Guide To Communication System Pro700

Transcription

1 F A S T A C C E S S C O M M U N I C A T I O N Guide To Communication System Pro700

2 Pro700 Communication System Communication System Pro700 STENTO ASA reserves the right to make changes in specifications of the products detailed in this handbook as well as the contents of this handbook at any time and without notice. This is consistent with our policy of continuous product analysis and improvement. STENTO ASA and its subsidiaries assume no responsibility for any errors that may appear in its documentation, or damages arising from the information in it. No information in this publication should be regarded as a warranty made by STENTO ASA. Product names mentioned in this publication may be trademarks. They are used only for identification.

3 Pro700 Communication System Guide to Communication System Pro700 Contents General System Description... 4 Master Stations Substations Optional Equipment and Interface Units System Pro700 - Features... 1 System Pro700 Call Annunciation System... 1 General Installation Information... Installation... 4 Programming... 7 Technical Specifications... IMPORTANT INFORMATION The information in this Guide is based upon stations with REV. C or newer. These stations have Software Edition HM.X. For older versions of stations, please use the Guide A101K106/0.00 Aug Old and new versions of stations will work together with all functions they can be programmed to perform. It is important to note that if the feature SILENT ALARM is to be used on the system, all stations must have the new software. It is especially important to note that the switch-programming is different on new and old stations.

4 General System Description Pro700 is a fully electronic direct speech intercom system for handsfree, high-speed internal communication with up to 40 subscribers. The system does not utilize a central or exchange unit. Stations are microprocessor controlled, providing an extensive range of standard and optionally programmable features. Each station is individually programmable, giving full flexibility regarding features and extension numbers. The station s LCD display allows for features like caller identification and message/absence information. System Pro700 is an all-to-all system. From any master station, it gives the caller immediate connection to any other master or substation in 4 the system. The called number will be visible in the station's LCD display. System Pro700 is equipped with one conversation link. In addition, a program distribution channel for e.g. music is available. The keypad is arranged for quick and simple dialling. In the called station, the initiator s identification (extension number) is displayed. The T-button is provided for manual control of a conversation when desired, and the X-button is used to cancel a call. Either party may cancel the call. EASY INSTALLATION All stations are interconnected with a -pair installation cable in a star or loop/serial configuration using a 0.6/ 0.5mm diam. (4 AWG) cable. (NOTE: Three pairs are needed when program distribution channel is required). For easy connection of stations, various types of standard wall sockets can be used. The stations are powered from a centralized power supply (1 to 7 Volt DC/4Amp, depending on the cable distances and system size) terminated to the installation cable network. The station cord (BF type) contains 4 pairs: audio and signalling, power supply, program distribution and external loudspeaker/door opener function.

5 General System Description Up to 40 subscribers No central exchange (decentralized system) Stations with display Best price/performance on the market Simple installation (loop cabling) Handsfree operation (duplex) Easy to expand Wide range of features Typical System Pro700 users include: Small industries Small prisons Police stations Warehouses Shops/supermarkets Petrol/Gas stations Doctor offices Dentist offices Workshops Nursing homes Door and gate control Schools Private homes System Pro700, a consecutive success 14 5

6 Master Stations Pro700 stations are divided into two categories: MASTER STATIONS - make calls and receive calls from any other master station. SUBSTATIONS - receive calls and make calls to a limited number of predetermined call numbers (direct call buttons). Each master station is equipped with a standard 15-button keypad. No extra feature buttons are required. Simple push-button dialling puts all the features at the user s finger tips. To make a call, the user presses the button corresponding to the first digit of the desired extension number. Dial access is virtually instantaneous. On receiving a steady dialling tone, the user continues dialling. Call connection is indicated, in both the initiating and the receiving station, by a warning tone and a station lamp which remains lit until the call is cancelled by either party pressing X. ACCESSORIES: GF6, Wall bracket, plastic, grey. Bracket for wall-mounting of station types AA701 and AB707. BF66. Front plate, plastic, grey Clip-on plate to convert the surfacemounted stations AA70/AB708/AB709 to flush-mounted stations. Dimensions frontplate: length: 80 mm - 11" width: 140 mm - 5.5" thickness: 5 mm - 0." distance between fitting holes: 50 mm inch Dimensions wall cut out length: mm - 8.8" width: 8 mm -." depth: 51 mm -." BF94, Flush mount back box, metal. for stations AB71-F and AB71A-F. Dimensions: length: 04 mm - 8.0" width: 114 mm - 4.5" (w/lugs: 14 mm - 5.") depth: 60 mm -.4" BF65, Flush mount back box, metal. for stations AA70, AA704, AB708 and AB709. Dimensions: length: 66 mm " width: 100 mm -.9" depth: 60 mm -.4" AA701, Desk/Wall Master Station with Display Although only the size and weight of a conventional telephone handset, the AA701 combines all essential functions needed for effective internal communication: loudspeaking handsfree, softspeaking confidential and total privacy. Each station in the Pro700 system is individually programmable, providing full flexibility regarding features and extension numbers. The AA701 s display gives access to features including caller identification and message/absence information. The cabinet of the AA701 station is cast in high-grade, impact-resistant ABS plastic with a satin finish. The AA701 station is designed for desk use or wall-mounting, using a handy wallbracket GF6. Colour: grey Dimensions: depth: 64 mm -.5" width: 78 mm -.0" height: 14 mm - 8.4" Weight: 50 g AA701 AA70 AA70, Wall Master Station with Display The AA70 has the same basic features as the desk/wall master station AA701. The surface mounted station can easily be converted to a flush mounted model by use of a clip-on front plate BF66. For concrete mounting, the back box BF65 is required. The station housing is high-grade, impact resistant ABS plastic. Colour: grey Dimensions: depth: 51 mm -.0" width: 80 mm -.1" height: 0 mm - 8.7" Weight: 50 g 6

7 Master Stations AA70 AA704 AA705 AA70, Industrial Master Station The AA70 is a surface mount, splashproof station designed for humid, dirty and outdoor conditions. It has a flame and shock resistant casing of durable Bayblend plastic. The front can be removed to allow easy access during installation and service. The station has an internal Watt amplifier and the speaker volume can be adjustable with switches located inside the station. In addition to the built-in loudspeaker, the unit is prepared for connection of an external speaker. As an option, the 10 Watt power amplifier FC740 can be used with this station. If required, the FC740 also allows you to use the loudspeaker both as loudspeaker and microphone, (talkback function). The AA70 unit has a built in relay which can be used for the Remote Output/Door Opener function (caller pressing key "5") or to drive external call indicators (lamp/buzzer). Pressing key "" on the called station will cancel the warning signal. Colour: grey Dimensions: depth: 6 mm -.5" width: 14 mm - 4.9" height: 44 mm - 9.5" Weight: 845 g Ingress protection: IP64 AA704, Console Master Station The AA704 station is designed for console mounting or wall mounting using back box 600 or 600 for respectively flush and surface mounting. The keyboard folio of UV-cured PVC is resistant to numerous fluids and chemicals. The keyboard is equipped with a backlight. The light intensity can be adjusted with a variable resistor accessible at the front. The station is ideally suited as a "control desk station" for correctional institutions, prisons, police stations, marine environments and more. The station has an internal Watt amplifier and the speaker volume can be adjustable with switches located inside the station. As an option, the 10 Watt power amplifier FC740 can be used with this station. If required, the FC740 also allows you to use the loudspeaker both as loudspeaker and microphone, (talkback function). The AA704 unit has a built in relay which can be used for the Remote Output/Door Opener function (caller pressing key "5") or to drive external call indicators (lamp/buzzer). Pressing key "" on the called station will cancel the warning signal. Colour: dark grey Dimensions: depth: 50 mm -.0" width: 15 mm - 4.8" height: 80 mm " Weight: 400 g AA705, Heavy Industrial Master Station The AA705 station is a splashproof model designed for humid, dirty and outdoor conditions, and areas with extreme noise. The station is equipped with a noise cancelling microphone, has an orange Makrolon plastic housing and a membrane film keyboard. The station has an internal Watt amplifier and the speaker volume can be adjustable with switches located inside the station. The unit requires connection of an external loudspeaker. As an option, the 10 Watt power amplifier FC740 can be used with this station. If required, the FC740 also allows you to use the loudspeaker both as loudspeaker and microphone, (talkback function). The AA705 unit has a built in relay which can be used for the Remote Output/Door Opener function (caller pressing key "5") or to drive external call indicators (lamp/buzzer). Pressing key "" on the called station will cancel the warning signal. Colour: orange Dimensions: depth: 17 mm - 5.4" width: 160 mm - 6." height: 40 mm - 9.4" Weight: 1.00 kg Ingress protection: IP64 7

8 Substations AB707 AB708 AB709 AB707, Desk/Wall Substation with direct dialling buttons and Display This station is similar to the Desk/Wall Master Station AA701, but has a limited keypad. It has dial buttons which are preprogrammed to call station numbers 11, 1 and 1. When these buttons are used in combination with the X-button (X + call button), calls can be made to subscriber no. 1 (X+11), Program Distribution Channel (X+1) or subscriber no. (X+1). The station can also be programmed to dial the Emergency Call (instead of 1 and ). The station is also equipped with T, 0 and X buttons, volume up, volume down and confidential mode (handset function). Colour: grey Dimensions: height: 64 mm -.5" width: 78 mm -.0" length: 14 mm - 8.4" Weight: 50 g AB708, Wall Substation with "Doorbell" function or 1 direct dialling button The AB708 station is similar to the Wall Master Station AA70, but without display and keypad. It is designed for indoor conditions and is suitable as a door station. The station is equipped with a call button, activating the door bell function to all stations programmed as receivers of this function. Stations receiving the distinctive door bell chime pattern can reply to the door call by dialling "5". A normal two way connection is then established. Programming the station will allow two more direct dialling possibilities: - to subscriber no. 1 (a time limit can be programmed, the call will cancel after 0 seconds) or - activate the Emergency Call feature. The surface mounted station can easily be converted to a flush mounted model by using the clip-on front plate BF 66. For concrete mounting, the back box BF65 is required. Colour: grey Dimensions: depth: 51 mm -.0" width: 80 mm -.1" height: 0 mm - 8.7" Weight: 50 g AB709, Wall Substation with direct dialling butons The AB709 station is similar to the Wall Master Station AA70, but without display. It is designed for indoor conditions and is suitable as a door station. The keypad has dial buttons which are preprogrammed to call station numbers 11, 1 and 1. When these buttons are used in combination with the X-button (X + call button), calls can be made to subscriber no. 1 (X+11), Program Distribution Channel (X+1) or subscriber no. (X+1). The station can also be programmed to dial the Emergency Call (instead of 1 and ). The surface mounted station can easily be converted to a flush mounted model by use of the clip-on front plate BF66. For concrete mounting, back box BF65 is required. Colour: grey Dimensions: depth: 51 mm -.0" width: 80 mm -.1" height: 0 mm - 8.7" Weight: 50 g 8

9 Substations AB71-F AB71A-F AB71 AB71A BC75 AB71, AB71-F, Tamper resistant substation. These stations are compact, dust resistant units with a very robust construction. The stations are made of aluminium with a stainless steel frontplate (AA71:.0 mm/ab71-f:.0 mm). The construction ensures optimal protection of the push-button, microphone and loudspeaker. The stations are ideally suited for applications in correctional institutions, prisons, police stations, parking garages, subway stations and more. The AB71-F is for flush mounting and comes with a light backbox for EMC protection. When an optional backbox is needed for concrete mounting, the unit BF94 must be ordered. The stations have internal loudspeakers with Watt amplifiers. An external speaker can easily be connected. The stations are equipped with a call button for establishing connection to: - extension number 1 or - "Doorbell" function or - CAS Call-in function or - Emergency Call By installing the optional Sound Detection Module DP996, a call can be initiated automatically when a certain preset sound level is reached. The stations have built in relays for the Remote Output/Door Opener function. Dimensions: See AB71A and AB71A-F AB71A, AB71A-F, Door Station These door/vandal proof stations are compact, dust resistant with a very robust construction. The stations are made of aluminium with a 1.5 mm thick stainless steel front-plate. The construction ensures optimal protection of the push-button, microphone and loudspeaker. The stations are ideally suited for applications in corridors, car parks, subway stations and more. The AB71A-F is for flush mounting and comes with a light backbox for EMC protection. When an optional backbox is needed for concrete mounting, the unit BF94 must be ordered. The stations have internal loudspeakers with Watt amplifiers. An external speaker can easily be connected. The stations are equipped with a call button for establishing connection to: - extension number 1 or - "Doorbell" function or - CAS Call-in function or - Emergency Call By installing the optional Sound Detection Module DP996, a call can be initiated automatically when a certain preset sound level is reached. The stations have built in relays for the Remote Output/Door Opener function (caller pressing key "5") Dimensions: AB71A AB71A-F depth: 65 mm 60 mm width: 90 mm 10 mm height: 180 mm 0 mm Weight: 1.5 kg 0.9 kg BC75, Multipurpose Substation This is a multipurpose substation in a splashproof housing designed for humid, dirty and outdoor conditions. It consists of a flame and chip resistant casing of durable Bayblend plastic. The front can be removed to allow easy access during installation and service The unit has neither loudspeaker nor microphone. Two external speakers must be added, alternatively, a separate dynamic microphone may be connected. The station has an internal Watt amplifier and the speaker volume can be adjustable with switches located inside the station. As an option, the 10 Watt power amplifier FC740 can be used with this station. If required, the FC740 also allows you to use the loudspeaker both as loudspeaker and microphone, (talkback function). The BC75 unit has a built in relay which can be used for the Remote Output/Door Opener function (caller pressing key "5") or to drive external call indicators (lamp/buzzer). Colour: grey Dimensions: depth: 6 mm -.5" width: 14 mm - 4.9" height: 44 mm - 9.5" Weight: 750 g Ingress protection: IP64 9

10 Optional Equipment and Interface Units GD745 GH750 HD751 GD745, Handset module The GD745 Handset Module can be connected to the following Pro700 stations: AA70, AA704, AA705 and BC75. The handset is equipped with a cradle switch and a press-to-talk button for simplex function. Colour: black Dimensions: Bracket: Length: 04 mm Width: 66 mm Depth: 54 mm Handset: Length: 45 mm Width: 59 mm Depth: 54 mm Weight, total 500 gr. GH750, Multipurpose Relay Unit- CCTV Camera switch/audio recording The GH750 unit is equipped with 8 relays. When a door station (extension number 1-8) activates the "doorbell" function, one or several relays in the GH750 can operate and control CCTV cameras. The relay(s) is active until the call is answered and cancelled. An autoscan function can be activated by an external closing contact, which will step the relays in sequence. The number of relays in the scanning sequence can be from to 8, and the autoscan time interval can be set to 8 or 16 seconds. The GH750 unit can also be individually programmed to operate when a predeterminated extension number is called. If required, such call can be audio recorded. The unit supervises the Pro700 line and operates the relay(s) when the right combination of calling and called extension number occur. GH750 can also be programmed to operate on any specific station number. This way the unit operates as a remote control unit in which one or several relays can be operated. Colour/Dimensions: Same as HD751 HD751, Autodialler with chime and alarm signal for evacuation, burglary alarms, school signal. The HD751 unit is equipped with 4 alarm inputs for activation of auto dial function to All- and Group Call. Closing contacts will activate the calls. Alarm input 1: Activates All Call and gives a 1000 Hz tone, on/off 800 ms, (evacuation alarm) during the call. Alarm input : Activates All Call and gives a 1000 Hz tone, on/off 100 ms, ( burglary alarm) during the call. Alarm input : Activates Group Call # 1 and gives one chime signal (gong), ( school signal ). Alarm input 4: Activates Group Call # and gives one chime signal (gong), (school signal). Optional Stored Voice Module HD75. This plug-in module has an alarm input for activation of a stored voice message of up to 60 seconds length. This information is broadcast as an All Call message. The message is recorded by use of a standard master station. Colour: grey Dimensions: length: 0 mm - 8.6" width: 145 mm - 5.6" height: 65 mm -.6" Weight: 50 g 10

11 Optional Equipment and Interface Units HD75 HD75, Audio Interface - PA Interface/Radio Interface The HD75 is a general interface for interconnection of Pro700 to various external audio sources like public address systems, closed radio networks, alarm systems and more. The unit has one input (RX) for receiving and one for transmitting (TX). Built-in relays control the KEY and ON functions. In addition, an All Call can be activated by an external closing contact, using an external audio source as input. Colour: grey Dimensions: length: 0 mm - 8.6" width: 145 mm - 5.6" height: 65 mm -.6" Weight: 50 g HD754 HD754, Telephone Interface HD754 is an analogue interface unit which interconnects a Stento Pro700 system and public telephone line or PABX. The unit permits calling in both directions in the following ways: outgoing calls; a preprogrammed number on the telephone network. incoming calls: a preprogrammed number in the Pro700 system (call number 1 or the door bell function) or selective dialling (any number) in the Pro700 system. As a programming option to incoming calls, a 4-digit password code must be entered before access is given to the Pro700 system. When the telephone call is established, this allows for a loudspeaking handsfree conversation in the Pro700 system. The unit is delivered as a compact, closed, plastic cabinet which can be placed on a shelf. HD754 is connected to the Pro700 system like a normal station with 4 wires to the network bus. A call number must be dedicated to the interface unit Colour: grey Dimensions: length: 40 mm - 9.4" width: 160 mm - 6." height: 60 mm -." Weight: 50 g Station Kits BD70 and BD70 Two station kits are available for local production of Pro700 stations. Frequently, the station design has to be adapted to meet local requirements such as measurements, housing design, etc. These kits consist of all electronic parts needed to build up a working Master and/or Substation. All mechanical parts such as housing, front plate, button(s) must be supplied locally. Detailed assembling diagrams are included. Kit BD70. Two printed circuit boards are included; NFE185A and NFE189. These PCB s are used in the tamper resistant stations AB71/AB71-F and door stations AB71A/AB71A-F. See description of these stations for station kit functionality. Kit BD70. One printed circuit board is included, NFE180. This PCB is used in the stations AA70, AA704, AA705 and BC75. See description of these stations for station kit functionality. FC740, 10 Watt Amplifier w/talkback function. FC740 is a 10W amplifier unit for use with the Pro700 stations AA70, AA704, AA705 and BC75.The unit can be used as an amplifier with talkback function or as a plain amplifier. It contains a printed circuit board NFE18, a piggy-back card for mounting on top of the station pcb NFE180. DP996, Sound Detection Module This module is designed to be mounted inside any of the following stations; AB71, AB71-F, AB71A and AB71A-F. The circuit on the Sound Detection Module will detect voice, screams or audible noise and then output an alarm signal. The card is flexible in that it can be configured by the installation contractor to fit the particular application. How strong and how long an audio signal must be present to activate the alarm output is user selectable. 11

12 System Pro700 Features Excellent sound reproduction LED indicator 1. Blank: link free. Red: busy link. Green: station in conversation 4. Green flashing: call reply 5. Orange: privacy or absence LCD display, 8 digits Key for softspeaking confidential use Volume control, volume up/down Standard international keypad for digit dialling X-key for cancelling calls Microphone cutout T-key for manual control of speech direction (simplex) Sensitive microphone The keypad provides the following features: Subscriber call numbers. 5 - Door opening feature (only from predetermined stations). 5 - Reply-back on "Doorbell" function. 6 - Last number redial/ Activating Silent Alarm 7 - Activate all-call 8 - Activate/reply on call-back. 8 - Reply back on all/group call 9 - Activating Emergency Call 91- Activate group-call no Activate group-call no. 9- Activate call reply. 96- Access the program distribution channel (music). 97+up to 4 digits. Storage of absence/message information. 97X-To delete absence/message info. 98+call number+volume - activate remote program distribution 99- Activate/deactivate the privacy function. 0 - Accept a call when the station is in privacy mode. 0 - Priority - gives predetermined stations access to the busy link. 0 - Microphone cutout. 0 - Hurry up. 0 - Call last caller. System Features: - Loudspeaking/Handsfree - Confidential - Privacy - Microphone cutout - T-button for manual control of the speech direction - Camp on busy/queue feature - Call-back - Hurry up - Absence registration - Display information - Call reply - Last number redial - Call last caller - All call (with reply back) - Group calls (with reply back) - Priority - Always privacy - Paging - Door opening - Program distribution (music) - External loudspeaker - Emergency call - Silent alarm - Remote program distribution - Direct Dial 10 key station - Direct Dial key station System Pro700 "Call Annunciation System" Feature for Door/Tamper Resistant Stations AB71, AB71-F, AB71A and AB71A-F. 1

13 Features Loudspeaking Confidential Camp on to a busy channel/station In idle, the station s extension number is shown in the LCD display. Initiator (caller) presses first digit (buttons 1-4), gets dialtone - presses second digit (0-9). The dialled extension number is displayed. The LED lights green. Calltone (approx. 1 sec.) is heard at both stations and the conversation can start handsfree, - from anywhere in either room (duplex). On the called station, the initiator s identification (extension number) is displayed. The station has a 16 step volume control. Press the + key to increase, and the - key to decrease the output volume. Station #16 in idle, the display shows: 16 LED is blank.. Station #16 dials station #. Call established, the display shows connected party #: LED is green. At any time during a call, either one or both parties can press the handset key on their station (AA701) and, using the set in the same way as a telephone handset, carry on a confidential conversation. When both parties use their stations in this mode, the system operates in open duplex. In other words, both parties are able to speak and listen simultaneously as in a conventional telephone conversation. Pressing the handset key again, it automatically reverts to normal handsfree use. Either party can press the X- button to cancel the call. Station #16 connected to station #. Station #16 in Confidential mode, the display shows: LED is green. Busy conversation channel is indicated by a red lamp (LED) in all idle stations. A caller can dial an extension number even if the channel is busy. The busy signal is heard. If the channel becomes free within a period of 10 seconds, the caller will automatically be connected. Dialling a station which is busy is indicated in the initiating station by a flashing green light. Station #16 dials station #, gets busy signal, and the display shows Camp On status: LED is red. 1

14 Features Microphone cutout Optional manual speech control Privacy To temporarily disconnect the microphone during a conversation, the 0- button may be pressed and held down. Releasing the 0-button, the conversation can continue. Station #16 connected to station #. Station #16 activates Microphone Cutout function, the display shows: 0 LED is green. All calls will be in handsfree mode until the T-button (Talk) is pressed. When calling to or from exceptionally noisy areas, manual control (T-button) of the speech direction may be used. Either party may use this function at any time during a call and revert to handsfree mode by quickly pressing the station s T-button. If both use T- button, the last one to use T has speech control. The privacy feature is activated by dialling the code 99. The station lamp (LED) will clearly show an orange light. A station in privacy is only blocked for incoming calls, so there is no need to reset the privacy function to make outgoing calls. The caller will hear a continuous, warbling tone, which indicates that the called extension is put in privacy. In the LCD display, 4 dashes ( ) will be visible. A short warning tone is heard and the green lamp flashes in the receiving privacy station. The call can be accepted by pressing the 0-button. When the call is cancelled the station reverts to privacy. The privacy function is deactivated by dialling the code 99. Station #16 is put in Privacy mode, display shows: LED is orange. Station # dials station #16, the display in station # shows: LED is flashing green. In station #16, the display shows: LED is flashing green. 14

15 Features Call back Hurry up Display information If the conversation channel is busy when making a call (red lamp in station), the caller may press the 8- button for automatic call-back. The requested call is stored in the station s memory. When the conversation channel is free, the caller is notified by a special tone signal. If desired, the connection is made by pressing "8" within 10 seconds. If not, the feature is auto-cancelled (no connection) after 10 seconds. The call-back mode is cancelled by dialling X. Station #16 dials station #, gets busy signal, and puts station in Call Back mode. The display shows: 8 LED is red. Station # becomes free, tone signal is heard. The display in station #16 shows: LED is flashing green. Press #8 for connection. If the conversation channel is busy when making a call (red lamp in station), the caller may press the 0- button within 10 seconds. The hurry up tone is heard in both busy stations. If the connection is cancelled within 10 seconds the initiator is connected to the called extension. All stations have access to hurry up, except priority stations, which can cancel the ongoing conversation and set up their own. The stations AA701, AA70 and AB707 have an 8-digit LCDdisplay. The following features are available: 1. In idle, the station s extension number is displayed. 16. When dialling, the called station s extension number is displayed.. When receiving a call, the calling station s call number is displayed. 4. Calling a station in privacy, 4 dashes ( ) are displayed. Station with the privacy function activated will also have 4 dashes displayed Calling a station with absence registration, the date or time for return is displayed (4 digits) Listening to the program distribution channel, digit 96 will be displayed When all-call (7) or group-call (91or 9) is initiated, a 60 seconds message time will count down in the display

16 Features Absence registration Call reply Last number redial To activate the absence registration feature, the user dials the code 97. Four additional digits must be entered, indicating date or time (or any other type of message). This 4-digit message will be visible in the station s LCD display and the station lamp will emit an orange light. Calling this station, the initiator will hear a specific tone and read the 4- digit absence message in the display. To establish a connection, the caller can dial 0, or after 10 seconds the call will automatically be established. The code 97X is used to cancel an absence registration. Station #16 dials for absence registration, "back half past 4". The display shows: LED is orange. Station # dials station #16, the display in station # shows: LED is flashing green. To make a call when the called person is absent, the caller may dial the code 9, to indicate call back. The call is auto-cancelled. In the dialled station the station lamp will flash green and the display will show the initiator s extension number. Any initiator can leave such a message in several stations and each station can have up to 4 callreply requests in queue. When the called subscriber returns, and sees the green flashing lamp, he can dial the number visible in the display (or code 9 ), and automatically be connected to the caller. If the station lamp continues to flash after cancelling, there is another call-reply in queue. NOTE: The call-reply requests should be attended to first. If the called subscriber dials another number, program distribution feature or X, before answering the Call Reply, the feature will be cancelled and will not reappear. Station #16 connected to station #, but no answer. Station #16 activates Call Reply function. The display in station # shows: 16 LED is flashing green. A subscriber can initiate Last Number Redial by dialling digit 6. This feature is restricted to ordinary calls only, (will not redial all/group calls). Stations programmed to activate Silent Alarm cannot utilize the "Last Number Redial" feature. Call last caller Any subscriber can re-establish a connection to the last caller (last incoming call) by dialling digit 0. 16

17 Features All call (with reply back) Group call (with reply back) Emergency call Any user can initiate an all call, by pressing 7. A distinctive tonesequence announces the all-call both to the initiator and to all stations, except those who have been eliminated as all-call receivers ( programmed with switches in each individual station). Pressing and holding the T-button, the initiator can broadcast a verbal message and press X to cancel. The maximum all-call duration is 60 seconds. Making an all-call, the count down will be indicated in the display, from 60 to 00, (second by second). With reply-back on all-call, the initiator announces the required person or persons and presses the 8-button or let the call stay until auto-cancel after 60 seconds. The called person(s) answer by dialling "8" on any station receiving the call, (no time limit). Station #16 dials ALL Call, the display shows: 7 60 LED is green. System Pro700 provides for two group-calls with optional answer-back feature. The members of group 1 and group are programmable with switches inside each station. The groups may overlap. Any user can initiate a group-call by dialling 91 (group no. 1) or 9 (group no. ). A distinctive tone-sequence announces the group call both to the initiator and to all stations programmed as groupcall receivers. Pressing and holding the T-button down, the initiator broadcasts a verbal message and presses "X" to cancel. The maximum group-call duration is 60 seconds. Making a group call, the count down will be indicated in the display, from 60 to 00, (second by second). With reply-back on group-call the initiator announces the required person or persons and presses the 8-button or let the call stay until auto-cancel after 60 seconds. The called person(s) answer by dialling "8" on any station receiving the call, (no time limit). Station #16 dials Group Call no. 1, the display shows: LED is green. Stations with the «9»-key, both master- and substations, can be programmed to activate Emergency Call. By pressing and holding the «9»- key, an important message can be given to the group of stations that are programmed as receivers in Group Call no. 1. By releasing the «9»-key, the call is automatically cancelled. The Emergency Call has priority over all other calls except the Silent Alarm feature. 17

18 Features Priority Always Privacy "Doorbell" function Any preprogrammed station may have the priority feature. If the priority station dials a extension number while the conversation channel is busy (or receives privacy-signal), he has the option to press 0 to override the busy link and be connected to the called party, (i.e. any ongoing call is automatically cancelled). The cancelled conversation is not restored. If the priority caller does not wish to use the priority function, X is used to cancel the call. The priority function will also cancel All- and Group-calls 18 The Always Privacy feature is activated by switch programming. The station lamp (LED) will clearly show an orange light. A station in Always Privacy is only blocked for incoming calls (not for All and Group calls), outgoing calls are initiated the normal way. When a call is made to a station programmed for Always Privacy, both caller and called extension will hear a continuous ringing tone. The ringing tone in the called extension is automatically raised to the maximum audio level, and will continue to ring for minutes or until the call is accepted by pressing the 0-button or cancelled by the initiator with the X-button. The LCD display shows 4 dashes ( ) and the green lamp flashes. When the call is cancelled, the station goes back to privacy condition. Station #16 is put in Always Privacy mode, display shows: Station # dials station #16, the display in station # shows: LED is flashing green. In station #16, the display shows: LED is flashing green. This feature is only valid for substations AB708, AB71, AB71-F, AB71A and AB71A-F where the call button activates the Doorbell function. A distinctive tone-sequence is heard in the door station and in all the stations receiving the doorbell call. Any master station receiving the doorbell call can now call back to the door station by pressing 5 and a normal audio connection is established. If the "doorbell" call is not answered within 0 seconds (alternatively minutes), the call request is canceled. The system allows for two different tone signals, i.e. the front-door signal can be different from the back-door signal. This is switch programmed inside the door station, the door stations are assigned different tone IDs. Any station can be individually programmed to receive a call from a "doorbell station", either to receive calls from door stations with tone ID no. 1 or ID no. or from both. For the receiver of the "doorbell" call to activate the Remote Output/Door Opener function in the door station, press and hold the digit "5". The stations AB71, AB71-F, AB71A and AB71A-F have built in relays for this function. These stations also have a separate Local Output function for controlling of cameras, lamps, etc., e.g. lamp warning to be installed inside the door. Both this warning and the call can be cancelled by pressing a button connected to the Local Reset function.

19 Features Program distribution Remote program distribution Remote Output/ Door opener This feature requires one extra pair in the installation cable, giving a total of pairs. To this extra pair, a program source is connected, e.g. music. All master stations may use this feature, by dialling "96", and be connected to the Program Distribution channel. There is no need to cancel the program distribution feature (music) to make outgoing calls. The music is put on hold during the call, which is the same for incoming calls. Cancelling the call, the music is automatically reconnected. To cancel the Program Distribution feature, dial X. This feature requires one extra pair in the installation cable, giving a total of pairs. To this extra pair, a program source is connected, f.ex. music. The feature allows a master station (stations with a complete keypad) to connect Program Distribution to other stations, e.g. substations without any keypad. To put Program Distribution in the loudspeaker in the waiting room of a medical centre, the master station dials 98 + substation number + required sound level (1-). To cancel the feature, the master station dials 98 + substation number + 0 and the Program Distribution to that specific substation is disconnected. A normal call to the substation with Program Distribution will mute the Program Distribution during conversation, but will automatically return when the call is cancelled. NOTE: By dialling from the master station, all receivers of Program Distribution will be disconnected. The stations AA70, AA704, AA705, AB71, AB71-F, AB71A and AB71A-F are equipped with an internal relay which can be used to control an electrical door lock or similar. The stations AA701, AA70, AB707, AB708 and AB709 must use an external relay which is controlled by an internal transistor output. The output in the called station can only be activated by the initiating party by keeping the key 5 down. During this period a normal conversation can take place. To activate this function the initiating station must be programmed with Priority. The called station, where the relay is connected, must also be programmed. See Programming chapter. A station AA701, AA70, AB707, AB708 or AB709 programmed for Remote Output/Door Opener can not be connected to an external loudspeaker. 19

20 Features Silent Alarm External loudspeaker Direct dial 10 key stations Specially programmed master stations can dial «6» in an emergency situation to make a call to a predetermined group of stations. (The call can be initiated by a concealed button or a foot-pedal). Some stations can be pre-programmed to receive a call in an emergency. This feature is specially designed for social security offices and police interrogation rooms where emergency situations might occur. The station making the call will remain silent, meaning no warning tone and no light in the station s lamp. In the receiving stations a special warning tone is heard and the stations lamps blink red. By dialling 6, any receiving station can listen to the emergency situation, again without any warning. The station lamp(s) of those who listen (1 or more stations at the same time) will blink green. When a receiving station dials 6 the second time, a normal duplex conversation is established with normal warning tones. All other stations will then have a red light indicating busy channel. By dialling X instead of 6 the second time, the call will return to alarm-call and an emergency warning tone will continue in all receiving stations. Stations that do not want to receive the emergency warning tone can dial X, thereby stopping the alarm signal. 0 An external loudspeaker can be connected to any station to increase the audio output power. The loudspeaker s impedance must not be less than 0 ohm. In the station, where the loudspeaker is connected, switch or jumper programming is necessary. See Programming chapter. Stations AA701, AA70, AB707, AB708 and AB709 connected to an external loudspeaker, can not operate the Remote Output/ Door Opener function. Individually programmable on any master stations, the keypad can be changed from a normal keypad with - digit dialling to a keypad for 1-digit direct call to 10 subscribers. You can choose between the following numberseries for the 10 direct dial keys: - 10, 11, or 0, 1,... 9 or 0, 1,...9 or 40, 41, As a programmable feature, the feature Emergency Call is available on key "9". Direct dial key stations The substations AB707 and AB709 have buttons for direct call to subscriber numbers 11, 1 and 1. In combination with the X-button (call button + X-button) you get access to subscriber number 1, Program Distribution and number. Instead of subscriber numbers 1 and, the button can be programmed to activate Emergency Call. The substations AB71, AB71-F, AB71A and AB71A-F can call subscriber number 1. They can also be programmed to activate the Doorbell, CAS-Operator or Emergency Call feature.

21 Pro700 Call Annunciation System (CAS) The Pro700 System can be programmed to operate with the feature Call Annunciation System (CAS). This gives the possibility of simultaneously queuing calls from up to 9 stations to up to CAS Operator Stations (guard stations). The CAS call-in stations are normally door/tamper resistant substations such as: AB71, AB71-F, AB71A or AB71A-F. The CAS operator stations are normally master stations AA701 or AA70. All stations installed in a CAS system MUST be switch programmed to enable the CAS feature. Stations not programmed will operate with ordinary Pro700 features. For system layout, please see drawing below. OPERATION: (CAS call-in station). A CAS call-in station can make a call request to the CAS operator in the following ways: - press the CALL button (or button "9" on a master station, if a master station is used as a CAS call-in station) - activate the Remote Input function - automatic activation of the Sound Detection Module DP996 (audio level detection). This module is optional and must be installed separately. The station's LED will flash green and a short tone is heard, or alternatively a message is received from the Program distrubution channel. The Local Output function switches on a warning light (if installed), for instance in the corridor. In idle the CAS operator stations (max ) will all display their own extension number: CASOP-15 OPERATION: (CAS operator station). The call request will be presented with a call tone and a flashing green LED. The tone can be heard once or repeated every third second (programmable). The CAS operator's station display will show: - the first caller in queue (16) - queue index no. (1) - nos. of calls in queue (5) The call can now be accepted on any of the CAS operator stations. The operator has the following options: 1 press the "0" button to accept the call (accepting the first caller in queue visible in the display). A communication path is established. The accepted CAS call-in station is displayed together with the updated nos. of calls in queue. The station LED will go steady green Optional programmable scroll features: press the "T" button to scroll the queue. Use the "0" button to accept the displayed extension number. press the "X" button to move a CAS request to the back of the queue. Up to 9 CAS call-in stations can be queued simultaneously. The CAS call-in station also has a local reset function, which gives the CAS operator (guard) the possibility to cancel the CAS request locally from an 1

22 Pro700 Call Annunciation System (CAS) external button adjacent to the CAS call-in station. When a CAS request is accepted, the stations' LED goes steady green and the established communication operates in simplex mode (the operator hears the audio from the CAS call-in station - listen mode). To control the speech direction, the T-button must be used (push T-button to talk, release to listen). An established CAS call can only be overridden by a priority call, not by an ordinary call or by all- or group call. The Sound Detection Module DP996 can be installed in the stations AB71, AB71-F, AB71A, and AB71A-F, and can activate a CAS request when the ambient noise/voice is above a preprogrammed level. If the CAS operator wants to remotely control an activity by the CAS call-in station, the "Remote Output/Door Opener" feature is used. Button "5" on the keypad must be held down to activate the remote output. ADDITIONAL CAS OPERATOR FUNCTIONS: Audio Monitoring The CAS operator has the possibility to listen in to the CAS call-in station without giving warning tone or light. Dial feature code "95" plus the required extension number (10-49). This feature is switch programmable in the CAS callin station (enable/disable). The CAS operator's display shows the number of the called station. The LED is flashing orange. 16 The CAS operator can dial "95" plus "5" to start audio monitoring of all stations, enabled for the feature, in the system. Each station will be connected for 5 seconds. The CAS operator's display shows: - connected station (1) - queue index no. (1) - nos. of stations to be monitored (6), programmed stations The CAS operator dials "95" plus "6" to start audio monitoring of all stations in the system, starting with the first station and advancing to the next station by pressing the "T" button. Pressing button "0" will establish a call to the monitored station. After monitoring the last station the audio monitoring sequence is terminated. The monitoring sequence can also be terminated by pressing the "X" button. The CAS operator dials "95" plus "7" to have the same operation as "95" + "6" above, but the audio monitoring will continue for three sequences or be terminated when a call is established or button "X" is pressed. Remote Program Distribution: After a CAS operator has accepted a call with the "0" button, pressing button "98" plus "1", "" or "" will connect the caller to the program distribution channel with audio level low, middle or high. Reconnecting the same CAS caller and pressing "98" plus "0" will disconnect the channel again. To cancel all stations connected to the program distribution channel, dial "98" plus "0". Anti Harassment Function: After a CAS operator has accepted a call with "0", pressing button "7" will activate the Anti Pester Function for that called CAS call-in station. The connection will be cancelled, and that station may not initiate any calls for the next 15 minutes. Remote Dial: In idle, the CAS operator can establish a call between two CAS call-in stations. Pressing the code "94" plus "call no A" plus "call no. B" will establish a connection between CAS call-in station A and B. To cancel the call, the Operator can dial 94 plus X. The call can also be cancelled from station A or B by pressing the CALL button. Delayed CAS Call If required, a CAS call-in station can be programmed to have a Delayed Call function. The Call button must be pressed and held for a minimum of seconds to activate a call. This for security reasons, for instance in lift/ elevators. Note: By special switch programming in the stations, also the Master Stations AA701, AA70, AA70, AA704, AA705 as well as substations AB707, AB708 and AB709 can also operate as CAS call-in stations.

23 General Installation Information For proper installation of the intercom System Pro700, the following equipment is required: A. Stations Up to 40 stations can be connected in a system. A maximum of 16-0 is recommended. Master stations: AA701, AA70, AA70, AA704 and AA705. Substations: AB707, AB708, AB709, AB71, AB71-F, AB71A, AB71A-F og BC75. B. Station cords Various station cords are available for connecting of the station AA701 and AB707 to the cable network (wall socket). All other stations are connected with screw terminals inside the station. C. Wall sockets Modular jack assembly, for termination of the station AA701and AB707 to the installation cable. The following sockets are available: - KB171, surface mounting, - KB17, flush mounting. D. Power supply The power supply output voltage should be between 1 and 7 Volt DC. All stations are connected to this power unit via the installation cable, using the parallel wiring principle. The capacity of the power (Amp) depends on the system size. The following power supplies are available: - LA617, 0VAC/18VDC,1A - LA617A, 115VAC/18VDC, 1A - LA618, 0VAC/18VDC, 4 A - LA618A, 115VAC/18VDC, 4 A - LA95, 0VAC/7VDC, 5A - LA94A, 115VAC,4VDC, 5A The LA617/LA617A (1A) unit should be used in systems with max. 5 stations. The LA618/LA618A (4A) should be used in systems with max. 0 stations. They are adjustable between 1,5 and 18VDC output. LA95/LA94A (4VDC) should be used in systems with long cable runs to stations, max. 5 stations. This power supply is delivered with an output voltage of 7 Volt DC. The stations can be cabled to the power unit in star or loop configuration, or a combination of both. If a standard telephone cable quality (0,6mm/4 AWG) is used, the maximum distance from any station to a power unit is: - 1 V DC, 100 meters (00 ft.), - 18 V DC, 00 meters (1000 ft.), - 4 V DC, 500 meters (1600 ft.) A system can be powered with more than one unit, to give a decentralized solution for large installations. E. Battery backup Either a 1 or 4 Volt battery can be used as an emergency backup power unit. By adjusting the power supply LA618/LA618A to 1,5 Volt or LA95 to 7, Volt these units will function as trickle chargers. F. Installation cable pairs (4-wires), 0.5 or 0.6 mm. diam. (4 AWG) twisted telephone cable. -pairs must be used when the feature Program Distribution (Music) is required. If the cable to one or several stations passes close to radio aerials or other interference sources, the entire installation cable must be screened type (each individual pair). Due to data transmission on the cable network between stations, a cable of good quality should be used (low capacitance). G. Maximum cable length The maximum total cable run in a system, (max. capacitance 87 nf): - cable with 10 nf/km (standard quality) max. 700m, (100 ft). - cable with 47 nf/km (good quality) max. 1700m, (5100ft). H. Tools Ordinary installation tools. The Parallel Wiring Principle of System Pro700 STAR CONFIGURATION POWER SUPPLY 1-7 VOLT DC STATIONS STATION CORD WALL SOCKET LOOP CONFIGURATION POWER SUPPLY 1-7 VOLT DC NOTE: The stations in the Pro700 system are NOT compatible with Ring- Master CB600 stations. INSTALLATION CABLE, 0.5/0.6 MM. DIAM.