Agilent 1200 Infinity Series

Transcription

1 Agilent 1200 Infinity Series Specification Compendium Agilent Technologies

2 Notices Agilent Technologies, Inc , 2013 No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and international copyright laws. Manual Part Number Rev. I Edition 02/2013 Printed in Germany Agilent Technologies Hewlett-Packard-Strasse Waldbronn This product may be used as a component of an in vitro diagnostic system if the system is registered with the appropriate authorities and complies with the relevant regulations. Otherwise, it is intended only for general laboratory use. Warranty The material contained in this document is provided as is, and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. Technology Licenses The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license. Restricted Rights Legend If software is for use in the performance of a U.S. Government prime contract or subcontract, Software is delivered and licensed as Commercial computer software as defined in DFAR (June 1995), or as a commercial item as defined in FAR 2.101(a) or as Restricted computer software as defined in FAR (June 1987) or any equivalent agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Agilent Technologies standard commercial license terms, and non-dod Departments and Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in FAR (c)(1-2) (June 1987). U.S. Government users will receive no greater than Limited Rights as defined in FAR (June 1987) or DFAR (b)(2) (November 1995), as applicable in any technical data. Safety Notices CAUTION A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met. WARNING A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met. Specification Compendium

3 Contents Contents 1 Pumps 5 Agilent 1290 Infinity Quaternary Pump (G4204A) 6 Agilent 1290 Infinity Binary Pump (G4220A) 9 Agilent 1290 Infinity Binary Pump (G4220B) 12 Agilent 1260 Infinity Binary Pump (G1312B) 15 Agilent 1260 Infinity Binary Pump VL (G1312C) 18 Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) 21 Agilent 1260 Infinity Quatenary Pump (G1311B) 23 Agilent 1260 Infinity Quaternary Pump VL (G1311C ) 26 Agilent 1260 Infinity Isocratic Pump (G1310B) 29 Agilent 1260 Infinity Preparative Pump (G1361A) 31 Agilent 1260 Infinity Capillary Pump (G1376A) 33 Agilent 1260 Infinity Nanoflow Pump (G2226A) 36 Agilent 1220 Infinity LC Pump 39 Agilent 218 Solvent Delivery Module 41 Agilent SD-1 Isocratic Solvent Delivery Module 44 2 Injectors and Fraction Collectors 47 Agilent 1290 Infinity Autosampler (G4226A) 48 Agilent 1290 Infinity LC Injector HTS (G4277A) 52 Agilent 1290 Infinity LC Injector HTC (G4278A) 56 Agilent 1290 Infinity Thermostat (G1330B) 60 Agilent 1260 Infinity Bio-inert High-Performance Autosampler (G5667A) 62 Agilent 1260 Infinity High Performance Autosampler (G1367E) 65 Agilent 1260 Infinity High Performance Micro Autosampler (G1377A) 68 Agilent 1260 Infinity Standard Autosampler (G1329B) 70 Agilent 1260 Infinity Preparative Autosampler (G2260A) 72 Agilent 1260 Infinity Dual-Loop Autosampler (G2258A) 74 Agilent 1260 Infinity Bio-inert Analytical-scale Fraction Collector (G5664A) 77 Agilent 1260 Infinity Preperative-scale Fraction Collector (G1364B) 80 Agilent 1260 Infinity Analytical-scale Fraction Collector (G1364C) 83 Agilent 1260 Infinity Micro-scale Fraction Collector (G1364D) 87 Agilent 1260 Infinity Chip Cube MS Interface (G4240A) 90 Agilent 1220 Infinity LC Autosampler 92 Agilent 410 Autosampler 94 Agilent 440 Fraction Collector 99 Specification Compendium 3

4 Contents 3 UV-Detectors 101 Agilent 1290 Infinity Variable Wavelength Detector (G1314E) 102 Agilent 1260 Infinity Variable Wavelength Detector (G1314F) 107 Agilent 1260 Infinity Variable Wavelength Detector VL+ (G1314C) 111 Agilent 1260 Infinity Variable Wavelength Detector VL (G1314B) 115 Agilent 1220 Infinity LC Variable Wavelength Detector 119 Agilent 1220 Infinity LC Diode Array Detector 123 Agilent 1290 Infinity Diode Array Detector (G4212A) 126 Agilent 1260 Infinity Diode Array Detector (G4212B) 131 Agilent 1260 Infinity Diode Array Detector VL+ (G1315C) 136 Agilent 1260 Infinity Diode Array Detector VL (G1315D) 141 Agilent 1260 Infinity Multiple Wavelength Detector (G1365C) 146 Agilent 1260 Infinity Multiple Wavelength Detector VL (G1365D) 151 Agilent 325 UV/VIS Dual Wavelength Detector Special Detectors 159 Agilent 1260 Infinity Fluorescence Detector (G1321B) 160 Agilent 1260 Infinity Refractive Index Detector (G1362A) 167 Agilent 1260 Infinity Evaporative Light Scattering Detector (G4260B) 170 Agilent 1290 Infinity Evaporative Light Scattering Detector (G4261B) Thermostatted Column Compartment 175 Agilent 1290 Infinity Thermostatted Column Compartment (G1316C) 176 Agilent 1260 Infinity Thermostatted Column Compartment (G1316A) 178 Agilent 1220 Infinity LC Column Oven Degasser 183 Agilent 1260 Infinity Micro Degasser (G1379B) 184 Agilent 1260 Infinity Standard Degasser (G1322A) 186 Agilent 1260 Infinity High Performance Degasser Module (G4225A) Valves 191 Agilent 1290 Infinity Flexible Cube (G4227A) 192 Agilent 1290 Infinity Valve Drive and Valve Heads (G1170A) Miscellaneous 201 Agilent 1200 Infinity Series Instant Pilot (G4208A) 202 Agilent 1260 Infinity Analytical SFC System 203 Agilent 1200 Infinity Series Universal Interface Box (G1390B) Specification Compendium

5 Specification Compendium 1 Pumps Agilent 1290 Infinity Quaternary Pump (G4204A) 6 Agilent 1290 Infinity Binary Pump (G4220A) 9 Agilent 1290 Infinity Binary Pump (G4220B) 12 Agilent 1260 Infinity Binary Pump (G1312B) 15 Agilent 1260 Infinity Binary Pump VL (G1312C) 18 Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) 21 Agilent 1260 Infinity Quatenary Pump (G1311B) 23 Agilent 1260 Infinity Quaternary Pump VL (G1311C ) 26 Agilent 1260 Infinity Isocratic Pump (G1310B) 29 Agilent 1260 Infinity Preparative Pump (G1361A) 31 Agilent 1260 Infinity Capillary Pump (G1376A) 33 Agilent 1260 Infinity Nanoflow Pump (G2226A) 36 Agilent 1220 Infinity LC Pump 39 Agilent 218 Solvent Delivery Module 41 Agilent SD-1 Isocratic Solvent Delivery Module 44 Agilent Technologies 5

6 Agilent 1290 Infinity Quaternary Pump (G4204A) Agilent 1290 Infinity Quaternary Pump (G4204A) Table 1 Physical Specifications Weight Dimensions ( height width depth) 15.2 kg (33.4 lbs) 200 x 345 x 435 mm (8 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 220 VA / 180 W / 615 BTU/h Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. 6 Specification Compendium

7 Pumps 1 Agilent 1290 Infinity Quaternary Pump (G4204A) Table 2 Performance specifications Hydraulic system Settable flow range Flow precision Dual pistons in series pump with proprietary servo-controlled variable stroke design, power transmission by ball screws, smooth motion control of pistons for active damping ml/min, in ml/min increments % RSD or 0.01 min SD, whatever is greater ( ml/min). Executed in 300 pl/st ep increments Based on retention time at constant room. Flow accuracy ±1 % or ± 10 µl/min, whatever is greater. Pumping degassed H 2 O at 10 MPa (100 bar) Maximum operating pressure Pressure pulsation Compressibility compensation Gradient formation Operating range up to 120 MPa (1200 bar), up to 2 ml/min, ramping down to 80 MPa (800 bar) up to 5mL/min. <1 % amplitude or < 0.5 MPa (5 bar), whatever is greater. Automatic, pre-defined, based on mobile phase selection. Low pressure quaternary mixing At 1 ml/min water Delay volume Standard configuration: <350 µl With optional V380 Jet Weaver: <500 µl Composition range Settable range: % Recommended range: 1 99 % or 5 µl/min per channel, whatever is greater. Composition precision <0.15 % RSD, or 0.02 min SD, whatever is greater (1 ml/min). Based on retention time at constant room Composition accuracy ±0.40 % absolute (1 99 % B, ml/min with water/caffeine tracer, 400 bar) Specification Compendium 7

8 1 Pumps Agilent 1290 Infinity Quaternary Pump (G4204A) Table 2 Performance specifications Integrated degassing unit Number of channels: 4 Internal volume per channel: 1.5 ml Control Local control Communications Safety and maintenance GLP features Housing Agilent ChemStation for LC (C or above) OpenLAB (A.04.04) Masshunter (B or above) Agilent Instant Pilot (G4208A) (B or above) Controller-area network (CAN), RS232C, APG remote: ready, start, stop and shutdown signals, LAN Extensive diagnostics, error detection and display through Agilent LabAdvisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable. 8 Specification Compendium

9 Agilent 1290 Infinity Binary Pump (G4220A) Pumps 1 Agilent 1290 Infinity Binary Pump (G4220A) Table 3 Physical Specifications Weight Dimensions (height width depth) 21.8 kg (48 lbs) 240 x 345 x 435 mm (9.3 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 350 VA / 270 W / 922 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 9

10 1 Pumps Agilent 1290 Infinity Binary Pump (G4220A) Table 4 Performance specifications Hydraulic system Settable flow range Flow precision Flow accuracy Pressure operating range Pressure pulsation Compressibility compensation Gradient formation Two dual pistons in series pumps with proprietary servo-controlled variable stroke design, power transmission by ball screws, smooth motion control of pistons for active damping. Setpoints ml/min, in ml/min increments % RSD or min SD, whatever is greater ( ml/min). ±1 % or 10 µl/min, whatever is greater. Operating range up to 120 MPa (1200 bar), up to 2 ml/min, 80 MPa (800 bar) at 5 ml/min. <1 % amplitude or < 0.5 MPa (5 bar), whatever is greater. Automatic, pre-defined, based on mobile phase selection. High pressure binary mixing. Executed in 300 pl/step increme nts Based on retention time at constant room. Pumping degassed H 2 O at 10 MPa (100 bar) At 1 ml/min water Delay volume Jet Weaver V35: <45 µl Jet Weaver V100: <75 µl JetWeaver generally recommended. For applications requiring lowest delay volumes, JetWeaver can be removed out of the flow path. Delay volume is then solely determined by the volume of the connection capillary. Composition range Settable range: % Recommended range: 1 99 % or 5 µl/min per channel, whatever is greater. 10 Specification Compendium

11 Pumps 1 Agilent 1290 Infinity Binary Pump (G4220A) Table 4 Performance specifications Composition precision Composition accuracy Solvent selection valve Integrated degassing unit Control Local control Communications Safety and maintenance GLP features Housing <0.15 % RSD, or 0.01 min SD, whatever is greater. ±0.35 % absolute (5 95 %, ml/min) Default Number of channels: 2 Internal volume per channel: 1.5 ml Agilent ChemStation for LC (B or above) EZChrom Elite (3.3.2 SP1 or above) OpenLAB (3.3.2 SP3) Masshunter (B SP1 or above) Agilent Instant Pilot (G4208A) (B or above) Controller-area network (CAN), RS232C, APG remote: ready, start, stop and shutdown signals, LAN Extensive diagnostics, error detection and display (through Agilent Lab Advisor), leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuos tracking of instrument usage in terms of purge valve switches and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable ml/min; based on retention time at constant room Water/caffeine tracer Standard part of the pump Specification Compendium 11

12 1 Pumps Agilent 1290 Infinity Binary Pump (G4220B) Agilent 1290 Infinity Binary Pump (G4220B) Table 5 Physical Specifications Weight Dimensions (height width depth) 21.8 kg (48 lbs) 240 x 345 x 435 mm (9.3 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 350 VA / 270 W / 922 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. 12 Specification Compendium

13 Pumps 1 Agilent 1290 Infinity Binary Pump (G4220B) Table 6 Performance specifications Hydraulic system Settable flow range Flow precision Flow accuracy Pressure operating range Pressure pulsation Compressibility compensation Gradient formation Two dual pistons in series pumps with proprietary servo-controlled variable stroke design, power transmission by ball screws, smooth motion control of pistons for active damping. Setpoints ml/min, in ml/min increments % RSD or min SD, whatever is greater ( ml/min). ±1 % or 10 µl/min, whatever is greater. Operating pressure range 120 MPa (1200 bar), up to 2 ml/min. <1 % amplitude or < 0.5 MPa (5 bar), whatever is greater. Automatic, pre-defined, based on mobile phase selection. High pressure binary mixing. Executed in 300 pl/step increme nts Based on retention time at constant room. Pumping degassed H 2 O at 10 MPa (100 bar) At 1 ml/min water Delay volume Jet Weaver V35: <45 µl Jet Weaver V100: <75 µl JetWeaver generally recommended. For applications requiring lowest delay volumes, JetWeaver can be removed out of the flow path. Delay volume is then solely determined by the volume of the connection capillary. Composition range Settable range: % Recommended range: 1 99 % or 5 µl/min per channel, whatever is greater. Composition precision <0.15 % RSD, or 0.01 min SD, whatever is greater ml/min; based on retention time at constant room Specification Compendium 13

14 1 Pumps Agilent 1290 Infinity Binary Pump (G4220B) Table 6 Performance specifications Composition accuracy Solvent selection valve Integrated degassing unit Control Local control Communications Safety and maintenance GLP features Housing ±0.35 % absolute (5 95 %, ml/min) Default Number of channels: 2 Internal volume per channel: 1.5 ml Agilent ChemStation for LC (B or above) EZChrom Elite (3.3.2 SP1 or above) OpenLAB (3.3.2 SP3) Masshunter (B SP1 or above) Agilent Instant Pilot (G4208A) (B or above) Controller-area network (CAN), RS232C, APG remote: ready, start, stop and shutdown signals, LAN Extensive diagnostics, error detection and display (through Agilent Lab Advisor), leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuos tracking of instrument usage in terms of purge valve switches and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable. Water/caffeine tracer Standard part of the pump 14 Specification Compendium

15 Agilent 1260 Infinity Binary Pump (G1312B) Pumps 1 Agilent 1260 Infinity Binary Pump (G1312B) Table 7 Physical Specifications Weight Dimensions ( height width depth) 15.5 kg (34 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 220 VA, 74 W / 253 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 15

16 1 Pumps Agilent 1260 Infinity Binary Pump (G1312B) Table 8 Performance Specifications of the Agilent 1260 Infinity Binary Pump (G1312B) Hydraulic system Setable flow range Flow range Flow precision Two dual piston in series pumps with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons Set points ml/min, in ml/min increments ml/min 0.07 % RSD or 0.02 min SD, whatever is greater based on retention time at constant room Flow accuracy ± 1 % or 10 µl/min, what ever is greater pumping degassed H 2 O at 10 MPa (100 bar) Pressure operating range Operating range 0 60 MPa (0 600 bar, psi) up to 5 ml/min Pressure pulsation < 2 % amplitude (typically < 1.3 %), or < 0.3 MPa (3 bar), whatever is greater, at 1 ml/min isopropanol, at all pressures > 1MPa (10bar, 147psi) Low delay volume configuration: < 5 % amplitude (typically < 2 %) Compressibility compensation Recommended ph range Gradient formation Delay volume Pre-defined, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel High-pressure binary mixing Standard delay volume configuration: µl, (includes 400 µl mixer), dependent on back pressure Low delay volume configuration: 120 µl measured with water at 1 ml/min (water/caffeine tracer) Composition range settable range: % recommended range: 1 99 % or 5 µl/min per channel, whatever is greater 16 Specification Compendium

17 Pumps 1 Agilent 1260 Infinity Binary Pump (G1312B) Table 8 Performance Specifications of the Agilent 1260 Infinity Binary Pump (G1312B) Composition precision Composition accuracy Control < 0.15 % RSD or < 0.04 min SD whatever is greater ± 0.35 % absolute, at 2 ml/min, at 10 MPa (100 bar) Agilent control software (e.g. ChemStation, EZChrom, OL, MassHunter) at 0.2 and 1 ml/min; based on retention time at constant room (water/caffeine tracer) Local control Agilent Instant Pilot Revision B or above Analog output Communications Safety and maintenance GLP features Housing For pressure monitoring, 1.33 mv/bar, one output Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors All materials are recyclable NOTE For use with flow rates below 500 µl/min or for use without damper and mixer a vacuum degasser is required. All specification measurements are done with degassed solvents. Specification Compendium 17

18 1 Pumps Agilent 1260 Infinity Binary Pump VL (G1312C) Agilent 1260 Infinity Binary Pump VL (G1312C) Table 9 Physical Specifications Weight Dimensions (height width depth) 15.5 kg (34 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 220 VA, 74 W / 253 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. 18 Specification Compendium

19 Pumps 1 Agilent 1260 Infinity Binary Pump VL (G1312C) Table 10 Performance Specification Agilent 1260 Infinity Binary Pump VL (G1312C) Hydraulic system Setable flow range Flow range Flow precision Flow accuracy Pressure operating range Two dual piston in series pumps with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons Set points ml/min, in ml/min increments ml/min 0.07 % RSD, or 0.02 min SD whatever is greater, based on retention time at constant room ±1 % or 10 µl/min whatever is greater, pumping degassed H 2 O at 10 MPa (100 bar) Operating range up to 40 MPa (400 bar, 5880 psi) up to 5 ml/min Pressure pulsation < 2 % amplitude (typically < 1.3 %), or < 0.3 MPa (3 bar) whatever is greater, at 1 ml/min isopropanol, at all pressures > 1MPa (10bar, 147psi) Compressibility compensation Recommended ph range Gradient formation Delay volume User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel High-pressure binary mixing µl (includes 400 µl mixer), dependent on back pressure Composition range settable range: % recommended range: 1 99 % or 5 µl/min per channel, whatever is greater Specification Compendium 19

20 1 Pumps Agilent 1260 Infinity Binary Pump VL (G1312C) Table 10 Performance Specification Agilent 1260 Infinity Binary Pump VL (G1312C) Composition precision < 0.15 % RSD or < 0.04 min SD, whatever is greater, at 0.2 and 1 ml/min; based on retention time at constant room Composition accuracy ± 0.5 % absolute (water/caffeine tracer) Control Local control Analog output Communications Safety and maintenance GLP features Housing Agilent control software (e.g. ChemStation, EZChrom, OL, MassHunter) Agilent Instant Pilot For pressure monitoring, 2 mv/bar, one output Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display through Agilent LabAdvisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors All materials are recyclable NOTE For use with flow rates below 500 µl/min a vacuum degasser is required. 20 Specification Compendium

21 Pumps 1 Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) Table 11 Physical Specifications Weight Dimensions (height width depth) 14.5 kg (32 lbs) 180 x 345 x 435 mm (7.0 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 180 VA, 110W / 375 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 21

22 1 Pumps Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) Table 12 Type Specifications - Agilent 1260 Infinity Bio-inert Quaternary Pump (G5611A) Specifications Hydraulic system Setable flow range Recommended flow range Flow precision Flow accuracy Pressure Pressure pulsation Compressibility compensation Dual-piston in-series pump with proprietary servo-controlled variable-stroke drive, floating pistons and active inlet valve, integrated 4-channel degassing unit ml/min, in ml/min increments ml/min < 0.07 % RSD, or < 0.02 min SD whichever is the greater, based on retention time at constant room ± 1 % or 10 µl/min whichever is the greater Operating range up to 60 MPa (600 bar, 8700 psi) up to 5 ml/min Operating range up to 20 MPa (200 bar, 2950 psi) up to 10 ml/min < 2 % amplitude (typically < 1.3 %), at 1 ml/min isopropanol, at all pressures > 1 MPa (10 bar) User-selectable, based on mobile phase compressibility Recommended ph range 1 13, short term 14 1 Gradient formation Composition range Composition precision Communications Materials in flow path Active seal wash Low pressure quaternary mixing/gradient capability using proprietary high-speed proportioning valve. Delay volume µl, dependent on back pressure % or %, user selectable < 0.2 % RSD, at 0.2 and 1 ml/min Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Titanium, Gold, Platin-Iridium, Sapphire, PEEK, PTFE Included 1 For solvent compatibility, refer to section "Solvent information for parts of the 1260 Infinity Bio-inert LC system" in the manual 22 Specification Compendium

23 Agilent 1260 Infinity Quatenary Pump (G1311B) Pumps 1 Agilent 1260 Infinity Quatenary Pump (G1311B) Table 13 Physical Specifications Weight Dimensions (height width depth) 14.5 kg (32 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 180 VA, 110W / 375 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 23

24 1 Pumps Agilent 1260 Infinity Quatenary Pump (G1311B) Table 14 Type Performance Specifications Agilent 1260 Infinity Quaternary Pump (G1311B) Specification Hydraulic system Setable flow range Flow range Flow precision Flow accuracy Pressure operating range Pressure pulsation Compressibility compensation Recommended ph range Gradient formation Delay volume Composition range Composition precision Integrated degassing unit Control Local control Analog output Dual piston in series pump with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons Set points ml/min, in ml/min increments ml/min 0.07 % RSD, or 0.02 min SD whatever is greater, based on retention time at constant room ± 1 % or 10 µl/min whatever is greater, pumping degassed H 2 O at 10 MPa (100 bar) Operating range up to 60 MPa (600 bar, 8700 psi) up to 5 ml/min Operating range up to 20 MPa (200 bar, 2950 psi) up to 10 ml/min < 2 % amplitude (typically < 1.3 %), or < 0.3 MPa (3 bar, 44 psi), whatever is greater, at 1 ml/min isopropanol, at all pressures > 1 MPa (10 bar, 145 psi) User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel Low pressure quaternary mixing/gradient capability using proprietary high-speed proportioning valve µl, dependent on back pressure; measured with water at 1 ml/min (water/caffeine tracer) 0-95 % or %, user selectable < 0.2 % RSD or < 0.04 min SD, whatever is greater, at 1 ml/min; based on retention time at constant room Number of channels: 4 Internal volume per channel: 1.5 ml Agilent control software (e.g. ChemStation, EZChrom, OL, MassHunter) Agilent Instant Pilot For pressure monitoring, 2 mv/bar, one output 24 Specification Compendium

25 Pumps 1 Agilent 1260 Infinity Quatenary Pump (G1311B) Table 14 Performance Specifications Agilent 1260 Infinity Quaternary Pump (G1311B) Communications Safety and maintenance GLP features Housing Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display through Agilent LabAdvisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors All materials are recyclable NOTE For use with flow rates below 500 µl/min a vacuum degasser is required. Specification Compendium 25

26 1 Pumps Agilent 1260 Infinity Quaternary Pump VL (G1311C ) Agilent 1260 Infinity Quaternary Pump VL (G1311C ) Table 15 Physical Specifications Weight Dimensions (height width depth) 14.5 kg (32 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 180 VA, 110W / 375 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. 26 Specification Compendium

27 Pumps 1 Agilent 1260 Infinity Quaternary Pump VL (G1311C ) Table 16 Type Performance Specification Agilent 1260 Infinity Quaternary Pump VL (G1311C) Specification Hydraulic system Setable flow range Flow range Flow precision Flow accuracy Pressure operating range Pressure pulsation Compressibility compensation Recommended ph range Gradient formation Delay volume Composition range Composition precision Integrated degassing unit Control Local control Analog output Dual piston in series pump with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons Set points ml/min, in ml/min increments ml/min 0.07 % RSD, or 0.02 min SD whatever is greater, based on retention time at constant room ± 1 % or 10 µl/min whatever is greater, pumping degassed H 2 O at 10 MPa (100 bar) Operating range up to 40 MPa (400 bar, 5880 psi) up to 5 ml/min Operating range up to 20 MPa (200 bar, 2950 psi) up to 10 ml/min < 2 % amplitude (typically < 1.0 %), or < 0.3 MPa (3 bar, 44 psi), whatever is greater, at 1 ml/min isopropanol, at all pressures > 1 MPa (10 bar, 145 psi) User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel Low pressure quaternary mixing/gradient capability using proprietary high-speed proportioning valve µl, dependent on back pressure; measured with water at 1 ml/min (water/caffeine tracer) 0 95 % or %, user selectable < 0.2 % RSD or < 0.04 min SD, whatever is greater, at 1 ml/min; based on retention time at constant room Number of channels: 4 Internal volume per channel: 1.5 ml Agilent control software (e.g. ChemStation, EZChrom, OL, MassHunter) Agilent Instant Pilot For pressure monitoring, 2 mv/bar, one output Specification Compendium 27

28 1 Pumps Agilent 1260 Infinity Quaternary Pump VL (G1311C ) Table 16 Performance Specification Agilent 1260 Infinity Quaternary Pump VL (G1311C) Communications Safety and maintenance GLP features Housing Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display through Agilent LabAdvisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors All materials are recyclable 28 Specification Compendium

29 Agilent 1260 Infinity Isocratic Pump (G1310B) Pumps 1 Agilent 1260 Infinity Isocratic Pump (G1310B) Table 17 Physical Specifications Weight Dimensions (height width depth) 11 kg (25 lbs) 180 x 345 x 435 mm (7.0 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 180 VA, 55 W / 188 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 29

30 1 Pumps Agilent 1260 Infinity Isocratic Pump (G1310B) Table 18 Type Performance Specification Agilent 1260 Infinity Isocratic Pump (G1310B) Specification Hydraulic system Setable flow range Flow range Flow precision Flow accuracy Pressure operating range Pressure pulsation Compressibility compensation Control Local control Analog output Communications Safety and maintenance GLP features Housing Dual piston in series pump with servo-controlled variable stroke drive, power transmission by gears and ball screws, floating pistons Set points ml/min, in ml/min increments ml/min 0.07 % RSD, or 0.02 min SD whatever is greater, based on retention time at constant room ±1 % or 10 µl/min whatever is greater, pumping degassed H 2 O at 10 MPa (100 bar) Operating range up to 60 MPa (600 bar, 8700 psi) up to 5 ml/min Operating range up to 20 MPa (200 bar, 2950 psi) up to 10 ml/min < 2 % amplitude (typically < 1.3 %), or < 0.3 MPa (3 bar), whatever is greater, at 1 ml/min isopropanol, at all pressures > 1 MPa (10 bar, 147 psi) User-selectable, based on mobile phase compressibility Agilent control software (e.g. ChemStation, EZChrom, OL, MassHunter) Agilent Instant Pilot For pressure monitoring, 1.33 mv/bar, one output Controller-area network (CAN), RS-232C, APG remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display through Agilent LabAdvisor, leak detection, safe leak handling, leak output signal for shutdown of the pumping system. Low voltage in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with pre-defined and user settable limits and feedback messages. Electronic records of maintenance and errors All materials are recyclable NOTE For use with flow rates below 500 µl/min a vacuum degasser is required. 30 Specification Compendium

31 Agilent 1260 Infinity Preparative Pump (G1361A) Pumps 1 Agilent 1260 Infinity Preparative Pump (G1361A) Table 19 Physical Specifications Weight Dimensions (height width depth) 15.0 kg (33 lbs) 200 x 345 x 440 mm (8 x 13.5 x 18) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 250 VA / 210 W / 717 BTU Maximum Ambient operating Ambient non-operating 4 40 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 31

32 1 Pumps Agilent 1260 Infinity Preparative Pump (G1361A) Table 20 Type Performance Specification Agilent 1260 Infinity Preparative Pump Specification Hydraulic system Settable flow range Recommended flow range Flow precision Pressure range Compressibility compensation Recommended ph range Control and data evaluation Communications Safety and maintenance GLP features Housing Dual pistons in parallel ml/min ml/min < 0.5 % RSD bar (5880 psi) system pressure User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel Agilent ChemStation for LC and LC/MS Controller-area network (CAN), RS-232, APG Remote: ready, start, stop and shut-down signals, CAN-DC OUT, LAN optional Extensive diagnostics, error detection and display (through Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with user-settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable. 32 Specification Compendium

33 Agilent 1260 Infinity Capillary Pump (G1376A) Pumps 1 Agilent 1260 Infinity Capillary Pump (G1376A) Table 21 Physical Specifications Weight Dimensions (height width depth) 17 kg (38 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 220 VA / 75 W / 256 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 33

34 1 Pumps Agilent 1260 Infinity Capillary Pump (G1376A) Table 22 Type Performance Specification Agilent 1260 Infinity Capillary Pump (G1376A) Specification Hydraulic system Settable column flow range Recommended column flow range Column flow precision Optimum composition range Two independent pump channels, each with two pistons in series. One proprietary servo-controlled variable stroke drive per channel. Floating pistons, active inlet valves, solvent selection valves (two solvents per pump channel), electronic flow control for flow rates up to 100 µl/min µl/min µl/min (with the extended flow range kit) µl/min (with the electronic flow control bypassed) 1 20 µl/min µl/min (with extended flow range kit) ml/min (with the electronic flow sensor bypassed) < 0.7 % RSD or 0.03 % SD (typically 0.4 % RSD or 0.02 min SD), at 10 µl/min and 50 µl/min column flow (based on RT, default setting) 1 99 % or 5 µl/min per channel (primary flow), whatever is greater Composition precision < 0.2 % SD, at 10 µl/min(20 µl flow sensor), 50 µl/min (100 µl flow sensor), minimum primary flow/pump channel is 5 µl/min, primary flow µl/min Delay volume Pressure range Compressibility compensation Recommended ph range Typically 3 µl from the electronic flow control to the pump outlet for flow rates up to 20 µl/min Typically 12 µl from the electronic flow control to the pump outlet for flow rates up to 100 µl/min For flow rates up to 100 µl/min and electronic flow control active: primary flow path µl without mixer, µl with mixer (system pressure dependant) Typically µl (system pressure dependent) without mixer for flow rates up to 2.5 ml/min (Mixer delay volume 420 µl) bar (5880 psi) system pressure User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel. Upper ph range is limited by fused silica capillaries. 34 Specification Compendium

35 Pumps 1 Agilent 1260 Infinity Capillary Pump (G1376A) Table 22 Type Performance Specification Agilent 1260 Infinity Capillary Pump (G1376A) Specification Control and data evaluation Analog output Communications Safety and maintenance GLP features Housing Agilent Control Software (Chemstation, EZ-Chrom, OL, etc.) For pressure monitoring, 2 mv/bar, one output Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display (though Instant Pilot and Data System), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with user-settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable. Specification Compendium 35

36 1 Pumps Agilent 1260 Infinity Nanoflow Pump (G2226A) Agilent 1260 Infinity Nanoflow Pump (G2226A) Table 23 Physical Specifications Weight Dimensions (height width depth) 17 kg (38 lbs) 180 x 345 x 435 mm (7 x 13.5 x 17 inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 220 VA / 75 W / 256 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. 36 Specification Compendium

37 Pumps 1 Agilent 1260 Infinity Nanoflow Pump (G2226A) Table 24 Type Performance Specification Agilent 1260 Infinity Nano Pump (G2226A) Specification Hydraulic system Settable column flow range Recommended column flow range Optimum composition range Composition precision Delay volume Pressure range Compressibility compensation Recommended ph range Control and data evaluation Analog output Communications Safety and maintenance Two independent pump channels, each with two pistons in series. One proprietary servo-controlled variable stroke drive per channel. Floating pistons, active inlet valves, solvent selection valves (two solvents per pump channel), electronic flow control for flow rates up to 4 µl/min µl/min µl/min 1 99 %or 5 µl/minper channel (primary flow), whatever is greater < 0.2 %SD, at 500 nl/min, minimum primary flow/pump channel is 5 µl/min, primary flow µl/min Typically 300 nlfrom the electronic flow control to the pump outlet For flow rates up to 4 µl/minand electronic flow control active: primary flow path µl; system pressure dependent (default settings; calculated volume) Typically µl(system pressure dependent) for flow rates up to 2.5 ml/min. (default settings; calculated volume) bar( 5880 psi) system pressure User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel. Upper ph range is limited by fused silica capillaries. Agilent Control Software (ChemStation, EZ-Chrom Elite, OpenLAB CDS, etc.) For pressure monitoring, 2 mv/bar, one output Controller-area network (CAN), RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Extensive diagnostics, error detection and display (though Instant Pilot and Data System), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Specification Compendium 37

38 1 Pumps Agilent 1260 Infinity Nanoflow Pump (G2226A) Table 24 Type Performance Specification Agilent 1260 Infinity Nano Pump (G2226A) Specification GLP features Housing Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of seal wear and volume of pumped mobile phase with user-settable limits and feedback messages. Electronic records of maintenance and errors. All materials recyclable. 38 Specification Compendium

39 Pumps 1 Agilent 1220 Infinity LC Pump Agilent 1220 Infinity LC Pump Table 25 Physical Specifications Weight Dimensions (height width depth) 30 kg (66 lbs) mm ( inches) Line voltage VAC, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 240 VA / 210 W / 717 BTU Maximum Ambient operating Ambient non-operating 4 55 C ( F) C ( F) Humidity < 95 % r.h. at 40 C (104 F) Non-condensing Operating altitude Up to 2000 m (6562 ft) Non-operating altitude Up to 4600 m (15091 ft) For storing the module Safety standards: IEC, CSA, UL Installation category II, Pollution degree 2 For indoor use only. Specification Compendium 39

40 1 Pumps Agilent 1220 Infinity LC Pump Table 26 Type Performance Specifications Agilent 1220 Infinity LC Pump Specification Hydraulic system Settable flow range Flow range Flow precision Dual plunger in series pump with proprietary servo-controlled variable stroke drive, floating plungers and passive inlet valve ml/min, in ml/min increments ml/min 0.07 % RSD, or < 0.02 min SD whatever is greater, based on retention time at constant room Flow accuracy ± 1 % or 10 µl/min whatever is greater; degassed H 2 O, bar, 1mL/min, at constant ambient Pressure Pressure pulsation Compressibility compensation Recommended ph range Gradient formation (optional) Delay volume Composition range Composition precision Operating range 0 60 MPa (0 600 bar, psi) up to 5mL/min Operating range 0 20 MPa (0 200 bar, psi) up to 10 ml/min < 2 % amplitude (typically < 1.3 %), at 1 ml/min isopropanol, at all pressures > 1 MPa (10 bar) User-selectable, based on mobile phase compressibility , solvents with ph < 2.3 should not contain acids which attack stainless steel Low pressure binary mixing/gradient capability using proprietary high-speed proportioning valve µl, dependent on back pressure; measured with water at 1 ml/min (water/caffeine tracer) 0 95 % or 5 100, user selectable < 0.2 % RSD or < 0.4 min SD, whatever is greater, at 1 ml/min; based on retention time at constant room 40 Specification Compendium

41 Pumps 1 Agilent 218 Solvent Delivery Module Agilent 218 Solvent Delivery Module Physical Specifications Table 27 Type Specifications Agilent 218 Purification Solution Specification Rated voltage Weight Dimensions (height x width x depth) VAC ( Absolute), Hz The Agilent 218 Purification Solution 1 may be wired for either: 115 V ±10 %, 50 /60 Hz single phase 230 V ±10 %, 50 /60 Hz single-phase 23.6 kg(52.0 lb) 197 x 292 x 464 mm (7.8 x 11.5 x 18.3 in) Line voltage V ±10 % Line frequency Power consumption Ambient operating Hz 550 VA 3 40 C Humidity % Operating altitude up to 2000 m The 218 System Pump is suitable for indoor use only and is classified Pollution degree 2 and Installation Category II (EN ). 1 All power supplies should be single phase AC, 3 wire system (active, neutral, ground) and should be terminated at an appropriate connection receptacle that is within reach of the system power cable. Specification Compendium 41

42 1 Pumps Agilent 218 Solvent Delivery Module Performance Specifications Table 28 Type Display Programs Performance specifications Agilent 218 Purification Solution Specification Backlit LCD with 2 lines, 48 characters Up to 100 methods with unlimited timed events Interface Digital serial input/output channel (RS-422) 3 programmable contact-closure relay outputs 5 contact-closure inputs 1 analog input (-0.5 V to +2.5 V), 18-bit A/D converter 1 programmable analog output (0 10 V ) Flow Accuracy Flow Reproducibility 1 % of selected flow rate or 0.05 % of maximum flow, whichever is larger (0.1 % for 5 ml/min heads) 0.1 % of selected flow or 0.05 % of maximum flow, whichever is larger (0.01 % for 5 ml/min heads) Connections 1/4-28 inlet flanged or gripper-type fitting 1/4-28 outlet for nut and ferrule Fluid Path 316 stainless steel, titanium, sapphire or ceramic, ruby, PCTFE, PTFE, or HDPE 42 Specification Compendium

43 Pumps 1 Agilent 218 Solvent Delivery Module Table 29 Pressure limits pump heads Nominal flow (ml/min) Range (ml/min) SST and Titanium (pressure maximum) PEEK (pressure maximum) psi 600 bar 60.0 MPa psi 414 bar 41.4 MPa psi 275 bar 27.6 MPa psi 241 bar 24.1 MPa 4000 psi 275 bar 27.6 MPa 4000 psi 275 bar 27.6 MPa 2000 psi 137 bar 13.8 MPa N/A Table 30 Performance specifications pressure modules Description/wetted materials Inlet fittings (in) Outlet fittings (in) Max. pressure (psi) Max. flow rate (ml/min) 10 ml/min, Titanium, FEP ¼-28 ¼ ml/min, Titanium, FEP ¼-28 ¼ ml/min, Titanium, FEP ¼-28 ¼ ml/min, PEEK, FEP ¼-28 ¼ ml/min, PEEK, FEP ¼-28 ¼ ml/min, PEEK, FEP ¼-28 ¼ ml/min, Titanium, FEP ¼-28 ¼ Uses cm (1/8 in.) ID tubing. Specification Compendium 43