Electrical Specifications

Transcription

1 Series 0 Watts C-Class Non-Isolated SXX06E Rev Page of 2 of Total Power: 0 Watts Input Voltage: Vdc No. of s: Single Special Features 0 A current rating Adjustable output voltage: V Excellent transient response Power enable ( pin model) Minimum airflow Small package Termination voltage capability RoHS compliant Electrical Specifications voltage See Note V setpoint accuracy 0.% trim resistors ±.0% Line regulation Low line to high line ± 0.2% Load regulation Full load to min. load ± 0.% Min./max. load 0 A/0 A Overshoot At turn-on 0.% max. Undershoot At turn-off 00 mv max. Ripple and noise Hz to 20 MHz See Note 20 mv Vin = V, Vout = 2. V Transient response See Notes, 2 30 mv max. deviation µs recovery to within regulation band Input Input voltage range Vdc Input current Minimum load Remote OFF 0 ma ma Input current (max.) See Note 3 0 lo max. Start-up time Power up 3 ms Remote ON/OFF 2 ms Safety UL, cul CAN/CSA 22.2 No. E3942 TÜV Product Service (EN6090) Certificate No. TBD CB Report and Certificate to IEC6090

2 General Efficiency (high input) Vin= V, Vo=2. V, lo=0 A 9% typical Switching frequency Fixed 620 khz Approvals and standards (pending) Material flammability Weight MTBF 2 40 C, 00% load Bellcore 332 EN6090 UL/cUL690 UL94V g (0.067 oz.) > 8,220,20 hours 2 of Coplanarity Surface mount models 0 µm Environmental Specifications Thermal performance See Note Protection Short-circuit Operating ambient, temperature Non-operating -40 C to +8 C -40 C to +2 C Hiccup, non-latching Recommended System Capacitance Input See Note 6 0 µf See Note 7 0 µf Ordering Information Power (Max.) Input Voltage OVP Voltage Current (Min.) Current (Max.) Efficiency (Typical) Regulation Line Load Model Number (3,) 0 W Vdc N/A V 0 A 0 A 94% ± 0.2% ± 0.% -00W0-VJ 0 W Vdc N/A V 0 A 0 A 94% ± 0.2% ± 0.% -00W0-HJ 0 W Vdc N/A V 0 A 0 A 94% ± 0.2% ± 0.% -00W0-SJ

3 Part Number System with Options 3 of Product Family Product Family LDO = C-Class LDO Series Rated Current Rated Current 0 = 0 Amp Performance Performance C = Cost Optimized Input Voltage Input Voltage 00 = V Number of Pins and Type of Number of Pins and Type of W = Pins and Wide Voltage Voltage 0 = V Mounting Option RoHS Compliance (8) LDO 0 C 00 W 0 V J Mounting Option V = Vertical H = Horizontal S = Surface RoHS Compliance J = Pb free (RoHS 6/6 compliant) Y = non PB-free (TSE /6 compliant) Voltage Adjustment of the LDO03C Series The ultra-wide output voltage trim range offers major advantages to users who select the LDO00C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of Vdc. When the LDO03C converter leaves the factory, the output has been adjusted to the default voltage of 0.9 V. Remote ON/OFF 4 V out LDO 0C Notes: Measured as per recommended system capacitance. See Application Note di/dt = 0 A/µs, Vin = Nom, Tc = 2 C, load change = 0.0 lo to full lo and full lo to External input fusing is recommended. 4 Additional part numbers may be available with different output voltages. Airflow dependent, 00 LFM minimum required. 6 No capacitors needed for ripple current capability. 7 No capacitors needed for stability. 8 NOTICE: the input voltage must be greater than the programmed output voltage. the max duty cycle is 9%. These non-isolated dc-dc modules are buck converters. V in GND C in 2 3 R trim (fortrim down) C out Figure : Standard Application Drawing R L O A D

4 Mechanical Drawings 4 of Vertical Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ± (± 0.76) 3 Places ± 0.00 (± 0.2). Enable. Trim MAX.062 REF.0 REF ± X.067 TYP SQ PINS TYP Figure 2: Vertical Mount Mechanical Drawing Horizontal Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ± (± 0.76) 3 Places ± 0.00 (± 0.2).4 MAX.40. Enable. Trim 6. Mech Pin REF.0 REF.02±.00 SQ PIN TYP 6 PLACES TYP.20 TYP 4X.067 TYP Figure 3: Horizontal Mount Mechanical Drawing

5 SXX06E Rev Page of 2 Surface Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ± (± 0.76) 3 Places ± 0.00 (± 0.2) 0.60 (6.) 0.03 (0.89) REF (0.4) - 00W0-0 (0.00) 0.00 (.27) 0.07 (.80) 0.38 (3.) 0.20 (.2). Enable. Trim 6. Mech Pin 7. Mech Pin (6.9) (8.6) (9.4) (3.3) 0.0 (.40) REF 0.2 (3.8) TYP (.7) REF (.02) REF Figure 4: Surface Mount Mechanical Drawing (0.64) REF Americas of 80 Van Allen Way Carlsbad, CA USA Telephone: Facsimile: Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY LX United Kingdom Telephone: +44 (0) Facsimile: +44 (0) Asia (HK) /F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: Facsimile: For global contact, visit: EmbeddedPower While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. 200 Emerson Electric Co.