2 $POUFOUT

Transcription

1

2 2

3 3 Insta The company 4 Tronic Trafo Controls Instafunk Appendix 46

4 4 Insta is an innovative, medium-sized company, part of a group of companies of building installation technology with focus on development and fabrication of products for building systems engineering and lighting technology. 1 Building system engineering 2 Lightment LED luminaires and controls Installation technology / sensors Installations technology / actuators Bus systems, flush-mounted Bus systems, REG LED project business Architectural lighting Advice / realization / special luminaires LED luminaires Interior and exterior lighting Controls UNIVERS, DALI, KNX, 1-10 V, LEDTRIX, DMX

5 5 For further information please order our brochure»insta The company«at Insta Elektro GmbH. founded in 1970 by three well-known manufacturers of electronic installation appliances: Berker, Gebr. Berker GmbH & Co, Schalksmühle; Gira, Giersiepen GmbH & Co. KG, Radevormwald and Jung, Albrecht Jung GmbH & Co. KG, Schalksmühle. Headquarters: Lüdenscheid, Germany. Insta s 100% subsidiary: ELKA-Elektronik GmbH, Lüdenscheid. Product range: building automation, LED lighting, lighting control. 500 employees. Yearly turnover: approx. 70 million Euro

6 zwe 6

7 7 Accessories SNT W page 10 SNTF 105 / SR W page 15 6-fold distributor page 19 SND 40 / Potitransformer W page 10 SNTF 105 / LI W page 16 Overvoltage protection module page 20 SNT 70 / QU W page 11 SNTF 105 / SR W page 16 EMC module 0.31 A page 20 SND 70 / QU Potitrans former W page 11 SNTF 105 / SR W page 17 SNTF 70 / SR W page 12 SNT 105 / 1-10 V page 17 SND 105 / Potitransformer W page 12 SNT 150 / SR W page 18 SNT 105 / SR W with strain relief page 13 SNT 200 / SR W page 18 SNT 105 / SR W without strain relief page 13 ST 105 / W page 19 SNT 105 / ZY W page 14 SND 105 / ZY W with potentiometer page 14 SNTI 105 / SR W page 15

8 8 y x x Insta offers a range of electronic transformers in many sizes to suit the needs of a spectrum of applications like architecture illumination, medical technology, furniture industry and illuminated advertising. Insta Tronic transformers stand out due to their high quality workmanship, wide load range of W, electronic short circuit protection, temperature protection with automatic power reduction. Fields of use Luminaires with low-voltage halogen lamps are designed for a power consumption of 5 W to 100 W and an operation voltage of 12 V. Thus a transformer must convert the mains voltage of 230 V into an alternating voltage of 12 V. Here Insta offers a wide range of electronic transformers (also called converter or switched-mode power supply) under the name Tronic Trafo. To compensate mains voltage fluctuations, electronic transformers are designed for a secondary nominal voltage of 11.7 V. Thus, even in case of mains voltage and load fluctuations a lamp voltage of 12 V is not exceeded. Electronic short circuit protection If the current which is taken from the transformer exceeds a limit value, a protection switch blocks the function much faster than a fuse and thus prevents further current output of the transformer. When the fault in the system has been removed, the transformer automatically restarts its normal operation. Electronic over-temperature protection A Tronic transformer is capable of protecting the circuit if the temperature or loading is exceeded. This protects the system integrity and avoids defects. If the Tronic transformer is over-loaded, it cannot dissipate the generated heat because of unfavourable fitting conditions or it is heated up by the connected lamps, the temperature in the transformer rises too high. Such a high temperature would shorten the service life of the transformer. Therefore a protection circuit measures the temperature of the transformer. If the limit temperature is exceeded, it automatically dims down the connected lamps. Thus overhea ting and defects to the devices can be avoided. If an automatic dimming of the lamps is no ticed, cooler operating conditions for the transformer should be provided in the long run. By measuring the temperature of the tc-point marked in black on the labelling of the trans former, the faultless operation of the Tronic transformer with regard to overheating can be checked. If, after operation over several hours, the temperature stays below the admissible printed value, the device is fitted perfectly. Tested quality Insta Tronic transformers bear the test and safety marks of many European countries. This guarantees the user a widely acknowledged quality of the product. Fitting conditions Since the Tronic transformers of Insta bear the MM mark, it is admissible to install them into furniture without knowing the grade of fire resistance of the furniture material. A minimum space, however, depending on the type of the device and indicated in the fitting instructions, must be provided around the transformer.

9 9 Operating conditions for Tronic transformers The following installation rules should be observed by users of Tronic transformers in order to guarantee technically faultless operation. Length of the secondary lead must not exceed 2 m The secondary lead must not be laid parallel to mains leads in order to prevent radio interferences For installation in lights please check the temperature at the tc-point Provide for sufficient space between lamp and transformer so that the connected lamps cannot heat up the transformer Do not switch Tronic transformers together with inductive loads (e.g. fluorescent lamps with conventional ballasts), as otherwise spikes could damage the transformers If the 230 V mains is troubled with spikes, over-voltage protection modules have to be installed If Tronic transformers are fitted in lights of protection class I, an exceeding of the radio interference limit values can be compensated by installation of an EMC-module For dimming of Tronic transformers only use Tronic dimmers of universal dimmers of the companies Insta, Berker, GIRA or Jung or dimmers of other manufacturers switching off permanently after a short-circuit Additional product-specific installation rules that are attached to the transformers must strictly be observed

10 10 Tronic Trafo SNT W SND 40 / Poti-Trafo W Art.-no V Art.-no Discontinued item, only small quantities available. Design version Rated output voltage Mains current (40 W) Power factor flexible connection cables AC 240 V ~ W 11.7 V 0.18 A 0.96 c Efficiency 95 % Housing temperature t c Secondary line min mm 2 Short-circuit protection Overload / Temp. protection No load Softstart Fire protection Safety class Dimmable Marks of conformity max. +50 C at maximum load max. +85 C at maximum load electronic switch-off, automatic restart automatic power reduction protected lamp-saving starting switch-off in case of fault II with Tronic dimmer and universal dimmer MM, ENEC, VDE, VDE-EMV 73 x 35.5 x 18 mm This mini Tronic transformer offers the lamp designer many design possibilities. Despite its small shape the SNT 40 is a fully accepted member of the family of Tronic transformers providing all product features and safety facilities known from the larger devices. Design version Rated output voltage Mains current (40 W) Power factor flexible connection cables designed with potentiometer AC 240 V ~ version on request W 11.7 V 0.18 A 0.96 c Efficiency 95 % Housing temperature t c Secondary line min mm 2 Short-circuit protection Overload / Temp. protection No load Softstart Fire protection Safety class Dimmable Marks of conformity max. +50 C at maximum load max. +85 C at maximum load electronic switch-off, automatic restart automatic power reduction protected lamp-saving starting switch-off in case of fault covered version with potentiometer MM, ENEC, VDE 73 x 35.5 x 18 mm Poti transformers are designed for installation in appliances and luminaires with LV halogen lamps. The cables lead out on the primary are designed with rotary potentiometer and turn-off-switch. Switching of the lamp and setting of the brightness is thus very easy. Suitable for fitting in e.g.: workplace luminaires, lamps for bathroom cabinets, furniture illumination and optical devices. Thread

11 Tronic Trafo 11 SNT 70 / QU W SND 70 / QU Poti-Trafo W Art.-no Art.-no Design version flexible connection cable AC 240 V ~ version on request W Rated output voltage 11.7 V Mains current (70 W) 0.33 A Power factor 0.96 c Efficiency 95 % max. +40 C at 70 W / max. +50 C at 60 W Housing temperature t c max. +75 C at maximum load Secondary line min mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection temperature switch-off No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV 60 (49) x 48 x 28 mm Design version flexible connection cable, with potentiometer AC 240 V ~ version on request W Rated output voltage 11.7 V Mains current (70 W) 0.33 A Power factor 0.96 c Efficiency 95 % max. +40 C at 70 W / max 50 C at 60 W Housing temperature t c max. +75 C at maximum load Secondary line min mm 2 Short-circuit protection electronic switch-off, automatic re-start Overload / Temp. protection temperature switch-off No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class covered version Dimmable with potentiometer Mark of conformity MM, VDE, ENEC 60 (49) x 48 x 28 mm The SNT 70/QU with its square shape and small size is excellently suitable for perfect low-voltage lighting technique in furniture and luminaire construction. With its square shape it can be installed in places where cubic devices could not be installed. Excellent fitting versions are possible with its housing height of only 28 mm and an edge length of 49 mm. Two assembly clips facilitate the fastening. Poti transformers are designed for installation in appliances and luminaires with LV halogen lamps. The cables lead out on the primary are designed with rotary potentiometer and turn-off-switch. Switching of the lamp and setting of the brightness is thus very easy. Suitable for fitting in e.g.: workplace luminaires, lamps for bathroom cabinets, furniture illumination and optical devices. Thread

12 12 Tronic Trafo SNTF 70 / SR W SND 105 / Poti-Trafo W Art.-no Art.-no Discontinued item, only small quantities available. Design version Rated output voltage Mains current (70 W) Power factor with screw terminals, with strain relief AC 240 V ~ version on request W 11.7 V 0.33 A 0.96 c Efficiency 95 % Housing temperature t c Secondary line min. 1.5 mm 2 Short-circuit protection Overload / Temp. protection No load Softstart Fire protection Safety class Dimmable Marks of conformity max. +50 C at maximum load max. +70 C at maximum load electronic switch-off, automatic restart automatic power reduction protected lamp-saving starting switch-off in case of fault II with Tronic dimmer and universal dimmer MM, ENEC, VDE, VDE-EMV 152 x 43.5 x 17.5 mm Flat casing for installation in furniture, primary and secondary with screw terminals and strain relief. This Tronic transformer with a height of only 17.5 mm offers the interior designer manifold possibilities for the inte gration of LV halogen lighting technique in furniture and interior furni shings. In pedestals or niches, underfloor or behind cabinet backs this flat transformer can easily be fitted. Its power range provides enough play in the choice of number and power consumption of the LV halogen lamps used. Design version flexible connection cables with potentiometer Rated output voltage Mains current (105 W) Power factor AC 240 V ~ version on request W 11.8 V 0.49 A 0.96 c Efficiency 95 % Housing temperature t c Secondary line min. 1.5 mm 2 Short-circuit protection Overload / Temp. protection No load Softstart Fire protection Safety class Dimmable Marks of conformity max. +50 C at maximum load max. +75 C at maximum load electronic switch-off, automatic restart automatic power reduction protected lamp-saving starting switch-off in case of fault covered version with potentiometer MM, ENEC, VDE 134 x 42 x 32 mm Poti transformers are designed for installation in appliances and luminaires with LV halogen lamps. The cables lead out on the primary are designed with rotary potentiometer and turn-off-switch. Switching of the lamp and setting of the brightness is thus very easy. Suitable for fitting in e.g.: workplace luminaires, lamps for bathroom cabinets, furniture illumination and optical devices. Thread

13 Tronic Trafo 13 SNT 105 / SR W SNT 105 / SR W Art.-no V Art.-no V Design version with screw terminals, with strain relief W Rated output voltage 11.8 V Mains current (105 W) 0.49 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV 152 x 42 x 32 mm Design version with screw terminals, without strain relief W Rated output voltage 11.8 V Mains current (105 W) 0.49 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class covered version Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE 134 x 42 x 32 mm Important features are the ergonomic shape and the low minimum load of 20 W. With this transformer the designer of luminaires has more leeway in the number of LV-halogen lamps used. At the same time, the large power range of these transformers optimizes stock-keeping and makes retrofitting more flexible. The double terminals on the primary are suitable for throughconnection of two conductors. Easy connection and installation by 3 terminal pairs on the secondary, e.g. for rapid connection of 3 x 35 W. Due to its favourable size the version without strain relief is highly suitable for fitting in small recesses in luminaires, in furniture, bathroom cabinets, etc. Fewer technical constraints, more freedom for the design.

14 14 Tronic Trafo SNT 105 / ZY W SND 105 / ZY W Art.-no No longer available. Art.-no No longer available. (with Poti) Design version flexible cables AC 240 V ~ version on request W Rated output voltage 11.7 V Mains current (105 W) 0.44 A Power factor 0.96 c Efficiency 95 % max. +45 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer or universal dimmer Marks of conformity MM, ENEC, VDE ø 78.5 x 35 mm Design version flexible cables AC 240 V ~ version on request W Rated output voltage 11.7 V Mains current (105 W) 0.44 A Power factor 0.96 c Efficiency 95 % max. +45 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class covered version Dimmable with potentiometer Mark of conformity MM ø 78.5 x 35 mm The cylindrical shape allows fabrication of compact luminaires, rail spotlights, cylindrical ceiling and suspended luminaires with integrated transformer, e.g. in the baldachin or foot of the light. Cylindrical transformers are also suitable for pre-assembly in fitting cups in the ceiling. The version with poti has the cables lead out on the primary prepared with rotary potentiometer and turn-off-switch. Thus switching and dimming is possible. Thread

15 Tronic Trafo 15 SNTI 105 / SR W SNTF 105 / SR W Art.-no Discontinued item, only small quantities available. Art.-no Design version with screw terminals, with strain relief Design version with screw terminals, with strain relief Rated voltage AC 230 / 240 V ~ W W Rated output voltage 11.8 V at 240 V, 11.3 at 230 V Rated output voltage 11.8 V Mains current (105 W) 0.45 A Mains current (105 W) 0.45 A Power factor 0.96 Power factor 0.96 c Efficiency 92 % Efficiency 95 % max. +45 C at maximum load max. +50 C at maximum load Housing temperature t c max. +80 C at maximum load Housing temperature t c max. +80 C at maximum load Secondary line max. 2 m long, min 1.5 mm 2 Secondary line min. 1.5 mm 2 Short-circuit protection yes Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection yes Overload / Temp. protection automatic power reduction No load protected No load protected Fire protection switch-off in case of fault Softstart lamp-saving starting Safety class II Fire protection switch-off in case of fault Dimmable with LV leading-edge dimmer Safety class II with Tronic Dimmer Dimmable with Tronic dimmer and universal dimmer with universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV Marks of conformity MM, ENEC, VDE, VDE-EMV 175 x 42 x 18 mm 105 x 50 x 29 mm The new Tronic Trafo SNTI 105/SR was designed to save space. Its special feature is its dimmability in LV leading- and trailing edge which makes it also suitable for use in Great Britain. It can be installed in ceilings through downlight holes of ø 55 mm. This requires a free ceiling height of only 60 mm. Owing to latest technical developments in electronics and mechanics, the SNTI 105/SR is very cost-effective. The Tronic-transformer SNTF 105 for low-voltage halogen lamps is flatter than the old type and more efficient. Thanks to its height of only 18 mm it can easily be integrated in furniture and interior fittings. With its load range of W it offers the lighting designer more leeway for creative LV lighting concepts.

16 16 Tronic Trafo SNTF 105 / LI W SNTF 105 / SR W Art.-no Art.-no Design version prim. with 2 pairs of screw terminals, with strain relief Design version sec. 1.0 mm 2 double flexible 0.2 m AC 240 V ~ version on request W Rated output voltage 11.8 V Mains current (105 W) 0.45 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +80 C at maximum load Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction up to 70 %, then switch-off No load protected Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV 165 x 42 x 18 mm Design version prim. with 2 pairs of screw terminals, with strain relief Design version sec. 1 pair of screw terminals AC 240 V ~ version on request W Rated output voltage 11.8 V Mains current (105 W) 0.45 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +80 C at maximum load Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction to 70 %, then switch-off No load protected Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV 175 x 42 x 18 mm The SNTF W is one of the youngest members of the Tronic Trafo family. Compared to the SNTF W, Art.-no , this new type, as convenient installation transformer for clamping of any type of cables and with 18 mm construction height and prepared secondary cable, is particularly suitable for furniture and lighting industry. Electrically, the SNTF 105/SR W is identical with the opposite SNTF 105/LI. It has a different housing construction and instead of the flexible on the secondary it has only one pair of screw terminals.

17 Tronic Trafo 17 SNTF 105 / SR W SNT 105 / 1-10 V Art.-no Art.-no Art.-no V 240 V Discontinued item, only small quantities available. Design version prim. with 2 pairs of screw terminals, with strain relief Design version sec. 3 pairs of screw terminals AC 240 V ~ version on request W Rated output voltage 11.8 V Mains current (105 W) 0.45 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +80 C at maximum load Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction to 70 %, then switch-off No load protected Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM 175 x 42 x 18 mm Design version with screw terminals, with strain relief AC 240 V ~ 50 Hz W Rated output voltage 11.8 V Mains current (105 W) 0.45 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable by control devices (1-10 V) Control current max 0.8 ma Marks of conformity VDE, MM, ENEC 216 x 42 x 32 mm Electrically, the SNTF 105/SR W is identical with the SNTF 105/SR. It differs by the number of terminal pairs on the secondary. In this case 3 terminal pairs. In large modern lighting systems more and more lamps are operated by EVGs (electronic ballasts) that are equipped with a 1-10 V control input. Thus also high loads can be switched and dimmed centrally. This control principle has also been realised for the SNT 105 / 1-10 V, so that it can be integrated in 1-10 V systems.

18 18 Tronic Trafo SNT 150 / SR W SNT 200 / SR W Art.-no Art.-no Design version with screw terminals, with strain relief AC 240 V ~ version on request W Rated output voltage 11.7 V Mains current (150 W) 0.71 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 2.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, ENEC, VDE, VDE-EMV 176 x 42 x 38 mm Design version with screw terminals, with strain relief AC 240 V ~ version on request 50 Hz W Rated output voltage 11.5 V Mains current (200 W) 1 A Power factor 0.96 c Efficiency 95 % max. +50 C at maximum load Housing temperature t c max. +65 C at maximum load Secondary line min. 2 x 2.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload / Temp. protection switch-off No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with Tronic dimmer and universal dimmer Marks of conformity MM, VDE, VDE-EMV, ENEC 212 x 48.5 x 46 mm The SNT 150 combines high power consumption and small shape. It has the small shape of 105 W devices but offers the light designer a great choice of LV halogen lighting profiles. The primary double terminals are suitable for through-connection of two conductors. Easy connection and installation by 3 secondary terminal pairs, e.g. for rapid connection of 3 x 50 W. To be used ideally for the creation of a»starry sky«by means of up to 40 halogen lamps of 5 W each. Double terminals are installed on the primary and on the secondary.

19 Tronic Trafo 19 ST 105 / W 6-fold distributor Art.-no Art.-no Art.-no other colours on request black white gold Discontinued item, only small quantities available. Discontinued item, only small quantities available. Art.-no No longer available. Design version with screw terminals with strain relief AC 240 V ~ version on request 50 Hz W Rated output voltage 11.8 V Mains current (105 W) 0.5 A Power factor 0.96 c Efficiency 95 % max. +45 C at maximum load Housing temperature t c max. +75 C at maximum load Secondary line min. 1.5 mm 2 Short-circuit protection electronic switch-off, automatic restart Overload/Temp. protection automatic power reduction No load protected Softstart lamp-saving starting Fire protection switch-off in case of fault Safety class II Dimmable with integrated potentiometer 150 x 70 x 36 mm Design version Cable length Supply voltage Rated currents Marks of conformity with flexible cable 80 mm V eff max. 42 V I eff max. 17 A for the input I eff max. 8,5 A for each branch 200 W max. +50 C at maximum load VDE, SEV, FIMKO, NEMKO 86 x 40 x 23.5 mm The 6-fold distributor with flexible connection cable is suitable for connection to various types of Tronic transformers. Lampwires will be connected by spring plug-in terminals. Its preferred use is in such places where, for space or fitting reasons, the transformer/distributor combination must be flexible. The 6-fold distributor can also be used in connection with conventional 50 Hz transformers if the technical limit values of the 6-fold distributor are not exceeded and if the 50 Hz transformer has got a fuse. Dimmable electronic cord transformer to be fitted into the feed cable of table and floor lamps with LV halogen lamps. Connection between lamp(s) and mains. Continuous brightness control by means of a slide potentiometer.

20 20 Tronic Trafo Over voltage protection module EMC-module 0.31 A Art.-no Discontinued item, only small quantities available. Art.-no Hz Leakage current 4,5 ka (1x) / 1 ka (100 x) Residual voltage 1000 V Operation temperature C Connections Installation Protection range flexible wire 1,5 mm 2 / 80 mm long parallel to main circuit 1 module for approx Tronic Trafo per circuit 45 x 25 x 22 mm Tronic transformers are protected against spikes according to EN Spikes, that may occur when fluorescent lamps, discharge lamps or other inductive loads are switched off, may have so much energy to influence or destroy electronic transformers. Installed in front of up to 10 Tronic transformers if possible, the module reduces spikes to a harmless degree. Rated voltage AC 250 V ~ Rated current 70 VA 0.31 A Mains line L, N = 0.5 mm 2, PE = 0.75 mm 2 Cable length with wire end sleeves 180 mm 38 (30) x 20 x 17 mm Very small module for EMC interference suppression with metallic luminaires (protection class I) containing a ballast, a Tronic-transformer or other electronic components. Even if the components themselves have been tested acc. to EMC, the limit values in the metallic luminaire might be exceeded. The EMC-module prevents this. It can be used for lights with an input power up to 70 VA.

21 21

22 zwe 22

23 23 For ballasts with 1-10 V control input For DALI HV cord dimmer W with sliding poti page 24 KNX-DALI gateway page 28 HV built-in dimmer W page 24 DALI power poti, flush-mounted page 28 HV built-in dimmer module W page 25 Rotary poti module page 25 Light sensor 1-10 V page 26 For 50 Hz transformers and mains voltage operation Tronic built-in dimmer 700 W page 29 Tronic built-in power booster 700 W page 29 For mains voltage operation Electronic potentiometer 1-10 V page 26 Push-button control device for electronic ballasts 1-10 V page 27 SNT 105 / 1-10 V page 27 LV cord dimmer W/VA with sliding poti page 30 Built-in push-button dimmer module W/VA page 30 LV built-in power booster 600 W page 31

24 30 24 Controls For ballasts with 1-10 V control input HV cord dimmer W with sliding potentiometer HV built-in dimmer W Art.-no black Art.-no white Art.-no gold other colours on request No longer available. No longer available. Art.-no Dimming principle Leading edge Rated voltage AC 230 / 240 V ~ Operation Connection 50 Hz sliding potentiometer screw terminals Fuse T 1,25 H 250 Marks of conformity VDE, ENEC 126 x 60 x 35 mm Dimmer for longitudinal fitting in the feed cable of mobile lights. The flat and anti-slip cord dimmer is particularly suitable for floor lights and foot-operation. Continuous dimming is effected by sliding. The fuse holder which is accessible from outside allows an easy change of the melting fuse. Dimming principle Leading edge Operation 50 Hz rotary potentiometer +50 ºC Connection Fuse T 1 H 250 Mark of conformity with cables lead out VDE 70 x 35 x 19 (36) mm The built-in dimmer is also available as compact device for direct integration in a light and contains an integrated rotary potentiometer. The axis of the potentiometer can be installed later. Thus fitting in very small recesses is possible. The built-in dimmer is fastened in the housing of the light by means of a hexagonal nut. It contains an integrated fuse. The user can easily change the fuse from outside. Ø M10 x 0,75 4, 6 1, ,5 65,5 8 30,5 35 ca

25 Controls For ballasts with 1-10 V control input 25 HV built-in dimmer module W Rotary potentiometer module Art.-no Discontinued item, only small quantities available. Art.-no Dimming principle Leading edge Operation Connection 50 Hz rotary or sliding potentiometer Fuse T 1 H 250 max +50 ºC at maximum load with cables lead out 70 x 35 x 19 mm Built-in dimmer modules contain the dimming power electronics and are designed for installation in mobile or stationary lights like e.g. table, floor or wall lights. Brightness control is effected by means of potentiometer modules which are connected via a control lead. The connections for both lamp load and control cables are prepared. Their small and favourable dimensions as well as the easy fastening by lashes at the bottom of the housing must be stressed. Potentiometer axis ø 6 mm Resistivity 270 k linear 10% Connection Operation max. +50 ºC at maximum load screw terminals turning 26 x 20 x 17 (34.5) mm The rotary potentiometer module is suitable for built-in dimmer modules. The device is completely encapsulated and can be integrated in lights of protection class II according to DIN/VDE 630, part 12. No further insulations are necessary. The control cables are connected by means of connection terminals. The axis of the rotary potentiometer can be hidden after assembly so that this module can be fitted through very small openings in the light ,5 3, 2 M 10 x 0,75 4,6 7, ,5 35 1, ca Ø 6

26 26 Controls For ballasts with 1-10 V control input Light sensor 1-10 V Electronic potentiometer 1-10 V Art.-no No longer available. Art.-no switching function Art.-no push-button function See Lightment Overview Supply Control current via 1-10 V interface max. 10 ma Detection angle approx. 50º Control range approx lx ø 46 x 17.5 mm This module in minimized shape for automatic constant light control is suitable e.g. for installation in ceilings for working place illumination. It is connected directly to the 1-10 V control input of the luminaire. It reduces the brightness of the luminaire if the working place is sufficiently illuminated by daylight. Thus beneath the luminaire there is a constant light level whose basic brightness can be preset at the module. This brings the desired lighting conditions and reduces energy consumption and costs. Control current max. 50 ma Switching current (resistive load) max. 6 A (switching function) max. 2 A (push-button function) Control voltage V Galvanic separation 1-10 V 2 kv- basic insulation Connection screw terminals Fuse F 500 H 250 (integrated) Marks of conformity VDE 70.7 x 70.7 x 21 mm Axis dimensions ø 4 mm Accessories button Art.-no cover Art.-no In modern lighting technology more and more lamps, e.g. fluorescent lamps or halogen lamps, are operated with electronic ballasts with 10 V control input. If the 10 V control inputs of all electronic ballasts in extensive lighting systems are connected to one another and operated by the electronic potentiometer, the whole lighting system can be switched and dimmed centrally M 10 x

27 Controls For ballasts with 1-10 V control input 27 Sensor control unit for EVG 1-10 V SNT 105 / 1-10 V Art.-no Art.-no V Art.-no V Discontinued item, only small quantities available. Operation Switching contact Summation current EVG Upstream circuit breaker No load proof Galvanic separation 1-10 V 50 Hz touching Relay max. 200 ma 10 A yes 2 kv- basic insulation max. +50 C Protection rating IP 20 Terminals Mark of conformity N, 1, L,, + (3x), - (3x) ÜG VDE 175 x 42 x 18 mm Flat built-in unit for switching and controlling of electronic ballasts with 1-10 V interface. It differs from our»electronic potentiometer«by its mode of operation: all switching and dimming commands are given by push-button operation and by the possibility of connecting any number of push-buttons as fully valid extensions. Depending on the control voltage of the used ballast and the use of additional power switches, more than 100 EVG can be controlled simultaneously. Three pairs of output terminals facilitate the connection of the devices. Design version with screw terminals with strain relief Rated output voltage Primary current (105 W) Power factor AC 240 V ~ 50 Hz W 11.8 V 0.45 A 0.96 c Efficiency 95 % Housing temperature t c Secondary line min. 1.5 mm 2 Short-circuit protection Overload / Temp. protection No load Softstart Fire protection Safety class max. +50 C at maximum load max C at maximum load electronic switch-off, automatic restart automatic power reduction protected lamp-saving starting switch-off in case of fault Dimmable by control devices (1-10 V) Control current Marks of conformity II max 0.8 ma VDE 216 x 42 x 32 mm In large modern lighting systems more and more lamps are operated by EVGs (electronic ballasts) that are equipped with a 1-10 V control input. Thus also high loads can centrally be switched and dimmed. This control principle has also been realised for the SNT 105 / 1-10 V, so that it can be integrated in 1-10 V systems.

28 28 Controls For DALI KNX-DALI gateway DALI power poti, flush-mounted Art.-no No longer available. Art.-no See Lightment Overview Rated voltage AC V ~ Shape RMD, 4 modules ºC Protection rating IP 20 Power consumption Connection Display / operation elements No load Overtemperature protection Controllable channels Interface approx. 6 W KNX bus terminal screw terminals for mains screw terminals for DALI 3 LED, 1 LED display / 4 keys protected no, not necessary 32 groups / 16 scenes 72 x 90 x 62 mm KNX / DALI KNX systems Programming Operation of the lighting system DALI-communication none pressing, turning (endless-poti) -5 C +45 C Power consumption Connection max. 2.0 W screw terminals Cable section 1 4 mm 2 Fuse Marks of conformity Diameter of axis Interface Accessories none (electronic) VDE 70.7 x 70.7 x 32 mm ø 4 mm DALI Button (pure white) Art.-no Cover (pure white) Art.-no stations without additional DALI power supply number of DALI stations to 104 of the integrated power supply)

29 Controls For 50 Hz transformers and mains voltage operation 29 Tronic built-in dimmer 700 W Tronic built-in power booster 700 W Art.-no Discontinued item, only small quantities available. Art.-no No longer available. Dimming principle Trailing edge Dimming principle Trailing edge 50 Hz 50 Hz Soft start yes Soft start yes Operation by flush-mounted push-button Operation by Tronic dimmers max. +45 C Housing temperature t c max. +70 C Automatic switch-off in case of max. +45 C Housing temperature t c max. +70 C Automatic switch-off in case of Short circuit electronic switch-off Short circuit electronic switch-off autom. restart for t < 7s autom. restart for t < 7s Connection screw terminals Connection screw terminals Marks of conformity VDE, SEMKO, DEMKO, FIMKO Marks of conformity VDE 212 x 48.5 x 46 mm 212 x 48.5 x 46 mm The Tronic built-in dimmer as trailing-edge dimmer is designed for installation in recessed ceilings. It is controlled by common flush-mounted pushbuttons with the following operation principle: short touch = on/off switching of the lighting system, long touch = continuous dimming. By connection of Tronic built-in power boosters (Art.-no ) the power of the Tronic built-in dimmer can be increased considerably. The Tronic built-in power booster is used for the family of Tronic dimmers (Tronic flush-mounted dimmer and Tronic built-in dimmer), in order to increase the power by 700 W each. By parallel switching of several power boosters lighting systems up to 7 kw can be controlled by one dimmer.

30 30 30 Controls For mains voltage operation LV cord dimmer W/VA with sliding potentiometer Built-in push-button dimmer module W/VA Art.-no Art.-no Art.-no Other colours on request black white gold Discontinued item, only small quantities available. No longer available. No longer available. Art.-no Dimming principle Leading edge hasenanschnitt Rated voltage AC 230 / 240 V ~ 50 Hz Operation sliding potentiometer Connection screw terminals Fuse T 3,15 H 250 Marks of conformity VDE, ENEC 126 x 60 x 35 mm Dimming principle Leading edge 50 Hz Ambient temperature ta +40 ºC Operation Micro push-button module 230 V AC Connection screw terminals / with cables lead out Fuse T 1.25 H 250 V (external) Mark of conformity VDE 81 x 43 x 20 mm Dimmer for longitudinal fitting in the feed cable of mobile lights. The flat and anti-slip cord dimmer is particularly suitable for floor lights and foot-operation. Continuous dimming is effected by sliding. The fuse holder which is accessible from outside allows an easy change of the melting fuse. The built-in push-button dimmer module contains the dimming power electronics and is designed for installation in mobile or stationary lights. Brightness control is effected by means of a micro push-button module. The connections for both lamp load and control cable to the micro push-button are prepared by feed cables or terminals. New: In this optimized version, now also switching via mains voltage (switched socket-outlet) is possible. The preset dimming value is maintained. Micro push-button module 2.1 m Art.-no Connection Drill hole for mounting Operation axis cables (2.1 m) with wire end sleeves ø 6.5 mm ø 4 mm approx. 40 x ø 10.5 mm

31 Controls For mains voltage operation 31 LV built-in power booster 600 W Art.-no Discontinued item, only small quantities available. Dimming principle Leading edge 50 Hz max. +45 C Housing temperature t c max. +70 C Automatic switch-off in case of Connection screw terminals 212 x 48.5 x 46 mm The LV built-in power booster works in leading edge and increases the power of all LV dimmers for conventionally coiled transformers also working in leading edge. By parallel switching of up to 10 LV built-in power boosters, lighting systems up to approx. 6 kw total power, built with conventional coiled transformers, can be controlled by one dimmer. Attention! This product must not be used in combination with Tronic build-in dimmer 700 W and Tronic build-in power booster 700 W, since these work in trailing edge.

32 32

33 33

34 zwe 34

35 35 instafunk light control panel page 38 instafunk switch ZS / instafunk dimmer ZS page 43 instafunk hand transmitter page 38 instafunk control unit 1-10 V, built-in page 44 instafunk hand transmitter, mini page 39 instafunk control unit, triple page 44 instafunk wall transmitter, flat page 39 instafunk universal dimmer, built-in page 45 instafunk-universal transmitter page 40 instafunk universal cord dimmer page 45 instafunk multi function transmitter 4-line page 40 instafunk presence detector page 41 instafunk single switching actuator / keying actuator, mini page 41 instafunk double switching actuator, mini page 42 instafunk shutter actuator page 42 instafunk switching actuator, built-in page 43

36 36 instafunk is a wireless radio control system. Its advantage is easy retrofitting. The comfort of an existing system can clearly be enhanced without additional control leads. High flexibility is obtained by the possibility of integrating mobile luminaires. Wireless function instafunk allows wireless switching and control of individual or group lights or light scenes, through to broadcast commands. All lamp types - HV and LV lamps, long-field lamps and compact fluorescent lamps as well as the corrsponding ballasts like electronic ballast with 1-10V interface can be controlled on radio basis. The instafunk components listed below can be combined sensibly in a lighting project so that instafunk becomes a problem-solving, several-room-control light control system. These are for instance: wall transmitter, universal transmitter actuator, 1-10 V control unit In contrast to the well-known remote control systems based on infrared radiation, the instafunk system uses electro-magnetic waves for the transmission of control telegrams. The electro-magnetic rays propagate radially and permeate walls and furniture. Easy commissioning Programming of an installation within the instafunk system is effected by easy learning processes between transmitter and receiver a PC-supported member definition is not required. Theoretically, each transmitter can address an infinite number of receivers, the receivers can be programmed to 30 transmitters each, without demanding programming knowledge from the user. Quality assurance For instafunk applications the communication transmission on a frequency of 433 MHz has proven itself in practice. Compared to low-cost systems the instafunk system is considerably more narrow-banded. It works more selectively and thus is less sensitive to interferences from outside. The instafunk system components have an individual serial number excluding mutual influence of parallel systems. Active influence from outside, e.g. by radio amateurs (interferers) is also excluded, so that the products offer a high operation reliability. Fields of use Ranges The typical transmission range of a RF transmitter is 100 m and depends on the construction characteristics of the object. approx db damping corresponds to approx % range ping corresponds to approx. 30 % range corresponds to approx. 10 % range approx db damping corresponds to approx % range Construction materials, particularly metal or metal coatings, might dampen the radio signal. In this case the Insta repeater can be used. The repeater is installed centrally and ensures transmission of the signals by receiving and passing on of the signals. Repeater on request. Europe-wide use Since April 2001 admission processes for radio products have been controlled by a common European guideline. The guideline R&TTE 1999/5/ EG (Radio equipment and Telecommunications Terminal Equipment) in general is based on a device check by independent authorities. If the devices meet all requirements, they may be used in all EU and EFTA states. The Insta products have passed all relevant tests before they are placed onto the market.

37 37 Health-friendliness The radiation reaching the human being when using the instafunk system is by factor 100,000 lesser than e.g. the radiation of a mobile phone. There is radiation only during operation so that instalight RF can particularly be recommended for mains isolation. Compatibility instafunk system components can also be used as linked subsystem within KNX and LEDTRIX. Fields of use With the instafunk-components Insta offers light manufacturers versatile products whose functions and advantages are normally known from wired bus systems only. The instafunk-components can be installed directly into the lights. Insta offers integrable components for all standard light systems. Possible applications Multi-room lighting control, e.g. for shops or presentation rooms KNX can be supplemented by comfortable, user-friendly operation possibilities like instafunk hand and wall transmitters Managable light management solution for private homes Advantages Wireless signal transmission, no additional wiring necessary for the control Easy device allocation by pressing of a button (push button mode) Easy integration of any kind of sensorics via instafunk multi-function transmitter Flexible retrofitting

38 38 instafunk instafunk light control panel instafunk hand transmitter Art.-no Art.-no Art.-no No longer available. Design frame, white Design frame, silver Art.-no hand transmitter comfort No longer available. Art.-no hand transmitter vario Discontinued item, only small quantities available. Power consumption approx. 6 W Possible channels 24 channels Light scenes all ON, all OFF, 5 light scenes Channel allocation easy programming Transmitting range in free field typ. 100 m Control for receivers of the instafunk system reception of instafunk transmitters optional Carrier frequency (ASK) MHz ºC Neutral conductor, exterior conductor screw terminals, max. 2.5 mm 2 Exterior dimensions (incl. cover/ frame) 231 x 146 x 85 mm Interior dimensions 212 x 124 x 75 mm Interface RF Please always order frame for light control panel separately. Rated voltage DC 6 V Batteries 4 x 1.5 V micro LR03 (AAA), alcaline Possible channels 3 groups with 8 channels each Light scenes all ON, all OFF, 5 light scenes Operation separate push-buttons for: ON / OFF and UP / DOWN Special functions operation of 5 light scenes light scene dimming function Channel allocation easy programming Transmitting range in free field typ. 100 m Control for all receivers of the instafunk system Carrier frequency (ASK) MHz Colour anthracite 192 x 53 x 22.5 mm Interface RF Battery set Art.-no Please always order battery set separately. The instafunk light control panel is designed for convenient control of all instafunk receivers. Via menue assistance functions like switching, dimming, shutter, light scenes can be configured and carried out. Easily comprehensible and visually. Automatic light scene sequences can be programmed. The instafunk hand transmitter is suitable for control of all instafunk receivers. The»two point operation«enables selective switching and dimming per channel. Altogether 3 groups with 8 channels each, i.e. 24 targets, are available. The comfort version additionally offers the feature to create, to call-up and to dim light scenes as a whole.

39 instafunk 39 instafunk hand transmitter, mini instafunk wall transmitter, flat Art.-no No longer available. Art.-no Discontinued item, only small quantities available. Rated voltage Batteries Possible channels 2 Special channels Operation Channel allocation Transmitting range in free field Control Carrier frequency (ASK) Colour Interface DC 3 V 1 x button cell CR2032, lithium included in scope of supply none separate push-buttons for: ON / OFF and UP / DOWN easy programming typ. 30 m all receivers of the instafunk system MHz anthracite 73 x 40 x 19 mm RF Due to its mini shape and the integrated fastening lash, the user can take its instafunk hand transmitter with him at any time: at his bunch of keys, at his waist-band or at the working place, any time at hand. Due to the two point operation the two channels allow selective switching and dimming of two lights or combined light groups. Rated voltage Batteries Channel allocation Possible channels 4 Special channels Transmitting range in free field Control Carrier frequency (ASK) DC 6 V 2 x button cell CR 2016 lithium included in scope of supply easy programming to be converted to: All Off and 5 light scenes typ. 30 m all receivers of the instafunk system MHz ºC Protection rating IP 20 Use Colour Interface in dry rooms only white 81 x 81 x 17 mm RF Special feature of this device is its extremely flat shape. Two lithium button cells, included in the scope of supply, provide the transmitter with the voltage required. The transmitter is mounted without cables by sticking or screwing it onto a flat surface like, for instance, plaster, wood, glass, mirror. Up to four actuators of the instafunk system can be remote controlled individually. The instafunk wall transmitter is equipped with a triple function switch by which the function of the keys can be chosen. This includes special functions like»all OFF«or»light scene«.

40 40 instafunk instafunk universal transmitter instafunk multi-function transmitter, 4-channel Art.-no No longer available. Art.-no No longer available. Transmitting range in free field Carrier frequency (ASK) typ. 100 m MHz C Interface approx. ø 52 x 23 mm RF The instafunk universal transmitter extends an existing installation by wireless transmission of 230 V switching commands. It can be operated in the functions switching, dimming or shutter. If the inputs (E1/E2) are driven with mains voltage (230 V AC), the universal transmitter sends RF telegrams which are evaluated by all RF receivers. The RF universal transmitter has 4 operation modes: Mode A: 2-channel dimming (toggling, E1 and E2) Mode B: 2-channel switching (E1 and E2) Mode C: 1-channel dimming (E1/E2) Mode D: 1-channel blind/shutter (E1/E2) Rated voltage Batteries Cable length Inputs Transmitting range in free field Carrier frequency (ASK) DC 3 V 1 x button cell CR 2032 lithium 290 mm 4, floating typ. 100 m MHz ºC Use Interface in dry rooms only 45 x 40 x 10 mm RF This product is battery-powered and allows wireless transmission of switching- and push-button commands to instafunk receivers. Five DIP-switches can be set individually so that this device can be used as opener/ closer/pushbutton or switch. Functions like switching/dimming/all on/all off or light scenes are possible. Thus the transmitter is suitable for installation in floor lights which are used as master lights. Via micro push-buttons in the stand of the light further lights of this family of products can thus be operated.

41 instafunk 41 instafunk presence detector instafunk single switching / push-button actuator, mini Art.-no No longer available. Art.-no Art.-no instafunk switching actuator instafunk push-button actuator No longer available. Discontinued item, only small quantities available. Rated voltage Batteries DC 6 V Detection angle 360º Rated detection range at table height Rated detection range on the floor Build-in height for rated detection range Lighting time Brightness setting Receiver allocation Transmitting range in free field Carrier frequency (ASK) Colour Interface 4 x 1.5 V Micro LR03 (AAA), alcaline ø 5 m ø 8 m 2.5 m approx min approx lx easy programming typ. 100 m MHz white ø 103 x 42 mm Battery set Art.-no Please always order battery set separately. RF The battery-fed, cable-less instafunk presence detector is installed at the ceiling and monitors a working place beneath. When the preselected brightness is underpassed and movement is detected, the detector switches on lights or light groups by RF-signal which are equipped with instafunk devices. It switches off when over a certain period of time no movement has been detected. By means of an integrated brightness sensor a constant light control is possible. The advantage is high energy saving. Switching contact relay (8 A) Possible transmitters max. 14 Channel allocation Control Carrier frequency (ASK) Interface max. 750 VA with conv. 50 Hz transformers max. 400 VA parallely compensated max VA duo switching easy programming all transmitters of the instafunk system MHz approx. ø 52 x 23 mm with centre hole ø 7.5 mm RF With its small mounting size the instafunk switching actuator, single, is ideally suitable for mounting in smaller wall- or table lights. The actuator switches a connected load as soon as it receives a programmed RF telegram. Up to 14 individual instafunk transmitters can be programmed. The instafunk push-button actuator mini shuts its relay contact as long as it receives programmed RF telegrams for switch-on (e.g. hand transmitter channel key). The contact remains shut for max. 16 sec.

42 42 instafunk instafunk double switching actuator, mini instafunk shutter actuator Art.-no Art.-no Rated voltage AC 230 / 240 V ~ Switching contact Possible transmitters Channel allocation Control Carrier frequency (ASK) Interface 10 A max VA with conv. 50 Hz transformers 920 VA parallely compensated not released duo switching max. 7 per channel easy programming all transmitters of the instafunk system MHz approx. ø 53 x 28 mm RF The instafunk switching actuator, double, has the same small mounting size as the single version. The actuator switches two connected loads independent of one another as soon as it receives a programmed RF telegram. Up to 14 individual instafunk transmitters can be programmed. Automatic cut-out Relay output Direction change Continuous operation Carrier frequency (ASK) 10 A 1 motor, 700 VA, max. 2 make-contacts potential-carrying and interlocked approx. 1 s approx. 2 min MHz approx C Relative humidity Protection rating IP 20 Number of progammable transmitters 14 Interface max. 65 % (without condens.) approx. 53 x 28 mm RF The instafunk shutter actuator allows remote control of a shutter motor. Depending on how the instafunk transmitter is operated, the slats are adjusted (short depression of the key < 1 s) or the shutter is driven (long depression of the key > 1 sec). The end position of the shutter (top/bottom) can be programmed, together with an illumination, in different light scenes.

43 instafunk 43 instafunk switching actuator, built-in instafunk switch ZS Art.-no Discontinued item, only small quantities available. Art.-no Discontinued item, only small quantities available. Switching contact relay (10 A) Possible transmitters max. 30 Channel allocation Control Carrier frequency (ASK) 1000 VA with conv. 50 Hz transformers 920 W parallely compensated 2300 W duo switching easy programming all transmitters of the instafunk system and extension push-buttonsv-switches MHz ºC Interface 175 x 42 x 18 mm RF This device is suitable for installation in or mounting at lights. The actuator switches the connected electric load as soon as it receives a programmed RFtelegram. The switching actuator also has an extension input for connection of standard installation push-buttons-switches for manual switching. The instafunk switching actuator can learn messages from up to 30 individual instafunk transmitters. Switching contact relay (6 A) switch dimmer Fuse Colour Interface max. 750 VA with induct. 50 Hz transformers W with conv. 50 Hz transformers T 6.3 H 250 V accessible from outside white 135 x 70 x 71 mm RF devices like table and floor lights at the device. additional dimming function.

44 44 instafunk instafunk control unit 1-10 V, built-in instafunk control unit, triple Art.-no Discontinued item, only small quantities available. Art.-no Function after power failure: off Art.-no Function after power failure: No longer available. start with pre-programmed colour sequence Switching contact Control current relay (8 A), max W resistive load max. 15 ma Possible transmitters max. 30 Channel allocation Control Carrier frequency (ASK) easy programming all transmitters of the instafunk system MHz ºC Interface 187 x 28 x 28 mm RF This compact built-in device is intended for installation in or mounting at lights. Electronic operation devices with 1-10 V control input (electronic ballasts and transformers) can be switched and dimmed by RF signal. Depending on the control voltage of the used ballast type and the use of additional power consumption switches 7-18 electronic ballasts can be controlled at a time. Rated voltage AC 230 / 240 V ~ Control current Automatic cut-out Transmitting range in free field Carrier frequency (ASK) max. 30 ma each channel 10 A Protection rating IP 20 typ. 100 m MHz approx C Interface 280 x 40 x 30 mm RF The instafunk control unit, triple 1-10 V is operated via hand transmitter comfort of the instafunk system. The triple control unit 1-10 V has been designed for comfortable realization of RGB-light mixtures, e.g. fluorescent lamps or LED-lamps. The lamps are controlled via three 1-10 V outputs.

45 instafunk 45 instafunk universal dimmer, built-in instafunk universal cord dimmer Art.-no Discontinued item, only small quantities available. Art.-no Discontinued item, only small quantities available. Dimming principle Leading and trailing-edge Rated power W / VA ºC VA with inductive 50 Hz transformers at a load of > 85 % Possible transmitters max. 30 Channel allocation easy programming Control all transmitters of the instafunk system Carrier frequency (ASK) MHz ºC 187 x 28 x 28 mm Interface RF Dimming principle Leading and trailing-edge Rated power W (minimum load required) max. 315 VA with conv. 50 Hz transformers at a load of > 85 % Possible transmitters max. 30 Channel allocation easy programming Control all transmitters of the instafunk system Carrier frequency (ASK) MHz ºC Colour black, others on request 126 x 60 x 28 mm Interface RF This device which can be controlled by all instafunk transmitters automatically knows the characteristics of the connected load (inductive, resistive or capacitive) and thus sets the suitable dimming process in leading or trailing edge. Ordinary tungsten filament lamps, HV and LV halogen lamps with Tronic transformers or 50 Hz transformers can be controlled. A simultaneous operation of Tronic transformers and 50 Hz transformers is to be avoided, all other loads can also be mixed. This device is installed into the feed cable of table or floor lights. It can be controlled by all instafunk transmitters and automatically knows the characteristics of the connected load (inductive, resistive or capacitive) and thus sets the suitable dimming process in leading or trailing edge. Tronic transformers and 50 Hz transformers, however, must not be connected at a time. All other loads can also be mixed.

46 46 List of article numbers 47 For further information please order our brochures. At or by phone Insta The company Lightment 1.1 Catalogue insta project Brochure on the service LED-illumination for indoor and productivity range and outdoor solutions of Insta Elektro GmbH lightment.insta.de