Series 01 Type 01, 02

Transcription

1 Series 01 Type 01, 02 ThermalProtectors

2 ThermalProtectors for nominal currents up to 2.5 Series 01 Type 01 Type 02 Version C, S, L, N Benefits & dvantages The outstanding quality level of our ThermalProtectors of the Series 01 satisfies highest demands for safety and reliability. They are provided with a patented, fully developed and reliable switching device system. Compact & Pressure Stable - Ideal for installation in limited space, very suitable for mounting into and onto windings Safe, Reliable & Durable - Constant contact pressure over the whole temperature range - Over 70 tests conducted during the production process ensure reliability - pprovals world-wide - Very fast switching; therefore short arcing influence on the contacts Temperature-sensitive - Reproducible SwitchingTemperature induced by mechanical unstressed and electrically unloaded bimetal disc - Factory-adjusted NominalSwitchingTemperature (NST) Fast - Excellent thermal coupling induced by a small-scaled, low-weighted switching device Flexible - Wide-band mains supply range - Extremely large assortment of lead-wires and solid wires available for connection General data T T Functions & Types C01 S01 L01 N01 CK1 SK1 LK1 NK1 C02 S02 L02 N02 Max. pressure stability (housing) / (max. mechanical load) 450 N (45kg) High-Voltage Insulation (HiPot) Version C -- Version S 2 kv Version L 2 kv Version N -- Suitable for installment in protection class (insulation) I (1), ll (2) Degree of protection IPOO Impregnation resistance suitable Contact bounce time [ms] < 1 Contact resistance (acc. to MIL-Standard R 5757) [m ] < 50 Vibration proof (at Hz) [m/s2] 100 (10g) ResettingSwitchingTemperature Range RST dependant on Series please inquire - - Standard [ C] -- > 35 - UL-Standard Range [ C, K] NST -30 ±15 - CS-Standard Range [ C, K] NST NST -50 NST = NominalSwitchingTemperature, see technical data RST = ResettingSwitchingTemperature Normally closed (NC), Resetting, Standard Normally open (NO), Resetting, Standard Bimetal switch fter reaching its factory-adjusted NominalSwitching Temperature (NST) the bimetal disc suddenly turns over from its stable initial position into a stable end position and thereby activates the switching device. Normally closed (NC) Contacts open and switch off the supply => direct disconnection (01) Normally open (NO) Contacts close and activate the supply => i.e. switching on of signal units (02) Resetting after cooling down to below its factory-adjusted ResettingSwitchingTemperature (RST) the switching device suddenly snaps back into its initial position Max. Switching current Imax Maximum current in disturbed condition => i.e. during short circuit or on locked-rotor condition You develop a successful product we provide you with the appropriate ThermalProtector. Whether you want to develop a new product or if you want to attain the highest quality standards in your production do not compromise! Our Know-How as well as our wide range of products will set you no limits. Standard or special solution You develop innovative concepts we provide you with suitable thermal protection. Our exceptionally large standard programme already offers you a multitude of choices. Furthermore, we offer specific solutions which are developed in our laboratories to meet your special requirements. Thereby you can take advantage of more than 35 years of experience in product development achieved in close cooperation with wellknown producers in various industries. Individual solutions are our speciality - challenge us! T cc. to Thermik Test For others please inquire Subject to change

3 Technical Data The listed specifications and information are based on tests and test series. They are of a standard nature and therefore deviations may occur in connection with specific applications. The suitability for a specific application must be individually tested by the user. Please contact us for advise and support. Version C01, CK1 and C02 are the basis for the following variations. Standard version is without base insulation - Multi-purpose usability - Optimal thermal coupling of the switching device - Live contact of housing therefore - when fitting - base insulation has to be provided. S01, SK1 and S02 are provided with an insulation cap for base insulation - Various types with different insulation materials and protection classes available - Suitable for mounting into and onto windings of electro-motors, transformers or ballasts. C01 C02 S01 S02 K1= 01 for the lower temperatures Switching contact type NC = normally closed, NO = normally open Insulated: insulation cap Version S Temperature NominalSwitchingTemperature (NST), in 5K-steps [ C] Tolerance range Standard- Tol [K] Voltage Rated voltage Un 50/60 Hz [V C ] Max. C-operating voltage range up to... [V C ] Max. DC-operating voltage range up to... [V DC ] Current / Switching Cycles Rated current In 50/60 Hz t Un: ohmic - cos = 1.0 [] / [n] t Un: inductive - cos = 0.6 [] / [n] L t Un: inductive - cos = [] T t 500 V C : ohmic - cos = 1.0 [] / [n] T t 500 V C : inductive - cos = 0.6 [] / [n] T Max. switching current Imax at Un - cos = 1,0 [] / [n] pprovals NST: 70 C-180 C, K1: 60 C-180 C VDE/IEC NST: 60 C-200 C UL NST: 70 C-200 C, K1: 60 C-200 C CS/cUL NST: 70 C-180 C BEB NST: 70 C-180 C SEMKO L pprovals for Ballasts Dimensions (Standard) NC NO NC NO (VDE,IEC,BEB,SEMKO,CS) 277 (UL) 250 (VDE,IEC,BEB,SEMKO,CS) 277 (UL) /10,000 (VDE,IEC,BEB,SEMKO) 2.5/10,000 (VDE,IEC,BEB,SEMKO) 1.6/10,000 (VDE,IEC,BEB,SEMKO) 1.6/10,000 (VDE,IEC,BEB,SEMKO) 1.8 (VDE,IEC) 1.8 (VDE,IEC) 5.0/2,000 dependant on version (RST, insulation etc.) acc. to inquiry 5.0/2,000 Diameter Ød [mm (inch)] Overall height (with standard connection) h [mm (inch)] Length Insulation cap (S) l [mm (inch)] feasible wiring connections Lead wire Single wire Standard wiring connection 9.0 (.354) 9.0 (.354) 4.3 (.169) 4.3 (.169) Lead wire: 0.25 mm 2 /WG (.370) 9.4 (.370) 4.8 (.189) 4.8 (.189) 16 (.630) 16 (.630) Lead wire: 0.25 mm 2 /WG 22 T cc. to Thermik Test For others please inquire Yes No / not applicable Subject to change

4

5 Typical current sensitivity characteristics special feature of the Series 01 is that the switch is a temperature-sensitive switch. In normal operation and loads up to nominal current, self-heating of the switch is extremley low. Therefore the lowering of the switching temperature caused by self-heating will be within the NominalSwitchingTemperature tolerance. Please also refer to Benefits & dvantages. Standards: pprovals Please always list the needed approvals separetely onto your order. VDE acc. to EN ENEC acc. to IEC How to order CB-Report acc. to IEC (IEC 730) UL acc. to UL 2111 UL 873 CS acc. to C22.2 Features of automatic action acc. to IEC/EN 60730: 2B/2C/2BM/2CM. Existing Standard mendments acc. to IEC/EN 60730: -1; -2-1; -2-3; CC- CENELEC Certification greement acc. to EN Thermik products correspond to the respective EU-directives / rules BEB acc. to EN SEMKO acc. to EN CQC acc. to IEC Use the quality of our products to safeguard the quality of your products. From the first stage of production until delivery our products undergo more than 70 quality inspections. Specially designed, fully automatic control devices guarantee an optimal quality standard. Needless to say, these high demands are met on all our production sites. Single switch Duplex configuration Triplex configuration Ready Reckoner 1 mm <=> inch (") 25.4 mm <=> 1 inch (") 100 mm <=> 3.94 " 300 mm <=> " C <=> ( F - 32) / 1.8 F <=> x C It s good to know - that our quality and flexibility open up a whole new range of possibilities to you. Order samples Single with L1= L2 Single with L1= L2 Duplex L1 - L3 Triplex L1 - L4 NominalSwitchingTemperature (NST) [ C] Tolerance Range [ ± K] Lengths [mm] Version Type L1 S L2 L / 0200 L3 C / 0100 / 0200 L4 S / 0180 / 0180 / 0650 L1 L2 L3 L4 Thermik produces the smallest thermal protectors available on the market and in addition PTC Thermistor sensors in miniature design for rounding up the product range for use in your compact products. We also offer a unique variety of technical solutions our standard programme alone comprises of more than 2000 models with connecting wires in different lengths, colours, cross-sections and insulation materials. Subjekt to change

6 Thermik Design concept and aims to suit customers Competence is our asset For more than 35 years the name Thermik has stood for efficiency, flexibility and reliability in the production of Thermal protectors. We combine experience and Know-How with innovation and consistent orientation towards the objectives of our customers. In this way we constantly extend and improve our range of products. nd if on occasion your requirements cannot be fulfilled by our standard programme, we develop a customized solution together with you. Our highly qualified and competent employees put your wishes into effect. Irrespective of where you are manufacturing we supply all over the world. Our subsidiaries in Germany, Malaysia and US are all equally equipped production sites and their machinery fulfils the highest standards. We are therefore well prepared for the efficient production of large and small quantities. This flexibility guarantees you highest supply reliability. worldwide net of representatives offers you specialist advice on site. Our products have all the internationally required approvals. We continuously optimise materials, working processes and production materials. Safety, Quality and Customer Requirements have the highest priority. dditional brochures informing you of other products within product range are available on request. Thermik Geraetebau GmbH Im ltgefaell 8 D Pforzheim POBox D Pforzheim Tel Fax info@thermik.de DIN EN ISO 9001 Thermik is world-wide with all its production sites certified to DIN EN ISO 9001 Certificate Register No Certificate Register No TMS Challenge us with your requirements - we will show you the solutions! marketing concept Rev /4 2,500