Alarm-Display SD 9648

Transcription

1 Alarm-Display SD Digital- or 1 Digital- and 8 Analog inputs Features M Activation with voltage free contacts, 0/4 V signals or 0/ ma for monitoring of analog measuring values M First- or last message, priority M Internal and external reset M LCD-text display with background lighting lines, 16 characters each, 6.5 mm high M Text length max. 64 characters M Programming by frontside keypad M Acoustic alarm with integr. buzzer M Alarm relay, SPDT M Real-time clock M Front protection IP65 General The Alarm-Display SD9648 will be used for indicating and evaluations of alarm signals as well as analog measured values. Short information Sort mode The messages take place alternatively after their priority or after its occurrence (first/last message). Display mode Fault signals are cyclically or permanently displayed. With permanent announcement all messages can be queried by depressing the key. Display time It is programmable whether a message is deleted automatically after omission of the cause or additionally an acknowledgement is necessary. Relay / buzzer Parallel to the messages buzzers and/or alarm relay can be activated. Start-up-delay After switching on of the device, for an adjustable time by s all alarm signals are suppressed. Message delay time Programmable from s. Analog input Display range, alarm setpoints und alarm performance (min / max) are free programmable. Process values can be displayed at any place in the message. Date / time Can inserted in arbitrary place into a message (only with real-time clock), alternatively the current time or the time with the occurrence of an alarm. Note: With powerless device the inputs became a high resistance

2 Content Page Technical data... Connection diagram...3 Dimensions...3 Controls and indicators...4 Description...4 Programming...5 Error messages...1 Characters...13 Variables Programming examples...14 Ordering code...16 Start-up note: Before the device can be used, it must be configurated for the intended use. Technical data Power supply Supply voltage : 30V AC ±10%, 115V AC ±10%, 4V AC±10%, 4V DC ±15% Frequence AC : 50/60 Hz Power consumption : max. 3.5 VA Operating temperature : C Rated voltage : 50 V~ acc. to VDE 0110 between input/output/supply voltage degree of pollution, overvoltage categoric III Test voltage : 4kV=, between input/output/supply voltage - conformity : EN550, EN60555, IEC /4/5/11/13 Inputs Digital inputs Impulse/ break Analog inputs Accuracy Temperature coefficient Transmitter-supply : 0/4 V DC, Ri = 10 kω, switching threshold low <4 V, High >11 V max. 35 V : min. 10 ms : 0/ ma, Ri = 100 Ω voltage drop max.. V at 0 ma overload app. 3 ma (max. voltage 35 V). With powerless device the inputs became a high resistance : 0.1 %, ± 1 Digit : < %/K : Uo = 4 V, Ri 150 Ω, max. 50 ma Display : LCD-text display white/blue, 6.5 mm high with background lighting Display range : lines 16 characters each Refreshing time : 0.5s Output Panel case Dimensions Weight Connection Protection : SPDT < 50 V AC < 50 VA < A, < 300 V DC < 50 W < A : DIN 96x48 mm, Material PA6-GF; UL94V-0 : Front 96x48 mm, mounting depth 100 mm, : max. 390 g : Clamp terminals, mm² single wire, 1,5 mm² flexible wire, AWG14 : Front IP65, terminals IP0, finger safe acc. to German BGV A3 - -

3 Connection diagram Digital- or analog inputs 1-8 Digital inputs 9-0 Input 1 Input Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Input 9 Input 10 Input 11 Input 1 Input 13 Input 14 Input 15 Input 16 Input 17 Input 18 Input 19 Input 0 Extern. acknowledge +4 V DC GND Alarm relay Operation with voltagefree NO contact Supply voltage Operation with voltagefree NC contact Opeartion with external control voltage 4 V DC Analog inputs 0/ ma Note! If the analog signal is generated by an device with automatic burden recognition (current/voltage changeover), the analog output must be configured to mA (see page 7). Dimensions Seal Terminal position Panel cut-out acc. to DIN x48-3 -

4 GHM-Messtechnik GmbH Standort Martens Controls and indicators Field for additional text Infrared-sensor Up button Right button Left button Enter/acknowledge button Down button Description After switching on the supply the device initializes itself. The display shows the message SD9648 VX.X (X.X software-version). After the initializing procedure the device is located in the working level. Displayed messages can be paged and acknowledged with button. Pressing the button for more than seconds, activates the Configuration level Now all the parameters defining the function of the SD9648 can be programmed. After finishing the configuration or when no button was pushed for more than minutes, the program returns to the working level. Leaving the configuration level is possible at any time by pressing the button for more than seconds. Programming: Menu selection With every new display page menu points will be shown. The arrow º marks the actual menu point With button the next menu point will be selected With button the last menu point will be selected (Over the infrared remote control IR51 the menu items can also be selected by entering of the first letters.) With button the wanted menu will be called up. Parameter (e.g. input-no.; measuring range, alarm setpoint...) The wanted value will be entered with and. Arrows º» indicates that more than 3 characters can be displayed in the arrow direction. + = 1 parameter back Messages The wanted character position in the message will be selected with buttons and. The wanted character will be selected with buttons and. The entered character will be automatically stored with button and the cursor shows the next position. Special functions: + = Deletes character at the cursor position. Repeat function by pressing the button continuously. + = Blank 8 at the actual cursor position. Repeat function by pressing the button continuously. + = Line feed in the next line of the character set (see page 13). + = Simulation for controlling of the edited messages including the variables (see page 13)

5 Programming Notes to representation Parameter is only displayed when configurated Parameter is only displayed when feature is included (see order code) Note: All parameters can be called if they are not blocked by other programmed parameters and if they are available. Factory settings are shown in the display grafic. Menue display Operating level SD9648 StörmeldeDisplay press s min. Parameter display When first calling the configuration level. 1 Configuration level ºLanguage Standard text 1.1 deutsch ~ englisch Language of the operating instructions. Language ºStandard text.1 SD9648 StörmeldeDisplay Message if no error is present. Edit message, see page 4 and 13. continue page 6-5 -

6 GHM-Messtechnik GmbH Standort Martens Menue display Parameter display 3 ºMessages Copy messages Message programming for the inputs Devices with analog inputs have additional parameters. 3.1 Input: 1 (digital) Selection of input no. (depends on device type) 3. Input: 1 Selection of input no. (analog) 3.3 Measure range 1 Decimals: 1 Decimal selection, decimals 3.4 Measure range 1 Start: 0.0 Setting possible from digit Note! In case of change of a measuring range including analog variables in the message they must be adapted if necessary (see page 13). 3.5 Measure range 1 End: 100,0 3.6 Alarm function 1 OFF ~MIN ~MAX Selection possible from digit Switching performance for alarm output activation 3.7 Alarm 1 at: 0.0 Setting possible from start value... end value 3.8 Text 1 Edit message (see page 4 and 13). Note : Parameter programmning for input -0 are identical continue page 7-6 -

7 Menue display Parameter display 4 Messages ºCopy messages Copy mode. With same or similar messages the programming expenditure can be reduced with this function. 4.1 Copy message from 1 to Start- and destination address (identical with input no.). Note: With same start- and destination address the existing text will be deleted and with Text X substituted. X = Input-no. 4. Overwrite? Message N Only displayed if text is available at the destination address. Selection with Y or N. 4.3 Text 1 Edit message 5 ºInput type Alarm output Input identification. NO (H) or NC (L) with digital inputs and 0...0mA or 4...0mA with analog inputs 5.1 Input 1 3 º active H H H Enter H or L for digital inputs Input 1 3 º 0/4mA Enter 0 or 4 for analog inputs Input º active H H H Enter H or L for digital inputs continue page 8-7 -

8 GHM-Messtechnik GmbH Standort Martens Menue display Parameter display 6 Input type ºAlarm output Definition of the criteria for the identification of messages when simultaneous several alarms being present. 6.1 Text scrolling after 1s Input of the display time of a message of several lines (scrolling lines 1+/3+4) and/or change to other activated messages. 6. Auto scrolling OFF ~ON Automatical scrolling between several presented messages. Selection of ON jumps back to the menu selection. 6.3 Sort by First message Selection: First message The first message is permanently indicated. When manual scrolling is selected, every following messages are displayed in the queue of there indicated sequence Last message as before, however in reverse order. Priority The message with the highest priority is permanently indicated. At manual scrolling all further messages in the order of their priority, and/or with the same priority are sorted according to the last message mode. 6.4 Input 1 º Priority 1 1 Enter wanted priority. 1 = highest priority 9 = lowest priority continue page 9-8 -

9 Menue display Parameter display 7 ºAcknowledge Alarm relay Acknowledge function extern and/or intern possible 7.1 Acknowledge int. ~OFF ON Acknowledge intern with button. Note: only the just displayed and inactive message will be deleted. The internal buzzer can always be reset with every frontside button. 7. Acknowledge ext. ~OFF HIGH ~LOW 7.3 Quit relay Fault removed Acknowledge extern Selection OFF HIGH (NO) LOW (NC) Note: all inactive messages will be deleted Fault removed The relay can be quit if the belonging message is not present (like the message in the display). Fault pending The relay can be quit if the belonging message is present (like buzzer). 7.4 Input 1 3º Acknowl. N N N Selection Y activates the general acknowledge function for each input. 8 Acknowledge ºAlarm relay Switching function of the internal alarm relay. 8.1 Not energized ~Energized Switching performance Not energized Relay active at alarm Energized Relay inactive at alarm 8. Inputs 1 3º Relay N N N Selection Y activates the alarm relay for the indicated input continue page

10 GHM-Messtechnik GmbH Standort Martens Menue display Parameter display 9 ºBuzzer Alarm delay Buzzer function 9.1 Input 1 3º Buzzer N N N Selection Y activates the buzzer for the indicated input. The buzzer can quit with every frontside button 10 Buzzer ºAlarm delay Alarm delay function 10.1 Startup delay Delay 0s Startup delay of the device after power on from s. 10. Messages delay 0.0s Message delay after incoming alarm from s. 11 ºDate/time LCD-display Only with feature realtime clock 11.1 Date tt.mm.jjjj XX.XX.XXXX Configuration of the actual date. 11. Time hh:mm:ss XX:XX:XX Configuration of the actual time. continue page

11 Menue display Parameter display 1 Date/time ºLCD-display 1.1 Brightness Level: 7 Configuration of display brightness from Contrast Level: 5 Configuration of display contrast from ºRemote control Input lock 13.1 Device adress No: 7 Input of a device address within the range Itś possible to program 99 devices with the remote control IR51 without mutual influence. If the address 1 should be standard, the address no must not be changed by IR51. Every device react of each pressed button. 14 Remote control ºInput lock 14.1 Input lock OFF ~INT ~ALL INT Front key pad locked ALL as before, additional remote control is locked. Changing possible by pressing buttons or for seconds. continue page

12 GHM-Messtechnik GmbH Standort Martens Menue display Parameter display 15 ºFactory adjust (Exit) 15.1 Factory adjust Code=0 Code for factory settings. 16 Factory adjust º(Exit) End of programming Operating level SD9648 StörmeldeDisplay If no alarm is indicated the programmed Standard text (page 5) will be displayed. Error messages Parameter error -> please check If this messages appears, an configuration error is present. This message will be deleted by entering the Configuration level. The device is working with factory settings of this / these parameter(s). The function must be tested. If the same messages appears again, the device must be sent for factory repair. Write protected!! Input lock activated. See page

13 Character set: 8 = Blank A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z ä ö ü ß ñ ² ³ -1 $ - + ± * ^ [ ] ( ) < = >» ~ % # & α γ μ Ω π Σ / 8!? : ;,. _ 8 = 1 character forwards = 1 character backwards + = Line feed to the next line of the character set Variable Variable can inserted in arbitrary place into a message. Variable Function $c Number of the indicated message ( = input number) $a Number of indicated messages $o Priority of the indicated message (does not work at Standard text ) $n Recording counter of repeated messages on one input until acknowledge appears. (f 1Hz; nmax=99; if no. >99 flashes) [xxxx] All characters between [ ] are flashing (no combination with analog values possible) Only with feature real-time clock $h Actual hour (4h mode) $i Actual hour (1h mode) $p am / pm (1h mode) $m Actual minute $s Actual second $d Actual day $x Actual month $y Actual year $w Actual week day, letters identification εh, εi, εp, εm, εs, εd, εx, εy, εw as before, if messages appears (does not work at Standard text ) εt Additional time 1/100 seconds Only with feature analog inputs $1... $8 Shows permanent the analog value of the actual inputs By pressing the button after entering the input number, a number of substitute symbols is inserted automatically of the confirured measuring range into the text. This preemption can be adapted if necessary to the requirements. _ is a substitute symbol for a number. "," or "." indicates the decimal point. Maximally 5 numbers can be indicated, whereby already the variable name reserves $x already numbers and/or signs and 1 number. If the difference between measuring range end and measuring range start is more than 10000, the last number is kept automatically to "0". If are less digits reserved than necessary for the measuring range, this is marked in the simulation mode (buttons + at the same time) by flashing squares. ε1... ε8 Shows the analog value at input to the actual time of the presented signal (does not work at Standard text ) must be pressed. Reserved positions for the ana- After entering the variables (e.g. $x or εx) the button log variables will be inserted in the working mode. Example: $_,_ Reserved Positions for the analog-display of the measuring range from If reserved positions will be overwritten, the displayed value of the variable is incorrect. More examples next page

14 GHM-Messtechnik GmbH Standort Martens Variable function examples M Displaying of date and time in Standard text if no alarm appears.. M Displaying of date and time in messages at the time of the incoming signal. Identification possible for time and sequence of the signals. M Displaying of the actual analog measuring value in messages or Standard text. M Displaying of several analog values in the messages, at the time of incoming signal. This function allows to make an analysis for process problems possible. M Identification of the alarm input (identical with input number). Programming examples Line Actual date and time 1 $w, $d.$x.$y $h:$m:$s Line 1 Anzeige Mo, :3:30 Time at indicated input 1 εh:εm:εs Less water 3 Raw water :10:33 Less water Less water raw water Analog value (actual value) 1 Press 6: $1_,_ C Over temperature 1 Press C Over temperature Analog value (process value at time of incoming signal) 1 Press 6: ε1_,_ C Over temperature 1 Press C Over temperature Number of the indicated input 1 $C Door open 1 01 Door open Recording counter 1 Door open, $n Messages 1 Door open 33 Messages Flashing Text 1 [Attention!] No pressure 1 Attention! No pressure

15 - 15 -

16 GHM-Messtechnik GmbH Standort Martens Ordering code: 1. SD Inputs 1 0 digital inputs 1 digital + 8 analog inputs. Real-time clo 0 without 1 with clock 3. Supply voltage 0 30 V AC V AC 4 4 V AC 5 4V DC ±10 % ±10 % ±10 % ±15 % Hz Hz Hz 4. Options 00 without option 5. Additional text (appears in the field for additional text, max. text field 3 mm x 90 mm) 10/05-V1_