GW-LE8 Selective Call Audio Module for Open Voice Systems Use with: C-ML/A, LEM-1DL/C, LEF, LAF-C, or LDF Masters

Transcription

1 GW8 Selective Call Audio Module for Open Voice Systems Use with: CM/A, MD/C, F, AFC, or DF Masters INSTUCTIONS The GW8 is an audio module, used with other components to make up a selective calling audio door station. Panels from two to eight stations can be created. The entrance panel can selectively call and communicate with open voice inside master stations. Use any of the above listed master stations. Special Order Products GW8 w/ GWDP 8 Call ntrance Station *MODUA NTANC STATIONS ist of components for each entrance panel: Call Panel GW8 GWDP GWP GW Call Panel GW8 GWDP GWP GW Call Panel GW8 GWDP GWP GW GW 5 Call Panel GW8 GWDP GWP GWP GW 6 Call Panel GW8 GWDP GWP GWP GW 7 Call Panel GW8 GWDP GWP GWP GW GWP (x) 8 Call Panel GW8 GWDP GWP GW GW8 Terminal Definitions: D Common communication D Negative, common call signal Common Call signal (8 wires) Selective Callin and communication wires ( per button) COMPONNT MODS AND DSCIPTIONS Model Description GW8 Audio Module GWDP Audio Module Front Panel GWP Button Panel GWP Button Panel GWP Button Panel GWP Button Panel GW Panel Back Box GW Panel Back Box SMIFUSH AND SUFAC MOUNTING BOXS: Model Description GW00H Semiflush Mt. Hood for GW GW00HB Surface Mt. Hood for GW GW00H Semiflush Mt. Hood for GW GW00HB Surface Mt. Hood for GW Pg.

2 WIING DIAGAM: GW8 WITH GWP, USING CM/A MAST STATIONS Install jumper between D/D GW8 D D WIING DIAGAM: GWP SKK60 CM/A SKK60 CM/A SKK60 CM/A NOTS:. * Install bare wire end to "" terminal (DAKS contains two component modules).. Only components of the entrance panel that include wire connections are shown here.. See CM/A instructions for complete installation information. SKK60 CM/A GW8 WITH GWP & GWP, USING F MAST STATIONS GW8 F # F # F # F # F #5 F #6 D D GWP PSC emove / jumper on all masters. GWP YPA Blk NOTS:. In this example, the door station rings in on station # of each master station. It can be wired to any unused station number.. Only components of the entrance panel that include wire connections are shown here.. For complete wiring information, please see the F instructions. If additional master stations are to be installed in each office/suite, wire them per the standard instructions. Pg.

3 WIING DIAGAM: GW8 WITH GWP, USING MD/C MAST STATIONS Install jumper between D/D GW8 D D GWP PT0N MD/C PT0N MD/C PT0N MD/C PT0N NOTS:. Only components of the entrance panel that include wire connections are shown here.. For complete wiring information, please see the MD/C instructions. MD/C WIING DIAGAM: GW8 WITH GWP & GWP, USING F5 MAST STATIONS GW8 F5 # F5 # F5 # F5 # F5 #5 F5 #6 D D GWP PSC emove D/Djumper on all masters. GWP YPA Blk K K K NOTS:. In this example, the door station rings in on station # of each master station. It can be wired to any unused station number.. Only components of the entrance panel that include wire connections are shown here.. For complete wiring information, please see the standard F instructions. If additional master stations are to be installed in each office/suite, wire them per the standard instructions. K K K Pg.

4 Pg. WIING DIAGAM: GW8 WITH GWP, USING F MAST STATIONS WITH COMMON AND INDIVIDUA DOO STATIONS GW8 GWP F # F # F # D D D PSC K YPA Blk F # D D YPA Blk K K D K K YPA Blk YPA Blk K K K Blk YPA NOTS:. emove D/D jumper on all masters.. Only components of the entrance panel that include wire connections are shown here.. For complete wiring information, please see the standard F instructions. If additional master stations are to be installed in each office/suite, wire them per the standard instructions.

5 MOUNTING:. Cut appropriate sized mounting hole into wall.. Assemble and mount entrance panel GW /" GW /". Open a hole in the back box to pass cable through.. Mount the GW8 to the GWDP using the supplied screws.. Mount the components to the GW or GW frame.. Mount the frame to the back box. 5. eplace the two mounting screw covers. 8/8" /" Standard flush mount installation: Flush mount installation with weather hood: GW (Frame) GW (Frame) GW00H (Weather hood) GWDP GW8 (GW8 mounts to GWDP with supplied screws) GWP (Call switch panel) GW (Box) GWDP GW8 (GW8 mounts to GWDP with supplied screws) GWP (Call switch panel) GW (Box) Surface mount installation with weather hood: Filling in resident names: GW (Frame) GW00HB (Weather hood). emove protective cover using opener. (Opener included with GW and GW frames) Protective Cover GWDP GW8 (GW8 mounts to GWDP with supplied screws) GWP (Call switch panel) Opener Pg. 5

6 OPATION:. The entry station has multiple call buttons with an associated directory card. Press the button of the person you wish to call.. The master station(s) will ring an electronic call tone as long as the call button on the entrance station is being held. (A chime will be heard when using the CM/A room stations.). With CM/A and MD/C Master Stations: Press TAK button to answer the call. With F Master Stations: Select the station button with the lit D to answer. If the D has gone out (stays on for approx. 0 seconds), press the selector button assigned to the entry station.. At the inside station, press the TAK button to talk, and release to listen. The person at the entrance station speaks hands free. 5. When finished with the call, press the OFF button on the master station. 6. NOT: If the "Occupied" lamp is on, the system is in use. Wait until the D goes out, or determine if a master station has been left on unintentionally. SPCIFICATIONS: Source: Impedance: Communication: Calling: Wiring: Door elease Wiring: Wiring Distance: Provided from master station. CM/A: SKK60 or "C" batteries per master. MD/C: PT0N per master. F: PSC per system. 0 ohms Hands free at entry station. Pushtotalk at master station. CM/A: Stroke chime MD/C: Momentary call tone F: Momentary call tone and D, remaining lit for approx. 0 seconds CM/A: conductors homerun per station to entrance panel. MD/C: conductors homerun per station to entrance panel. F: common (,,, ) plus individual per sub, looped; or 5 conductors homerun to each master. Shielded cable is recommended. Use Aiphone #80 ( conductor) or 8 ( conductor) for max. 8 station wiring. conductors looped through stations to strike and strike power supply. CM/A: 5' with AWG; 590' with 8AWG. F/M: 650' with AWG;,600' with 8AWG. NOT: Only information concerning the GW8 is shown here. For complete wiring information, please see the appropriate system instructions. Aiphone Communication Systems 700 0th Ave. N.. Bellevue, WA (5) FAX (5) TO F TCHNICA SUPPOT: (800) TO F FAX IN: (800) 8765 MAI: techserv@aiphone.com Pg. 6 GW8 Instr. 00bkjd