Features. Regulated Converters. RS6 6 Watt. SIP8 Single and Dual Output. DC/DC Converter. Description. Selection Guide
|
|
- Anthony Ramsey
- 5 years ago
- Views:
Transcription
1 Features Regulated Converters Description Highest Power Density In SIP Package 1.6kVDC/1 Minute Isolation Efficiency Up To 88% -4 C To +75 C Operating Temperature Full Load EN695 And UL/EN (pending) CB Report Industry Standard Pinout The series offer very high power density (2.7W/cm³), wide input voltage range and an industrial operating temperature range of -4 C to +75 C without derating. High efficiency, tight regulation, 2kVDC isolation and remote on/off are just some of the characteristics of this advanced SIP8 6W converter which is ideal for high density power supply designs in demanding industrial applications. DC/DC Converter 6 Watt 3 SIP8 Single and Dual Output 3 YEAR w a r r a n t y Selection Guide Part nom. Input Output Output Efficiency max. Capacitive Number Voltage Voltage Current typ. (1) Load (2) [VDC] [VDC] [ma] [%] [µf] -53.3S S S S D 5 ±5 ±6 84 ±2-512D 5 ±12 ±25 87 ±9-515D 5 ±15 ±2 86 ± S S S S D 12 ±5 ±6 85 ±2-1212D 12 ±12 ±25 87 ±9-1215D 12 ±15 ±2 87 ± S S S S D 24 ±5 ±6 85 ±2-2412D 24 ±12 ±25 87 ±9-2415D 24 ±15 ±2 87 ± S S S S D 48 ±5 ±6 85 ±2-4812D 48 ±12 ±25 87 ±9-4815D 48 ±15 ±2 88 ±66 EN695-1 (pending) EN (pending) UL (pending) EN5522 compliant Notes: Note1: Efficiency tested at nominal input and full load at +25 C ambient. Note2: Max Cap Load tested at minimum input and constant resistor load. REV.: 1/216 ECO-1
2 BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Filter Input Voltage Range nom. Vin 5V 48V Input Surge Voltage 1 second max. nom. Vin= Quiescent Current Output Voltage Trimming Start-up time Under Voltage Lockout ON/OFF CTRL nom. Vin see calculation on next page nom. Vin= 5V nom. Vin= nom. Vin= nom. Vin= 48V 5V 2V 48V 5V 48V Trim up Trim down 4.5VDC 9VDC DC 36VDC Internal Operating Frequency -1% load 2kHz Minimum Load % 5VDC DC DC 48VDC 2ms 4.5VDC 2.7VDC 9VDC 7VDC DC 15VDC 36VDC 3VDC Capacitor type 9VDC DC 36VDC 75VDC 15VDC 25VDC 5VDC 1VDC 15mA 55mA 28mA 14mA +1% -8% Open 5V<Vr<1VDC Output Ripple and Noise (3) 2MHz BW 5mVp-p 75mVp-p Efficiency vs. Load 1 Notes: Note3: Measurements are made with a 1.µF MLCC across output (low ESR). -125S 1-245S 8 8 Efficiency [%] V 15V Efficiency [%] V 36V Output Load [A] Output Load [%] continued on next page ECO-2 REV.: 1/216
3 Output Voltage Trimming Trim UP Trim DOWN +Vout Vref R1 R2 R3 Trim -Vout R down Vref R1 R2 R3 Trim R up Vout 3.3V 5V 15V R kω 1 kω 38 kω 5 kω R2 1 kω R kω 39 kω 68 kω 68 kω Vref 1.24 V 2.5 V Trim Calculation R up = q a*r2 Vref r - RI3 = kω a = q r * R1 = kω DVout = Output Voltage Trim R2 - a DVout - Vref R up = trim up resistor R down = trim down resistor b*r1 R down = q r - R3 = kω b = q DVout - Vref r * R2 = kω a = trim up factor R1 - b Vref b = trim down factor Practical Example: Trim Up: Vout = 5V, DVout = 1% (5.5V), Vref= 2.5V 2.5V a = q r * 1kΩ = 8.33kΩ 5.5V - 2.5V R up = q 8.33kΩ * 1kΩ r - 39 = 11.kΩ 1kΩ kΩ -xx3.3s Trim up % Vout = Volts = KOhms -xx5s Trim up % Vout = Volts = KOhms -xx12s Trim up % Vout = Volts = KOhms -xx15s Trim up % Vout = Volts = KOhms continued on next page REV.: 1/216 ECO-3
4 Trim down: Vout = 5V, DVout = -8% (4.5V), Vref= 2.5V b = q 4.6V - 2.5V r * 1kΩ = 8.4kΩ 2.5V R down = q 8.4kΩ * 1kΩ r - 39kΩ = 13.5kΩ 1kΩ - 8.4kΩ -xx3.3s Vout = Volts = KOhms -xx5s Vout = Volts = KOhms -xx12s Vout = Volts = KOhms -xx15s Vout = Volts = KOhms REGULATIONS Parameter Condition Values Output Accuracy ±1% typ. Line Regulation low line to high line ±.2% typ. Load Regulation % to 1% load ±1% typ. Cross Regulation 25% to 1% load ±5% typ. Transient Response 25% load step change 5µs typ. Accuracy vs Load -125S -245S.5.2 Accuracy [ ] V 15V Accuracy [ ] V 36V Output Load [A] Output Load [A] ECO-4 REV.: 1/216
5 PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) below 1mW continuous, automatic revovery Over Load Protection (OLP) Isolation Voltage Isolation Capacitance Isolation Resistance Isolation Grade I/P to O/P 15% load, continuous, autmatic recovery 2kVDC / 1 second 1.6kVDC / 1 minute 11pF max. 1GΩ typ. Functional ENVIRONMENTAL Parameter Condition Value Operating Temperature Range (5) without derating (see graph) -4 C to +75 C Maximum Case Temperature Temperature Coefficient +15 C ±.2%/ C Operating Humidity non-condensing 5% - 95% RH max. Vibration MIL-STD-22G MTBF according to MIL-HDBK-217F +25 C 1776 x 1 3 hours Derating Graph (@ Chamber and natural convection) 1 Output Power [%] Safe Operating Area Ambient Temperature [ C] Notes: Note5: Derating Graph is referring to -55S. For more details, please contact our technical support service at TechsupportAT@recom-power.com. 12 SAFETY AND CERTIFICATIONS Certificate Type Report / File Number Standard Information Technology Equipment, General Requirements for Safety (LVD) PENDING EN695-1, 2nd Endition AM2, 213 Audio/video, information and communication technology equipment - Safety requirements (CB Scheme) RoHS 2.1 PENDING EN , 214 UL , 2nd Edition, 214 CAN/CSA C22.2 No , 214 RoHS-211/65/EU + AM-215/863 EMC Compliance Condition Standard / Criterion Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement continued on next page see filter suggestions EN5522, Class B REV.: 1/216 ECO-5
6 ESD Electrostatic discharge immunity test ±8kV Air Discharge, ±6kV Contact Discharge EN61-4-2, Criteria A Radiated, radio-frequency, electromagnetic field immunity test 1V/m EN61-4-3, Criteria A Fast Transient and Burst Immunity ±2kV EN61-4-4, Criteria A Surge Immunity ±1kV EN61-4-5, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields 1Vr.m.s EN61-4-6, Criteria A EMC Filtering - Suggestions for EN5522 Class A +Vin -Vin C1 C2 L1 LOAD Model C1 C2 L1-5xx 22µF 1µH -12xx N/A 2.2µH 4.7µF -24xx 6.8µH -48xx 2.2µF 2.2µF 1µH EMC Filtering - Suggestions for EN5522 Class B C7 +Vin C1 C2 C3 C4 C5 L1 L2 C6 LOAD -Vin C8 Model C1 C2 L1 C3 C4 L2 C5 C6 C7 C8-5xx 22µF 1µH N/A 1µF 1µF 47pF 1pF -12xx 1µF N/A 6.8µH N/A 2µH 4.7µF -24xx 4.7µF 1µH 4.7µF 4.7µF 33pF 22pF N/A -48xx 2.2µF 2.2µF 22µH 2.2µF 2.2µF 6µH 1µF 47pF 68pF Surge Protection Circuit according to EN61-4-5, Criteria A +Vin C surge D surge LOAD -Vin Input Voltage Csurge Dsurge max. Surge Voltage 5VDC DC DC 48VDC 1V, 22F E/Cap TVS (P4SMAJ15CA) N/A ±1kVDC ECO-6 REV.: 1/216
7 DIMENSION and PHYSICAL CHARACTERISTICS Parameter Type Value Material Package Dimension (LxWxH) Case Potting non conductive plastic (UL94V-) Epoxy (UL94V-) 21.8 x 9.2 x 11.1mm Package Weight 4.g Dimension Drawing (mm) embossed logo Marking Bottom View 7 x 2.54 = Recommended Footprint Details 1. Ø +.15/- Top View Pin Connections Pin # Single Dual 1 -Vin -Vin 2 +Vin +Vin 3 CTRL CTRL 5 Trim NC 6 +Vout +Vout 7 -Vout Com 8 NC -Vout NC= no connection Tolerance: xx.x= ±.5mm xx.xx= ±.25mm Pin dimension: ±.1mm Pin pitch: ±.25mm PACKAGING INFORMATION Packaging Dimension (LxWxH) tube 52. x 18.2 x 11.2mm Packaging Quantity 22pcs Storage Temperature Range -55 C to +125 C Storage Humidity non-condensing 95% RH max. The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. REV.: 1/216 ECO-7
High power density 3W Converter in SIP7 case. 3kVDC and 4kVDC Isolation Options
Features Unregulated Converters Description High power density 3W Converter in SIP7 case 3kVDC and 4kVDC Isolation Options Efficiency to 9% Certified to IEC/EN62368 The series of 3W high isolation DC/DC
More informationPinning (3) 4:1 Input Single or Dual. Notes: Note3: /X2 is without ON/OFF CTRL and without Output Voltage Trimming
Features Regulated Converters 4:1 wide input voltage range Compact size 1 x1 package Efficiency up to % Wide operating temperature from - C to +75 C without derating Continuous short circuit protection
More informationFeatures. Switching Regulator. 2.0 Amp SIP3 Single Output R-78B-2.0 R-78B DC/DC Converter
Features Switching Regulator Description Efficiency up to 96%, no need for heatsinks 2A continuous output current Vin up to 32V Vout: 1.2V - 15V Wide operating temperature - C to +7 C at full load Continuous
More informationNotes: Note1: Max. capacitive load is tested at nominal input voltage and full load. Single or Dual
Features Regulated Converters Description 6-Side Shielding External ON/OFF control 1.6kV Isolation UL/CSA/EN-695-1 Certified 2:1 Input Voltage Range Continuous Short Circuit Protection Efficiency up to
More informationNote1: Max. capacitive load is tested at nominal input and constant resistive load. RI3- _/_ Isolation (2) Single
Features Unregulated Converters 3 Watt in a SIP4 Package -3kVDC Isolation Efficiency up to 9% -4 C to + C Operating Temperature Range IEC/EN/UL69 (Pending) CB Report (Pending) Industry Standard Pinout
More informationNotes: Note3: without suffix, standard isolation voltage (1kVDC/1 second) with suffix /H, high isolation voltage (3kVDC/1 second)
Features Unregulated Converters Description 1W Power In SMD Package Pin Compatible With R1S -4 C To +1 C Operating Temperature @ Full Load high 3kVDC/1 Second or 1kVDC/1 Second Isolation IEC/EN/UL62368-1
More informationPackaging. nom. Output Voltage
Features Unregulated Converters 1W Power in SMD package Pin compatible with R1S series -40 C to +100 C operating temperature @ full load High 3kVDC/1 second or 1kVDC/1 second isolation IEC/EN/UL62368-1
More informationFeatures. Unregulated Converters. 1 Watt SIP6 Micro Size, Single and Dual Output RBM. RBM- / Protection (3) Single or Dual.
Features Unregulated Converters Micro size SIP 6 package Industry standard pinout Power sharing on dual output version 3kVDC/1s basic isolation Optional continuous short circuit protection Efficiency up
More informationFeatures. Unregulated Converters. R1SX/R1DX 1 Watt SMD Single & Dual Output R1_X- /_ -R. DC/DC Converter
Features Unregulated Converters Description 1W Power in SMD package Pin compatible with R1S/R1D series -4 C To +1 C Operating temperature @ full load High 3kVDC/1 second or 1kVDC/1 second isolation IEC/EN/UL62368
More informationFeatures. Unregulated Converters. R1SX/R1DX 1 Watt SMD Single & Dual Output R1_X- /_ -R. DC/DC Converter
Features Unregulated Converters Description 1W Power in SMD package Pin compatible with R1S/R1D series - C To + C Operating temperature @ full load High 3kVDC/1 second or 1kVDC/1 second isolation IEC/EN/UL62368-1
More information3kVDC or 4kVDC isolation Optional continuous short circuit protection UL94V-0 package material Efficiency up to 84% Suitable for IGBT applications
Features Unregulated Converters Description 3kVDC or 4kVDC isolation Optional continuous short circuit protection UL94V- package material Efficiency up to 84% Suitable for IGBT applications The RK and
More informationFeatures. Regulated Converter. 5 Watt DIP24 Single Output. Rxx-B R - B. DC/DC Converter
Features Regulated Converter High output voltage DIP24 converter Adjustable output voltage up to VDC Cascadable for output voltages up to VDC 3kVDC input/output isolation Remote voltage programming by
More informationFeatures. Switching Regulator. 0.5 Amp SIP3 Single Output R R DC/DC Converter
Features Switching Regulator Description Efficiency up to 97%, no need for heatsinks Pin-out compatible with LM78XX linears Very low profile 4.75V - 32V Wide input range Short circuit protection, thermal
More informationLoad (2) Single or Dual
Features Regulated Converter Reinforced insulation for 2VAC working voltage Clearance and creepage distance >8.mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout 4:
More informationFeatures. Regulated Converter RAC Watt Single Output. AC/DC Converter
Features Regulated Converter Description Wide input range 8-64VAC Standby mode optimized PSU (ENER Lot 6) Ultra-high efficiency over entire load range Operating temperature range: -4 C to +8 C Class II
More informationFeatures. Regulated Converters. RAC05-K 5 Watt 1 x 1 Single Output RAC05- SK. AC/DC Converter
Features Regulated Converters 5W Class II Power Supply in Compact 1 x 1 Package (High Power Density) Internal EMC Class B Filter UL/IEC/EN695-1 certified UL/IEC/EN62368-1 certified Electrical Protection
More informationFeatures. Regulated Converter. REM6 6 Watt 2:1 & 4:1 DIP24 Single and Dual. Output. DC/DC Converter
Features Regulated Converter Reinforced insulation for 250VAC working voltage Clearance and creepage distance: 8mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout
More informationOutput Current 1.2VDC 1.5VDC 1.5VDC 1.2VDC 1.5VDC 1.5VDC 0.65VDC. Vout=3.6VDC 180µA. Vout=1.8VDC, use E-cap 330µF Vout=3.3VDC and 3.6VDC.
Features Switching Regulator Description The is a DC/DC boost converter designed to run from single cell batteries. The input voltage range of.65v-3.3v means that alkaline, NiCd, NiMH, zinc-carbon or lithium
More informationNote1: Measured at nominal input voltage and full load Note2: Measured at minimum input voltage and constant resistive load
Features Regulated Converters Description :1 wide input voltage range 1.kV isolation UL certified Efficiency up to 88% Fixed operating frequency Six-Sided continuous shield No minimum load required The
More informationNote1: Efficiency is tested at nominal input and full load at +25 C ambient Note2: Max Cap Load is tested at nominal input and full resisitive load
Features Regulated Converter Description 4mW max. no load power consumption High efficiency up to 76% Isolated output 3kVAC / 1 min SCP, OVP protection Wide operating temperature range: -4 C to +85 C Universal
More informationLoad (2) Single or Dual
Features Regulated Converter Reinforced insulation for VAC working voltage Clearance and creepage distance >8.mm kvac I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout 4:
More informationFeatures. Regulated Converter. REM10 10 Watt. 2:1 & 4:1 DIP24 Single and Dual Output REM10- / DC/DC Converter
Features Regulated Converter Description Reinforced insulation for 250VAC working voltage Clearance and creepage distance: 8mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard
More informationFeatures. Regulated Converter. RAC02-SE/277 2 Watt Single Output RAC02- SE/277. AC/DC Converter
Features Regulated Converter Description 5mW max. no load power consumption Efficiency up to 76% Isolated output kvac / min SCP, OVP protection Wide operating temperature range: -4 C to +85 C Universal
More informationFeatures. Regulated Converter. RAC05-K/277 5 Watt Single Output RAC05- SK/277/W. AC/DC Converter
Features Regulated Converter Description Wide input range 85-5VAC Standby mode optimized (eco design Lot 6) High efficiency over the entire load range Operating temperature range: - C to + C Overvoltage
More informationFeatures. Regulated Converters. RAC01-C RAC02-C 1-2 Watt Single Output RAC0_- C. AC/DC Converter
Features Regulated Converters Description Compact low profile AC-DC power supply mw no load power consumption Class II power supply with kvac isolation Universal input voltage range (~VAC) Low output ripple/noise
More informationFeatures. Regulated Converter. RAC05-K 5 Watt 1 x 1. Single Output RAC05- SK. AC/DC Converter
Features Regulated Converter Description 5W Class II power supply in compact 1 x 1 Package (high power density) Internal EMC class B filter UL/IEC/EN695-1 certified UL/IEC/EN62368-1 certified Electrical
More informationEfficiency [%] 115VAC 230VAC. Parameter Condition Value. Line Regulation low line to high line ±0.5% max. Load Regulation 10% to 100% load ±0.5% max.
Features Regulated Converter Universal Input VAC 3W PCB Mount Package
More informationFeatures. Regulated Converter. RAC04-C/277 4 Watt Single and Dual Output RAC04- C/277 -_. AC/DC Converter
Features Regulated Converter Description mw max. no load power consumption High efficiency up to 79% Isolated Output 3.75kVAC / 1 minute SCP, OVP protection Wide operating temperature range: -4 C to +
More informationIEC/EN/UL60950 & CE certified, EN55032 Class B
Features Regulated Converter Universal input VAC 3W PCB mount package
More informationFeatures. Regulated Converter. RAC10-K/ Watt 2 x 1 Single and Dual Output RAC10- K/277. AC/DC Converter
Features Regulated Converter Description Wide input range 85-35Vac Full load temperature range: -4 C to +65 C Ultra-high efficiency over entire load range No external components necessary International
More informationParameter Condition Min. Typ. Max. Internal Input Filter 115VAC 230VAC 115VAC 230VAC. No load Power Consumption
Features Regulated Converter Universal input VAC 3W PCB mount package
More informationFeatures. Regulated Converter. RAC02-SE/277/W 2 Watt Single Output. RAC02- SE/277/W Wired. AC/DC Converter
Features Regulated Converter Description 35mW max. no load power consumption Efficiency up to 76% Isolated output 3kVAC / 1 minute SCP, OVP protection Wide operating temperature range: -4 C to +85 C Universal
More informationParameter Condition Min. Typ. Max. Internal Input Filter. refer to line derating graph on PA-4 115VAC 230VAC 115VAC 230VAC. No load Power Consumption
Features Regulated Converter Universal input 85-35VAC 3W PCB mount package
More informationFeatures. Switching Regulator. 0.5 Amp SIP3 Single Output R-78HB-0.5(L) DC/DC Converter
Features Switching Regulator Description Efficiency up to 96%, no heatsinks required Pin-out compatible with LM78XX linears Low profile (L/W/H=.5 x 8.5 x 7.5mm) High input voltage range, up to 7V Short
More informationFeatures. Regulated Converter RAC05- SK/C14. RAC 5 Watt Single Output RAC05-3.3SK/C14. AC/DC Converter
Features Regulated Converter Unique, patent-pending design Isolated power supply with integrated mains filter Packaged inside of line filter case Safe, touchable DC outputs Easy installation Worldwide
More informationFeatures. Switching Regulator. 0.5 Amp SIP3 Single Output R-78HB-0.5(L) R-78HB - /L. DC/DC Converter
Features Switching Regulator Description Efficiency up tpo 96%, no heatsinks required Pin-out compatible with LM78XX linears Low profile (L/W/H=.5 x 8.5 x 7.5mm) High input voltage range, up to 7V Short
More informationFeatures. Non Isolated Power Module ROF-78E ROF-78E - SMD-R. DC/DC Converter
Features Low profile 4.mm Low cost Wide input range (5V - 36V) Short circuit protection Casellated connections Description The is a switching regulator with a wide input voltage range, high effi ciency
More informationFeatures. Regulated Converters. RACM40 40 Watt Enclosed & Open Frame Case Style Single Output RACM40- S / - AC/DC Converter.
Features Regulated Converters Description Long 5 Year Warranty 2MOPP/250VAC Suitable for built in Class II Applications Wide Input Voltage Range (85-264VAC) Low Leakage Current (
More informationNote1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage.
Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Ribbed Case Style 22VDC Isolation Built-in EMC Filter, EN-522 Class B The RPP20 series
More informationFeatures. Power Module. 2 Amp Single Output RBB RBB DC/DC Converter
Features Power Module 1W buck/boost converter with up to 4A output Input voltage can be higher, lower or same as output voltage >9% efficiency from 1mA 3mA load 7µA standby power consumption Low profile,
More informationFeatures. Switching Regulator. 2,3,4 Amp SIP12 Vertical & Horizontal Single Output. R-7xxxP_D. R-7 x. DC/DC Converter
Features Switching Regulator Description Non-isolated Synchronous rectification design Adjustable output voltage 2, 3, 4Amp adjustable positive step down Integrated switching regulator Over load protection
More informationNote1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage.
Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Ribbed Case Style 22VDC Isolation Built-in EMC Filter, EN-522 Class B The RPP20 series
More informationFeatures. Regulated Converter RACM Watt Enclosed & Open Frame Case Style Single Output RACM65- S / - AC/DC Converter.
Features Regulated Converter Long 5 year warranty 2MOPP/250VAC Suitable for built in Class II applications Wide input voltage range (85-264VAC) Low leakage current (
More informationFeatures. LED Driver RACT Watt. TRIAC Dimmable. Single Output RACT AC/DC Converter
Features TRIAC Dimmable LED Driver Triac dimmable with leading or trailing edge dimmers Class II with SELV output (no earth required) Extra-large screw terminals and integrated cable clamps for easy installation
More informationFeatures. LED Driver RACT Watt. TRIAC Dimmable. Single Output RACT12- AC/DC Converter
Features TRIAC Dimmable LED Driver Triac dimmable with leading or trailing edge dimmers Class II with SELV output (no earth required) Extra-large screw terminals and integrated cable clamps for easy installation
More informationFeatures. Switching Regulator. 1-2 Amp SIP12 Vertical & Horizontal Single Output. R-6xxxP_D. R-6 x. DC/DC Converter
Features Switching Regulator Description Non-isolated Adjustable output voltage 1-2AMP adjustable positive step down integrated switching regulator Internal short circuit protection ON/OFF control (ground
More informationFeatures. Regulated Converters. RACM Watt Enclosed Case Style Single Output. RACM150- S/ _ Fan Option (1) Single. AC/DC Converter.
Features Regulated Converters Description Long 5 Year Warranty 2MOPP/250VAC Suitable for built in Class II Applications Wide Input Voltage Range (85-264VAC) Low Leakage Current (
More informationNote1: Max Cap Load is tested at minimum input and full resistive load. Connections (3) Case Style (1)
Features Regulated Converter Long 5 year warranty 2MOPP/2VAC Suitable for built in Class II applications Wide input voltage range (85-264VAC) Low leakage current (
More informationUL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit Protected Pinned
More informationNotes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 400VAC
Features DIN-Rail Description 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection
More informationNotes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 320VAC 360VAC 400VAC 400VAC
Features DIN-Rail 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection Parallel
More informationFeatures. Switching Regulator. 2,3,4,5 Amp SIP12 Vertical & Horizontal Single Output. R-5xxxPA_DA. R-5 xa. DC/DC Converter
Features Switching Regulator Description Non-isolated Synchronous rectification design Adjustable output voltage 2, 3, 4 & 5AMP adjustable positive step down integrated switching regulator Over load protection
More information15 W DC/DC CONVERTERS. SERIES DESCRIPTION Page. PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation
15 W DC/DC CONVERTERS SERIES DESCRIPTION Page PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation PC15WR4 4:1 Input Range 6 2 x 1 Metal Can Package 2kv Isolation CTC TECHNOLOGY CO.,LTD. DC /
More information18V 35V 65V 40A 60A 1.5W 1.2W ms 40ms. 20ms 20ms
Features DIN Rail Description Universal AC Input (85264VAC) Protections: SCP, OVP, OLP, OTP DC OK Indicator LED with Relay Contacts 5% (8W) peak load capacity Builtin active PFC,PF>,95 High effciency up
More informationFED30-48 S 05 - N HC Series Name Input Output Output Remote Control Assembly Option Voltage Quantity Voltage Option PART NUMBER STRUCTURE
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE FED30-48 S 05 - N HC Series Name Input Output Output Remote Control Assembly Option
More information500 ma DC-DC Step Down Converter P78G-Series
500 ma DC-DC Step Down Converter -Series Pin compatible to linear 78xx regulator (TO-220) Not isolated Efficiency up to 95 % Input voltage range up to 6 V Positive or negative output voltage possible Operating
More informationFor more information, please visit the product page. input voltage 1 range. output voltage
date 9/12/218 page 1 of 1 SERIES: V78E--SMT DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR FEATURES 1 A of output current efficiency up to SMT package industrial operating temp -~+ C designed to meet
More informationRPP20-W. Features ICE Technology* POWERLINE+ 20 Watt 4:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty
Features ICE Technology* Description 115 C Maximum Case Temperature -40 C Minimum Temp. UL Certified Built-in FCC/EN55022 Class B Filter 4:1 Wide Input Voltage Range Six Sided Shielded Enclosure Ribbed
More informationFED30-48 S 05 W - N HC Series Name Input Output Output Input Remote Control Assembly Option Voltage Quantity Voltage Range Option
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE FED30-48 S 05 W - N HC Series Name Input Output Output Input Remote Control Assembly
More informationRPP30. Features ICE Technology* POWERLINE+ 30 Watt 2:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty
Features ICE Technology* Description 115 C Maximum Case Temperature -40 C MinimumTemp. Built-in FCC/EN55022 Class B Filter 2:1 Wide Input Voltage Range Six Sided Shielded Enclosure Ribbed or Baseplate
More informationDC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output
THN 20WI Series Application Note DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output Pending Applications Wireless
More informationAdd suffix /W/X3 for wired version with both analogue and PWM dimming controls (six wires) (a)
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature
More informationSeries AM50E-NZ 50 Watt DC-DC Converter
FEATURES: Wide Input range 2:1 Input to Output Isolation of 1500 High Efficiency up to 93% Input Over Voltage and Under Voltage Lockout Remote On/Off Control Output OVP, OCP & SCP Trim Adjustment Operating
More informationOutput Full Load
SERIES DC-DC CONVERTER 2:1 & 4:1 WIDE INPUT RANGE UP TO 3.3 WATTS FEATURES REINFORCED INSULATION FOR 2VAC WORKING VOLTAGE CLEARANCE AND CREEPAGE DISTANCE :8.0mm/2MOPP 00VAC INPUT TO OUTPUT 2MOPP ISOLATION
More information4.59A 2.36A 6.8A 13A 3.85W 2.85W ms 21ms. 31ms 100ms 48Vout 49ms 100ms. 240mVp-p 480mVp-p C 48Vout 480mVp-p
Features DI Rail Description Universal AC Input (85264VAC) Protections: SCP, OVP, OP, OTP DC OK Indicator ED with Relay Contacts 15% (72W) peak load capacity Builtin active PFC, PF>.95 High effciency up
More informationhttp://www.mmtmachrone.com 96D SERIES FEATURES: 30W DIL PACKAGE Recognized By UL 60950-1 2:1 WIDE INPUT RANGE 100% BURNED IN HIGH EFFICIENCY UL 94V-0 PACKAGE MATERIAL CUSTOMIZED SOLUTIONS AVAILABLE RoHS
More information18V 35V 65V 40A 60A 1.5W 1.2W ms 40ms. 20ms 20ms. 100mVp-p 200mVp-p 120mVp-p 240mVp-p -25 C - 70 C 48Vout 240mVp-p
Features DIN Rail Universal AC Input (85) Protections: SCP, OVP, OLP, OTP DC OK Indicator LED with Relay Contacts 15% (18W) peak load capacity Builtin active PFC,PF>,95 High effciency up to 9.5% AC/DC
More informationhttp://www.mmtmachrone.com 93D SERIES FEATURES: 60W DIL PACKAGE INDUSTRY STANDARD PACKAGE 2:1 WIDE INPUT RANGE 100% BURNED IN HIGH EFFICIENCY UL94V-0 PACKAGE MATERIAL CUSTOM SOLUTIONS AVAILABLE RoHS COMPLIANT
More informationSeries AMSRL1-78JZ Up to 12 Watt DC-DC Switching Regulator
Click on Series name for product info on aimtec.com FEATURES: Picture Coming Soon Models Single output Model Input Voltage (V) Switching Regulator SMD Package Low Quiescent Current Efficiency Up To 95%
More information6S8W_3RP Series 6W - Dual/Single Output - Wide Input - Isolated & Regulated DC-DC Converter
6 Watt Highest power density in SIP8 package Low profile (L*W*H=21.8*9.2*11.1 mm) 2:1 wide input voltage range Isolation 3000VDC High Efficiency up to 88% Short circuit protection (SCP; (automatic recovery)
More informationRipple & Max. capacitive Output Current
0 Watts xxx Series Wide 4: Input Range Single Output Industry Standard /4 Brick -40 C to +0 C Operation 0 VDC Isolation Output Trim ±0% Remote On/Off Year Warranty Dimensions: QSC0:. x.4 x 0. (.9 x. x.
More informationC B. Models. Models 2MOPP
AC/DC Medical Power Supplies High power density 3" x 5" open frame medical power supply 450 Watt with forced air cooling 320 Watt convection cooled without derating up to 50 C Medical certification to
More informationDC/DC Converter K78_T-500R3 Series
Wide input voltage Non-isolated and Regulated Single Output RoHS FEATURES High efficiency up to 95% No-load input current as low as 0.2mA Operating ambient temperature range -40 to +85 Output short-circuit
More informationTPP 40 Series, 40 Watt. Order code Output voltage Output current max. Efficiency. max. screw terminal pin connector Vout 1 Vout 2 Vout 3
, Features High power density 40 W power supply (enclosed / open frame) 2 x MOPP Medical safety according to AAMI/ANSI ES 60601-1:2005(R) and IEC/EN 60601-1 3rd edition Ready to meet ErP directive, < 0.3
More informationDN03S/D Series DC/DC CONVERTER 2-3W, DIP-Package
DN03S/D Series DC/DC CONVERTER 2-3W, DIP-Package FEATURES DIP-24 Plastic Package Wide 2:1 Input Range Operating Temp.Range -40 to +85 C Overload Protection No Minimum Load Requirement Isolation voltage
More informationSpecifications ( typical at 25 C, nominal input voltage, rated output current unless otherwise specified )
Features Regulated Converters Description UL Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature Protected
More informationMLSR100 Series. High Efficiency, 1.0A Surface Mount, POL Switching Regulators. Key Features:
MLSR100 Series High Efficiency, 1.0A Surface Mount, POL Switching Regulators Electrical Specifications Specifi cations typical @ +25 C, nominal input voltage & rated output current, unless otherwise noted.
More informationMI2000ERW. Series. Miniature 1 x 1 20W, Ultra-Wide 2:1 Input DC/DC Con vert ers. Key Features:
MI2000ERW Miniature 1 x 1 20W, Ultra-Wide 2:1 Input DC/DC Con vert ers Key Features: 20W Output Power 2:1 Input Voltage Range Miniature 1 x 1 Case 1,500 VDC Isolation Meets CISPR 32/EN 55032 High Efficiency
More informationAdd suffix /SMD/OF for open frame version with SMD solderpins (/SMD/OF-R for Tape and Reel Packaging) (b)
Features Regulated Converters Description UL Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature Protected
More informationEfficiency (typ.) (Range) Load VDC VDC ma ma(typ.) ma(typ.) μf % MCWI05-12S
FEATURES Smallest Encapsulated 5W Ultracompact SIP8 Package Ultrawide 4 : 1 Input Voltage Range Fully Regulated Output Voltage I/O Isolation 1500 VDC Operating Ambient Temp. Range40 to 75 No Min. Requirement
More informationOutput Current Max (ma) Isolation (VDC)
Models Single output Model Input FEATURES: RoHS Compliant Operating Temperature - C to + 85 C High Efficiency up to 84% Continuous Short Circuit Protection Remote On / Off Control Wide 2:1 Input Range
More informationEfficiency (typ.) (Range) Load. Output Current Input Current Reflected Ripple
FEATURES Highest Power Density 1" x 1" x 0.4" Shielded Metal Package Ultra Wide 4:1 Input Range Excellent Efficiency up to % Operating Temp. Range - C to + C Optional Heatsink I/O-isolation Voltage 10VDC
More informationCV SERIES. 1.8 to 45 Watts VDC, VDC, 10-30VDC Input Ranges Adjustable Output Voltage Non-Isolated DC/DC Converters
DATASHEET CV SERIES 2.-.VDC, 4.-4VDC, 0-30VDC Input Ranges FEATURES Output Current up to 3A Output Power Range 2.-.VDC, 4.-4VDC, and 0-30VDC Input Voltage Ranges High Efficiency - 9% at 2VDC and Full Load
More information40 Watt TMF Single and Dual Series
Watt TMF Single and Dual Series Efficiency up to 91% 10VDC Isolation MTBF > 328,000 Hours 4:1 Wide Input Over Voltage Protection Short Circuit Protection Six Sided Shielding Remote On/Off Control RoHS
More informationTMT Series, 10 to 50 Watt. Order Code Output Power Output 1 PCB-Mount Chassis Mount max.
TMT Series, 10 to 50 Watt Features Ultra compact, fully encapsulated plastic case Single-, dual- and triple output models 2 package styles: - with screw terminal block for chassis mount - with solder pins
More informationSwitching Regulator. LMT78_1.0R Series Wide input, non-isolated & regulated, single output, SMD package
Efficiency up to 95 No need for heat sinks 1.0AMP SMD package Wide input voltage range (4.75V - 36V) Adjustable output voltage Remote ON/OFF control Short circuit protection (SCP), thermal shutdown Very
More informationPM24S/DR24S series 60W Single Output DC/DC Converter
FEATURES Efficiency up to 92% Wide input range, 9V-36V Package Dimension: Panel Mount: 100.0*56.0*19.0mm (3.94 * 2.20 *0.75 ) Din Rail: 118.6*67.1*23.5mm (4.67 *2.64 *0.93 ) Over voltage protection, hiccup
More informationDSA150 Series. xxx Series. 150 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125.
15 Watts xxx Series Ultra Slim Design 15% Peak Load for 3 seconds Ambient Operation from -1 C to +7 C High Efficiency Selectable Overload Characteristic Selectable Remote Inhibit or Enable 3 Year Warranty
More informationOrdercode Output Power Output 1 Output 2 Output 3 PCB-mounting Chassis mounting max. with solder pins with screw terminals
Features PCB Mounting with Solder Pins or Chassis Mounting with Screw Terminals Single, Dual and Triple Output Models Universal Input 8-2 VAC, 0 0 Hz EMI meets EN 022, Class B and FCC, Level B Low Ripple
More informationQAE100W SERIES QUARTER-BRICK DC-DC CONVERTER
SERIES QUARTER-BRICK DC-DC CONVERTER 4:1 ULTRA WIDE INPUT RANGE UP TO 90Watts FEATURES NO MINIMUM LOAD REQUIRED LOW STANDBY POWER CONSUMPTION SOFT-START 2250 INPUT TO OUTPUT BASIC INSULATION SAFETY MEETS
More informationWAF S 12 W - N S DR Series Name Input Output Output Input Remote Control Load Share Assembly Voltage Quantity Voltage Range Option Option Option
Railway Automation Datacom IPC Industry Measurement Telecom Charger Automobile Boat Medical PV PART NUMBER STRUCTURE WAF300-48 S 12 W - N S DR Series Name Input Output Output Input Remote Control Load
More informationPXD30-xxWS-xx-Single Output DC/DC Converters
PXD30-xxWS-xx-Single Output DC/DC Converters 9 to 36 Vdc and 18 to 75 Vdc input, 1.5 to 15 Vdc Single Output, 30W Applications Wireless Network Telecom / Datacom Industry Control System Measurement Semiconductor
More information25 Watt QMZ Single and Dual Series
Single and Dual Series Efficiency up to % 10 VDC Isolation 4:1 Ultra Wide Input Range Remote On/Off Control No Minimum Requirement Six Sided Shielding Trim RoHS Compliant CSA Approved Model Number Voltage
More information1.6W Gate Drive DC-DC Converter P2AGDC-Series
SIL7 Package Single / dual output 3000 Vrms isolation -40...105 C operating temperature range Efficiency up to 80 % Low couple I/O capacitance Model guide Type designation Input voltage range [V DC ] min.
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TIB Series, 80 480 W Slim profile, reduced module width High Power Factor up to 99% High efficiency up to 94% True back power immunity Low heat dissipation 150% peak current Automatic
More informationDC/DC Converter K78xx-500R2 Series
Converter K78xx-5R Series Wide input voltage, non-isolated & regulated single output Patent Protection RoHS FEATURES Efficiency up to 96% Operating temperature range: -4 to + Low ripple & noise Supporting
More informationOutput Current Input Current Load Regulation
PB01S/D series 1W DC/DC CONVERTER, SIP-Package FEATURES Efficiency up to 1% SIP Package with Industry Standard Pinout Package Dimension: 5V&12V Models: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 15V&24V
More informationSELECTION GUIDE. Nominal Input Voltage. Output Voltage
MTE1 Series SELECTION GUIDE FEATURES Single isolated output 1kVDC Isolation Efficiency up to 88% Power density 1.8W/cm 3 Wide temperature performance at full 1 Watt load, 4 C to 85 C UL 94V- Package material
More informationDC/DC Converter A_S-1WR2 & B_LS-1WR2 Series
1W, Fixed input voltage, isolated & unregulated dual/single output Patent Protection RoHS FEATURES Ultra Compact SIP package Operating temperature range: -4 to +15 High efficiency up to 8% Isolation voltage:
More informationWRA_CKS-1W & WRB_CKS-1W Series 1W, WIDE INPUT, ISOLATED & REGULATED DUAL/SINGLE OUTPUT SIP DC-DC CONVERTER
WRA_CKS-W & WRB_CKS-W Series W, WIDE INPUT, ISOLATED & REGULATED DUAL/SINGLE OUTPUT SIP DC-DC CONVERTER FEATURES 2: wide input range 500VDC Isolation Short circuit protection (automatic recovery) Remote
More information