OT FIT 15/ /500 LT2 LP

Transcription

1 Preliminary OT FIT 15/ /500 LT2 LP SELV Constant current LED driver Wide operating area up to 500mA The reliable component when LEDset flexibility, small dimensions and low ripple are requested. Benefits Wide operating range: ma Low ripple Adjustable current via LEDset Long lasting and high reliability Built-in and independent mounting (with opt. kit) L L1 B B1 H 103 mm 94 mm 67 mm 58 mm 22.5 mm Approvals (Under preparation if not shown on label) Applications Downlight and spot. Office industrial shop VDE-ENEC VDE-EMC CCC RCM EAC Housing material: plastic, white Product Features Output current range ma Overload protection Low ripple <5% Over temperature protection Small and standard dimensions h lifetime at tc = 65 C SELV, Uout: VDC tc max = 75 C Output power up to 17.5 W Wide ta range C Mains voltage V 5 years guarantee Suitable for emergency lighting

2 Electrical Specifications Item Value Unit Remarks Nominal voltage V Nominal frequency 0 / Hz Incl. DC or pulse DC AC voltage range V DC voltage range V DC or pulse DC (>198V for starting) INPUT Maximum voltage 280 Vac 2 h maximum, unit might not operate in this abnormal condition Nominal current 0,1 A Total Harmonic Distortion (THD) < 15 % Full load, V, 50Hz / see graphs Power factor 0.95 Full load, V, 50Hz / see graphs Efficiency typical 84.0 % Full load, V, 50Hz / see graphs Power losses 3 W Maximum, full load No-load power - W OUTPUT DIMMING ENVIRONMENT Protection class II Suitable for class I and II luminaires Inrush current 14 A pk Max., th = 140µs Max. units per circuit breaker B10 = 38 B16 = 60 C10 = 64 C16 = 100 Nominal voltage range V Maximum voltage 60 V No load protection, Nominal current range ma Current accuracy +/- 5 % +/- 5% through the LEDset interface. Current ripple < 5 % Ripple / 100 Hz; Full load Nominal power range W Maximum power 17.5 W LED output Galvanic isolation kv SELV 3.75 Primary/secondary Output to earth - Touch current < 0.7 ma Emergency output factor C: EOF I = C: EOF I =0.51 Dimming control No Dimming range Dimming technique Frequency Galvanic isolation Ambient temperature range t a C Maximum case temperature t c 75 C Measured on t c point indicated of the product label, t a not exceeded Max. case temp. in fault condition 110 C Storage temperature range C Relative humidity % Not condensing Surge transient protection 1 2 kv L/N acc to. EN L+N / PE of basic isolated LED module Environmental rating Indoor IP rating IP 20 Mains switching cycles > Expected lifetime t h c = 75 C, 0.2% / h failure rate t c = 65 C, 0.1% / h failure rate Protections Overtemperature, Overload, No load, Short-circuit, Input overvoltage, Output overvoltage, Output undervoltage See remarks on page 4. Wiring Diagram Input Gray 1 - Mains Gray 2 - Mains Gray 3 - Mains Gray 4 - Mains Output Gray 21 LED - aux Gray 22 LEDset Gray 23 LED - Gray 24 LED + Load wires length: 2m max.

3

4 Remarks Input over voltage protection: mains up to 280 Vac, for 2 hours maximum, will not destroy both the unit and the load; shut down of load might occur in this condition. Output short circuit / under voltage protection: no destruction of unit Output overload protection: the unit automatically reduces the output current to keep the output power below 18W. Output over voltage protection: the unit reducing the current to maximum power; if Urated still exceeds 56V unit goes into blinking mode No load operation: repetitive start trials, safe for unit. Do not put a switch between load and unit. Over temperature protection: the unit is protected against temporary overheating by automatic reduction of the output current when tc > 80 C. The protection is self-restoring. Emergency lighting: this LED power supply is suitable for emergency lighting fixtures acc. to EN ; according to IEC Annex J. Touch current: lower than 0.7 ma, according to EN Annex G and EN Annex A

5 Optional Cable Clamp / Strain Relief An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. L W H 50 mm 67 mm 22 mm Position: C B A Position Cable types (tested acc. to EN ) Remark A or B Input / PRI Single cable only (one cable) NYM-J 3x1.5, NYM-J 4x1.5, NYM-J 5x1.5, NYM-J 3x2.5, NYM-J 4x2.5, NYM-J 5x2.5, H05VV-F 3x1.5, H05VV-F 3x1 A and B Input / PRI Mains through wiring (two cables) NYM-J 3x1.5, NYM-J 4x1.5, NYM-J 5x1.5, NYM-J 3x2.5, NYM-J 4x2.5, NYM-J 5x2.5 Through wiring current: max. 10A C Output / SEC NYM-J 3x1.5, NYM-J 4x1.5, NYM-J 5x1.5 Safety information for mains through wiring: Cable temperature in the cable clamp compartment depends on cable type, ambient temperature and through wiring current. Therefore maximum through wiring current is limited depending on the cable type. Standards Ordering information EN EN EN EN EN EN Product name EAN10 EAN40 Pieces / box OT FIT 15/ /500 LT2 LP OT Cable Clamp B-Style LP Manufacturer s address: OSRAM GmbH Steinerne Furt 62 D Augsburg Germany OSRAM GmbH Head Office: Marcel-Breuer-Strasse Munich, Germany Phone