600T EN Series Pressure Transmitters. Specification sheet. Model 624ES gauge/absolute with direct mount seal for pulp & paper application

Transcription

1 Specification sheet 6T EN Series Pressure Transmitters Model 6ES gauge/absolute with direct mount seal for pulp & paper application Base accuracy : ±.7% Reliable inductive sensing system coupled with the very latest digital technologies - ensures high performance at all process conditions Standardardized mechanical process interfaces - match precisely the process for pulp and paper industry applications HART - ma, Profibus PA, FF versions with plug-and-play electronics replacement - provides interchangeability for upgrading transmitter Local snap calibration and full management via hand terminal or PC-running software HART, Profibus PA, FF communications - allows integration with standard process bus CoMeter display option - offers HART Configuration capabilities combined with local indication The all new 6T Series transmitter The first choice pressure transmitter is now an even bigger choice Ecoefficient life cycle -ensures low environmental impact in compliance with LCA assessment to ISO standard

2 GENERAL DESCRIPTION Model 6ES detailed in this specification sheet integrates a direct mount seal on the positive side, having the negative side reference at atmospheric or vacuum pressure, respectively for gauge or absolute measurements. The integral seal is available in in and / in diaphragm size specifically designed for pulp and paper industry applications, providing a flush diaphragm to the process; this solution ensures the measure reliability avoiding all problems of crystallization/ polymerization, typical of pulps having high viscosity as in the paper mill. FUNCTIONAL SPECIFICATIONS Range and span limits Sensor code D E F Upper Range Limit (URL) 6 kpa 6 mbar 6 inho 6 kpa 6 bar 87 psi kpa bar 8 psi Lower Range Limit (LRL) 6ES with direct mount seal.7 kpa abs.7 mbar abs. mmhg.7 kpa abs.7 mbar abs. mmhg.7 kpa abs.7 mbar abs. mmhg Turndown ratio (TD) Span limits Maximum span = URL Minimum recommended span = URL/TD extended (can be further turndown to URL/TD maximum at no stated performances) Zero suppression and elevation Zero and span can be adjusted to any value within the range limits detailed in the table as long as: - calibrated span minimum span Damping Selectable time constant :,.,.,,,, 8 or 6 sec. Electromagnetic compatibility (EMC) Comply with EN 8- for emission and EN 8- for immunity requirements and test; CE marking. Turn on time Operation within specification in less than sec. with minimum damping. Insulation resistance > Vdc (terminals to earth) Temperature limits C ( F) Process Silicone oil or DC97-9 filling : - and + C (- and F) Lower process limit for Viton gasket: - C (- F) Ambient Operating limits : - and +8 (- and +8) Lower ambient limit for LCD indicators: - C (- F) Upper ambient limit for CoMeter : +7 C (+8 F) Storage Lower limit: - C (-8 F); - C (- F) for LCD indicators Upper limit:+ C (+8 F);+8 C (+8 F) for LCD indicators Normal Extended Maximum Overpressure limits (without damage to the transmitter) Lower :.7 kpa abs,.7 mbar abs,. mmhg Upper (transmitter sensor limit or flange / fitting rating of the seal, whichever is less) - model 6ES sensor code D, E, F : MPa, bar, psi - pulp & paper seal (S6D) - in size : MPa, bar, psi - / in size : MPa, bar, 7 psi Proof pressure The transmitter meets SAMA PMC 7. requirements and can be exposed without leaking to line pressure of up to 8 MPa, 8 bar, psi or two times the flange/fitting rating of the seal, whichever is less ELECTRICAL CHARACTERISTICS AND OPTIONS HART digital communication and to ma output Power Supply The transmitter operates from. to Vdc with no load and is protected against reverse polarity connection (additional load allows operations over Vdc). For EEx ia and intrinsically safe (FM, CSA and SAA) approval power supply must not exceed Vdc. MINIMUM OPERATING VOLTAGES no link on output indicator plugs with optional output LCD indicator and surge protection with CoMeter with optional output LCD indicator with optional surge protection with optional output analog indicator with integral display (volts) Load limitations - - ma and HART total loop resistance : (ohms) Total loop resistance 6 Supply voltage - min. operating voltage (Vdc) R(kΩ) = to ma and HART digital communication to ma only. (ref.) (volts) Supply voltage Optional indicators Output meter (user adjustable) - LCD : /-digit with mm (/8 in) high, 7-segment characters. Engineering unit labels are provided. LCD output meter may be calibrated within the range -999 to with a span adjustable between and 998 units. (Display of decimal point, if required, is switch selectable) - analog : 6 mm (. in) scale on 9

3 Integral display - LCD: -digit with 8 mm. (/6 in) high, 9-segment alphanumeric characters. User-definable display mode with HART communication : - process variable in engineering units, or - percent of range, or - process variable in engineering units and percent of range alternating every seconds, or - process variable in engineering units and digital output ( to ma) alternating every seconds. Factory selectable display mode with to ma output : - percent of range - percent of range and to ma output alternating every seconds Display also indicates diagnostic messages. CoMeter - -digit LCD (± counts programmable) with 7.6 mm. high ( in), 7-segment numeric characters plus sign and digital point - -segment LCD bargraph display (% per segment) - 7-digit LCD with 6 mm. high (. in), -segment alphanumeric characters. Optional surge protection Up to. kv ( ka discharge current) of 8 µs rise time/ µs decay. Output signal Two-wire to ma dc, user-selectable for linear or square root output, power of / or /, th order or two nd order switching point selectable programmable polynomial output. HART communication provides digital process variable (%, ma or engineering units) superimposed on to ma signal, with protocol based on Bell FSK standard. Output current limits (to NAMUR standard) Overload condition - Lower limit :.8 ma dc - Upper limit :.8 ma dc Transmitter failure mode (to NAMUR standard) The output signal can be user-selected to a value of.6 or.6 ma on gross transmitter failure condition, detected by selfdiagnostics. In case of CPU failure the output is driven <.6 ma or >.6 ma. Profibus PA output Power supply The transmitter operates from. to Vdc with no polarity. For EEx ia approval power supply must not exceed Vdc. Intrinsic safety installation according to FISCO model. Current consumption - operating (quiescent) :. ma - communicating :. ma - fault current limiting : 6 ma max. Output signal Physical layer in compliance to IEC 8-/EN 68- with transmission to Manchester II modulation, at. kbit/sec. Output interface Profibus PA communication according to Profibus DP7 Part /DIN 9 part - compliant to Profiles. Class A & B for pressure transmitter; ident. number B HEX. Output update time : ms Function blocks analog input, transducer, physical Optional indicator Integral display - LCD : digit characters, displaying process variable in engineering units or as percentage value. Display also indicates diagnostic messages. Transmitter failure mode On gross transmitter failure condition, detected by self-diagnostics, the output signal can be driven to defined conditions, selectable by the user as safe, last valid or calculated value. FOUNDATION fieldbus output Device type Link Active Scheduler (LAS) capability implemented Power supply The transmitter operates from 9 to Vdc with no polarity. For EEx ia approval power supply must not exceed Vdc. Intrinsic safety installation according to FF application guide Current consumption - operating (quiescent) :. ma - communicating :. ma - fault current limiting : 6 ma max. Output signal Physical layer in compliance to IEC 8-/EN 68- with transmission to Manchester II modulation, at. kbit/sec. Function blocks/execution period standard Analog Input blocks / msec. max (each) standard PID block / 7 msec. max. Additional blocks Transducer block, standard Resource block, custom Pressure with calibration block Number of link objects : Number of VCRs : Output interface FOUNDATION fieldbus digital communication protocol to standard H, compliant to specification V..; FF registration IT. Optional indicator Integral display - LCD : digit characters, displaying process variable in engineering units or as percentage value. Display also indicates diagnostic messages. Transmitter failure mode The output signal is "frozen" to the last valid value on gross transmitter failure condition, detected by self-diagnostics which also indicate a BAD conditions. If electronic failure or short circuit occur the transmitter consumption is electronically limited at a defined value (6 ma approx), for safety of the network.

4 PERFORMANCE SPECIFICATIONS Stated at ambient temperature of C ± K (7 F ± ), relative humidity of % ±%, atmospheric pressure, mounting position with vertical diaphragm and zero based range for transmitter with isolating diaphragms in AISI 6 L ss or Hastelloy and silicone oil fill and HART digital trim values equal to - ma span end points, in linear mode. Unless otherwise specified, errors are quoted as % of span. Some performance data are affected by the actual turndown (TD) as ratio between Upper Range Limit (URL) and calibrated span. IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR CODE PROVIDING THE TURNDOWN VALUE AS LOWEST AS POSSIBLE TO OPTIMIZE PERFORMANCE CHARACTERISTICS. Accuracy rating % of calibrated span, including combined effects of terminal based linearity, hysteresis and repeatability. For fieldbus versions SPAN refer to analog input function block outscale range.. - ±.7% for TD from : to : URL - ±.7% x Span for TD from : to : Optional indicators accuracy integral display (microprocessor driven) : no error analog output meter : ± % full scale deflection LCD output meter : ±.% of calibrated span ± unit CoMeter - digital : ±.% of max span(6 ma) ± digit - analog (bargraph) : % Operating influences Temperature effects per K (6 F) ambient temperature change on transmitter sensor between the limits of - C to + 6 C (- to + F) - in pulp & paper seal : ± (.% URL +.% span) - /in pulp & paper seal : ± (.% URL +.% span) Multiply by. the above coefficients for K (6 F) change between the limits of - to - C (- to F) and of +6 to +8 C (+ to 8 F) per K (6 F) process temperature change on seal diaphragm between the process operating temperature limits of - to C (- to 8 F) - in pulp & paper seal :.6 kpa, 6 mbar,. inho - /in pulp & paper seal :. kpa, mbar,.8 inho Multiply by. the above values for K (6 F) change between the limits of - to - C (- to - F) and of + to + C (+8 to F) The total zero temperature error is the combination of the two above effects, as applicable due to application temperatures. Optional LCD output meter ambient temperature per K (.8 F) change between the limits of - and +8 C (- and + 76 F) Total effect : ± (. x span units +.) of reading. Supply voltage Within voltage/load specified limits the total effect is less than.% of URL per volt. Load Within load/voltage specified limits the total effect is negligible. Radio frequency interference Total effect : less than.% of span from to MHz and for field strengths up to V/m when tested with shielded conduit and grounding, with or without meter. Meets IEC 8. Common mode interference No effect from V Hz, or Vdc. Series mode interference No effect from V Hz. PHYSICAL SPECIFICATIONS (Refer to ordering information sheets for variant availability related to specific model or versions code) Materials Process isolating diaphragms (*) AISI 6 L ss, Hastelloy C76 ; Process connection (*) AISI 6 L ss. Gaskets (*) Viton for in size PTFE for /in size Sensor housing : AISI 6 L ss Sensor fill fluid Silicone oil (DC) Seal fill fluid Silicone oil (DC), DC 97-9 PHARMA B-GRADE Electronic housing and covers Barrel version - Low-copper content aluminium alloy with baked epoxy finish; - AISI 6 L ss. Covers O-ring: Buna N. Local zero and span adjustments: Glass filled polycarbonate plastic (removable) Tagging AISI 6 ss data plate attached to the electronics housing. Optional CoMeter ambient temperature Total reading error per K (6 F) change between the ambient limits of - and +7 C (- and +8 F): ±.% of max span (6 ma).

5 Calibration - Standard: at maximum span, zero based range, ambient temperature and pressure - Optional: at specified range and ambient conditions; or at operating temperature. Optional extras Output indicator: plug-in rotatable type, LCD or analog. Standard LCD output meter scale is to % linear; special linear scale to specified range and engineering unit is available.standard analog output meter scale is to % linear or to square-root; special graduation is available. Supplemental customer tag AISI 6 ss tag screwed/fastened to the transmitter for customer's tag data up to a maximum of characters and spaces on one line for tag number and tag name, and up to a maximum of spaced strings of characters each for calibration details (lower and upper values plus unit). Special typing evaluated on request for charges. Surge protection (not available with Profibus PA and FF output) Material traceability Environmental protection Wet and dust-laden atmospheres The transmitter is dust and sand tight and protected against immersion effects as defined by IEC 9 (989) to IP 67 (IP 68 on request) or by NEMA to X or by JIS to C9 Hazardous atmospheres With or without output meter/integral display INTRINSIC SAFETY/EUROPE: ATEX/BASEEFA approval EC-Type Examination Certificate no. BAS 99ATEX 8 - (HART) II GD T C, EEx ia IIC T6/T (- C Ta + C) T9 C, EEx ia IIC T (- C Ta +8 C) - (FOUNDATION Fieldbus) II GD T7 C, EEx ia IIC T (- C Ta +6 C) EC-Type Examination Certificate no. BAS ATEX - (PROFIBUS-PA) II GD T7 C, EEx ia IIB T (- C Ta +6 C) TYPE "N"/EUROPE : ATEX/BASEEFA type examination Design compliance by Certificate no. BAS ATEX 8X - (HART) II GD T C, EEx nl IIC T (- C Ta + C) T9 C, EEx nl IIC T (- C Ta +8 C) - (FOUNDATION Fieldbus) II GD T7 C, EEx nl IIC T (- C Ta +6 C) Design compliance by Certificate no. BAS ATEX 8X - (PROFIBUS-PA) II GD T7 C, EEx nl IIB T (- C Ta +6 C) FLAMEPROOF/EUROPE: ATEX/CESI approval; EC-Type Examination Certificate no. CESI ATEX II / GD T8 C, EEx d IIC T6 (- C Ta +7 C) T9 C, EEx d IIC T (- C Ta +8 C) CANADIAN STANDARDS ASSOCIATION and FACTORY MUTUAL : - Explosionproof: Class I, Div., Groups A, B, C, D - Dust ignitionproof : Class II, Div., Groups E, F, G - Suitable for : Class II, Div., Groups F, G; Class III, Div., - Nonincendive: Class I, Div., Groups A, B, C, D - Intrinsically safe: Class I, II, III, Div., Groups A, B, C,D,E, F, G STANDARDS AUSTRALIA (SAA) TS/WCA Approval (HART only) Conformity Certificate no. AUS Ex 7X Ex d IIC T (Tamb +8 C)/T6 (Tamb +7 C) Class Zone ; Ex ia IIC T (Tamb +8 C) /T (Tamb + C) T6 Class Zone Process connections Pulp & Paper seal (mod. S6D) - in flush diaphragm suitable for weld spud by fixing screw - /in flush diaphragm with M x. threaded connection. Electrical connections Two / NPT or Mx. or PG. or / GK threaded conduit entries, direct on housing; straight or angle Harting HAN connector and one plug, on request. Terminal block HART version Three terminals for signal/external meter wiring up to. mm ( AWG) and three connection points for test and communication purposes. Fieldbus versions Two terminals for signal wiring (bus connection) up to. mm ( AWG) Grounding Internal and external 6 mm ( AWG) ground termination points are provided. Mounting position Transmitter can be mounted in any position. Electronics housing may be rotated to any position. A positive stop prevents over travel. Mass (without options). to kg approx ( to 6 lb) according to specified seal(s) options; add. kg (. lb) for AISI housing. Add 6 g (. lb) for packing. Packing Carton Hastelloy is a Cabot Corporation trademark Viton is a Dupont de Nemour trademark (*) Wetted parts of the transmitter.

6 CONFIGURATION Transmitter with HART communication and to ma Standard configuration Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and configured as follows: Engineering Unit: Specify code option ma: Zero ma: Upper Range Limit (URL) Output : Linear Damping: sec. Transmitter failure mode: Upscale Software tag characters: Blank Optional LCD output indicator : to.% linear Any or all the above configurable parameters, including Lower range-value and Upper range-value which must be the same unit of measure, can be easily changed using the HART hand-held communicator. The transmitter database is customized with specified flange type and material, O-ring and drain/vent materials and meter code option. Custom configuration (option) The following data may be specified in addition to the standard configuration parameters: Descriptor : 6 alphanumeric characters Message: alphanumeric characters Date: Day, month, year Damping: Seconds Transmitter with Profibus PA communication Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and configured as follows: Measure Profile: Pressure Engineering Unit: kpa Output scale %: Lower Range Limit (LRL) Output scale %: Upper Range Limit (URL) Output : Linear Hi-Hi Limit : Upper Range Limit (URL) Hi Limit : Upper Range Limit (URL) Low Limit : Lower Range Limit (LRL) Low-Low Limit : Lower Range Limit (LRL) Limits hysteresis:.% of output scale PV filter: sec. Address (settable by local key): 6 Tag : alphanumeric characters Any or all the above configurable parameters, including Lower range-value and Upper range-value which must be the same unit of measure, can be easily changed by a PC running the configuration software Smart Vision with DTM for 6T or 6T template for Siemens Simatic PDM System. The transmitter database is customized with specified flange type and material, O- ring and drain/vent materials and meter code option. Custom configuration (option) The following data may be specified in addition to the standard configuration parameters: Descriptor : alphanumeric characters Message: alphanumeric characters Date: Day, month, year PV filter: Seconds Transmitter with FOUNDATION fieldbus communication Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and configured as follows: Measure Profile: Pressure Engineering Unit: kpa Output scale %: Lower Range Limit (LRL) Output scale %: Upper Range Limit (URL) Output : Linear Hi-Hi Limit : Upper Range Limit (URL) Hi Limit : Upper Range Limit (URL) Low Limit : Lower Range Limit (LRL) Low-Low Limit : Lower Range Limit (LRL) Limits hysteresis:.% of output scale PV filter time: sec. Tag : alphanumeric characters Any or all the above configurable parameters, including the range values, can be changed using any host compliant to FOUNDA- TION fieldbus. The transmitter database is customized with specified flange type and material, O-ring and drain/vent materials and meter code option. Available engineering units of pressure measure are : Pa, kpa, MPa inho@ C, mmho@ C, psi inho@ C, ftho@ C, mmho@ C inhg, mmhg, Torr g/cm, kg/cm, atm mbar, bar 6

7 MOUNTING DIMENSIONS (not for construction unless certified) 6ES with pulp and paper seal S6D - in size to spud with screw fixing Adjustments Identification tag Min. clearance to remove the cover 7 (.67) 6 (.) 7 (.) 6 (.) 7 (.67) Barrel type housing Electronic side Integral display housing (.9) Certification label Terminal side Output meter housing /6" 8-UNC fixing hole for spud 6 (.6) 8 (.7). (.78) ø 8 (.) ø 6.7 (.). () in spud Gaskets ø.8 (.) ø 9. (.6) ø. (.) 6ES with pulp and paper seal S6D - /in size to screwed spud Adjustments Identification tag Min. clearance to remove the cover 7 (.67) 6 (.) 7 (.) 6 (.) 7 (.67) Barrel type housing Certification label Electronic side (.9) Terminal side Integral display housing 8 (.7) Output meter housing 6 (.6) 6.7 (.) Mx..8 (.8) /" in spud ø 6 (.) ø (.) Mx. CH6 exag 7

8 % Kent-Taylor 9 F F F F REVIEW A B C J K L S T U 7 PV CONF TRIM D E F M N O V W X % & / SERIAL LINK G H I P Q R 6 Y Z # HART Version ELECTRICAL CONNECTIONS FIELDBUS Versions Internal ground termination point M+ - 8 Remote indicator Internal ground termination point + M - + Line load ohm min + + BUS CONNECTIONS Fieldbus line Harting pin identification - TEST COMM + Test points - ma External ground termination point GND Hand-held communicator Power source - Optional HART hand-held communicator may be connected at any wiring termination point in the loop, providing the minimum resistance is ohm. If this is less than ohm, additional resistance should be added to allow communications. 69HT - Receiver External ground termination point 8

9 ORDERING INFORMATION model S6D direct mount seal for pulp and paper application Select one character or set of characters from each category and specify complete catalog number, in addition to the 6ES transmitter code PRODUCT CODE abc d ef g h i j kl m no BASE NUMBER NUMBER OF REMOTE SEALS MOUNTING CONNECTION MATERIAL/TYPE OTHER WETTED MATERIAL DIAPHRAGM MATERIAL EXTENSION LENGTH CAPILLARY SYSTEM LENGTH PROCESS 'O' RING OPTIONS abc BASE NUMBER - st to rd characters Pulp and paper application seal Code S6D d NUMBER OF REMOTE SEALS - th character One for direct mount ef MOUNTING CONNECTION MATERIAL/TYPE - th and 6th characters AISI 6 L ss / in ANSI / M x. threaded for fixing to spud AISI 6 L ss in ANSI / screw fixing to spud V U g OTHER WETTED MATERIAL - 7th character Same as diaphragm material h DIAPHRAGM MATERIAL - 8th character AISI 6 L ss Hastelloy C76 i j EXTENSION LENGTH - 9th character CAPILLARY - th character Fill fluid Silicone oil (DC ) DC 97-9 PHARMA B-GRADE A Q kl SYSTEM LENGTH m (feet) - th and th characters (direct mount) m PROCESS 'O' RING - th character Viton for in size - PTFE for / in size no OPTIONS - th and th characters Spud for / in version connection (available only for version V on "ef" position) Spud/screw for in version connection (available only for version U on "ef" position) N N Hastelloy is a Cabot Corporation trademark Viton is a Dupont de Nemour trademark 9

10 ORDERING INFORMATION model 6ES Transmitter with direct mount seal S6D Select one character or set of characters from each category and specify complete catalog number. Refer to supplementary code and specify another number for each transmitter if additional options are required. PRODUCT CODE abcde fg h i j k l m n op BASE MODEL SENSOR PROCESS CONNECTION REFERENCE CHAMBER OUTPUT ELECTRICAL CERTIFICATION TOP WORKS ELECTRICAL OPTIONS abcde BASE MODEL - st to th characters Pressure transmitter with integral direct mount seal Code 6ES f SENSOR Span limits - 6th character 8 and 6 kpa and 6 kpa and kpa 8 and 6 mbar. and 6 bar. and bar and 6 inho. and 87 psi 7. and 8 psi D E F g 7th character Diaphragm material AISI 6 L ss Fill fluid Silicone oil h PROCESS CONNECTION - 8th character All-welded direct mount seal, Pulp & Paper (to be coded separately as S6D) P i REFERENCE CHAMBER (negative) - 9th character At atmospheric pressure for gauge measurement At vacuum for absolute measurement B W j th character Use code k th character Use code l th character OUTPUT HART digital communication and to ma Profibus PA communication FOUNDATION Fieldbus Communication G P F m ELECTRICAL CERTIFICATION - th character General Purpose ATEX Group II Category / GD - Flameproof EEx d CESI approval ATEX Group II Category GD - Intrinsic Safety EEx ia BASEEFA approval ATEX Group II Category GD - Type of protection "N" EEx nl design compliance Factory Mutual (FM) and Canadian Standard Association (CSA) approvals (only with /" NPT and M electrical connection) Intrinsic Safety and Flameproof to Standards Australia SAA approval Ex ia IIC T6/T/T + Ex d IIC T6/T Note : not available with output code P and F at position "l" F L N 8 W Compliance to NACE class II bolting, according to specification MR7, latest revision

11 ORDERING INFORMATION model 6ES Transmitter with direct mount seal S6D n TOP WORKS - th character Housing material Aluminium alloy (Barrel version) AISI 6 L ss (Barrel version) Note : requires certification code at position "m" Note : not available with output code P and F at position "l" Electrical connection /" NPT M x. (CM ) Pg. /" GK Harting HAN connector - straight entry (Note, ) Harting HAN connector - angle entry (Note, ) /" NPT M x. (CM ) Pg. /" GK 6 A C D F o ELECTRICAL OPTIONS - th character Internal meter type Digital LCD output indicator linear -%, user scalable Digital LCD output indicator linear scale (specify range and engineering units) Analog output indicator linear -% scale Analog output indicator, special graduation (to be specified for linear scale ) Digital LCD integral display Digital LCD integral display and digital LCD output indicator linear - ma Digital LCD integral display and analog output indicator linear -% scale Programmable signal meter and HART configurator (CoMeter) Programmable signal meter and HART configurator (CoMeter) and digital LCD integral display Note : not available with output code P and F at position "l" 7 9 A C E P R 6th character p Electrical options Standard terminal block Surge protector Terminal block for external meter Note : not available with output code P and F at position "l" Labels language English German Italian English German Italian English German Italian

12 ORDERING INFORMATION Select one character or set of characters from each category and specify complete catalog number in addition to each transmitter code, if required. PRODUCT CODE ab c d e f BASE MODEL CONFIGURATION CALIBRATION PROCEDURE INTEGRAL MOUNTING OF ASSOCIATED INSTRUMENTATION ab BASE MODEL - st to nd characters Supplementary code Code SC c CONFIGURATION - rd character Standard - Pressure = kpa; Temperature = deg. C Standard - Pressure = inho/psi (@ C); Temperature = deg. F Standard - Pressure = inho/psi (@ C); Temperature = deg. F Standard - Pressure = inho/psi (@ C); Temperature = deg. C Standard - Pressure = inho/psi (@ C); Temperature =- deg. C Custom C d CALIBRATION - th character Calibration range Calibration Certificate Standard (max span = to URL) At specified range Reference temperature Operating temperature Reference temperature Operating temperature Yes ( copies) Yes ( copies) Yes ( copies) Yes ( copies) e th character PROCEDURE Material traceability To EN -..B (certificates for flanges, adapters, diaphragms) To EN -. (declaration for instrument) A B f INTEGRAL MOUNTING OF ASSOCIATED INSTRUMENTATION - 6th character The Company's policy is one of continuous product improvement and the right is reserved to modify the specifications contained herein without notice. SS/6ES-PP Rev. ABB Ltd. Howard Road St. Neots Cambridgeshire PE9 EU UK Tel: + () 8 7 Fax: + () ABB Inc. East County Line Road Warminster, PA 897 USA Tel: Fax: ABB Instrumentation spa Via Statale 6 Lenno (Como) Italy Tel: +9 8 Fax: