Nominal Psat, 23.5 dbm Nominal P1dB Gain: 20 db OTOI: 33 dbm Typical Bias: Vd = 5 V, Idq = 320 ma, Vg = -0.5 V Typical
More information